diff --git a/src/kernel/linux/v4.14/Documentation/leds/00-INDEX b/src/kernel/linux/v4.14/Documentation/leds/00-INDEX
new file mode 100644
index 0000000..b4ef1f3
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/00-INDEX
@@ -0,0 +1,22 @@
+00-INDEX
+	- This file
+leds-blinkm.txt
+	- Driver for BlinkM LED-devices.
+leds-class.txt
+	- documents LED handling under Linux.
+leds-lp3944.txt
+	- notes on how to use the leds-lp3944 driver.
+leds-lp5521.txt
+	- notes on how to use the leds-lp5521 driver.
+leds-lp5523.txt
+	- notes on how to use the leds-lp5523 driver.
+leds-lp5562.txt
+	- notes on how to use the leds-lp5562 driver.
+leds-lp55xx.txt
+	- description about lp55xx common driver.
+leds-lm3556.txt
+	- notes on how to use the leds-lm3556 driver.
+ledtrig-oneshot.txt
+	- One-shot LED trigger for both sporadic and dense events.
+ledtrig-transient.txt
+	- LED Transient Trigger, one shot timer activation.
diff --git a/src/kernel/linux/v4.14/Documentation/leds/leds-blinkm.txt b/src/kernel/linux/v4.14/Documentation/leds/leds-blinkm.txt
new file mode 100644
index 0000000..9dd92f4
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/leds-blinkm.txt
@@ -0,0 +1,80 @@
+The leds-blinkm driver supports the devices of the BlinkM family.
+
+They are RGB-LED modules driven by a (AT)tiny microcontroller and
+communicate through I2C. The default address of these modules is
+0x09 but this can be changed through a command. By this you could
+dasy-chain up to 127 BlinkMs on an I2C bus.
+
+The device accepts RGB and HSB color values through separate commands.
+Also you can store blinking sequences as "scripts" in
+the controller and run them. Also fading is an option.
+
+The interface this driver provides is 2-fold:
+
+a) LED class interface for use with triggers
+############################################
+
+The registration follows the scheme:
+blinkm-<i2c-bus-nr>-<i2c-device-nr>-<color>
+
+$ ls -h /sys/class/leds/blinkm-6-*
+/sys/class/leds/blinkm-6-9-blue:
+brightness  device  max_brightness  power  subsystem  trigger  uevent
+
+/sys/class/leds/blinkm-6-9-green:
+brightness  device  max_brightness  power  subsystem  trigger  uevent
+
+/sys/class/leds/blinkm-6-9-red:
+brightness  device  max_brightness  power  subsystem  trigger  uevent
+
+(same is /sys/bus/i2c/devices/6-0009/leds)
+
+We can control the colors separated into red, green and blue and
+assign triggers on each color.
+
+E.g.:
+
+$ cat blinkm-6-9-blue/brightness
+05
+
+$ echo 200 > blinkm-6-9-blue/brightness
+$
+
+$ modprobe ledtrig-heartbeat
+$ echo heartbeat > blinkm-6-9-green/trigger
+$
+
+
+b) Sysfs group to control rgb, fade, hsb, scripts ...
+#####################################################
+
+This extended interface is available as folder blinkm
+in the sysfs folder of the I2C device.
+E.g. below /sys/bus/i2c/devices/6-0009/blinkm
+
+$ ls -h /sys/bus/i2c/devices/6-0009/blinkm/
+blue  green  red  test
+
+Currently supported is just setting red, green, blue
+and a test sequence.
+
+E.g.:
+
+$ cat *
+00
+00
+00
+#Write into test to start test sequence!#
+
+$ echo 1 > test
+$
+
+$ echo 255 > red
+$
+
+
+
+as of 6/2012
+
+dl9pf <at> gmx <dot> de
+
diff --git a/src/kernel/linux/v4.14/Documentation/leds/leds-class-flash.txt b/src/kernel/linux/v4.14/Documentation/leds/leds-class-flash.txt
new file mode 100644
index 0000000..8da3c6f
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/leds-class-flash.txt
@@ -0,0 +1,73 @@
+
+Flash LED handling under Linux
+==============================
+
+Some LED devices provide two modes - torch and flash. In the LED subsystem
+those modes are supported by LED class (see Documentation/leds/leds-class.txt)
+and LED Flash class respectively. The torch mode related features are enabled
+by default and the flash ones only if a driver declares it by setting
+LED_DEV_CAP_FLASH flag.
+
+In order to enable the support for flash LEDs CONFIG_LEDS_CLASS_FLASH symbol
+must be defined in the kernel config. A LED Flash class driver must be
+registered in the LED subsystem with led_classdev_flash_register function.
+
+Following sysfs attributes are exposed for controlling flash LED devices:
+(see Documentation/ABI/testing/sysfs-class-led-flash)
+	- flash_brightness
+	- max_flash_brightness
+	- flash_timeout
+	- max_flash_timeout
+	- flash_strobe
+	- flash_fault
+
+
+V4L2 flash wrapper for flash LEDs
+=================================
+
+A LED subsystem driver can be controlled also from the level of VideoForLinux2
+subsystem. In order to enable this CONFIG_V4L2_FLASH_LED_CLASS symbol has to
+be defined in the kernel config.
+
+The driver must call the v4l2_flash_init function to get registered in the
+V4L2 subsystem. The function takes six arguments:
+- dev       : flash device, e.g. an I2C device
+- of_node   : of_node of the LED, may be NULL if the same as device's
+- fled_cdev : LED flash class device to wrap
+- iled_cdev : LED flash class device representing indicator LED associated with
+	      fled_cdev, may be NULL
+- ops : V4L2 specific ops
+	* external_strobe_set - defines the source of the flash LED strobe -
+		V4L2_CID_FLASH_STROBE control or external source, typically
+		a sensor, which makes it possible to synchronise the flash
+		strobe start with exposure start,
+	* intensity_to_led_brightness and led_brightness_to_intensity - perform
+		enum led_brightness <-> V4L2 intensity conversion in a device
+		specific manner - they can be used for devices with non-linear
+		LED current scale.
