zte's code,first commit
Change-Id: I9a04da59e459a9bc0d67f101f700d9d7dc8d681b
diff --git a/ap/os/linux/linux-3.4.x/arch/arm/mach-at91/board-sam9261ek.c b/ap/os/linux/linux-3.4.x/arch/arm/mach-at91/board-sam9261ek.c
new file mode 100644
index 0000000..065fed3
--- /dev/null
+++ b/ap/os/linux/linux-3.4.x/arch/arm/mach-at91/board-sam9261ek.c
@@ -0,0 +1,625 @@
+/*
+ * linux/arch/arm/mach-at91/board-sam9261ek.c
+ *
+ * Copyright (C) 2005 SAN People
+ * Copyright (C) 2006 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/types.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <linux/spi/at73c213.h>
+#include <linux/clk.h>
+#include <linux/dm9000.h>
+#include <linux/fb.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+
+#include <video/atmel_lcdc.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
+#include <mach/system_rev.h>
+
+#include "sam9_smc.h"
+#include "generic.h"
+
+
+static void __init ek_init_early(void)
+{
+ /* Initialize processor: 18.432 MHz crystal */
+ at91_initialize(18432000);
+
+ /* Setup the LEDs */
+ at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
+
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
+}
+
+/*
+ * DM9000 ethernet device
+ */
+#if defined(CONFIG_DM9000)
+static struct resource dm9000_resource[] = {
+ [0] = {
+ .start = AT91_CHIPSELECT_2,
+ .end = AT91_CHIPSELECT_2 + 3,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = AT91_CHIPSELECT_2 + 0x44,
+ .end = AT91_CHIPSELECT_2 + 0xFF,
+ .flags = IORESOURCE_MEM
+ },
+ [2] = {
+ .flags = IORESOURCE_IRQ
+ | IORESOURCE_IRQ_LOWEDGE | IORESOURCE_IRQ_HIGHEDGE,
+ }
+};
+
+static struct dm9000_plat_data dm9000_platdata = {
+ .flags = DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM,
+};
+
+static struct platform_device dm9000_device = {
+ .name = "dm9000",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(dm9000_resource),
+ .resource = dm9000_resource,
+ .dev = {
+ .platform_data = &dm9000_platdata,
+ }
+};
+
+/*
+ * SMC timings for the DM9000.
+ * Note: These timings were calculated for MASTER_CLOCK = 100000000 according to the DM9000 timings.
+ */
+static struct sam9_smc_config __initdata dm9000_smc_config = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 2,
+ .ncs_write_setup = 0,
+ .nwe_setup = 2,
+
+ .ncs_read_pulse = 8,
+ .nrd_pulse = 4,
+ .ncs_write_pulse = 8,
+ .nwe_pulse = 4,
+
+ .read_cycle = 16,
+ .write_cycle = 16,
+
+ .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16,
+ .tdf_cycles = 1,
+};
+
+static void __init ek_add_device_dm9000(void)
+{
+ struct resource *r = &dm9000_resource[2];
+
+ /* Configure chip-select 2 (DM9000) */
+ sam9_smc_configure(0, 2, &dm9000_smc_config);
+
+ /* Configure Reset signal as output */
+ at91_set_gpio_output(AT91_PIN_PC10, 0);
+
+ /* Configure Interrupt pin as input, no pull-up */
+ at91_set_gpio_input(AT91_PIN_PC11, 0);
+
+ r->start = r->end = gpio_to_irq(AT91_PIN_PC11);
+ platform_device_register(&dm9000_device);
+}
+#else
+static void __init ek_add_device_dm9000(void) {}
+#endif /* CONFIG_DM9000 */
+
+
+/*
+ * USB Host Port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+ .ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
+};
+
+
+/*
+ * USB Device Port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+ .vbus_pin = AT91_PIN_PB29,
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+ {
+ .name = "Partition 1",
+ .offset = 0,
+ .size = SZ_256K,
+ },
+ {
