[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/bsp/lk/target/stm32746g-eval2/init.c b/src/bsp/lk/target/stm32746g-eval2/init.c
new file mode 100644
index 0000000..8c34e85
--- /dev/null
+++ b/src/bsp/lk/target/stm32746g-eval2/init.c
@@ -0,0 +1,334 @@
+/*
+ * Copyright (c) 2015 Travis Geiselbrecht
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining
+ * a copy of this software and associated documentation files
+ * (the "Software"), to deal in the Software without restriction,
+ * including without limitation the rights to use, copy, modify, merge,
+ * publish, distribute, sublicense, and/or sell copies of the Software,
+ * and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
+ * IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
+ * CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
+ * TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
+ * SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <err.h>
+#include <stdlib.h>
+#include <debug.h>
+#include <trace.h>
+#include <target.h>
+#include <compiler.h>
+#include <lib/gfx.h>
+#include <dev/gpio.h>
+#include <platform/stm32.h>
+#include <platform/sdram.h>
+#include <platform/gpio.h>
+#include <platform/eth.h>
+#include <platform/qspi.h>
+#include <platform/n25q512a.h>
+#include <target/debugconfig.h>
+#include <target/gpioconfig.h>
+#include <reg.h>
+
+#if WITH_LIB_MINIP
+#include <lib/minip.h>
+#endif
+
+extern uint8_t BSP_LCD_Init(void);
+extern uint8_t BSP_SRAM_Init(void);
+
+const sdram_config_t target_sdram_config = {
+ .bus_width = SDRAM_BUS_WIDTH_32,
+ .cas_latency = SDRAM_CAS_LATENCY_3,
+ .col_bits_num = SDRAM_COLUMN_BITS_8
+};
+
+void target_early_init(void)
+{
+#if DEBUG_UART == 1
+ /* configure usart 1 pins */
+ gpio_config(GPIO_USART1_TX, GPIO_STM32_AF | GPIO_STM32_AFn(GPIO_AF7_USART1) | GPIO_PULLUP);
+ gpio_config(GPIO_USART1_RX, GPIO_STM32_AF | GPIO_STM32_AFn(GPIO_AF7_USART1) | GPIO_PULLUP);
+#else
+#error need to configure gpio pins for debug uart
+#endif
+
+ /* now that the uart gpios are configured, enable the debug uart */
+ stm32_debug_early_init();
+
+ /* initialize external sram */
+ BSP_SRAM_Init();
+
+ /* initialize the lcd panel */
+ BSP_LCD_Init();
+}
+
+void target_init(void)
+{
+ TRACE_ENTRY;
+ stm32_debug_init();
+
+ qspi_flash_init(N25Q512A_FLASH_SIZE);
+
+#if WITH_LIB_MINIP
+ uint8_t mac_addr[6];
+ gen_random_mac_address(mac_addr);
+ eth_init(mac_addr, PHY_DP83848);
+
+ /* start minip */
+ minip_set_macaddr(mac_addr);
+
+ uint32_t ip_addr = IPV4(192, 168, 0, 99);
+ uint32_t ip_mask = IPV4(255, 255, 255, 0);
+ uint32_t ip_gateway = IPV4_NONE;
+
+ minip_init(stm32_eth_send_minip_pkt, NULL, ip_addr, ip_mask, ip_gateway);
+#endif
+
+ TRACE_EXIT;
+}
+
+#if 0
+void target_set_debug_led(unsigned int led, bool on)
+{
+ switch (led) {
+ case 0:
+ gpio_set(GPIO_LED0, on);
+ break;
+ case 1:
+ gpio_set(GPIO_LED1, on);
+ break;
+ case 2:
+ gpio_set(GPIO_LED2, on);
+ break;
+ case 3:
+ gpio_set(GPIO_LED3, on);
+ break;
+ }
+}
+#endif
+
+/**
+ * @brief Initializes the ETH MSP.