+- config : configuration for V4L2 Flash sub-device
+	* dev_name - the name of the media entity, unique in the system,
+	* flash_faults - bitmask of flash faults that the LED flash class
+		device can report; corresponding LED_FAULT* bit definitions are
+		available in <linux/led-class-flash.h>,
+	* torch_intensity - constraints for the LED in TORCH mode
+		in microamperes,
+	* indicator_intensity - constraints for the indicator LED
+		in microamperes,
+	* has_external_strobe - determines whether the flash strobe source
+		can be switched to external,
+
+On remove the v4l2_flash_release function has to be called, which takes one
+argument - struct v4l2_flash pointer returned previously by v4l2_flash_init.
+This function can be safely called with NULL or error pointer argument.
+
+Please refer to drivers/leds/leds-max77693.c for an exemplary usage of the
+v4l2 flash wrapper.
+
+Once the V4L2 sub-device is registered by the driver which created the Media
+controller device, the sub-device node acts just as a node of a native V4L2
+flash API device would. The calls are simply routed to the LED flash API.
+
+Opening the V4L2 flash sub-device makes the LED subsystem sysfs interface
+unavailable. The interface is re-enabled after the V4L2 flash sub-device
+is closed.
diff --git a/src/kernel/linux/v4.14/Documentation/leds/leds-class.txt b/src/kernel/linux/v4.14/Documentation/leds/leds-class.txt
new file mode 100644
index 0000000..836cb16
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/leds-class.txt
@@ -0,0 +1,122 @@
+
+LED handling under Linux
+========================
+
+In its simplest form, the LED class just allows control of LEDs from
+userspace. LEDs appear in /sys/class/leds/. The maximum brightness of the
+LED is defined in max_brightness file. The brightness file will set the brightness
+of the LED (taking a value 0-max_brightness). Most LEDs don't have hardware
+brightness support so will just be turned on for non-zero brightness settings.
+
+The class also introduces the optional concept of an LED trigger. A trigger
+is a kernel based source of led events. Triggers can either be simple or
+complex. A simple trigger isn't configurable and is designed to slot into
+existing subsystems with minimal additional code. Examples are the disk-activity,
+nand-disk and sharpsl-charge triggers. With led triggers disabled, the code
+optimises away.
+
+Complex triggers whilst available to all LEDs have LED specific
+parameters and work on a per LED basis. The timer trigger is an example.
+The timer trigger will periodically change the LED brightness between
+LED_OFF and the current brightness setting. The "on" and "off" time can
+be specified via /sys/class/leds/<device>/delay_{on,off} in milliseconds.
+You can change the brightness value of a LED independently of the timer
+trigger. However, if you set the brightness value to LED_OFF it will
+also disable the timer trigger.
+
+You can change triggers in a similar manner to the way an IO scheduler
+is chosen (via /sys/class/leds/<device>/trigger). Trigger specific
+parameters can appear in /sys/class/leds/<device> once a given trigger is
+selected.
+
+
+Design Philosophy
+=================
+
+The underlying design philosophy is simplicity. LEDs are simple devices
+and the aim is to keep a small amount of code giving as much functionality
+as possible.  Please keep this in mind when suggesting enhancements.
+
+
+LED Device Naming
+=================
+
+Is currently of the form:
+
+"devicename:colour:function"
+
+There have been calls for LED properties such as colour to be exported as
+individual led class attributes. As a solution which doesn't incur as much
+overhead, I suggest these become part of the device name. The naming scheme
+above leaves scope for further attributes should they be needed. If sections
+of the name don't apply, just leave that section blank.
+
+
+Brightness setting API
+======================
+
+LED subsystem core exposes following API for setting brightness:
+
+    - led_set_brightness : it is guaranteed not to sleep, passing LED_OFF stops
+		blinking,
+    - led_set_brightness_sync : for use cases when immediate effect is desired -
+		it can block the caller for the time required for accessing
+		device registers and can sleep, passing LED_OFF stops hardware
+		blinking, returns -EBUSY if software blink fallback is enabled.
+
+
+LED registration API
+====================
+
+A driver wanting to register a LED classdev for use by other drivers /
+userspace needs to allocate and fill a led_classdev struct and then call
+[devm_]led_classdev_register. If the non devm version is used the driver
+must call led_classdev_unregister from its remove function before
+free-ing the led_classdev struct.
+
+If the driver can detect hardware initiated brightness changes and thus
+wants to have a brightness_hw_changed attribute then the LED_BRIGHT_HW_CHANGED
+flag must be set in flags before registering. Calling
+led_classdev_notify_brightness_hw_changed on a classdev not registered with
+the LED_BRIGHT_HW_CHANGED flag is a bug and will trigger a WARN_ON.
+
+Hardware accelerated blink of LEDs
+==================================
+
+Some LEDs can be programmed to blink without any CPU interaction. To
+support this feature, a LED driver can optionally implement the
+blink_set() function (see <linux/leds.h>). To set an LED to blinking,
+however, it is better to use the API function led_blink_set(), as it
+will check and implement software fallback if necessary.
+
+To turn off blinking, use the API function led_brightness_set()
+with brightness value LED_OFF, which should stop any software
+timers that may have been required for blinking.
+
+The blink_set() function should choose a user friendly blinking value
+if it is called with *delay_on==0 && *delay_off==0 parameters. In this
+case the driver should give back the chosen value through delay_on and
+delay_off parameters to the leds subsystem.
