[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/Documentation/ABI/testing/sysfs-driver-hid-wiimote b/src/kernel/linux/v4.14/Documentation/ABI/testing/sysfs-driver-hid-wiimote
new file mode 100644
index 0000000..39dfa5c
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/ABI/testing/sysfs-driver-hid-wiimote
@@ -0,0 +1,77 @@
+What: /sys/bus/hid/drivers/wiimote/<dev>/led1
+What: /sys/bus/hid/drivers/wiimote/<dev>/led2
+What: /sys/bus/hid/drivers/wiimote/<dev>/led3
+What: /sys/bus/hid/drivers/wiimote/<dev>/led4
+Date: July 2011
+KernelVersion: 3.1
+Contact: David Herrmann <dh.herrmann@googlemail.com>
+Description: Make it possible to set/get current led state. Reading from it
+ returns 0 if led is off and 1 if it is on. Writing 0 to it
+ disables the led, writing 1 enables it.
+
+What: /sys/bus/hid/drivers/wiimote/<dev>/extension
+Date: August 2011
+KernelVersion: 3.2
+Contact: David Herrmann <dh.herrmann@gmail.com>
+Description: This file contains the currently connected and initialized
+ extensions. It can be one of: none, motionp, nunchuck, classic,
+ motionp+nunchuck, motionp+classic
+ motionp is the official Nintendo Motion+ extension, nunchuck is
+ the official Nintendo Nunchuck extension and classic is the
+ Nintendo Classic Controller extension. The motionp extension can
+ be combined with the other two.
+ Starting with kernel-version 3.11 Motion Plus hotplugging is
+ supported and if detected, it's no longer reported as static
+ extension. You will get uevent notifications for the motion-plus
+ device then.
+
+What: /sys/bus/hid/drivers/wiimote/<dev>/devtype
+Date: May 2013
+KernelVersion: 3.11
+Contact: David Herrmann <dh.herrmann@gmail.com>
+Description: While a device is initialized by the wiimote driver, we perform
+ a device detection and signal a "change" uevent after it is
+ done. This file shows the detected device type. "pending" means
+ that the detection is still ongoing, "unknown" means, that the
+ device couldn't be detected or loaded. "generic" means, that the
+ device couldn't be detected but supports basic Wii Remote
+ features and can be used.
+ Other strings for each device-type are available and may be
+ added if new device-specific detections are added.
+ Currently supported are:
+ gen10: First Wii Remote generation
+ gen20: Second Wii Remote Plus generation (builtin MP)
+ balanceboard: Wii Balance Board
+
+What: /sys/bus/hid/drivers/wiimote/<dev>/bboard_calib
+Date: May 2013
+KernelVersion: 3.11
+Contact: David Herrmann <dh.herrmann@gmail.com>
+Description: This attribute is only provided if the device was detected as a
+ balance board. It provides a single line with 3 calibration
+ values for all 4 sensors. The values are separated by colons and
+ are each 2 bytes long (encoded as 4 digit hexadecimal value).
+ First, 0kg values for all 4 sensors are written, followed by the
+ 17kg values for all 4 sensors and last the 34kg values for all 4
+ sensors.
+ Calibration data is already applied by the kernel to all input
+ values but may be used by user-space to perform other
+ transformations.
+
+What: /sys/bus/hid/drivers/wiimote/<dev>/pro_calib
+Date: October 2013
+KernelVersion: 3.13
+Contact: David Herrmann <dh.herrmann@gmail.com>
+Description: This attribute is only provided if the device was detected as a
+ pro-controller. It provides a single line with 4 calibration
+ values for all 4 analog sticks. Format is: "x1:y1 x2:y2". Data
+ is prefixed with a +/-. Each value is a signed 16bit number.
+ Data is encoded as decimal numbers and specifies the offsets of
+ the analog sticks of the pro-controller.
+ Calibration data is already applied by the kernel to all input
+ values but may be used by user-space to perform other
+ transformations.
+ Calibration data is detected by the kernel during device setup.
+ You can write "scan\n" into this file to re-trigger calibration.
+ You can also write data directly in the form "x1:y1 x2:y2" to
+ set the calibration values manually.