+ * @param heth: ETH handle
+ * @retval None
+ */
+/* called back from the HAL_ETH_Init routine */
+void HAL_ETH_MspInit(ETH_HandleTypeDef *heth)
+{
+ GPIO_InitTypeDef GPIO_InitStructure;
+
+ /* Enable GPIOs clocks */
+ __HAL_RCC_GPIOA_CLK_ENABLE();
+ __HAL_RCC_GPIOB_CLK_ENABLE();
+ __HAL_RCC_GPIOC_CLK_ENABLE();
+ __HAL_RCC_GPIOE_CLK_ENABLE();
+ __HAL_RCC_GPIOF_CLK_ENABLE();
+ __HAL_RCC_GPIOG_CLK_ENABLE();
+ __HAL_RCC_GPIOH_CLK_ENABLE();
+ __HAL_RCC_GPIOI_CLK_ENABLE();
+
+ /* Ethernet pins configuration ************************************************/
+ /*
+ ETH_MDIO -------------------------> PA2
+ ETH_MDC --------------------------> PC1
+ ETH_PPS_OUT ----------------------> PB5
+ ETH_MII_RXD2 ---------------------> PH6
+ ETH_MII_RXD3 ---------------------> PH7
+ ETH_MII_TX_CLK -------------------> PC3
+ ETH_MII_TXD2 ---------------------> PC2
+ ETH_MII_TXD3 ---------------------> PE2
+ ETH_MII_RX_CLK -------------------> PA1
+ ETH_MII_RX_DV --------------------> PA7
+ ETH_MII_RXD0 ---------------------> PC4
+ ETH_MII_RXD1 ---------------------> PC5
+ ETH_MII_TX_EN --------------------> PG11
+ ETH_MII_TXD0 ---------------------> PG13
+ ETH_MII_TXD1 ---------------------> PG14
+ ETH_MII_RX_ER --------------------> PI10 (not configured)
+ ETH_MII_CRS ----------------------> PA0 (not configured)
+ ETH_MII_COL ----------------------> PH3 (not configured)
+ */
+
+ /* Configure PA1, PA2 and PA7 */
+ GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
+ GPIO_InitStructure.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStructure.Pull = GPIO_NOPULL;
+ GPIO_InitStructure.Alternate = GPIO_AF11_ETH;
+ GPIO_InitStructure.Pin = GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_7;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStructure);
+
+ /* Note : ETH_MDIO is connected to PA2 which is shared with other signals like SAI2_SCKB.
+ By default on STM32756G-EVAL board, PA2 is connected to SAI2_SCKB, so to connect PA2 to ETH_MDIO :
+ - unsolder bridge SB24 (SAI2_CKB)
+ - solder bridge SB5 (ETH_MDIO) */
+
+ /* Configure PB5 */
+ GPIO_InitStructure.Pin = GPIO_PIN_5;
+ HAL_GPIO_Init(GPIOB, &GPIO_InitStructure);
+
+ /* Configure PE2 */
+ GPIO_InitStructure.Pin = GPIO_PIN_2;
+ HAL_GPIO_Init(GPIOE, &GPIO_InitStructure);
+
+ /* Configure PC1, PC2, PC3, PC4 and PC5 */
+ GPIO_InitStructure.Pin = GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_4 | GPIO_PIN_5;
+ HAL_GPIO_Init(GPIOC, &GPIO_InitStructure);
+
+ /* Note : ETH_MDC is connected to PC1 which is shared with other signals like SAI1_SDA.
+ By default on STM32756G-EVAL board, PC1 is connected to SAI1_SDA, so to connect PC1 to ETH_MDC :
+ - unsolder bridge SB22 (SAI1_SDA)
+ - solder bridge SB33 (ETH_MDC) */
+
+ /* Configure PG11, PG14 and PG13 */
+ GPIO_InitStructure.Pin = GPIO_PIN_11 | GPIO_PIN_13 | GPIO_PIN_14;
+ HAL_GPIO_Init(GPIOG, &GPIO_InitStructure);
+
+ /* Configure PH6, PH7 */
+ GPIO_InitStructure.Pin = GPIO_PIN_6 | GPIO_PIN_7;
+ HAL_GPIO_Init(GPIOH, &GPIO_InitStructure);
+
+ /* Configure PA0
+ GPIO_InitStructure.Pin = GPIO_PIN_0;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStructure);
+
+ Note: Ethernet Full duplex mode works properly in the default setting
+ (which MII_CRS is not connected to PA0 of STM32F756NGH6) because PA0 is shared
+ with MC_ENA.
+ If Half duplex mode is needed, uncomment PA0 configuration code source (above
+ the note) and close the SB36 solder bridge of the STM32756G-EVAL board .
+ */
+
+ /* Configure PH3
+ GPIO_InitStructure.Pin = GPIO_PIN_3;
+ HAL_GPIO_Init(GPIOH, &GPIO_InitStructure);
+
+ Note: Ethernet Full duplex mode works properly in the default setting
+ (which MII_COL is not connected to PH3 of STM32F756NGH6) because PH3 is shared
+ with SDRAM chip select SDNE0.
+ If Half duplex mode is needed, uncomment PH3 configuration code source (above
+ the note) and close SB47 solder bridge of the STM32756G-EVAL board.
+ */
+
+ /* Configure PI10
+ GPIO_InitStructure.Pin = GPIO_PIN_10;
+ HAL_GPIO_Init(GPIOI, &GPIO_InitStructure);
+
+ Note: Ethernet works properly in the default setting (which RX_ER is not
+ connected to PI10 of STM32F756NGH6) because PI10 is shared with data signal
+ of SDRAM.
