zte's code,first commit
Change-Id: I9a04da59e459a9bc0d67f101f700d9d7dc8d681b
diff --git a/ap/os/linux/linux-3.4.x/drivers/usb/serial/ssu100.c b/ap/os/linux/linux-3.4.x/drivers/usb/serial/ssu100.c
new file mode 100644
index 0000000..f425507
--- /dev/null
+++ b/ap/os/linux/linux-3.4.x/drivers/usb/serial/ssu100.c
@@ -0,0 +1,700 @@
+/*
+ * usb-serial driver for Quatech SSU-100
+ *
+ * based on ftdi_sio.c and the original serqt_usb.c from Quatech
+ *
+ */
+
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_driver.h>
+#include <linux/tty_flip.h>
+#include <linux/module.h>
+#include <linux/serial.h>
+#include <linux/usb.h>
+#include <linux/usb/serial.h>
+#include <linux/serial_reg.h>
+#include <linux/uaccess.h>
+
+#define QT_OPEN_CLOSE_CHANNEL 0xca
+#define QT_SET_GET_DEVICE 0xc2
+#define QT_SET_GET_REGISTER 0xc0
+#define QT_GET_SET_PREBUF_TRIG_LVL 0xcc
+#define QT_SET_ATF 0xcd
+#define QT_GET_SET_UART 0xc1
+#define QT_TRANSFER_IN 0xc0
+#define QT_HW_FLOW_CONTROL_MASK 0xc5
+#define QT_SW_FLOW_CONTROL_MASK 0xc6
+
+#define SERIAL_MSR_MASK 0xf0
+
+#define SERIAL_CRTSCTS ((UART_MCR_RTS << 8) | UART_MSR_CTS)
+
+#define SERIAL_EVEN_PARITY (UART_LCR_PARITY | UART_LCR_EPAR)
+
+#define MAX_BAUD_RATE 460800
+
+#define ATC_DISABLED 0x00
+#define DUPMODE_BITS 0xc0
+#define RR_BITS 0x03
+#define LOOPMODE_BITS 0x41
+#define RS232_MODE 0x00
+#define RTSCTS_TO_CONNECTOR 0x40
+#define CLKS_X4 0x02
+#define FULLPWRBIT 0x00000080
+#define NEXT_BOARD_POWER_BIT 0x00000004
+
+static bool debug;
+
+/* Version Information */
+#define DRIVER_VERSION "v0.1"
+#define DRIVER_DESC "Quatech SSU-100 USB to Serial Driver"
+
+#define USB_VENDOR_ID_QUATECH 0x061d /* Quatech VID */
+#define QUATECH_SSU100 0xC020 /* SSU100 */
+
+static const struct usb_device_id id_table[] = {
+ {USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_SSU100)},
+ {} /* Terminating entry */
+};
+
+MODULE_DEVICE_TABLE(usb, id_table);
+
+
+static struct usb_driver ssu100_driver = {
+ .name = "ssu100",
+ .probe = usb_serial_probe,
+ .disconnect = usb_serial_disconnect,
+ .id_table = id_table,
+ .suspend = usb_serial_suspend,
+ .resume = usb_serial_resume,
+ .supports_autosuspend = 1,
+};
+
+struct ssu100_port_private {
+ spinlock_t status_lock;
+ u8 shadowLSR;
+ u8 shadowMSR;
+ struct async_icount icount;
+};
+
+static void ssu100_release(struct usb_serial *serial)
+{
+ struct ssu100_port_private *priv = usb_get_serial_port_data(*serial->port);
+
+ dbg("%s", __func__);
+ kfree(priv);
+}
+
+static inline int ssu100_control_msg(struct usb_device *dev,
+ u8 request, u16 data, u16 index)
+{
+ return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
+ request, 0x40, data, index,
+ NULL, 0, 300);
+}
+
+static inline int ssu100_setdevice(struct usb_device *dev, u8 *data)
+{
+ u16 x = ((u16)(data[1] << 8) | (u16)(data[0]));
+
+ return ssu100_control_msg(dev, QT_SET_GET_DEVICE, x, 0);
+}
+
+
+static inline int ssu100_getdevice(struct usb_device *dev, u8 *data)
+{
+ return usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
+ QT_SET_GET_DEVICE, 0xc0, 0, 0,
+ data, 3, 300);
+}
+
+static inline int ssu100_getregister(struct usb_device *dev,
+ unsigned short uart,
+ unsigned short reg,
+ u8 *data)
+{
+ return usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
+ QT_SET_GET_REGISTER, 0xc0, reg,
+ uart, data, sizeof(*data), 300);
+
+}
+
+
+static inline int ssu100_setregister(struct usb_device *dev,