+
+Setting the brightness to zero with brightness_set() callback function
+should completely turn off the LED and cancel the previously programmed
+hardware blinking function, if any.
+
+
+Known Issues
+============
+
+The LED Trigger core cannot be a module as the simple trigger functions
+would cause nightmare dependency issues. I see this as a minor issue
+compared to the benefits the simple trigger functionality brings. The
+rest of the LED subsystem can be modular.
+
+
+Future Development
+==================
+
+At the moment, a trigger can't be created specifically for a single LED.
+There are a number of cases where a trigger might only be mappable to a
+particular LED (ACPI?). The addition of triggers provided by the LED driver
+should cover this option and be possible to add without breaking the
+current interface.
diff --git a/src/kernel/linux/v4.14/Documentation/leds/leds-lm3556.txt b/src/kernel/linux/v4.14/Documentation/leds/leds-lm3556.txt
new file mode 100644
index 0000000..62278e8
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/leds-lm3556.txt
@@ -0,0 +1,85 @@
+Kernel driver for lm3556
+========================
+
+*Texas Instrument:
+ 1.5 A Synchronous Boost LED Flash Driver w/ High-Side Current Source
+* Datasheet: http://www.national.com/ds/LM/LM3556.pdf
+
+Authors:
+	Daniel Jeong
+	Contact:Daniel Jeong(daniel.jeong-at-ti.com, gshark.jeong-at-gmail.com)
+
+Description
+-----------
+There are 3 functions in LM3556, Flash, Torch and Indicator.
+
+FLASH MODE
+In Flash Mode, the LED current source(LED) provides 16 target current levels
+from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT
+CONTROL REGISTER(0x09).Flash mode is activated by the ENABLE REGISTER(0x0A),
+or by pulling the STROBE pin HIGH.
+LM3556 Flash can be controlled through sys/class/leds/flash/brightness file
+* if STROBE pin is enabled, below example control brightness only, and
+ON / OFF will be controlled by STROBE pin.
+
+Flash Example:
+OFF     : #echo 0 > sys/class/leds/flash/brightness
+93.75 mA: #echo 1 > sys/class/leds/flash/brightness
+... .....
+1500  mA: #echo 16 > sys/class/leds/flash/brightness
+
+TORCH MODE
+In Torch Mode, the current source(LED) is programmed via the CURRENT CONTROL
+REGISTER(0x09).Torch Mode is activated by the ENABLE REGISTER(0x0A) or by the
+hardware TORCH input.
+LM3556 torch can be controlled through sys/class/leds/torch/brightness file.
+* if TORCH pin is enabled, below example control brightness only,
+and ON / OFF will be controlled by TORCH pin.
+
+Torch Example:
+OFF     : #echo 0 > sys/class/leds/torch/brightness
+46.88 mA: #echo 1 > sys/class/leds/torch/brightness
+... .....
+375 mA  : #echo 8 > sys/class/leds/torch/brightness
+
+INDICATOR MODE
+Indicator pattern can be set through sys/class/leds/indicator/pattern file,
+and 4 patterns are pre-defined in indicator_pattern array.
+According to N-lank, Pulse time and N Period values, different pattern wiill
+be generated.If you want new patterns for your own device, change
+indicator_pattern array with your own values and INDIC_PATTERN_SIZE.
+Please refer datasheet for more detail about N-Blank, Pulse time and N Period.
+
+Indicator pattern example:
+pattern 0: #echo 0 > sys/class/leds/indicator/pattern
+....
+pattern 3: #echo 3 > sys/class/leds/indicator/pattern
+
+Indicator brightness can be controlled through
+sys/class/leds/indicator/brightness file.
+
+Example:
+OFF      : #echo 0 > sys/class/leds/indicator/brightness
+5.86 mA  : #echo 1 > sys/class/leds/indicator/brightness
+........
+46.875mA : #echo 8 > sys/class/leds/indicator/brightness
+
+Notes
+-----
+Driver expects it is registered using the i2c_board_info mechanism.
+To register the chip at address 0x63 on specific adapter, set the platform data
+according to include/linux/platform_data/leds-lm3556.h, set the i2c board info
+
+Example:
+	static struct i2c_board_info board_i2c_ch4[] __initdata = {
+		{
+			 I2C_BOARD_INFO(LM3556_NAME, 0x63),
+			 .platform_data = &lm3556_pdata,
+		 },
+	};
+
+and register it in the platform init function
+
+Example:
+	board_register_i2c_bus(4, 400,
+				board_i2c_ch4, ARRAY_SIZE(board_i2c_ch4));
diff --git a/src/kernel/linux/v4.14/Documentation/leds/leds-lp3944.txt b/src/kernel/linux/v4.14/Documentation/leds/leds-lp3944.txt
new file mode 100644
index 0000000..e88ac3b
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/leds-lp3944.txt
@@ -0,0 +1,50 @@
+Kernel driver lp3944
+====================
+
+  * National Semiconductor LP3944 Fun-light Chip
+    Prefix: 'lp3944'
+    Addresses scanned: None (see the Notes section below)
+    Datasheet: Publicly available at the National Semiconductor website
+               http://www.national.com/pf/LP/LP3944.html
+
+Authors:
+        Antonio Ospite <ospite@studenti.unina.it>
+
+
+Description
+-----------
+The LP3944 is a helper chip that can drive up to 8 leds, with two programmable
+DIM modes; it could even be used as a gpio expander but this driver assumes it
+is used as a led controller.
+
+The DIM modes are used to set _blink_ patterns for leds, the pattern is
+specified supplying two parameters:
+  - period: from 0s to 1.6s
+  - duty cycle: percentage of the period the led is on, from 0 to 100
+
+Setting a led in DIM0 or DIM1 mode makes it blink according to the pattern.
