zte's code,first commit
Change-Id: I9a04da59e459a9bc0d67f101f700d9d7dc8d681b
diff --git a/ap/os/linux/linux-3.4.x/drivers/mmc/host/imxmmc.h b/ap/os/linux/linux-3.4.x/drivers/mmc/host/imxmmc.h
new file mode 100644
index 0000000..09d5d4e
--- /dev/null
+++ b/ap/os/linux/linux-3.4.x/drivers/mmc/host/imxmmc.h
@@ -0,0 +1,64 @@
+#define MMC_REG_STR_STP_CLK 0x00
+#define MMC_REG_STATUS 0x04
+#define MMC_REG_CLK_RATE 0x08
+#define MMC_REG_CMD_DAT_CONT 0x0C
+#define MMC_REG_RES_TO 0x10
+#define MMC_REG_READ_TO 0x14
+#define MMC_REG_BLK_LEN 0x18
+#define MMC_REG_NOB 0x1C
+#define MMC_REG_REV_NO 0x20
+#define MMC_REG_INT_MASK 0x24
+#define MMC_REG_CMD 0x28
+#define MMC_REG_ARGH 0x2C
+#define MMC_REG_ARGL 0x30
+#define MMC_REG_RES_FIFO 0x34
+#define MMC_REG_BUFFER_ACCESS 0x38
+
+#define STR_STP_CLK_IPG_CLK_GATE_DIS (1<<15)
+#define STR_STP_CLK_IPG_PERCLK_GATE_DIS (1<<14)
+#define STR_STP_CLK_ENDIAN (1<<5)
+#define STR_STP_CLK_RESET (1<<3)
+#define STR_STP_CLK_ENABLE (1<<2)
+#define STR_STP_CLK_START_CLK (1<<1)
+#define STR_STP_CLK_STOP_CLK (1<<0)
+#define STATUS_CARD_PRESENCE (1<<15)
+#define STATUS_SDIO_INT_ACTIVE (1<<14)
+#define STATUS_END_CMD_RESP (1<<13)
+#define STATUS_WRITE_OP_DONE (1<<12)
+#define STATUS_DATA_TRANS_DONE (1<<11)
+#define STATUS_WR_CRC_ERROR_CODE_MASK (3<<10)
+#define STATUS_CARD_BUS_CLK_RUN (1<<8)
+#define STATUS_APPL_BUFF_FF (1<<7)
+#define STATUS_APPL_BUFF_FE (1<<6)
+#define STATUS_RESP_CRC_ERR (1<<5)
+#define STATUS_CRC_READ_ERR (1<<3)
+#define STATUS_CRC_WRITE_ERR (1<<2)
+#define STATUS_TIME_OUT_RESP (1<<1)
+#define STATUS_TIME_OUT_READ (1<<0)
+#define STATUS_ERR_MASK 0x2f
+#define CLK_RATE_PRESCALER(x) ((x) & 0x7)
+#define CLK_RATE_CLK_RATE(x) (((x) & 0x7) << 3)
+#define CMD_DAT_CONT_CMD_RESP_LONG_OFF (1<<12)
+#define CMD_DAT_CONT_STOP_READWAIT (1<<11)
+#define CMD_DAT_CONT_START_READWAIT (1<<10)
+#define CMD_DAT_CONT_BUS_WIDTH_1 (0<<8)
+#define CMD_DAT_CONT_BUS_WIDTH_4 (2<<8)
+#define CMD_DAT_CONT_INIT (1<<7)
+#define CMD_DAT_CONT_BUSY (1<<6)
+#define CMD_DAT_CONT_STREAM_BLOCK (1<<5)
+#define CMD_DAT_CONT_WRITE (1<<4)
+#define CMD_DAT_CONT_DATA_ENABLE (1<<3)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R1 (1)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R2 (2)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R3 (3)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R4 (4)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R5 (5)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R6 (6)
+#define INT_MASK_AUTO_CARD_DETECT (1<<6)
+#define INT_MASK_DAT0_EN (1<<5)
+#define INT_MASK_SDIO (1<<4)
+#define INT_MASK_BUF_READY (1<<3)
+#define INT_MASK_END_CMD_RES (1<<2)
+#define INT_MASK_WRITE_OP_DONE (1<<1)
+#define INT_MASK_DATA_TRAN (1<<0)
+#define INT_ALL (0x7f)