+ unsigned short uart,
+ unsigned short reg,
+ u16 data)
+{
+ u16 value = (data << 8) | reg;
+
+ return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
+ QT_SET_GET_REGISTER, 0x40, value, uart,
+ NULL, 0, 300);
+
+}
+
+#define set_mctrl(dev, set) update_mctrl((dev), (set), 0)
+#define clear_mctrl(dev, clear) update_mctrl((dev), 0, (clear))
+
+/* these do not deal with device that have more than 1 port */
+static inline int update_mctrl(struct usb_device *dev, unsigned int set,
+ unsigned int clear)
+{
+ unsigned urb_value;
+ int result;
+
+ if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0) {
+ dbg("%s - DTR|RTS not being set|cleared", __func__);
+ return 0; /* no change */
+ }
+
+ clear &= ~set; /* 'set' takes precedence over 'clear' */
+ urb_value = 0;
+ if (set & TIOCM_DTR)
+ urb_value |= UART_MCR_DTR;
+ if (set & TIOCM_RTS)
+ urb_value |= UART_MCR_RTS;
+
+ result = ssu100_setregister(dev, 0, UART_MCR, urb_value);
+ if (result < 0)
+ dbg("%s Error from MODEM_CTRL urb", __func__);
+
+ return result;
+}
+
+static int ssu100_initdevice(struct usb_device *dev)
+{
+ u8 *data;
+ int result = 0;
+
+ dbg("%s", __func__);
+
+ data = kzalloc(3, GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ result = ssu100_getdevice(dev, data);
+ if (result < 0) {
+ dbg("%s - get_device failed %i", __func__, result);
+ goto out;
+ }
+
+ data[1] &= ~FULLPWRBIT;
+
+ result = ssu100_setdevice(dev, data);
+ if (result < 0) {
+ dbg("%s - setdevice failed %i", __func__, result);
+ goto out;
+ }
+
+ result = ssu100_control_msg(dev, QT_GET_SET_PREBUF_TRIG_LVL, 128, 0);
+ if (result < 0) {
+ dbg("%s - set prebuffer level failed %i", __func__, result);
+ goto out;
+ }
+
+ result = ssu100_control_msg(dev, QT_SET_ATF, ATC_DISABLED, 0);
+ if (result < 0) {
+ dbg("%s - set ATFprebuffer level failed %i", __func__, result);
+ goto out;
+ }
+
+ result = ssu100_getdevice(dev, data);
+ if (result < 0) {
+ dbg("%s - get_device failed %i", __func__, result);
+ goto out;
+ }
+
+ data[0] &= ~(RR_BITS | DUPMODE_BITS);
+ data[0] |= CLKS_X4;
+ data[1] &= ~(LOOPMODE_BITS);
+ data[1] |= RS232_MODE;
+
+ result = ssu100_setdevice(dev, data);
+ if (result < 0) {
+ dbg("%s - setdevice failed %i", __func__, result);
+ goto out;
+ }
+
+out: kfree(data);
+ return result;
+
+}
+
+
+static void ssu100_set_termios(struct tty_struct *tty,
+ struct usb_serial_port *port,
+ struct ktermios *old_termios)
+{
+ struct usb_device *dev = port->serial->dev;
+ struct ktermios *termios = tty->termios;
+ u16 baud, divisor, remainder;
+ unsigned int cflag = termios->c_cflag;
+ u16 urb_value = 0; /* will hold the new flags */
+ int result;
+
+ dbg("%s", __func__);
+
+ if (cflag & PARENB) {
+ if (cflag & PARODD)
+ urb_value |= UART_LCR_PARITY;
+ else
+ urb_value |= SERIAL_EVEN_PARITY;
+ }
+
+ switch (cflag & CSIZE) {
+ case CS5:
+ urb_value |= UART_LCR_WLEN5;
+ break;
+ case CS6:
+ urb_value |= UART_LCR_WLEN6;
+ break;
+ case CS7:
+ urb_value |= UART_LCR_WLEN7;
+ break;
+ default:
+ case CS8:
+ urb_value |= UART_LCR_WLEN8;
+ break;
+ }
+
+ baud = tty_get_baud_rate(tty);
+ if (!baud)
+ baud = 9600;
+
+ dbg("%s - got baud = %d\n", __func__, baud);
+
+
+ divisor = MAX_BAUD_RATE / baud;
+ remainder = MAX_BAUD_RATE % baud;
+ if (((remainder * 2) >= baud) && (baud != 110))
+ divisor++;
+
+ urb_value = urb_value << 8;
+
+ result = ssu100_control_msg(dev, QT_GET_SET_UART, divisor, urb_value);