+See the datasheet for details.
+
+LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
+leds, the camera flash light and the lcds power.
+
+
+Notes
+-----
+The chip is used mainly in embedded contexts, so this driver expects it is
+registered using the i2c_board_info mechanism.
+
+To register the chip at address 0x60 on adapter 0, set the platform data
+according to include/linux/leds-lp3944.h, set the i2c board info:
+
+	static struct i2c_board_info a910_i2c_board_info[] __initdata = {
+		{
+			I2C_BOARD_INFO("lp3944", 0x60),
+			.platform_data = &a910_lp3944_leds,
+		},
+	};
+
+and register it in the platform init function
+
+	i2c_register_board_info(0, a910_i2c_board_info,
+			ARRAY_SIZE(a910_i2c_board_info));
diff --git a/src/kernel/linux/v4.14/Documentation/leds/leds-lp5521.txt b/src/kernel/linux/v4.14/Documentation/leds/leds-lp5521.txt
new file mode 100644
index 0000000..d08d8c1
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/leds-lp5521.txt
@@ -0,0 +1,101 @@
+Kernel driver for lp5521
+========================
+
+* National Semiconductor LP5521 led driver chip
+* Datasheet: http://www.national.com/pf/LP/LP5521.html
+
+Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
+Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
+
+Description
+-----------
+
+LP5521 can drive up to 3 channels. Leds can be controlled directly via
+the led class control interface. Channels have generic names:
+lp5521:channelx, where x is 0 .. 2
+
+All three channels can be also controlled using the engine micro programs.
+More details of the instructions can be found from the public data sheet.
+
+LP5521 has the internal program memory for running various LED patterns.
+There are two ways to run LED patterns.
+
+1) Legacy interface - enginex_mode and enginex_load
+  Control interface for the engines:
+  x is 1 .. 3
+  enginex_mode : disabled, load, run
+  enginex_load : store program (visible only in engine load mode)
+
+  Example (start to blink the channel 2 led):
+  cd   /sys/class/leds/lp5521:channel2/device
+  echo "load" > engine3_mode
+  echo "037f4d0003ff6000" > engine3_load
+  echo "run" > engine3_mode
+
+  To stop the engine:
+  echo "disabled" > engine3_mode
+
+2) Firmware interface - LP55xx common interface
+  For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+sysfs contains a selftest entry.
+The test communicates with the chip and checks that
+the clock mode is automatically set to the requested one.
+
+Each channel has its own led current settings.
+/sys/class/leds/lp5521:channel0/led_current - RW
+/sys/class/leds/lp5521:channel0/max_current - RO
+Format: 10x mA i.e 10 means 1.0 mA
+
+example platform data:
+
+Note: chan_nr can have values between 0 and 2.
+The name of each channel can be configurable.
+If the name field is not defined, the default name will be set to 'xxxx:channelN'
+(XXXX : pdata->label or i2c client name, N : channel number)
+
+static struct lp55xx_led_config lp5521_led_config[] = {
+        {
+		.name = "red",
+                .chan_nr        = 0,
+                .led_current    = 50,
+		.max_current    = 130,
+        }, {
+		.name = "green",
+                .chan_nr        = 1,
+                .led_current    = 0,
+		.max_current    = 130,
+        }, {
+		.name = "blue",
+                .chan_nr        = 2,
+                .led_current    = 0,
+		.max_current    = 130,
+        }
+};
+
+static int lp5521_setup(void)
+{
+	/* setup HW resources */
+}
+
+static void lp5521_release(void)
+{
+	/* Release HW resources */
+}
+
+static void lp5521_enable(bool state)
+{
+	/* Control of chip enable signal */
+}
+
+static struct lp55xx_platform_data lp5521_platform_data = {
+        .led_config     = lp5521_led_config,
+        .num_channels   = ARRAY_SIZE(lp5521_led_config),
+        .clock_mode     = LP55XX_CLOCK_EXT,
+        .setup_resources   = lp5521_setup,
+        .release_resources = lp5521_release,
+        .enable            = lp5521_enable,
+};
+
+If the current is set to 0 in the platform data, that channel is
+disabled and it is not visible in the sysfs.
diff --git a/src/kernel/linux/v4.14/Documentation/leds/leds-lp5523.txt b/src/kernel/linux/v4.14/Documentation/leds/leds-lp5523.txt
new file mode 100644
index 0000000..0961a06
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/leds-lp5523.txt
@@ -0,0 +1,130 @@
+Kernel driver for lp5523
+========================
+
+* National Semiconductor LP5523 led driver chip
+* Datasheet: http://www.national.com/pf/LP/LP5523.html
+
+Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
+Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
+
+Description
+-----------
+LP5523 can drive up to 9 channels. Leds can be controlled directly via
+the led class control interface.
+The name of each channel is configurable in the platform data - name and label.
+There are three options to make the channel name.
+
+a) Define the 'name' in the platform data
+To make specific channel name, then use 'name' platform data.
+/sys/class/leds/R1               (name: 'R1')
+/sys/class/leds/B1               (name: 'B1')
+
+b) Use the 'label' with no 'name' field
+For one device name with channel number, then use 'label'.
+/sys/class/leds/RGB:channelN     (label: 'RGB', N: 0 ~ 8)
+
+c) Default
+If both fields are NULL, 'lp5523' is used by default.
+/sys/class/leds/lp5523:channelN  (N: 0 ~ 8)
+
+LP5523 has the internal program memory for running various LED patterns.
+There are two ways to run LED patterns.
