zte's code,first commit
Change-Id: I9a04da59e459a9bc0d67f101f700d9d7dc8d681b
diff --git a/ap/os/linux/linux-3.4.x/arch/arm/mach-omap2/board-omap3stalker.c b/ap/os/linux/linux-3.4.x/arch/arm/mach-omap2/board-omap3stalker.c
new file mode 100644
index 0000000..4dffc95
--- /dev/null
+++ b/ap/os/linux/linux-3.4.x/arch/arm/mach-omap2/board-omap3stalker.c
@@ -0,0 +1,462 @@
+/*
+ * linux/arch/arm/mach-omap2/board-omap3evm.c
+ *
+ * Copyright (C) 2008 Guangzhou EMA-Tech
+ *
+ * Modified from mach-omap2/board-omap3evm.c
+ *
+ * Initial code: Syed Mohammed Khasim
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
+#include <linux/i2c/twl.h>
+#include <linux/mmc/host.h>
+
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/flash.h>
+
+#include <plat/board.h>
+#include "common.h"
+#include <plat/gpmc.h>
+#include <plat/nand.h>
+#include <plat/usb.h>
+#include <video/omapdss.h>
+#include <video/omap-panel-generic-dpi.h>
+#include <video/omap-panel-dvi.h>
+
+#include <plat/mcspi.h>
+#include <linux/input/matrix_keypad.h>
+#include <linux/spi/spi.h>
+#include <linux/interrupt.h>
+#include <linux/smsc911x.h>
+#include <linux/i2c/at24.h>
+
+#include "sdram-micron-mt46h32m32lf-6.h"
+#include "mux.h"
+#include "hsmmc.h"
+#include "common-board-devices.h"
+
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <plat/gpmc-smsc911x.h>
+
+#define OMAP3STALKER_ETHR_START 0x2c000000
+#define OMAP3STALKER_ETHR_SIZE 1024
+#define OMAP3STALKER_ETHR_GPIO_IRQ 19
+#define OMAP3STALKER_SMC911X_CS 5
+
+static struct omap_smsc911x_platform_data smsc911x_cfg = {
+ .cs = OMAP3STALKER_SMC911X_CS,
+ .gpio_irq = OMAP3STALKER_ETHR_GPIO_IRQ,
+ .gpio_reset = -EINVAL,
+ .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
+};
+
+static inline void __init omap3stalker_init_eth(void)
+{
+ omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
+ gpmc_smsc911x_init(&smsc911x_cfg);
+}
+
+#else
+static inline void __init omap3stalker_init_eth(void)
+{
+ return;
+}
+#endif
+
+/*
+ * OMAP3 DSS control signals
+ */
+
+#define DSS_ENABLE_GPIO 199
+#define LCD_PANEL_BKLIGHT_GPIO 210
+#define ENABLE_VPLL2_DEV_GRP 0xE0
+
+static int lcd_enabled;
+static int dvi_enabled;
+
+static void __init omap3_stalker_display_init(void)
+{
+ return;
+}
+
+static int omap3_stalker_enable_tv(struct omap_dss_device *dssdev)
+{
+ return 0;
+}
+
+static void omap3_stalker_disable_tv(struct omap_dss_device *dssdev)
+{
+}
+
+static struct omap_dss_device omap3_stalker_tv_device = {
+ .name = "tv",
+ .driver_name = "venc",
+ .type = OMAP_DISPLAY_TYPE_VENC,
+#if defined(CONFIG_OMAP2_VENC_OUT_TYPE_SVIDEO)
+ .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
+#elif defined(CONFIG_OMAP2_VENC_OUT_TYPE_COMPOSITE)
+ .u.venc.type = OMAP_DSS_VENC_TYPE_COMPOSITE,
+#endif
+ .platform_enable = omap3_stalker_enable_tv,
+ .platform_disable = omap3_stalker_disable_tv,
+};
+
+static int omap3_stalker_enable_dvi(struct omap_dss_device *dssdev)
+{
+ if (lcd_enabled) {
+ printk(KERN_ERR "cannot enable DVI, LCD is enabled\n");
+ return -EINVAL;
+ }
+ gpio_set_value(DSS_ENABLE_GPIO, 1);
+ dvi_enabled = 1;
+ return 0;
+}
+
+static void omap3_stalker_disable_dvi(struct omap_dss_device *dssdev)
+{
+ gpio_set_value(DSS_ENABLE_GPIO, 0);
