zte's code,first commit
Change-Id: I9a04da59e459a9bc0d67f101f700d9d7dc8d681b
diff --git a/ap/lib/libnl/libnl-3.2.25/include/linux/can/netlink.h b/ap/lib/libnl/libnl-3.2.25/include/linux/can/netlink.h
new file mode 100644
index 0000000..14966dd
--- /dev/null
+++ b/ap/lib/libnl/libnl-3.2.25/include/linux/can/netlink.h
@@ -0,0 +1,122 @@
+/*
+ * linux/can/netlink.h
+ *
+ * Definitions for the CAN netlink interface
+ *
+ * Copyright (c) 2009 Wolfgang Grandegger <wg@grandegger.com>
+ *
+ */
+
+#ifndef CAN_NETLINK_H
+#define CAN_NETLINK_H
+
+#include <linux/types.h>
+
+/*
+ * CAN bit-timing parameters
+ *
+ * For further information, please read chapter "8 BIT TIMING
+ * REQUIREMENTS" of the "Bosch CAN Specification version 2.0"
+ * at http://www.semiconductors.bosch.de/pdf/can2spec.pdf.
+ */
+struct can_bittiming {
+ __u32 bitrate; /* Bit-rate in bits/second */
+ __u32 sample_point; /* Sample point in one-tenth of a percent */
+ __u32 tq; /* Time quanta (TQ) in nanoseconds */
+ __u32 prop_seg; /* Propagation segment in TQs */
+ __u32 phase_seg1; /* Phase buffer segment 1 in TQs */
+ __u32 phase_seg2; /* Phase buffer segment 2 in TQs */
+ __u32 sjw; /* Synchronisation jump width in TQs */
+ __u32 brp; /* Bit-rate prescaler */
+};
+
+/*
+ * CAN harware-dependent bit-timing constant
+ *
+ * Used for calculating and checking bit-timing parameters
+ */
+struct can_bittiming_const {
+ char name[16]; /* Name of the CAN controller hardware */
+ __u32 tseg1_min; /* Time segement 1 = prop_seg + phase_seg1 */
+ __u32 tseg1_max;
+ __u32 tseg2_min; /* Time segement 2 = phase_seg2 */
+ __u32 tseg2_max;
+ __u32 sjw_max; /* Synchronisation jump width */
+ __u32 brp_min; /* Bit-rate prescaler */
+ __u32 brp_max;
+ __u32 brp_inc;
+};
+
+/*
+ * CAN clock parameters
+ */
+struct can_clock {
+ __u32 freq; /* CAN system clock frequency in Hz */
+};
+
+/*
+ * CAN operational and error states
+ */
+enum can_state {
+ CAN_STATE_ERROR_ACTIVE = 0, /* RX/TX error count < 96 */
+ CAN_STATE_ERROR_WARNING, /* RX/TX error count < 128 */
+ CAN_STATE_ERROR_PASSIVE, /* RX/TX error count < 256 */
+ CAN_STATE_BUS_OFF, /* RX/TX error count >= 256 */
+ CAN_STATE_STOPPED, /* Device is stopped */
+ CAN_STATE_SLEEPING, /* Device is sleeping */
+ CAN_STATE_MAX
+};
+
+/*
+ * CAN bus error counters
+ */
+struct can_berr_counter {
+ __u16 txerr;
+ __u16 rxerr;
+};
+
+/*
+ * CAN controller mode
+ */
+struct can_ctrlmode {
+ __u32 mask;
+ __u32 flags;
+};
+
+#define CAN_CTRLMODE_LOOPBACK 0x01 /* Loopback mode */
+#define CAN_CTRLMODE_LISTENONLY 0x02 /* Listen-only mode */
+#define CAN_CTRLMODE_3_SAMPLES 0x04 /* Triple sampling mode */
+#define CAN_CTRLMODE_ONE_SHOT 0x08 /* One-Shot mode */
+#define CAN_CTRLMODE_BERR_REPORTING 0x10 /* Bus-error reporting */
+
+/*
+ * CAN device statistics
+ */
+struct can_device_stats {
+ __u32 bus_error; /* Bus errors */
+ __u32 error_warning; /* Changes to error warning state */
+ __u32 error_passive; /* Changes to error passive state */
+ __u32 bus_off; /* Changes to bus off state */
+ __u32 arbitration_lost; /* Arbitration lost errors */
+ __u32 restarts; /* CAN controller re-starts */
+};
+
+/*
+ * CAN netlink interface
+ */
+enum {
+ IFLA_CAN_UNSPEC,
+ IFLA_CAN_BITTIMING,
+ IFLA_CAN_BITTIMING_CONST,
+ IFLA_CAN_CLOCK,
+ IFLA_CAN_STATE,
+ IFLA_CAN_CTRLMODE,
+ IFLA_CAN_RESTART_MS,
+ IFLA_CAN_RESTART,
+ IFLA_CAN_BERR_COUNTER,
+ __IFLA_CAN_MAX
+};
+
+#define IFLA_CAN_MAX (__IFLA_CAN_MAX - 1)
+
+#endif /* CAN_NETLINK_H */