zte's code,first commit
Change-Id: I9a04da59e459a9bc0d67f101f700d9d7dc8d681b
diff --git a/ap/os/linux/linux-3.4.x/drivers/net/can/Kconfig b/ap/os/linux/linux-3.4.x/drivers/net/can/Kconfig
new file mode 100644
index 0000000..bb709fd
--- /dev/null
+++ b/ap/os/linux/linux-3.4.x/drivers/net/can/Kconfig
@@ -0,0 +1,134 @@
+menu "CAN Device Drivers"
+ depends on CAN
+
+config CAN_VCAN
+ tristate "Virtual Local CAN Interface (vcan)"
+ depends on CAN
+ ---help---
+ Similar to the network loopback devices, vcan offers a
+ virtual local CAN interface.
+
+ This driver can also be built as a module. If so, the module
+ will be called vcan.
+
+config CAN_SLCAN
+ tristate "Serial / USB serial CAN Adaptors (slcan)"
+ depends on CAN
+ ---help---
+ CAN driver for several 'low cost' CAN interfaces that are attached
+ via serial lines or via USB-to-serial adapters using the LAWICEL
+ ASCII protocol. The driver implements the tty linediscipline N_SLCAN.
+
+ As only the sending and receiving of CAN frames is implemented, this
+ driver should work with the (serial/USB) CAN hardware from:
+ www.canusb.com / www.can232.com / www.mictronics.de / www.canhack.de
+
+ Userspace tools to attach the SLCAN line discipline (slcan_attach,
+ slcand) can be found in the can-utils at the SocketCAN SVN, see
+ http://developer.berlios.de/projects/socketcan for details.
+
+ The slcan driver supports up to 10 CAN netdevices by default which
+ can be changed by the 'maxdev=xx' module option. This driver can
+ also be built as a module. If so, the module will be called slcan.
+
+config CAN_DEV
+ tristate "Platform CAN drivers with Netlink support"
+ depends on CAN
+ default y
+ ---help---
+ Enables the common framework for platform CAN drivers with Netlink
+ support. This is the standard library for CAN drivers.
+ If unsure, say Y.
+
+config CAN_CALC_BITTIMING
+ bool "CAN bit-timing calculation"
+ depends on CAN_DEV
+ default y
+ ---help---
+ If enabled, CAN bit-timing parameters will be calculated for the
+ bit-rate specified via Netlink argument "bitrate" when the device
+ get started. This works fine for the most common CAN controllers
+ with standard bit-rates but may fail for exotic bit-rates or CAN
+ source clock frequencies. Disabling saves some space, but then the
+ bit-timing parameters must be specified directly using the Netlink
+ arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw".
+ If unsure, say Y.
+
+config CAN_AT91
+ tristate "Atmel AT91 onchip CAN controller"
+ depends on CAN_DEV && (ARCH_AT91SAM9263 || ARCH_AT91SAM9X5)
+ ---help---
+ This is a driver for the SoC CAN controller in Atmel's AT91SAM9263
+ and AT91SAM9X5 processors.
+
+config CAN_TI_HECC
+ depends on CAN_DEV && ARCH_OMAP3
+ tristate "TI High End CAN Controller"
+ ---help---
+ Driver for TI HECC (High End CAN Controller) module found on many
+ TI devices. The device specifications are available from www.ti.com
+
+config CAN_MCP251X
+ tristate "Microchip MCP251x SPI CAN controllers"
+ depends on CAN_DEV && SPI && HAS_DMA
+ ---help---
+ Driver for the Microchip MCP251x SPI CAN controllers.
+
+config CAN_BFIN
+ depends on CAN_DEV && (BF534 || BF536 || BF537 || BF538 || BF539 || BF54x)
+ tristate "Analog Devices Blackfin on-chip CAN"
+ ---help---
+ Driver for the Analog Devices Blackfin on-chip CAN controllers
+
+ To compile this driver as a module, choose M here: the
+ module will be called bfin_can.
+
+config CAN_JANZ_ICAN3
+ tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
+ depends on CAN_DEV && MFD_JANZ_CMODIO
+ ---help---
+ Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
+ connects to a MODULbus carrier board.
+
+ This driver can also be built as a module. If so, the module will be
+ called janz-ican3.ko.
+
+config HAVE_CAN_FLEXCAN
+ bool
+
+config CAN_FLEXCAN
+ tristate "Support for Freescale FLEXCAN based chips"
+ depends on CAN_DEV && HAVE_CAN_FLEXCAN
+ ---help---
+ Say Y here if you want to support for Freescale FlexCAN.
+
+config PCH_CAN
+ tristate "Intel EG20T PCH CAN controller"
+ depends on CAN_DEV && PCI
+ ---help---
+ This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which
+ is an IOH for x86 embedded processor (Intel Atom E6xx series).
+ This driver can access CAN bus.
+
+source "drivers/net/can/mscan/Kconfig"
+
+source "drivers/net/can/sja1000/Kconfig"
+
+source "drivers/net/can/c_can/Kconfig"
+
+source "drivers/net/can/cc770/Kconfig"
+
+source "drivers/net/can/usb/Kconfig"
+
+source "drivers/net/can/softing/Kconfig"
+
+config CAN_DEBUG_DEVICES
+ bool "CAN devices debugging messages"
+ depends on CAN
+ ---help---
+ Say Y here if you want the CAN device drivers to produce a bunch of
+ debug messages to the system log. Select this if you are having
+ a problem with CAN support and want to see more of what is going
+ on.
+
+endmenu