+ .name = "Partition 2",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct atmel_nand_data __initdata ek_nand_data = {
+ .ale = 22,
+ .cle = 21,
+ .det_pin = -EINVAL,
+ .rdy_pin = AT91_PIN_PC15,
+ .enable_pin = AT91_PIN_PC14,
+ .ecc_mode = NAND_ECC_SOFT,
+ .on_flash_bbt = 1,
+ .parts = ek_nand_partition,
+ .num_parts = ARRAY_SIZE(ek_nand_partition),
+};
+
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 1,
+ .ncs_write_setup = 0,
+ .nwe_setup = 1,
+
+ .ncs_read_pulse = 3,
+ .nrd_pulse = 3,
+ .ncs_write_pulse = 3,
+ .nwe_pulse = 3,
+
+ .read_cycle = 5,
+ .write_cycle = 5,
+
+ .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+ .tdf_cycles = 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+ ek_nand_data.bus_width_16 = board_have_nand_16bit();
+ /* setup bus-width (8 or 16) */
+ if (ek_nand_data.bus_width_16)
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+ else
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+ /* configure chip-select 3 (NAND) */
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
+
+ at91_add_device_nand(&ek_nand_data);
+}
+
+/*
+ * SPI related devices
+ */
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+
+/*
+ * ADS7846 Touchscreen
+ */
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+
+static int ads7843_pendown_state(void)
+{
+ return !at91_get_gpio_value(AT91_PIN_PC2); /* Touchscreen PENIRQ */
+}
+
+static struct ads7846_platform_data ads_info = {
+ .model = 7843,
+ .x_min = 150,
+ .x_max = 3830,
+ .y_min = 190,
+ .y_max = 3830,
+ .vref_delay_usecs = 100,
+ .x_plate_ohms = 450,
+ .y_plate_ohms = 250,
+ .pressure_max = 15000,
+ .debounce_max = 1,
+ .debounce_rep = 0,
+ .debounce_tol = (~0),
+ .get_pendown_state = ads7843_pendown_state,
+};
+
+static void __init ek_add_device_ts(void)
+{
+ at91_set_B_periph(AT91_PIN_PC2, 1); /* External IRQ0, with pullup */
+ at91_set_gpio_input(AT91_PIN_PA11, 1); /* Touchscreen BUSY signal */
+}
+#else
+static void __init ek_add_device_ts(void) {}
+#endif
+
+/*
+ * Audio
+ */
+static struct at73c213_board_info at73c213_data = {
+ .ssc_id = 1,
+#if defined(CONFIG_MACH_AT91SAM9261EK)
+ .shortname = "AT91SAM9261-EK external DAC",
+#else
+ .shortname = "AT91SAM9G10-EK external DAC",
+#endif
+};
+
+#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
+static void __init at73c213_set_clk(struct at73c213_board_info *info)
+{
+ struct clk *pck2;
+ struct clk *plla;
+
+ pck2 = clk_get(NULL, "pck2");
+ plla = clk_get(NULL, "plla");
+
+ /* AT73C213 MCK Clock */
+ at91_set_B_periph(AT91_PIN_PB31, 0); /* PCK2 */
+
+ clk_set_parent(pck2, plla);
+ clk_put(plla);
+
+ info->dac_clk = pck2;
+}
+#else
+static void __init at73c213_set_clk(struct at73c213_board_info *info) {}
+#endif
+
+/*
+ * SPI devices
+ */
+static struct spi_board_info ek_spi_devices[] = {
+ { /* DataFlash chip */
+ .modalias = "mtd_dataflash",
+ .chip_select = 0,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+ {
+ .modalias = "ads7846",
+ .chip_select = 2,
+ .max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */
+ .bus_num = 0,
+ .platform_data = &ads_info,
+ .irq = AT91SAM9261_ID_IRQ0,
+ .controller_data = (void *) AT91_PIN_PA28, /* CS pin */
+ },
+#endif
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+ { /* DataFlash card - jumper (J12) configurable to CS3 or CS0 */
+ .modalias = "mtd_dataflash",
+ .chip_select = 3,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#elif defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
+ { /* AT73C213 DAC */
