zte's code,first commit
Change-Id: I9a04da59e459a9bc0d67f101f700d9d7dc8d681b
diff --git a/ap/os/linux/linux-3.4.x/drivers/mmc/host/atmel-mci-regs.h b/ap/os/linux/linux-3.4.x/drivers/mmc/host/atmel-mci-regs.h
new file mode 100644
index 0000000..787aba1
--- /dev/null
+++ b/ap/os/linux/linux-3.4.x/drivers/mmc/host/atmel-mci-regs.h
@@ -0,0 +1,143 @@
+/*
+ * Atmel MultiMedia Card Interface driver
+ *
+ * Copyright (C) 2004-2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors
+ * Registers and bitfields marked with [2] are only available in MCI2
+ */
+
+#ifndef __DRIVERS_MMC_ATMEL_MCI_H__
+#define __DRIVERS_MMC_ATMEL_MCI_H__
+
+/* MCI Register Definitions */
+#define ATMCI_CR 0x0000 /* Control */
+# define ATMCI_CR_MCIEN ( 1 << 0) /* MCI Enable */
+# define ATMCI_CR_MCIDIS ( 1 << 1) /* MCI Disable */
+# define ATMCI_CR_PWSEN ( 1 << 2) /* Power Save Enable */
+# define ATMCI_CR_PWSDIS ( 1 << 3) /* Power Save Disable */
+# define ATMCI_CR_SWRST ( 1 << 7) /* Software Reset */
+#define ATMCI_MR 0x0004 /* Mode */
+# define ATMCI_MR_CLKDIV(x) ((x) << 0) /* Clock Divider */
+# define ATMCI_MR_PWSDIV(x) ((x) << 8) /* Power Saving Divider */
+# define ATMCI_MR_RDPROOF ( 1 << 11) /* Read Proof */
+# define ATMCI_MR_WRPROOF ( 1 << 12) /* Write Proof */
+# define ATMCI_MR_PDCFBYTE ( 1 << 13) /* Force Byte Transfer */
+# define ATMCI_MR_PDCPADV ( 1 << 14) /* Padding Value */
+# define ATMCI_MR_PDCMODE ( 1 << 15) /* PDC-oriented Mode */
+# define ATMCI_MR_CLKODD(x) ((x) << 16) /* LSB of Clock Divider */
+#define ATMCI_DTOR 0x0008 /* Data Timeout */
+# define ATMCI_DTOCYC(x) ((x) << 0) /* Data Timeout Cycles */
+# define ATMCI_DTOMUL(x) ((x) << 4) /* Data Timeout Multiplier */
+#define ATMCI_SDCR 0x000c /* SD Card / SDIO */
+# define ATMCI_SDCSEL_SLOT_A ( 0 << 0) /* Select SD slot A */
+# define ATMCI_SDCSEL_SLOT_B ( 1 << 0) /* Select SD slot A */
+# define ATMCI_SDCSEL_MASK ( 3 << 0)
+# define ATMCI_SDCBUS_1BIT ( 0 << 6) /* 1-bit data bus */
+# define ATMCI_SDCBUS_4BIT ( 2 << 6) /* 4-bit data bus */
+# define ATMCI_SDCBUS_8BIT ( 3 << 6) /* 8-bit data bus[2] */
+# define ATMCI_SDCBUS_MASK ( 3 << 6)
+#define ATMCI_ARGR 0x0010 /* Command Argument */
+#define ATMCI_CMDR 0x0014 /* Command */
+# define ATMCI_CMDR_CMDNB(x) ((x) << 0) /* Command Opcode */
+# define ATMCI_CMDR_RSPTYP_NONE ( 0 << 6) /* No response */
+# define ATMCI_CMDR_RSPTYP_48BIT ( 1 << 6) /* 48-bit response */
+# define ATMCI_CMDR_RSPTYP_136BIT ( 2 << 6) /* 136-bit response */
+# define ATMCI_CMDR_SPCMD_INIT ( 1 << 8) /* Initialization command */