+ if (result < 0)
+ dbg("%s - set uart failed", __func__);
+
+ if (cflag & CRTSCTS)
+ result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
+ SERIAL_CRTSCTS, 0);
+ else
+ result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
+ 0, 0);
+ if (result < 0)
+ dbg("%s - set HW flow control failed", __func__);
+
+ if (I_IXOFF(tty) || I_IXON(tty)) {
+ u16 x = ((u16)(START_CHAR(tty) << 8) | (u16)(STOP_CHAR(tty)));
+
+ result = ssu100_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
+ x, 0);
+ } else
+ result = ssu100_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
+ 0, 0);
+
+ if (result < 0)
+ dbg("%s - set SW flow control failed", __func__);
+
+}
+
+
+static int ssu100_open(struct tty_struct *tty, struct usb_serial_port *port)
+{
+ struct usb_device *dev = port->serial->dev;
+ struct ssu100_port_private *priv = usb_get_serial_port_data(port);
+ u8 *data;
+ int result;
+ unsigned long flags;
+
+ dbg("%s - port %d", __func__, port->number);
+
+ data = kzalloc(2, GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ result = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
+ QT_OPEN_CLOSE_CHANNEL,
+ QT_TRANSFER_IN, 0x01,
+ 0, data, 2, 300);
+ if (result < 0) {
+ dbg("%s - open failed %i", __func__, result);
+ kfree(data);
+ return result;
+ }
+
+ spin_lock_irqsave(&priv->status_lock, flags);
+ priv->shadowLSR = data[0];
+ priv->shadowMSR = data[1];
+ spin_unlock_irqrestore(&priv->status_lock, flags);
+
+ kfree(data);
+
+/* set to 9600 */
+ result = ssu100_control_msg(dev, QT_GET_SET_UART, 0x30, 0x0300);
+ if (result < 0)
+ dbg("%s - set uart failed", __func__);
+
+ if (tty)
+ ssu100_set_termios(tty, port, tty->termios);
+
+ return usb_serial_generic_open(tty, port);
+}
+
+static void ssu100_close(struct usb_serial_port *port)
+{
+ dbg("%s", __func__);
+ usb_serial_generic_close(port);
+}
+
+static int get_serial_info(struct usb_serial_port *port,
+ struct serial_struct __user *retinfo)
+{
+ struct serial_struct tmp;
+
+ if (!retinfo)
+ return -EFAULT;
+
+ memset(&tmp, 0, sizeof(tmp));
+ tmp.line = port->serial->minor;
+ tmp.port = 0;
+ tmp.irq = 0;
+ tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
+ tmp.xmit_fifo_size = port->bulk_out_size;
+ tmp.baud_base = 9600;
+ tmp.close_delay = 5*HZ;
+ tmp.closing_wait = 30*HZ;
+
+ if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
+ return -EFAULT;
+ return 0;
+}
+
+static int wait_modem_info(struct usb_serial_port *port, unsigned int arg)
+{
+ struct ssu100_port_private *priv = usb_get_serial_port_data(port);
+ struct async_icount prev, cur;
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->status_lock, flags);
+ prev = priv->icount;
+ spin_unlock_irqrestore(&priv->status_lock, flags);
+
+ while (1) {
+ wait_event_interruptible(port->delta_msr_wait,
+ (port->serial->disconnected ||
+ (priv->icount.rng != prev.rng) ||
+ (priv->icount.dsr != prev.dsr) ||
+ (priv->icount.dcd != prev.dcd) ||
+ (priv->icount.cts != prev.cts)));
+
+ if (signal_pending(current))
+ return -ERESTARTSYS;
+
+ if (port->serial->disconnected)
+ return -EIO;
+
+ spin_lock_irqsave(&priv->status_lock, flags);
+ cur = priv->icount;
+ spin_unlock_irqrestore(&priv->status_lock, flags);
+
+ if ((prev.rng == cur.rng) &&
+ (prev.dsr == cur.dsr) &&
+ (prev.dcd == cur.dcd) &&
+ (prev.cts == cur.cts))
+ return -EIO;
+
+ if ((arg & TIOCM_RNG && (prev.rng != cur.rng)) ||
