zte's code,first commit
Change-Id: I9a04da59e459a9bc0d67f101f700d9d7dc8d681b
diff --git a/ap/os/linux/linux-3.4.x/arch/arm/mach-omap2/prcm.c b/ap/os/linux/linux-3.4.x/arch/arm/mach-omap2/prcm.c
new file mode 100644
index 0000000..626acfa
--- /dev/null
+++ b/ap/os/linux/linux-3.4.x/arch/arm/mach-omap2/prcm.c
@@ -0,0 +1,158 @@
+/*
+ * linux/arch/arm/mach-omap2/prcm.c
+ *
+ * OMAP 24xx Power Reset and Clock Management (PRCM) functions
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ *
+ * Written by Tony Lindgren <tony.lindgren@nokia.com>
+ *
+ * Copyright (C) 2007 Texas Instruments, Inc.
+ * Rajendra Nayak <rnayak@ti.com>
+ *
+ * Some pieces of code Copyright (C) 2005 Texas Instruments, Inc.
+ * Upgraded with OMAP4 support by Abhijit Pagare <abhijitpagare@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/export.h>
+
+#include "common.h"
+#include <plat/prcm.h>
+#include <plat/irqs.h>
+
+#include "clock.h"
+#include "clock2xxx.h"
+#include "cm2xxx_3xxx.h"
+#include "prm2xxx_3xxx.h"
+#include "prm44xx.h"
+#include "prminst44xx.h"
+#include "prm-regbits-24xx.h"
+#include "prm-regbits-44xx.h"
+#include "control.h"
+
+void __iomem *prm_base;
+void __iomem *cm_base;
+void __iomem *cm2_base;
+
+#define MAX_MODULE_ENABLE_WAIT 100000
+
+u32 omap_prcm_get_reset_sources(void)
+{
+ /* XXX This presumably needs modification for 34XX */
+ if (cpu_is_omap24xx() || cpu_is_omap34xx())
+ return omap2_prm_read_mod_reg(WKUP_MOD, OMAP2_RM_RSTST) & 0x7f;
+ if (cpu_is_omap44xx())
+ return omap2_prm_read_mod_reg(WKUP_MOD, OMAP4_RM_RSTST) & 0x7f;
+
+ return 0;
+}
+EXPORT_SYMBOL(omap_prcm_get_reset_sources);
+
+/* Resets clock rates and reboots the system. Only called from system.h */
+void omap_prcm_restart(char mode, const char *cmd)
+{
+ s16 prcm_offs = 0;
+
+ if (cpu_is_omap24xx()) {
+ omap2xxx_clk_prepare_for_reboot();
+
+ prcm_offs = WKUP_MOD;
+ } else if (cpu_is_omap34xx()) {
+ prcm_offs = OMAP3430_GR_MOD;
+ omap3_ctrl_write_boot_mode((cmd ? (u8)*cmd : 0));
+ } else if (cpu_is_omap44xx()) {
+ omap4_prminst_global_warm_sw_reset(); /* never returns */
+ } else {
+ WARN_ON(1);
+ }
+
+ /*
+ * As per Errata i520, in some cases, user will not be able to
+ * access DDR memory after warm-reset.
+ * This situation occurs while the warm-reset happens during a read
+ * access to DDR memory. In that particular condition, DDR memory
+ * does not respond to a corrupted read command due to the warm
+ * reset occurrence but SDRC is waiting for read completion.
+ * SDRC is not sensitive to the warm reset, but the interconnect is
+ * reset on the fly, thus causing a misalignment between SDRC logic,
+ * interconnect logic and DDR memory state.
+ * WORKAROUND:
+ * Steps to perform before a Warm reset is trigged:
+ * 1. enable self-refresh on idle request
+ * 2. put SDRC in idle
+ * 3. wait until SDRC goes to idle
+ * 4. generate SW reset (Global SW reset)
+ *
+ * Steps to be performed after warm reset occurs (in bootloader):
+ * if HW warm reset is the source, apply below steps before any
+ * accesses to SDRAM:
+ * 1. Reset SMS and SDRC and wait till reset is complete
+ * 2. Re-initialize SMS, SDRC and memory
+ *
+ * NOTE: Above work around is required only if arch reset is implemented
+ * using Global SW reset(GLOBAL_SW_RST). DPLL3 reset does not need
+ * the WA since it resets SDRC as well as part of cold reset.
+ */
+
+ /* XXX should be moved to some OMAP2/3 specific code */
+ omap2_prm_set_mod_reg_bits(OMAP_RST_DPLL3_MASK, prcm_offs,
+ OMAP2_RM_RSTCTRL);
+ omap2_prm_read_mod_reg(prcm_offs, OMAP2_RM_RSTCTRL); /* OCP barrier */
+}
+
+/**
+ * omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
+ * @reg: physical address of module IDLEST register
+ * @mask: value to mask against to determine if the module is active
+ * @idlest: idle state indicator (0 or 1) for the clock
+ * @name: name of the clock (for printk)
+ *
+ * Returns 1 if the module indicated readiness in time, or 0 if it
+ * failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds.
+ *
+ * XXX This function is deprecated. It should be removed once the
+ * hwmod conversion is complete.
+ */
+int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
+ const char *name)
+{
+ int i = 0;
+ int ena = 0;
+
+ if (idlest)
+ ena = 0;
+ else
+ ena = mask;
+
+ /* Wait for lock */
+ omap_test_timeout(((__raw_readl(reg) & mask) == ena),
+ MAX_MODULE_ENABLE_WAIT, i);
+
+ if (i < MAX_MODULE_ENABLE_WAIT)
+ pr_debug("cm: Module associated with clock %s ready after %d "
+ "loops\n", name, i);
+ else
+ pr_err("cm: Module associated with clock %s didn't enable in "
+ "%d tries\n", name, MAX_MODULE_ENABLE_WAIT);
+
+ return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0;
+};
+
+void __init omap2_set_globals_prcm(struct omap_globals *omap2_globals)
+{
+ if (omap2_globals->prm)
+ prm_base = omap2_globals->prm;
+ if (omap2_globals->cm)
+ cm_base = omap2_globals->cm;
+ if (omap2_globals->cm2)
+ cm2_base = omap2_globals->cm2;
+}