+# define ATMCI_CMDR_SPCMD_SYNC ( 2 << 8) /* Synchronized command */
+# define ATMCI_CMDR_SPCMD_INT ( 4 << 8) /* Interrupt command */
+# define ATMCI_CMDR_SPCMD_INTRESP ( 5 << 8) /* Interrupt response */
+# define ATMCI_CMDR_OPDCMD ( 1 << 11) /* Open Drain */
+# define ATMCI_CMDR_MAXLAT_5CYC ( 0 << 12) /* Max latency 5 cycles */
+# define ATMCI_CMDR_MAXLAT_64CYC ( 1 << 12) /* Max latency 64 cycles */
+# define ATMCI_CMDR_START_XFER ( 1 << 16) /* Start data transfer */
+# define ATMCI_CMDR_STOP_XFER ( 2 << 16) /* Stop data transfer */
+# define ATMCI_CMDR_TRDIR_WRITE ( 0 << 18) /* Write data */
+# define ATMCI_CMDR_TRDIR_READ ( 1 << 18) /* Read data */
+# define ATMCI_CMDR_BLOCK ( 0 << 19) /* Single-block transfer */
+# define ATMCI_CMDR_MULTI_BLOCK ( 1 << 19) /* Multi-block transfer */
+# define ATMCI_CMDR_STREAM ( 2 << 19) /* MMC Stream transfer */
+# define ATMCI_CMDR_SDIO_BYTE ( 4 << 19) /* SDIO Byte transfer */
+# define ATMCI_CMDR_SDIO_BLOCK ( 5 << 19) /* SDIO Block transfer */
+# define ATMCI_CMDR_SDIO_SUSPEND ( 1 << 24) /* SDIO Suspend Command */
+# define ATMCI_CMDR_SDIO_RESUME ( 2 << 24) /* SDIO Resume Command */
+#define ATMCI_BLKR 0x0018 /* Block */
+# define ATMCI_BCNT(x) ((x) << 0) /* Data Block Count */
+# define ATMCI_BLKLEN(x) ((x) << 16) /* Data Block Length */
+#define ATMCI_CSTOR 0x001c /* Completion Signal Timeout[2] */
+# define ATMCI_CSTOCYC(x) ((x) << 0) /* CST cycles */
+# define ATMCI_CSTOMUL(x) ((x) << 4) /* CST multiplier */
+#define ATMCI_RSPR 0x0020 /* Response 0 */
+#define ATMCI_RSPR1 0x0024 /* Response 1 */
+#define ATMCI_RSPR2 0x0028 /* Response 2 */
+#define ATMCI_RSPR3 0x002c /* Response 3 */
+#define ATMCI_RDR 0x0030 /* Receive Data */
+#define ATMCI_TDR 0x0034 /* Transmit Data */
+#define ATMCI_SR 0x0040 /* Status */
+#define ATMCI_IER 0x0044 /* Interrupt Enable */
+#define ATMCI_IDR 0x0048 /* Interrupt Disable */
+#define ATMCI_IMR 0x004c /* Interrupt Mask */
+# define ATMCI_CMDRDY ( 1 << 0) /* Command Ready */
+# define ATMCI_RXRDY ( 1 << 1) /* Receiver Ready */
+# define ATMCI_TXRDY ( 1 << 2) /* Transmitter Ready */
+# define ATMCI_BLKE ( 1 << 3) /* Data Block Ended */
+# define ATMCI_DTIP ( 1 << 4) /* Data Transfer In Progress */
+# define ATMCI_NOTBUSY ( 1 << 5) /* Data Not Busy */
+# define ATMCI_ENDRX ( 1 << 6) /* End of RX Buffer */
+# define ATMCI_ENDTX ( 1 << 7) /* End of TX Buffer */
+# define ATMCI_SDIOIRQA ( 1 << 8) /* SDIO IRQ in slot A */
+# define ATMCI_SDIOIRQB ( 1 << 9) /* SDIO IRQ in slot B */
+# define ATMCI_SDIOWAIT ( 1 << 12) /* SDIO Read Wait Operation Status */