+ If RX_ER signal is needed, uncomment PI10 configuration code source (above
+ the note) then remove R248 and solder SB9 of the STM32756G-EVAL board.
+ */
+}
+
+/**
+ * @brief Initializes SDRAM GPIO.
+ * @retval None
+ */
+/* called back from BSP_SDRAM_Init */
+void stm_sdram_GPIO_init(void)
+{
+ GPIO_InitTypeDef gpio_init_structure;
+
+ /* Enable GPIOs clock */
+ __HAL_RCC_GPIOD_CLK_ENABLE();
+ __HAL_RCC_GPIOE_CLK_ENABLE();
+ __HAL_RCC_GPIOF_CLK_ENABLE();
+ __HAL_RCC_GPIOG_CLK_ENABLE();
+ __HAL_RCC_GPIOH_CLK_ENABLE();
+ __HAL_RCC_GPIOI_CLK_ENABLE();
+
+ /* Common GPIO configuration */
+ gpio_init_structure.Mode = GPIO_MODE_AF_PP;
+ gpio_init_structure.Pull = GPIO_PULLUP;
+ gpio_init_structure.Speed = GPIO_SPEED_FAST;
+ gpio_init_structure.Alternate = GPIO_AF12_FMC;
+
+ /* GPIOD configuration */
+ gpio_init_structure.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_8| GPIO_PIN_9 | GPIO_PIN_10 |\
+ GPIO_PIN_14 | GPIO_PIN_15;
+ HAL_GPIO_Init(GPIOD, &gpio_init_structure);
+
+ /* GPIOE configuration */
+ gpio_init_structure.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_7| GPIO_PIN_8 | GPIO_PIN_9 |\
+ GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_14 |\
+ GPIO_PIN_15;
+ HAL_GPIO_Init(GPIOE, &gpio_init_structure);
+
+ /* GPIOF configuration */
+ gpio_init_structure.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2| GPIO_PIN_3 | GPIO_PIN_4 |\
+ GPIO_PIN_5 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_14 |\
+ GPIO_PIN_15;
+ HAL_GPIO_Init(GPIOF, &gpio_init_structure);
+
+ /* GPIOG configuration */
+ gpio_init_structure.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_4| GPIO_PIN_5 | GPIO_PIN_8 |\
+ GPIO_PIN_15;
+ HAL_GPIO_Init(GPIOG, &gpio_init_structure);
+
+ /* GPIOH configuration */
+ gpio_init_structure.Pin = GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_5 | GPIO_PIN_8 | GPIO_PIN_9 |\
+ GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_14 |\
+ GPIO_PIN_15;
+ HAL_GPIO_Init(GPIOH, &gpio_init_structure);
+
+ /* GPIOI configuration */
+ gpio_init_structure.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_4 |\
+ GPIO_PIN_5 | GPIO_PIN_6 | GPIO_PIN_7 | GPIO_PIN_9 | GPIO_PIN_10;
+ HAL_GPIO_Init(GPIOI, &gpio_init_structure);
+}
+
+void HAL_QSPI_MspInit(QSPI_HandleTypeDef *hqspi)
+{
+ GPIO_InitTypeDef GPIO_InitStruct;
+
+ /*##-1- Enable peripherals and GPIO Clocks #################################*/
+ /* Enable GPIO clocks */
+ __HAL_RCC_GPIOB_CLK_ENABLE();
+ __HAL_RCC_GPIOF_CLK_ENABLE();
+
+ /*##-2- Configure peripheral GPIO ##########################################*/
+ /* QSPI CS GPIO pin configuration */
+ GPIO_InitStruct.Pin = GPIO_PIN_6;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_QUADSPI;
+ HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+ /* QSPI CLK GPIO pin configuration */
+ GPIO_InitStruct.Pin = GPIO_PIN_2;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF9_QUADSPI;
+ HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+ /* QSPI D0 GPIO pin configuration */
+ GPIO_InitStruct.Pin = GPIO_PIN_8;
+ GPIO_InitStruct.Alternate = GPIO_AF10_QUADSPI;
+ HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
+
+ /* QSPI D1 GPIO pin configuration */
+ GPIO_InitStruct.Pin = GPIO_PIN_9;
+ GPIO_InitStruct.Alternate = GPIO_AF10_QUADSPI;
+ HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
+
+ /* QSPI D2 GPIO pin configuration */
+ GPIO_InitStruct.Pin = GPIO_PIN_7;
+ GPIO_InitStruct.Alternate = GPIO_AF9_QUADSPI;
+ HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
+
+ /* QSPI D3 GPIO pin configuration */
+ GPIO_InitStruct.Pin = GPIO_PIN_6;
+ GPIO_InitStruct.Alternate = GPIO_AF9_QUADSPI;
+ HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
+}
+