+
+1) Legacy interface - enginex_mode, enginex_load and enginex_leds
+  Control interface for the engines:
+  x is 1 .. 3
+  enginex_mode : disabled, load, run
+  enginex_load : microcode load
+  enginex_leds : led mux control
+
+  cd /sys/class/leds/lp5523:channel2/device
+  echo "load" > engine3_mode
+  echo "9d80400004ff05ff437f0000" > engine3_load
+  echo "111111111" > engine3_leds
+  echo "run" > engine3_mode
+
+  To stop the engine:
+  echo "disabled" > engine3_mode
+
+2) Firmware interface - LP55xx common interface
+  For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+LP5523 has three master faders. If a channel is mapped to one of
+the master faders, its output is dimmed based on the value of the master
+fader.
+
+For example,
+
+  echo "123000123" > master_fader_leds
+
+creates the following channel-fader mappings:
+
+  channel 0,6 to master_fader1
+  channel 1,7 to master_fader2
+  channel 2,8 to master_fader3
+
+Then, to have 25% of the original output on channel 0,6:
+
+  echo 64 > master_fader1
+
+To have 0% of the original output (i.e. no output) channel 1,7:
+
+  echo 0 > master_fader2
+
+To have 100% of the original output (i.e. no dimming) on channel 2,8:
+
+  echo 255 > master_fader3
+
+To clear all master fader controls:
+
+  echo "000000000" > master_fader_leds
+
+Selftest uses always the current from the platform data.
+
+Each channel contains led current settings.
+/sys/class/leds/lp5523:channel2/led_current - RW
+/sys/class/leds/lp5523:channel2/max_current - RO
+Format: 10x mA i.e 10 means 1.0 mA
+
+Example platform data:
+
+Note - chan_nr can have values between 0 and 8.
+
+static struct lp55xx_led_config lp5523_led_config[] = {
+        {
+		.name		= "D1",
+                .chan_nr        = 0,
+                .led_current    = 50,
+		.max_current    = 130,
+        },
+...
+        {
+                .chan_nr        = 8,
+                .led_current    = 50,
+		.max_current    = 130,
+        }
+};
+
+static int lp5523_setup(void)
+{
+	/* Setup HW resources */
+}
+
+static void lp5523_release(void)
+{
+	/* Release HW resources */
+}
+
+static void lp5523_enable(bool state)
+{
+	/* Control chip enable signal */
+}
+
+static struct lp55xx_platform_data lp5523_platform_data = {
+        .led_config     = lp5523_led_config,
+        .num_channels   = ARRAY_SIZE(lp5523_led_config),
+        .clock_mode     = LP55XX_CLOCK_EXT,
+        .setup_resources   = lp5523_setup,
+        .release_resources = lp5523_release,
+        .enable            = lp5523_enable,
+};
diff --git a/src/kernel/linux/v4.14/Documentation/leds/leds-lp5562.txt b/src/kernel/linux/v4.14/Documentation/leds/leds-lp5562.txt
new file mode 100644
index 0000000..5a823ff
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/leds-lp5562.txt
@@ -0,0 +1,120 @@
+Kernel driver for LP5562
+========================
+
+* TI LP5562 LED Driver
+
+Author: Milo(Woogyom) Kim <milo.kim@ti.com>
+
+Description
+
+  LP5562 can drive up to 4 channels. R/G/B and White.
+  LEDs can be controlled directly via the led class control interface.
+
+  All four channels can be also controlled using the engine micro programs.
+  LP5562 has the internal program memory for running various LED patterns.
+  For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+Device attribute: engine_mux
+
+  3 Engines are allocated in LP5562, but the number of channel is 4.
+  Therefore each channel should be mapped to the engine number.
+  Value : RGB or W
+
+  This attribute is used for programming LED data with the firmware interface.
+  Unlike the LP5521/LP5523/55231, LP5562 has unique feature for the engine mux,
+  so additional sysfs is required.
+
+  LED Map
+  Red   ... Engine 1 (fixed)
+  Green ... Engine 2 (fixed)
+  Blue  ... Engine 3 (fixed)
+  White ... Engine 1 or 2 or 3 (selective)
+
+How to load the program data using engine_mux
+
+  Before loading the LP5562 program data, engine_mux should be written between
+  the engine selection and loading the firmware.
+  Engine mux has two different mode, RGB and W.
+  RGB is used for loading RGB program data, W is used for W program data.
+
+  For example, run blinking green channel pattern,
+  echo 2 > /sys/bus/i2c/devices/xxxx/select_engine     # 2 is for green channel
+  echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux    # engine mux for RGB
+  echo 1 > /sys/class/firmware/lp5562/loading
+  echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
+  echo 0 > /sys/class/firmware/lp5562/loading
+  echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+  To run a blinking white pattern,
+  echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine
+  echo "W" > /sys/bus/i2c/devices/xxxx/engine_mux
+  echo 1 > /sys/class/firmware/lp5562/loading
+  echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
+  echo 0 > /sys/class/firmware/lp5562/loading
+  echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+How to load the predefined patterns
+
+  Please refer to 'leds-lp55xx.txt"
+
+Setting Current of Each Channel
+
+  Like LP5521 and LP5523/55231, LP5562 provides LED current settings.
+  The 'led_current' and 'max_current' are used.
+
+(Example of Platform data)
+
+To configure the platform specific data, lp55xx_platform_data structure is used.
