zte's code,first commit
Change-Id: I9a04da59e459a9bc0d67f101f700d9d7dc8d681b
diff --git a/ap/os/linux/linux-3.4.x/arch/arm/mach-ux500/board-mop500.h b/ap/os/linux/linux-3.4.x/arch/arm/mach-ux500/board-mop500.h
new file mode 100644
index 0000000..fdcfa87
--- /dev/null
+++ b/ap/os/linux/linux-3.4.x/arch/arm/mach-ux500/board-mop500.h
@@ -0,0 +1,91 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#ifndef __BOARD_MOP500_H
+#define __BOARD_MOP500_H
+
+/* Snowball specific GPIO assignments, this board has no GPIO expander */
+#define SNOWBALL_ACCEL_INT1_GPIO 163
+#define SNOWBALL_ACCEL_INT2_GPIO 164
+#define SNOWBALL_MAGNET_DRDY_GPIO 165
+#define SNOWBALL_SDMMC_EN_GPIO 217
+#define SNOWBALL_SDMMC_1V8_3V_GPIO 228
+#define SNOWBALL_SDMMC_CD_GPIO 218
+
+/* HREFv60-specific GPIO assignments, this board has no GPIO expander */
+#define HREFV60_SDMMC_1V8_3V_GPIO 5
+#define HREFV60_CAMERA_FLASH_ENABLE 21
+#define HREFV60_MAGNET_DRDY_GPIO 32
+#define HREFV60_DISP1_RST_GPIO 65
+#define HREFV60_DISP2_RST_GPIO 66
+#define HREFV60_ACCEL_INT1_GPIO 82
+#define HREFV60_ACCEL_INT2_GPIO 83
+#define HREFV60_SDMMC_CD_GPIO 95
+#define HREFV60_XSHUTDOWN_SECONDARY_SENSOR 140
+#define HREFV60_TOUCH_RST_GPIO 143
+#define HREFV60_HAL_SW_GPIO 145
+#define HREFV60_SDMMC_EN_GPIO 169
+#define HREFV60_MMIO_XENON_CHARGE 170
+#define HREFV60_PROX_SENSE_GPIO 217
+
+/* MOP500 generic GPIOs */
+#define CAMERA_FLASH_INT_PIN 7
+#define CYPRESS_TOUCH_INT_PIN 84
+#define XSHUTDOWN_PRIMARY_SENSOR 141
+#define XSHUTDOWN_SECONDARY_SENSOR 142
+#define CYPRESS_TOUCH_RST_GPIO 143
+#define MOP500_HDMI_RST_GPIO 196
+#define CYPRESS_SLAVE_SELECT_GPIO 216
+
+/* GPIOs on the TC35892 expander */
+#define MOP500_EGPIO(x) (NOMADIK_NR_GPIO + (x))
+#define GPIO_MAGNET_DRDY MOP500_EGPIO(1)
+#define GPIO_SDMMC_CD MOP500_EGPIO(3)
+#define GPIO_CAMERA_FLASH_ENABLE MOP500_EGPIO(4)
+#define GPIO_MMIO_XENON_CHARGE MOP500_EGPIO(5)
+#define GPIO_PROX_SENSOR MOP500_EGPIO(7)
+#define GPIO_HAL_SENSOR MOP500_EGPIO(8)
+#define GPIO_ACCEL_INT1 MOP500_EGPIO(10)
+#define GPIO_ACCEL_INT2 MOP500_EGPIO(11)
+#define GPIO_BU21013_CS MOP500_EGPIO(13)
+#define MOP500_DISP2_RST_GPIO MOP500_EGPIO(14)
+#define MOP500_DISP1_RST_GPIO MOP500_EGPIO(15)
+#define GPIO_SDMMC_EN MOP500_EGPIO(17)
+#define GPIO_SDMMC_1V8_3V_SEL MOP500_EGPIO(18)
+#define MOP500_EGPIO_END MOP500_EGPIO(24)
+
+/*
+ * GPIOs on the AB8500 mixed-signals circuit
+ * Notice that we subtract 1 from the number passed into the macro, this is
+ * because the AB8500 GPIO pins are enumbered starting from 1, so the value in
+ * parens matches the GPIO pin number in the data sheet.
+ */
+#define MOP500_AB8500_PIN_GPIO(x) (MOP500_EGPIO_END + (x) - 1)
+/*Snowball AB8500 GPIO */
+#define SNOWBALL_VSMPS2_1V8_GPIO MOP500_AB8500_PIN_GPIO(1) /* SYSCLKREQ2/GPIO1 */
+#define SNOWBALL_PM_GPIO1_GPIO MOP500_AB8500_PIN_GPIO(2) /* SYSCLKREQ3/GPIO2 */
+#define SNOWBALL_WLAN_CLK_REQ_GPIO MOP500_AB8500_PIN_GPIO(3) /* SYSCLKREQ4/GPIO3 */
+#define SNOWBALL_PM_GPIO4_GPIO MOP500_AB8500_PIN_GPIO(4) /* SYSCLKREQ6/GPIO4 */
+#define SNOWBALL_EN_3V6_GPIO MOP500_AB8500_PIN_GPIO(16) /* PWMOUT3/GPIO16 */
+#define SNOWBALL_PME_ETH_GPIO MOP500_AB8500_PIN_GPIO(24) /* SYSCLKREQ7/GPIO24 */
+#define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* GPIO26 */
+
+struct i2c_board_info;
+
+extern void mop500_sdi_init(struct device *parent);
+extern void snowball_sdi_init(struct device *parent);
+extern void hrefv60_sdi_init(struct device *parent);
+extern void mop500_sdi_tc35892_init(struct device *parent);
+void __init mop500_u8500uib_init(void);
+void __init mop500_stuib_init(void);
+void __init mop500_pins_init(void);
+void __init hrefv60_pins_init(void);
+void __init snowball_pins_init(void);
+
+void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
+ unsigned n);
+
+#endif