+ dvi_enabled = 0;
+}
+
+static struct panel_dvi_platform_data dvi_panel = {
+ .platform_enable = omap3_stalker_enable_dvi,
+ .platform_disable = omap3_stalker_disable_dvi,
+};
+
+static struct omap_dss_device omap3_stalker_dvi_device = {
+ .name = "dvi",
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .driver_name = "dvi",
+ .data = &dvi_panel,
+ .phy.dpi.data_lines = 24,
+};
+
+static struct omap_dss_device *omap3_stalker_dss_devices[] = {
+ &omap3_stalker_tv_device,
+ &omap3_stalker_dvi_device,
+};
+
+static struct omap_dss_board_info omap3_stalker_dss_data = {
+ .num_devices = ARRAY_SIZE(omap3_stalker_dss_devices),
+ .devices = omap3_stalker_dss_devices,
+ .default_device = &omap3_stalker_dvi_device,
+};
+
+static struct regulator_consumer_supply omap3stalker_vmmc1_supply[] = {
+ REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
+};
+
+static struct regulator_consumer_supply omap3stalker_vsim_supply[] = {
+ REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
+};
+
+/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+static struct regulator_init_data omap3stalker_vmmc1 = {
+ .constraints = {
+ .min_uV = 1850000,
+ .max_uV = 3150000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vmmc1_supply),
+ .consumer_supplies = omap3stalker_vmmc1_supply,
+};
+
+/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
+static struct regulator_init_data omap3stalker_vsim = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 3000000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vsim_supply),
+ .consumer_supplies = omap3stalker_vsim_supply,
+};
+
+static struct omap2_hsmmc_info mmc[] = {
+ {
+ .mmc = 1,
+ .caps = MMC_CAP_4_BIT_DATA,
+ .gpio_cd = -EINVAL,
+ .gpio_wp = 23,
+ .deferred = true,
+ },
+ {} /* Terminator */
+};
+
+static struct gpio_keys_button gpio_buttons[] = {
+ {
+ .code = BTN_EXTRA,
+ .gpio = 18,
+ .desc = "user",
+ .wakeup = 1,
+ },
+};
+
+static struct gpio_keys_platform_data gpio_key_info = {
+ .buttons = gpio_buttons,
+ .nbuttons = ARRAY_SIZE(gpio_buttons),
+};
+
+static struct platform_device keys_gpio = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_key_info,
+ },
+};
+
+static struct gpio_led gpio_leds[] = {
+ {
+ .name = "stalker:D8:usr0",
+ .default_trigger = "default-on",
+ .gpio = 126,
+ },
+ {
+ .name = "stalker:D9:usr1",
+ .default_trigger = "default-on",
+ .gpio = 127,
+ },
+ {
+ .name = "stalker:D3:mmc0",
+ .gpio = -EINVAL, /* gets replaced */
+ .active_low = true,
+ .default_trigger = "mmc0",
+ },
+ {
+ .name = "stalker:D4:heartbeat",
+ .gpio = -EINVAL, /* gets replaced */
+ .active_low = true,
+ .default_trigger = "heartbeat",
+ },
+};
+
+static struct gpio_led_platform_data gpio_led_info = {
+ .leds = gpio_leds,
+ .num_leds = ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device leds_gpio = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_led_info,
+ },
+};
+
+static int
+omap3stalker_twl_gpio_setup(struct device *dev,
+ unsigned gpio, unsigned ngpio)
+{
+ /* gpio + 0 is "mmc0_cd" (input/IRQ) */
+ mmc[0].gpio_cd = gpio + 0;
+ omap_hsmmc_late_init(mmc);
+
+ /*
+ * Most GPIOs are for USB OTG. Some are mostly sent to
+ * the P2 connector; notably LEDA for the LCD backlight.