+
+static struct lp55xx_led_config lp5562_led_config[] = {
+	{
+		.name 		= "R",
+		.chan_nr	= 0,
+		.led_current	= 20,
+		.max_current	= 40,
+	},
+	{
+		.name 		= "G",
+		.chan_nr	= 1,
+		.led_current	= 20,
+		.max_current	= 40,
+	},
+	{
+		.name 		= "B",
+		.chan_nr	= 2,
+		.led_current	= 20,
+		.max_current	= 40,
+	},
+	{
+		.name 		= "W",
+		.chan_nr	= 3,
+		.led_current	= 20,
+		.max_current	= 40,
+	},
+};
+
+static int lp5562_setup(void)
+{
+	/* setup HW resources */
+}
+
+static void lp5562_release(void)
+{
+	/* Release HW resources */
+}
+
+static void lp5562_enable(bool state)
+{
+	/* Control of chip enable signal */
+}
+
+static struct lp55xx_platform_data lp5562_platform_data = {
+        .led_config     = lp5562_led_config,
+        .num_channels   = ARRAY_SIZE(lp5562_led_config),
+        .setup_resources   = lp5562_setup,
+        .release_resources = lp5562_release,
+        .enable            = lp5562_enable,
+};
+
+If the current is set to 0 in the platform data, that channel is
+disabled and it is not visible in the sysfs.
diff --git a/src/kernel/linux/v4.14/Documentation/leds/leds-lp55xx.txt b/src/kernel/linux/v4.14/Documentation/leds/leds-lp55xx.txt
new file mode 100644
index 0000000..e23fa91
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/leds-lp55xx.txt
@@ -0,0 +1,194 @@
+LP5521/LP5523/LP55231/LP5562/LP8501 Common Driver
+=================================================
+
+Authors: Milo(Woogyom) Kim <milo.kim@ti.com>
+
+Description
+-----------
+LP5521, LP5523/55231, LP5562 and LP8501 have common features as below.
+
+  Register access via the I2C
+  Device initialization/deinitialization
+  Create LED class devices for multiple output channels
+  Device attributes for user-space interface
+  Program memory for running LED patterns
+
+The LP55xx common driver provides these features using exported functions.
+  lp55xx_init_device() / lp55xx_deinit_device()
+  lp55xx_register_leds() / lp55xx_unregister_leds()
+  lp55xx_regsister_sysfs() / lp55xx_unregister_sysfs()
+
+( Driver Structure Data )
+
+In lp55xx common driver, two different data structure is used.
+
+o lp55xx_led
+  control multi output LED channels such as led current, channel index.
+o lp55xx_chip
+  general chip control such like the I2C and platform data.
+
+For example, LP5521 has maximum 3 LED channels.
+LP5523/55231 has 9 output channels.
+
+lp55xx_chip for LP5521 ... lp55xx_led #1
+                           lp55xx_led #2
+                           lp55xx_led #3
+
+lp55xx_chip for LP5523 ... lp55xx_led #1
+                           lp55xx_led #2
+                                 .
+                                 .
+                           lp55xx_led #9
+
+( Chip Dependent Code )
+
+To support device specific configurations, special structure
+'lpxx_device_config' is used.
+
+  Maximum number of channels
+  Reset command, chip enable command
+  Chip specific initialization
+  Brightness control register access
+  Setting LED output current
+  Program memory address access for running patterns
+  Additional device specific attributes
+
+( Firmware Interface )
+
+LP55xx family devices have the internal program memory for running
+various LED patterns.
+This pattern data is saved as a file in the user-land or
+hex byte string is written into the memory through the I2C.
+LP55xx common driver supports the firmware interface.
+
+LP55xx chips have three program engines.
+To load and run the pattern, the programming sequence is following.
+  (1) Select an engine number (1/2/3)
+  (2) Mode change to load
+  (3) Write pattern data into selected area
+  (4) Mode change to run
+
+The LP55xx common driver provides simple interfaces as below.
+select_engine : Select which engine is used for running program
+run_engine    : Start program which is loaded via the firmware interface
+firmware      : Load program data
+
+In case of LP5523, one more command is required, 'enginex_leds'.
+It is used for selecting LED output(s) at each engine number.
+In more details, please refer to 'leds-lp5523.txt'.
+
+For example, run blinking pattern in engine #1 of LP5521
+echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
+echo 1 > /sys/class/firmware/lp5521/loading
+echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
+echo 0 > /sys/class/firmware/lp5521/loading
+echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+For example, run blinking pattern in engine #3 of LP55231
+Two LEDs are configured as pattern output channels.
+echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
+echo 1 > /sys/class/firmware/lp55231/loading
+echo "9d0740ff7e0040007e00a0010000" > /sys/class/firmware/lp55231/data
+echo 0 > /sys/class/firmware/lp55231/loading
+echo "000001100" > /sys/bus/i2c/devices/xxxx/engine3_leds
+echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+To start blinking patterns in engine #2 and #3 simultaneously,
+for idx in 2 3
+do
+  echo $idx > /sys/class/leds/red/device/select_engine
+  sleep 0.1
+  echo 1 > /sys/class/firmware/lp5521/loading
+  echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
+  echo 0 > /sys/class/firmware/lp5521/loading
+done
+echo 1 > /sys/class/leds/red/device/run_engine
+
+Here is another example for LP5523.
+Full LED strings are selected by 'engine2_leds'.
+echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
+echo 1 > /sys/class/firmware/lp5523/loading
+echo "9d80400004ff05ff437f0000" > /sys/class/firmware/lp5523/data
+echo 0 > /sys/class/firmware/lp5523/loading
+echo "111111111" > /sys/bus/i2c/devices/xxxx/engine2_leds
+echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+As soon as 'loading' is set to 0, registered callback is called.
+Inside the callback, the selected engine is loaded and memory is updated.
+To run programmed pattern, 'run_engine' attribute should be enabled.
+
+The pattern sequence of LP8501 is similar to LP5523.
+However pattern data is specific.