+ .modalias = "at73c213",
+ .chip_select = 3,
+ .max_speed_hz = 10 * 1000 * 1000,
+ .bus_num = 0,
+ .mode = SPI_MODE_1,
+ .platform_data = &at73c213_data,
+ .controller_data = (void*) AT91_PIN_PA29, /* default for CS3 is PA6, but it must be PA29 */
+ },
+#endif
+};
+
+#else /* CONFIG_SPI_ATMEL_* */
+/* spi0 and mmc/sd share the same PIO pins: cannot be used at the same time */
+
+/*
+ * MCI (SD/MMC)
+ * det_pin, wp_pin and vcc_pin are not connected
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+ .wire4 = 1,
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
+};
+
+#endif /* CONFIG_SPI_ATMEL_* */
+
+
+/*
+ * LCD Controller
+ */
+#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
+
+#if defined(CONFIG_FB_ATMEL_STN)
+
+/* STN */
+static struct fb_videomode at91_stn_modes[] = {
+ {
+ .name = "SP06Q002 @ 75",
+ .refresh = 75,
+ .xres = 320, .yres = 240,
+ .pixclock = KHZ2PICOS(1440),
+
+ .left_margin = 1, .right_margin = 1,
+ .upper_margin = 0, .lower_margin = 0,
+ .hsync_len = 1, .vsync_len = 1,
+
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+};
+
+static struct fb_monspecs at91fb_default_stn_monspecs = {
+ .manufacturer = "HIT",
+ .monitor = "SP06Q002",
+
+ .modedb = at91_stn_modes,
+ .modedb_len = ARRAY_SIZE(at91_stn_modes),
+ .hfmin = 15000,
+ .hfmax = 64000,
+ .vfmin = 50,
+ .vfmax = 150,
+};
+
+#define AT91SAM9261_DEFAULT_STN_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
+ | ATMEL_LCDC_DISTYPE_STNMONO \
+ | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE \
+ | ATMEL_LCDC_IFWIDTH_4 \
+ | ATMEL_LCDC_SCANMOD_SINGLE)
+
+static void at91_lcdc_stn_power_control(int on)
+{
+ /* backlight */
+ if (on) { /* power up */
+ at91_set_gpio_value(AT91_PIN_PC14, 0);
+ at91_set_gpio_value(AT91_PIN_PC15, 0);
+ } else { /* power down */
+ at91_set_gpio_value(AT91_PIN_PC14, 1);
+ at91_set_gpio_value(AT91_PIN_PC15, 1);
+ }
+}
+
+static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+ .default_bpp = 1,
+ .default_dmacon = ATMEL_LCDC_DMAEN,
+ .default_lcdcon2 = AT91SAM9261_DEFAULT_STN_LCDCON2,
+ .default_monspecs = &at91fb_default_stn_monspecs,
+ .atmel_lcdfb_power_control = at91_lcdc_stn_power_control,
+ .guard_time = 1,
+#if defined(CONFIG_MACH_AT91SAM9G10EK)
+ .lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB,
+#endif
+};
+
+#else
+
+/* TFT */
+static struct fb_videomode at91_tft_vga_modes[] = {
+ {
+ .name = "TX09D50VM1CCA @ 60",
+ .refresh = 60,
+ .xres = 240, .yres = 320,
+ .pixclock = KHZ2PICOS(4965),
+
+ .left_margin = 1, .right_margin = 33,
+ .upper_margin = 1, .lower_margin = 0,
+ .hsync_len = 5, .vsync_len = 1,
+
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+};
+
+static struct fb_monspecs at91fb_default_tft_monspecs = {
+ .manufacturer = "HIT",
+ .monitor = "TX09D50VM1CCA",
+
+ .modedb = at91_tft_vga_modes,
+ .modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
+ .hfmin = 15000,
+ .hfmax = 64000,
+ .vfmin = 50,
+ .vfmax = 150,
+};
+
+#define AT91SAM9261_DEFAULT_TFT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
+ | ATMEL_LCDC_DISTYPE_TFT \
+ | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
+
+static void at91_lcdc_tft_power_control(int on)
+{
+ if (on)
+ at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
+ else
+ at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
+}
+
+static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+ .lcdcon_is_backlight = true,
+ .default_bpp = 16,
+ .default_dmacon = ATMEL_LCDC_DMAEN,