+ */
+
+ /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
+ gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
+ "EN_LCD_BKL");
+
+ /* gpio + 7 == DVI Enable */
+ gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
+
+ /* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
+ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+ /* GPIO + 13 == ledsync (out, heartbeat) */
+ gpio_leds[3].gpio = gpio + 13;
+
+ platform_device_register(&leds_gpio);
+ return 0;
+}
+
+static struct twl4030_gpio_platform_data omap3stalker_gpio_data = {
+ .gpio_base = OMAP_MAX_GPIO_LINES,
+ .irq_base = TWL4030_GPIO_IRQ_BASE,
+ .irq_end = TWL4030_GPIO_IRQ_END,
+ .use_leds = true,
+ .setup = omap3stalker_twl_gpio_setup,
+};
+
+static uint32_t board_keymap[] = {
+ KEY(0, 0, KEY_LEFT),
+ KEY(0, 1, KEY_DOWN),
+ KEY(0, 2, KEY_ENTER),
+ KEY(0, 3, KEY_M),
+
+ KEY(1, 0, KEY_RIGHT),
+ KEY(1, 1, KEY_UP),
+ KEY(1, 2, KEY_I),
+ KEY(1, 3, KEY_N),
+
+ KEY(2, 0, KEY_A),
+ KEY(2, 1, KEY_E),
+ KEY(2, 2, KEY_J),
+ KEY(2, 3, KEY_O),
+
+ KEY(3, 0, KEY_B),
+ KEY(3, 1, KEY_F),
+ KEY(3, 2, KEY_K),
+ KEY(3, 3, KEY_P)
+};
+
+static struct matrix_keymap_data board_map_data = {
+ .keymap = board_keymap,
+ .keymap_size = ARRAY_SIZE(board_keymap),
+};
+
+static struct twl4030_keypad_data omap3stalker_kp_data = {
+ .keymap_data = &board_map_data,
+ .rows = 4,
+ .cols = 4,
+ .rep = 1,
+};
+
+static struct twl4030_platform_data omap3stalker_twldata = {
+ /* platform_data for children goes here */
+ .keypad = &omap3stalker_kp_data,
+ .gpio = &omap3stalker_gpio_data,
+ .vmmc1 = &omap3stalker_vmmc1,
+ .vsim = &omap3stalker_vsim,
+};
+
+static struct at24_platform_data fram_info = {
+ .byte_len = (64 * 1024) / 8,
+ .page_size = 8192,
+ .flags = AT24_FLAG_ADDR16 | AT24_FLAG_IRUGO,
+};
+
+static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
+ {
+ I2C_BOARD_INFO("24c64", 0x50),
+ .flags = I2C_CLIENT_WAKE,
+ .platform_data = &fram_info,
+ },
+};
+
+static int __init omap3_stalker_i2c_init(void)
+{
+ omap3_pmic_get_config(&omap3stalker_twldata,
+ TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
+ TWL_COMMON_PDATA_AUDIO,
+ TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
+
+ omap3stalker_twldata.vdac->constraints.apply_uV = true;
+ omap3stalker_twldata.vpll2->constraints.apply_uV = true;
+ omap3stalker_twldata.vpll2->constraints.name = "VDVI";
+
+ omap3_pmic_init("twl4030", &omap3stalker_twldata);
+ omap_register_i2c_bus(2, 400, NULL, 0);
+ omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
+ ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
+ return 0;
+}
+
+#define OMAP3_STALKER_TS_GPIO 175
+
+static struct omap_board_config_kernel omap3_stalker_config[] __initdata = {
+};
+
+static struct platform_device *omap3_stalker_devices[] __initdata = {
+ &keys_gpio,
+};
+
+static struct usbhs_omap_board_data usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = 21,
+ .reset_gpio_port[2] = -EINVAL,
+};
+
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux board_mux[] __initdata = {
+ OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
+ OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
+ OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
+ OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
+ {.reg_offset = OMAP_MUX_TERMINATOR},
+};
+#endif
+
+static struct regulator_consumer_supply dummy_supplies[] = {
+ REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
+ REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
+};
+
+static void __init omap3_stalker_init(void)
+{
+ regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+ omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
+ omap_board_config = omap3_stalker_config;
+ omap_board_config_size = ARRAY_SIZE(omap3_stalker_config);
+
+ omap_mux_init_gpio(23, OMAP_PIN_INPUT);
+ omap_hsmmc_init(mmc);
+
+ omap3_stalker_i2c_init();
+
+ platform_add_devices(omap3_stalker_devices,
+ ARRAY_SIZE(omap3_stalker_devices));
+
+ omap_display_init(&omap3_stalker_dss_data);
+
+ omap_serial_init();
+ omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
+ usb_musb_init(NULL);
+ usbhs_init(&usbhs_bdata);
+ omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
+
+ omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
+ omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
+
+ omap3stalker_init_eth();
+ omap3_stalker_display_init();
+/* Ensure SDRC pins are mux'd for self-refresh */
+ omap_mux_init_signal("sdr_cke0", OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("sdr_cke1", OMAP_PIN_OUTPUT);
+}
+
+MACHINE_START(SBC3530, "OMAP3 STALKER")
+ /* Maintainer: Jason Lam -lzg@ema-tech.com */
+ .atag_offset = 0x100,
+ .map_io = omap3_map_io,
+ .init_early = omap35xx_init_early,
+ .init_irq = omap3_init_irq,
+ .handle_irq = omap3_intc_handle_irq,
+ .init_machine = omap3_stalker_init,
+ .timer = &omap3_secure_timer,
+ .restart = omap_prcm_restart,
+MACHINE_END