zte's code,first commit
Change-Id: I9a04da59e459a9bc0d67f101f700d9d7dc8d681b
diff --git a/ap/os/linux/linux-3.4.x/arch/arm/mach-at91/board-sam9263ek.c b/ap/os/linux/linux-3.4.x/arch/arm/mach-at91/board-sam9263ek.c
new file mode 100644
index 0000000..2ffe50f
--- /dev/null
+++ b/ap/os/linux/linux-3.4.x/arch/arm/mach-at91/board-sam9263ek.c
@@ -0,0 +1,453 @@
+/*
+ * linux/arch/arm/mach-at91/board-sam9263ek.c
+ *
+ * Copyright (C) 2005 SAN People
+ * Copyright (C) 2007 Atmel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/types.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <linux/i2c/at24.h>
+#include <linux/fb.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/leds.h>
+
+#include <video/atmel_lcdc.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
+#include <mach/system_rev.h>
+
+#include "sam9_smc.h"
+#include "generic.h"
+
+
+static void __init ek_init_early(void)
+{
+ /* Initialize processor: 16.367 MHz crystal */
+ at91_initialize(16367660);
+
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
+}
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+ .ports = 2,
+ .vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
+ .vbus_pin_active_low = {1, 1},
+ .overcurrent_pin= {-EINVAL, -EINVAL},
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+ .vbus_pin = AT91_PIN_PA25,
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
+};
+
+
+/*
+ * ADS7846 Touchscreen
+ */
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+static int ads7843_pendown_state(void)
+{
+ return !at91_get_gpio_value(AT91_PIN_PA15); /* Touchscreen PENIRQ */
+}
+
+static struct ads7846_platform_data ads_info = {
+ .model = 7843,
+ .x_min = 150,
+ .x_max = 3830,
+ .y_min = 190,
+ .y_max = 3830,
+ .vref_delay_usecs = 100,
+ .x_plate_ohms = 450,
+ .y_plate_ohms = 250,
+ .pressure_max = 15000,
+ .debounce_max = 1,
+ .debounce_rep = 0,
+ .debounce_tol = (~0),
+ .get_pendown_state = ads7843_pendown_state,
+};
+
+static void __init ek_add_device_ts(void)
+{
+ at91_set_B_periph(AT91_PIN_PA15, 1); /* External IRQ1, with pullup */
+ at91_set_gpio_input(AT91_PIN_PA31, 1); /* Touchscreen BUSY signal */
+}
+#else
+static void __init ek_add_device_ts(void) {}
+#endif
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+ { /* DataFlash card */
+ .modalias = "mtd_dataflash",
+ .chip_select = 0,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#endif
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+ {
+ .modalias = "ads7846",
+ .chip_select = 3,
+ .max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */
+ .bus_num = 0,
+ .platform_data = &ads_info,
+ .irq = AT91SAM9263_ID_IRQ1,
+ },
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+ .wire4 = 1,
+ .det_pin = AT91_PIN_PE18,
+ .wp_pin = AT91_PIN_PE19,
+ .vcc_pin = -EINVAL,
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct macb_platform_data __initdata ek_macb_data = {
+ .phy_irq_pin = AT91_PIN_PE31,
+ .is_rmii = 1,
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+ {
+ .name = "Partition 1",
+ .offset = 0,
+ .size = SZ_64M,
+ },
+ {
+ .name = "Partition 2",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct atmel_nand_data __initdata ek_nand_data = {
+ .ale = 21,
+ .cle = 22,
+ .det_pin = -EINVAL,
+ .rdy_pin = AT91_PIN_PA22,
+ .enable_pin = AT91_PIN_PD15,
+ .ecc_mode = NAND_ECC_SOFT,
+ .on_flash_bbt = 1,
+ .parts = ek_nand_partition,
+ .num_parts = ARRAY_SIZE(ek_nand_partition),
+};
+
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 1,
+ .ncs_write_setup = 0,
+ .nwe_setup = 1,
+
+ .ncs_read_pulse = 3,
+ .nrd_pulse = 3,
+ .ncs_write_pulse = 3,
+ .nwe_pulse = 3,
+
+ .read_cycle = 5,
+ .write_cycle = 5,
+
+ .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+ .tdf_cycles = 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+ ek_nand_data.bus_width_16 = board_have_nand_16bit();
+ /* setup bus-width (8 or 16) */
+ if (ek_nand_data.bus_width_16)
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+ else
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+ /* configure chip-select 3 (NAND) */
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
+
+ at91_add_device_nand(&ek_nand_data);
+}
+
+
+/*
+ * I2C devices
+ */
+static struct at24_platform_data at24c512 = {
+ .byte_len = SZ_512K / 8,
+ .page_size = 128,
+ .flags = AT24_FLAG_ADDR16,
+};
+
+
+static struct i2c_board_info __initdata ek_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("24c512", 0x50),
+ .platform_data = &at24c512,
+ },
+ /* more devices can be added using expansion connectors */
+};
+
+/*
+ * LCD Controller
+ */
+#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
+static struct fb_videomode at91_tft_vga_modes[] = {