+# define ATMCI_CSRCV ( 1 << 13) /* CE-ATA Completion Signal Received */
+# define ATMCI_RXBUFF ( 1 << 14) /* RX Buffer Full */
+# define ATMCI_TXBUFE ( 1 << 15) /* TX Buffer Empty */
+# define ATMCI_RINDE ( 1 << 16) /* Response Index Error */
+# define ATMCI_RDIRE ( 1 << 17) /* Response Direction Error */
+# define ATMCI_RCRCE ( 1 << 18) /* Response CRC Error */
+# define ATMCI_RENDE ( 1 << 19) /* Response End Bit Error */
+# define ATMCI_RTOE ( 1 << 20) /* Response Time-Out Error */
+# define ATMCI_DCRCE ( 1 << 21) /* Data CRC Error */
+# define ATMCI_DTOE ( 1 << 22) /* Data Time-Out Error */
+# define ATMCI_CSTOE ( 1 << 23) /* Completion Signal Time-out Error */
+# define ATMCI_BLKOVRE ( 1 << 24) /* DMA Block Overrun Error */
+# define ATMCI_DMADONE ( 1 << 25) /* DMA Transfer Done */
+# define ATMCI_FIFOEMPTY ( 1 << 26) /* FIFO Empty Flag */
+# define ATMCI_XFRDONE ( 1 << 27) /* Transfer Done Flag */
+# define ATMCI_ACKRCV ( 1 << 28) /* Boot Operation Acknowledge Received */
+# define ATMCI_ACKRCVE ( 1 << 29) /* Boot Operation Acknowledge Error */
+# define ATMCI_OVRE ( 1 << 30) /* RX Overrun Error */
+# define ATMCI_UNRE ( 1 << 31) /* TX Underrun Error */
+#define ATMCI_DMA 0x0050 /* DMA Configuration[2] */
+# define ATMCI_DMA_OFFSET(x) ((x) << 0) /* DMA Write Buffer Offset */
+# define ATMCI_DMA_CHKSIZE(x) ((x) << 4) /* DMA Channel Read and Write Chunk Size */
+# define ATMCI_DMAEN ( 1 << 8) /* DMA Hardware Handshaking Enable */
+#define ATMCI_CFG 0x0054 /* Configuration[2] */
+# define ATMCI_CFG_FIFOMODE_1DATA ( 1 << 0) /* MCI Internal FIFO control mode */
+# define ATMCI_CFG_FERRCTRL_COR ( 1 << 4) /* Flow Error flag reset control mode */
+# define ATMCI_CFG_HSMODE ( 1 << 8) /* High Speed Mode */
+# define ATMCI_CFG_LSYNC ( 1 << 12) /* Synchronize on the last block */
+#define ATMCI_WPMR 0x00e4 /* Write Protection Mode[2] */
+# define ATMCI_WP_EN ( 1 << 0) /* WP Enable */
+# define ATMCI_WP_KEY (0x4d4349 << 8) /* WP Key */
+#define ATMCI_WPSR 0x00e8 /* Write Protection Status[2] */
+# define ATMCI_GET_WP_VS(x) ((x) & 0x0f)
+# define ATMCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff)
+#define ATMCI_VERSION 0x00FC /* Version */
+#define ATMCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */
+
+/* This is not including the FIFO Aperture on MCI2 */
+#define ATMCI_REGS_SIZE 0x100
+
+/* Register access macros */
+#define atmci_readl(port,reg) \
+ __raw_readl((port)->regs + reg)
+#define atmci_writel(port,reg,value) \
+ __raw_writel((value), (port)->regs + reg)
+
+#endif /* __DRIVERS_MMC_ATMEL_MCI_H__ */