+Ex 1) Engine 1 is used
+echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
+echo 1 > /sys/class/firmware/lp8501/loading
+echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+echo 0 > /sys/class/firmware/lp8501/loading
+echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+Ex 2) Engine 2 and 3 are used at the same time
+echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
+sleep 1
+echo 1 > /sys/class/firmware/lp8501/loading
+echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+echo 0 > /sys/class/firmware/lp8501/loading
+sleep 1
+echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
+sleep 1
+echo 1 > /sys/class/firmware/lp8501/loading
+echo "9d0340ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+echo 0 > /sys/class/firmware/lp8501/loading
+sleep 1
+echo 1 > /sys/class/leds/d1/device/run_engine
+
+( 'run_engine' and 'firmware_cb' )
+The sequence of running the program data is common.
+But each device has own specific register addresses for commands.
+To support this, 'run_engine' and 'firmware_cb' are configurable in each driver.
+run_engine  : Control the selected engine
+firmware_cb : The callback function after loading the firmware is done.
+              Chip specific commands for loading and updating program memory.
+
+( Predefined pattern data )
+
+Without the firmware interface, LP55xx driver provides another method for
+loading a LED pattern. That is 'predefined' pattern.
+A predefined pattern is defined in the platform data and load it(or them)
+via the sysfs if needed.
+To use the predefined pattern concept, 'patterns' and 'num_patterns' should be
+configured.
+
+  Example of predefined pattern data:
+
+  /* mode_1: blinking data */
+  static const u8 mode_1[] = {
+		0x40, 0x00, 0x60, 0x00, 0x40, 0xFF, 0x60, 0x00,
+		};
+
+  /* mode_2: always on */
+  static const u8 mode_2[] = { 0x40, 0xFF, };
+
+  struct lp55xx_predef_pattern board_led_patterns[] = {
+	{
+		.r = mode_1,
+		.size_r = ARRAY_SIZE(mode_1),
+	},
+	{
+		.b = mode_2,
+		.size_b = ARRAY_SIZE(mode_2),
+	},
+  }
+
+  struct lp55xx_platform_data lp5562_pdata = {
+  ...
+	.patterns      = board_led_patterns,
+	.num_patterns  = ARRAY_SIZE(board_led_patterns),
+  };
+
+Then, mode_1 and mode_2 can be run via through the sysfs.
+
+  echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern    # red blinking LED pattern
+  echo 2 > /sys/bus/i2c/devices/xxxx/led_pattern    # blue LED always on
+
+To stop running pattern,
+  echo 0 > /sys/bus/i2c/devices/xxxx/led_pattern
diff --git a/src/kernel/linux/v4.14/Documentation/leds/leds-mlxcpld.txt b/src/kernel/linux/v4.14/Documentation/leds/leds-mlxcpld.txt
new file mode 100644
index 0000000..a0e8fd4
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/leds-mlxcpld.txt
@@ -0,0 +1,110 @@
+Kernel driver for Mellanox systems LEDs
+=======================================
+
+Provide system LED support for the nex Mellanox systems:
+"msx6710", "msx6720", "msb7700", "msn2700", "msx1410",
+"msn2410", "msb7800", "msn2740", "msn2100".
+
+Description
+-----------
+Driver provides the following LEDs for the systems "msx6710", "msx6720",
+"msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740":
+  mlxcpld:fan1:green
+  mlxcpld:fan1:red
+  mlxcpld:fan2:green
+  mlxcpld:fan2:red
+  mlxcpld:fan3:green
+  mlxcpld:fan3:red
+  mlxcpld:fan4:green
+  mlxcpld:fan4:red
+  mlxcpld:psu:green
+  mlxcpld:psu:red
+  mlxcpld:status:green
+  mlxcpld:status:red
+
+ "status"
+  CPLD reg offset: 0x20
+  Bits [3:0]
+
+ "psu"
+  CPLD reg offset: 0x20
+  Bits [7:4]
+
+ "fan1"
+  CPLD reg offset: 0x21
+  Bits [3:0]
+
+ "fan2"
+  CPLD reg offset: 0x21
+  Bits [7:4]
+
+ "fan3"
+  CPLD reg offset: 0x22
+  Bits [3:0]
+
+ "fan4"
+  CPLD reg offset: 0x22
+  Bits [7:4]
+
+ Color mask for all the above LEDs:
+  [bit3,bit2,bit1,bit0] or
+  [bit7,bit6,bit5,bit4]:
+	[0,0,0,0] = LED OFF
+	[0,1,0,1] = Red static ON
+	[1,1,0,1] = Green static ON
+	[0,1,1,0] = Red blink 3Hz
+	[1,1,1,0] = Green blink 3Hz
+	[0,1,1,1] = Red blink 6Hz
+	[1,1,1,1] = Green blink 6Hz
+
+Driver provides the following LEDs for the system "msn2100":
+  mlxcpld:fan:green
+  mlxcpld:fan:red
+  mlxcpld:psu1:green
+  mlxcpld:psu1:red
+  mlxcpld:psu2:green
+  mlxcpld:psu2:red
+  mlxcpld:status:green
+  mlxcpld:status:red
+  mlxcpld:uid:blue
+
+ "status"
+  CPLD reg offset: 0x20
+  Bits [3:0]
+
+ "fan"
+  CPLD reg offset: 0x21
+  Bits [3:0]
+
+ "psu1"
+  CPLD reg offset: 0x23
+  Bits [3:0]
+
+ "psu2"
+  CPLD reg offset: 0x23
+  Bits [7:4]
+
+ "uid"
+  CPLD reg offset: 0x24
+  Bits [3:0]
+
+ Color mask for all the above LEDs, excepted uid:
+  [bit3,bit2,bit1,bit0] or
+  [bit7,bit6,bit5,bit4]:
+	[0,0,0,0] = LED OFF
+	[0,1,0,1] = Red static ON
+	[1,1,0,1] = Green static ON
+	[0,1,1,0] = Red blink 3Hz
+	[1,1,1,0] = Green blink 3Hz
+	[0,1,1,1] = Red blink 6Hz
+	[1,1,1,1] = Green blink 6Hz
+
+ Color mask for uid LED:
+  [bit3,bit2,bit1,bit0]:
+	[0,0,0,0] = LED OFF
+	[1,1,0,1] = Blue static ON
+	[1,1,1,0] = Blue blink 3Hz
+	[1,1,1,1] = Blue blink 6Hz
+
+Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle).