+ {
+ .name = "TX09D50VM1CCA @ 60",
+ .refresh = 60,
+ .xres = 240, .yres = 320,
+ .pixclock = KHZ2PICOS(4965),
+
+ .left_margin = 1, .right_margin = 33,
+ .upper_margin = 1, .lower_margin = 0,
+ .hsync_len = 5, .vsync_len = 1,
+
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+};
+
+static struct fb_monspecs at91fb_default_monspecs = {
+ .manufacturer = "HIT",
+ .monitor = "TX09D70VM1CCA",
+
+ .modedb = at91_tft_vga_modes,
+ .modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
+ .hfmin = 15000,
+ .hfmax = 64000,
+ .vfmin = 50,
+ .vfmax = 150,
+};
+
+#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
+ | ATMEL_LCDC_DISTYPE_TFT \
+ | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
+
+static void at91_lcdc_power_control(int on)
+{
+ at91_set_gpio_value(AT91_PIN_PA30, on);
+}
+
+/* Driver datas */
+static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+ .lcdcon_is_backlight = true,
+ .default_bpp = 16,
+ .default_dmacon = ATMEL_LCDC_DMAEN,
+ .default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2,
+ .default_monspecs = &at91fb_default_monspecs,
+ .atmel_lcdfb_power_control = at91_lcdc_power_control,
+ .guard_time = 1,
+};
+
+#else
+static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+#endif
+
+
+/*
+ * GPIO Buttons
+ */
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button ek_buttons[] = {
+ { /* BP1, "leftclic" */
+ .code = BTN_LEFT,
+ .gpio = AT91_PIN_PC5,
+ .active_low = 1,
+ .desc = "left_click",
+ .wakeup = 1,
+ },
+ { /* BP2, "rightclic" */
+ .code = BTN_RIGHT,
+ .gpio = AT91_PIN_PC4,
+ .active_low = 1,
+ .desc = "right_click",
+ .wakeup = 1,
+ }
+};
+
+static struct gpio_keys_platform_data ek_button_data = {
+ .buttons = ek_buttons,
+ .nbuttons = ARRAY_SIZE(ek_buttons),
+};
+
+static struct platform_device ek_button_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &ek_button_data,
+ }
+};
+
+static void __init ek_add_device_buttons(void)
+{
+ at91_set_GPIO_periph(AT91_PIN_PC5, 1); /* left button */
+ at91_set_deglitch(AT91_PIN_PC5, 1);
+ at91_set_GPIO_periph(AT91_PIN_PC4, 1); /* right button */
+ at91_set_deglitch(AT91_PIN_PC4, 1);
+
+ platform_device_register(&ek_button_device);
+}
+#else
+static void __init ek_add_device_buttons(void) {}
+#endif
+
+
+/*
+ * AC97
+ * reset_pin is not connected: NRST
+ */
+static struct ac97c_platform_data ek_ac97_data = {
+ .reset_pin = -EINVAL,
+};
+
+
+/*
+ * LEDs ... these could all be PWM-driven, for variable brightness
+ */
+static struct gpio_led ek_leds[] = {
+ { /* "right" led, green, userled2 (could be driven by pwm2) */
+ .name = "ds2",
+ .gpio = AT91_PIN_PC29,
+ .active_low = 1,
+ .default_trigger = "nand-disk",
+ },
+ { /* "power" led, yellow (could be driven by pwm0) */
+ .name = "ds3",
+ .gpio = AT91_PIN_PB7,
+ .default_trigger = "heartbeat",
+ }
+};
+
+/*
+ * PWM Leds
+ */
+static struct gpio_led ek_pwm_led[] = {
+ /* For now only DS1 is PWM-driven (by pwm1) */
+ {
+ .name = "ds1",
+ .gpio = 1, /* is PWM channel number */
+ .active_low = 1,
+ .default_trigger = "none",
+ }
+};
+
+/*
+ * CAN
+ */
+static void sam9263ek_transceiver_switch(int on)
+{
+ if (on) {
+ at91_set_gpio_output(AT91_PIN_PA18, 1); /* CANRXEN */
+ at91_set_gpio_output(AT91_PIN_PA19, 0); /* CANRS */
+ } else {
+ at91_set_gpio_output(AT91_PIN_PA18, 0); /* CANRXEN */
+ at91_set_gpio_output(AT91_PIN_PA19, 1); /* CANRS */
+ }
+}
+
+static struct at91_can_data ek_can_data = {
+ .transceiver_switch = sam9263ek_transceiver_switch,
+};
+
+static void __init ek_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* USB Host */
+ at91_add_device_usbh(&ek_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&ek_udc_data);
+ /* SPI */
+ at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */
+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+ /* Touchscreen */
+ ek_add_device_ts();
+ /* MMC */
+ at91_add_device_mmc(1, &ek_mmc_data);
+ /* Ethernet */
+ at91_add_device_eth(&ek_macb_data);
+ /* NAND */
+ ek_add_device_nand();
+ /* I2C */
+ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
+ /* LCD Controller */
+ at91_add_device_lcdc(&ek_lcdc_data);
+ /* Push Buttons */
+ ek_add_device_buttons();
+ /* AC97 */
+ at91_add_device_ac97(&ek_ac97_data);
+ /* LEDs */
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+ at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
+ /* CAN */
+ at91_add_device_can(&ek_can_data);
+}
+
+MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
+ /* Maintainer: Atmel */
+ .timer = &at91sam926x_timer,
+ .map_io = at91_map_io,
+ .init_early = ek_init_early,
+ .init_irq = at91_init_irq_default,
+ .init_machine = ek_board_init,
+MACHINE_END