| ;/*it is used for attaching while zx297510evb running*/ | |
| ;do ./boot_attach_CortexA9.cmm | |
| GLOBAL &VMLINUX_PATH | |
| GLOBAL &SOURCE_PATH | |
| GLOBAL &DDR_BASE | |
| &SOURCE_PATH="..\..\linux_plat\base\linux\kernels\linux-3.4.5" | |
| &VMLINUX_PATH="..\..\linux_plat\base\linux\kernels\linux-3.4.5\vmlinux" | |
| &DDR_BASE=0x20440000 | |
| area.reset | |
| sYmbol.RESet | |
| MMU.RESet | |
| ; setup of ICD | |
| print "initializing..." | |
| SYStem.CPU CortexA53 ; ;ZX297520v3 CortexA53 core | |
| SYStem.Option MMUSPACES ON ; enable space ids to virtual addresses | |
| SYStem.JtagClock 3.0MHz ; use adaptive clocking for most speed | |
| system.option resbreak off | |
| system.option enreset off | |
| Sys.Config.COREBASE 0x80410000 ; | |
| Sys.Config.CTIBASE 0x80420000 | |
| Sys.Config.debugaccessport 0 | |
| Sys.Mode PREPARE | |
| wait 0.1s | |
| sys.mode attach | |
| SETUP.IMASKASM ON ; lock interrupts while single stepping | |
| ; Load the Linux kernel symbols into the debugger | |
| print "loading Linux kernel symbols..." | |
| ;Data.LOAD.Elf &VMLINUX_PATH /gnu /nocode /SourcePATH ..\..\..\..\ | |
| Data.LOAD.Elf &VMLINUX_PATH /gnu /nocode /strippart "linux-3.4.5" /SourcePATH ..\linux-3.4.5 | |
| ; Map the virtual kernel symbols to physical addresses | |
| ; to give the debugger access to it before CPU MMU is | |
| ; initialized | |
| MMU.FORMAT LINUX swapper_pg_dir 0xc0040000--0xc30fffff &DDR_BASE | |
| TRANSlation.COMMON 0xbf000000--0xffffffff ; common area for kernel and processes | |
| TRANSlation.TableWalk ON ;debugger uses table walk to decode virtual address | |
| TRANSlation.ON ;switch on debugger address translation | |
| ; set source path | |
| print "set source path ..." | |
| sYmbol.SourcePATH.RESet | |
| sYmbol.SourcePATH.SetBaseDir &SOURCE_PATH | |
| sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\arch\arm | |
| sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\arch\arm\mach-zx297520v3 | |
| sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\init | |
| sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\kernel | |
| ;sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\drivers\base | |
| ;sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\drivers\tty | |
| ;sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\drivers\gpio | |
| ;sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\drivers\i2c | |
| ;sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\drivers\usb | |
| ;sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\drivers\mmc | |
| ;sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\mm | |
| sYmbol.SourcePATH.SetRecurseDir &SOURCE_PATH\drivers | |
| ; Initialize Linux Awareness | |
| ; Note that the Linux awareness needs the kernel symbols to work | |
| print "initializing multitask support..." | |
| TASK.CONFIG .\linux ; loads Linux awareness (linux.t32) | |
| MENU.ReProgram .\linux ; loads Linux menu (linux.men) | |
| HELP.FILTER.Add rtoslinux ; add linux awareness manual to help filter | |
| MENU.ReProgram .\sys\board ; add board tools | |
| ; Group kernel area to be displayed with red bar | |
| GROUP.Create "kernel" 0xc0000000--0xffffffff /RED | |
| GROUP.Create "module" 0xbf000000--0xbfffffff /blue | |
| ; Ok, we're done, let's start Linux | |
| break | |
| enddo | |