+ (arg & TIOCM_DSR && (prev.dsr != cur.dsr)) ||
+ (arg & TIOCM_CD && (prev.dcd != cur.dcd)) ||
+ (arg & TIOCM_CTS && (prev.cts != cur.cts)))
+ return 0;
+ }
+ return 0;
+}
+
+static int ssu100_get_icount(struct tty_struct *tty,
+ struct serial_icounter_struct *icount)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct ssu100_port_private *priv = usb_get_serial_port_data(port);
+ struct async_icount cnow = priv->icount;
+
+ icount->cts = cnow.cts;
+ icount->dsr = cnow.dsr;
+ icount->rng = cnow.rng;
+ icount->dcd = cnow.dcd;
+ icount->rx = cnow.rx;
+ icount->tx = cnow.tx;
+ icount->frame = cnow.frame;
+ icount->overrun = cnow.overrun;
+ icount->parity = cnow.parity;
+ icount->brk = cnow.brk;
+ icount->buf_overrun = cnow.buf_overrun;
+
+ return 0;
+}
+
+
+
+static int ssu100_ioctl(struct tty_struct *tty,
+ unsigned int cmd, unsigned long arg)
+{
+ struct usb_serial_port *port = tty->driver_data;
+
+ dbg("%s cmd 0x%04x", __func__, cmd);
+
+ switch (cmd) {
+ case TIOCGSERIAL:
+ return get_serial_info(port,
+ (struct serial_struct __user *) arg);
+
+ case TIOCMIWAIT:
+ return wait_modem_info(port, arg);
+
+ default:
+ break;
+ }
+
+ dbg("%s arg not supported", __func__);
+
+ return -ENOIOCTLCMD;
+}
+
+static int ssu100_attach(struct usb_serial *serial)
+{
+ struct ssu100_port_private *priv;
+ struct usb_serial_port *port = *serial->port;
+
+ dbg("%s", __func__);
+
+ priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+ if (!priv) {
+ dev_err(&port->dev, "%s- kmalloc(%Zd) failed.\n", __func__,
+ sizeof(*priv));
+ return -ENOMEM;
+ }
+
+ spin_lock_init(&priv->status_lock);
+ usb_set_serial_port_data(port, priv);
+
+ return ssu100_initdevice(serial->dev);
+}
+
+static int ssu100_tiocmget(struct tty_struct *tty)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct usb_device *dev = port->serial->dev;
+ u8 *d;
+ int r;
+
+ dbg("%s\n", __func__);
+
+ d = kzalloc(2, GFP_KERNEL);
+ if (!d)
+ return -ENOMEM;
+
+ r = ssu100_getregister(dev, 0, UART_MCR, d);
+ if (r < 0)
+ goto mget_out;
+
+ r = ssu100_getregister(dev, 0, UART_MSR, d+1);
+ if (r < 0)
+ goto mget_out;
+
+ r = (d[0] & UART_MCR_DTR ? TIOCM_DTR : 0) |
+ (d[0] & UART_MCR_RTS ? TIOCM_RTS : 0) |
+ (d[1] & UART_MSR_CTS ? TIOCM_CTS : 0) |
+ (d[1] & UART_MSR_DCD ? TIOCM_CAR : 0) |
+ (d[1] & UART_MSR_RI ? TIOCM_RI : 0) |
+ (d[1] & UART_MSR_DSR ? TIOCM_DSR : 0);
+
+mget_out:
+ kfree(d);
+ return r;
+}
+
+static int ssu100_tiocmset(struct tty_struct *tty,
+ unsigned int set, unsigned int clear)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct usb_device *dev = port->serial->dev;
+
+ dbg("%s\n", __func__);
+ return update_mctrl(dev, set, clear);
+}
+
+static void ssu100_dtr_rts(struct usb_serial_port *port, int on)
+{
+ struct usb_device *dev = port->serial->dev;
+
+ dbg("%s\n", __func__);
+
+ /* Disable flow control */
+ if (!on) {
+ if (ssu100_setregister(dev, 0, UART_MCR, 0) < 0)
+ dev_err(&port->dev, "error from flowcontrol urb\n");
+ }
+ /* drop RTS and DTR */
+ if (on)
+ set_mctrl(dev, TIOCM_DTR | TIOCM_RTS);
+ else
+ clear_mctrl(dev, TIOCM_DTR | TIOCM_RTS);
+}
+
+static void ssu100_update_msr(struct usb_serial_port *port, u8 msr)
+{
+ struct ssu100_port_private *priv = usb_get_serial_port_data(port);
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->status_lock, flags);
+ priv->shadowMSR = msr;
+ spin_unlock_irqrestore(&priv->status_lock, flags);
+
+ if (msr & UART_MSR_ANY_DELTA) {