+ .default_lcdcon2 = AT91SAM9261_DEFAULT_TFT_LCDCON2,
+ .default_monspecs = &at91fb_default_tft_monspecs,
+ .atmel_lcdfb_power_control = at91_lcdc_tft_power_control,
+ .guard_time = 1,
+#if defined(CONFIG_MACH_AT91SAM9G10EK)
+ .lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB,
+#endif
+};
+#endif
+
+#else
+static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+#endif
+
+
+/*
+ * GPIO Buttons
+ */
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button ek_buttons[] = {
+ {
+ .gpio = AT91_PIN_PA27,
+ .code = BTN_0,
+ .desc = "Button 0",
+ .active_low = 1,
+ .wakeup = 1,
+ },
+ {
+ .gpio = AT91_PIN_PA26,
+ .code = BTN_1,
+ .desc = "Button 1",
+ .active_low = 1,
+ .wakeup = 1,
+ },
+ {
+ .gpio = AT91_PIN_PA25,
+ .code = BTN_2,
+ .desc = "Button 2",
+ .active_low = 1,
+ .wakeup = 1,
+ },
+ {
+ .gpio = AT91_PIN_PA24,
+ .code = BTN_3,
+ .desc = "Button 3",
+ .active_low = 1,
+ .wakeup = 1,
+ }
+};
+
+static struct gpio_keys_platform_data ek_button_data = {
+ .buttons = ek_buttons,
+ .nbuttons = ARRAY_SIZE(ek_buttons),
+};
+
+static struct platform_device ek_button_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &ek_button_data,
+ }
+};
+
+static void __init ek_add_device_buttons(void)
+{
+ at91_set_gpio_input(AT91_PIN_PA27, 1); /* btn0 */
+ at91_set_deglitch(AT91_PIN_PA27, 1);
+ at91_set_gpio_input(AT91_PIN_PA26, 1); /* btn1 */
+ at91_set_deglitch(AT91_PIN_PA26, 1);
+ at91_set_gpio_input(AT91_PIN_PA25, 1); /* btn2 */
+ at91_set_deglitch(AT91_PIN_PA25, 1);
+ at91_set_gpio_input(AT91_PIN_PA24, 1); /* btn3 */
+ at91_set_deglitch(AT91_PIN_PA24, 1);
+
+ platform_device_register(&ek_button_device);
+}
+#else
+static void __init ek_add_device_buttons(void) {}
+#endif
+
+/*
+ * LEDs
+ */
+static struct gpio_led ek_leds[] = {
+ { /* "bottom" led, green, userled1 to be defined */
+ .name = "ds7",
+ .gpio = AT91_PIN_PA14,
+ .active_low = 1,
+ .default_trigger = "none",
+ },
+ { /* "top" led, green, userled2 to be defined */
+ .name = "ds8",
+ .gpio = AT91_PIN_PA13,
+ .active_low = 1,
+ .default_trigger = "none",
+ },
+ { /* "power" led, yellow */
+ .name = "ds1",
+ .gpio = AT91_PIN_PA23,
+ .default_trigger = "heartbeat",
+ }
+};
+
+static void __init ek_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* USB Host */
+ at91_add_device_usbh(&ek_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&ek_udc_data);
+ /* I2C */
+ at91_add_device_i2c(NULL, 0);
+ /* NAND */
+ ek_add_device_nand();
+ /* DM9000 ethernet */
+ ek_add_device_dm9000();
+
+ /* spi0 and mmc/sd share the same PIO pins */
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+ /* SPI */
+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+ /* Touchscreen */
+ ek_add_device_ts();
+ /* SSC (to AT73C213) */
+ at73c213_set_clk(&at73c213_data);
+ at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
+#else
+ /* MMC */
+ at91_add_device_mmc(0, &ek_mmc_data);
+#endif
+ /* LCD Controller */
+ at91_add_device_lcdc(&ek_lcdc_data);
+ /* Push Buttons */
+ ek_add_device_buttons();
+ /* LEDs */
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+}
+
+#if defined(CONFIG_MACH_AT91SAM9261EK)
+MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK")
+#else
+MACHINE_START(AT91SAM9G10EK, "Atmel AT91SAM9G10-EK")
+#endif
+ /* Maintainer: Atmel */
+ .timer = &at91sam926x_timer,
+ .map_io = at91_map_io,
+ .init_early = ek_init_early,
+ .init_irq = at91_init_irq_default,
+ .init_machine = ek_board_init,
+MACHINE_END