+ /* update input line counters */
+ if (msr & UART_MSR_DCTS)
+ priv->icount.cts++;
+ if (msr & UART_MSR_DDSR)
+ priv->icount.dsr++;
+ if (msr & UART_MSR_DDCD)
+ priv->icount.dcd++;
+ if (msr & UART_MSR_TERI)
+ priv->icount.rng++;
+ wake_up_interruptible(&port->delta_msr_wait);
+ }
+}
+
+static void ssu100_update_lsr(struct usb_serial_port *port, u8 lsr,
+ char *tty_flag)
+{
+ struct ssu100_port_private *priv = usb_get_serial_port_data(port);
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->status_lock, flags);
+ priv->shadowLSR = lsr;
+ spin_unlock_irqrestore(&priv->status_lock, flags);
+
+ *tty_flag = TTY_NORMAL;
+ if (lsr & UART_LSR_BRK_ERROR_BITS) {
+ /* we always want to update icount, but we only want to
+ * update tty_flag for one case */
+ if (lsr & UART_LSR_BI) {
+ priv->icount.brk++;
+ *tty_flag = TTY_BREAK;
+ usb_serial_handle_break(port);
+ }
+ if (lsr & UART_LSR_PE) {
+ priv->icount.parity++;
+ if (*tty_flag == TTY_NORMAL)
+ *tty_flag = TTY_PARITY;
+ }
+ if (lsr & UART_LSR_FE) {
+ priv->icount.frame++;
+ if (*tty_flag == TTY_NORMAL)
+ *tty_flag = TTY_FRAME;
+ }
+ if (lsr & UART_LSR_OE) {
+ priv->icount.overrun++;
+ tty_insert_flip_char(tty_port_tty_get(&port->port),
+ 0, TTY_OVERRUN);
+ }
+ }
+
+}
+
+static int ssu100_process_packet(struct urb *urb,
+ struct tty_struct *tty)
+{
+ struct usb_serial_port *port = urb->context;
+ char *packet = (char *)urb->transfer_buffer;
+ char flag = TTY_NORMAL;
+ u32 len = urb->actual_length;
+ int i;
+ char *ch;
+
+ dbg("%s - port %d", __func__, port->number);
+
+ if ((len >= 4) &&
+ (packet[0] == 0x1b) && (packet[1] == 0x1b) &&
+ ((packet[2] == 0x00) || (packet[2] == 0x01))) {
+ if (packet[2] == 0x00)
+ ssu100_update_lsr(port, packet[3], &flag);
+ if (packet[2] == 0x01)
+ ssu100_update_msr(port, packet[3]);
+
+ len -= 4;
+ ch = packet + 4;
+ } else
+ ch = packet;
+
+ if (!len)
+ return 0; /* status only */
+
+ if (port->port.console && port->sysrq) {
+ for (i = 0; i < len; i++, ch++) {
+ if (!usb_serial_handle_sysrq_char(port, *ch))
+ tty_insert_flip_char(tty, *ch, flag);
+ }
+ } else
+ tty_insert_flip_string_fixed_flag(tty, ch, flag, len);
+
+ return len;
+}
+
+static void ssu100_process_read_urb(struct urb *urb)
+{
+ struct usb_serial_port *port = urb->context;
+ struct tty_struct *tty;
+ int count;
+
+ dbg("%s", __func__);
+
+ tty = tty_port_tty_get(&port->port);
+ if (!tty)
+ return;
+
+ count = ssu100_process_packet(urb, tty);
+
+ if (count)
+ tty_flip_buffer_push(tty);
+ tty_kref_put(tty);
+}
+
+static struct usb_serial_driver ssu100_device = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "ssu100",
+ },
+ .description = DRIVER_DESC,
+ .id_table = id_table,
+ .num_ports = 1,
+ .open = ssu100_open,
+ .close = ssu100_close,
+ .attach = ssu100_attach,
+ .release = ssu100_release,
+ .dtr_rts = ssu100_dtr_rts,
+ .process_read_urb = ssu100_process_read_urb,
+ .tiocmget = ssu100_tiocmget,
+ .tiocmset = ssu100_tiocmset,
+ .get_icount = ssu100_get_icount,
+ .ioctl = ssu100_ioctl,
+ .set_termios = ssu100_set_termios,
+ .disconnect = usb_serial_generic_disconnect,
+};
+
+static struct usb_serial_driver * const serial_drivers[] = {
+ &ssu100_device, NULL
+};
+
+module_usb_serial_driver(ssu100_driver, serial_drivers);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
+
+module_param(debug, bool, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(debug, "Debug enabled or not");