+For 3Hz duty cylce is about 167 msec, for 6Hz is about 83 msec.
diff --git a/src/kernel/linux/v4.14/Documentation/leds/ledtrig-oneshot.txt b/src/kernel/linux/v4.14/Documentation/leds/ledtrig-oneshot.txt
new file mode 100644
index 0000000..fe57474
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/ledtrig-oneshot.txt
@@ -0,0 +1,43 @@
+One-shot LED Trigger
+====================
+
+This is a LED trigger useful for signaling the user of an event where there are
+no clear trap points to put standard led-on and led-off settings.  Using this
+trigger, the application needs only to signal the trigger when an event has
+happened, than the trigger turns the LED on and than keeps it off for a
+specified amount of time.
+
+This trigger is meant to be usable both for sporadic and dense events.  In the
+first case, the trigger produces a clear single controlled blink for each
+event, while in the latter it keeps blinking at constant rate, as to signal
+that the events are arriving continuously.
+
+A one-shot LED only stays in a constant state when there are no events.  An
+additional "invert" property specifies if the LED has to stay off (normal) or
+on (inverted) when not rearmed.
+
+The trigger can be activated from user space on led class devices as shown
+below:
+
+  echo oneshot > trigger
+
+This adds sysfs attributes to the LED that are documented in:
+Documentation/ABI/testing/sysfs-class-led-trigger-oneshot
+
+Example use-case: network devices, initialization:
+
+  echo oneshot > trigger # set trigger for this led
+  echo 33 > delay_on     # blink at 1 / (33 + 33) Hz on continuous traffic
+  echo 33 > delay_off
+
+interface goes up:
+
+  echo 1 > invert # set led as normally-on, turn the led on
+
+packet received/transmitted:
+
+  echo 1 > shot # led starts blinking, ignored if already blinking
+
+interface goes down
+
+  echo 0 > invert # set led as normally-off, turn the led off
diff --git a/src/kernel/linux/v4.14/Documentation/leds/ledtrig-transient.txt b/src/kernel/linux/v4.14/Documentation/leds/ledtrig-transient.txt
new file mode 100644
index 0000000..3bd38b4
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/ledtrig-transient.txt
@@ -0,0 +1,152 @@
+LED Transient Trigger
+=====================
+
+The leds timer trigger does not currently have an interface to activate
+a one shot timer. The current support allows for setting two timers, one for
+specifying how long a state to be on, and the second for how long the state
+to be off. The delay_on value specifies the time period an LED should stay
+in on state, followed by a delay_off value that specifies how long the LED
+should stay in off state. The on and off cycle repeats until the trigger
+gets deactivated. There is no provision for one time activation to implement
+features that require an on or off state to be held just once and then stay in
+the original state forever.
+
+Without one shot timer interface, user space can still use timer trigger to
+set a timer to hold a state, however when user space application crashes or
+goes away without deactivating the timer, the hardware will be left in that
+state permanently.
+
+As a specific example of this use-case, let's look at vibrate feature on
+phones. Vibrate function on phones is implemented using PWM pins on SoC or
+PMIC. There is a need to activate one shot timer to control the vibrate
+feature, to prevent user space crashes leaving the phone in vibrate mode
+permanently causing the battery to drain.
+
+Transient trigger addresses the need for one shot timer activation. The
+transient trigger can be enabled and disabled just like the other leds
+triggers.
+
+When an led class device driver registers itself, it can specify all leds
+triggers it supports and a default trigger. During registration, activation
+routine for the default trigger gets called. During registration of an led
+class device, the LED state does not change.
+
+When the driver unregisters, deactivation routine for the currently active
+trigger will be called, and LED state is changed to LED_OFF.
+
+Driver suspend changes the LED state to LED_OFF and resume doesn't change
+the state. Please note that there is no explicit interaction between the
+suspend and resume actions and the currently enabled trigger. LED state
+changes are suspended while the driver is in suspend state. Any timers
+that are active at the time driver gets suspended, continue to run, without
+being able to actually change the LED state. Once driver is resumed, triggers
+start functioning again.
+
+LED state changes are controlled using brightness which is a common led
+class device property. When brightness is set to 0 from user space via
+echo 0 > brightness, it will result in deactivating the current trigger.
+
+Transient trigger uses standard register and unregister interfaces. During
+trigger registration, for each led class device that specifies this trigger
+as its default trigger, trigger activation routine will get called. During
+registration, the LED state does not change, unless there is another trigger
+active, in which case LED state changes to LED_OFF.
+
+During trigger unregistration, LED state gets changed to LED_OFF.
+
+Transient trigger activation routine doesn't change the LED state. It
+creates its properties and does its initialization. Transient trigger
+deactivation routine, will cancel any timer that is active before it cleans
+up and removes the properties it created. It will restore the LED state to
+non-transient state. When driver gets suspended, irrespective of the transient
+state, the LED state changes to LED_OFF.
+
+Transient trigger can be enabled and disabled from user space on led class
+devices, that support this trigger as shown below:
+
+echo transient > trigger
+echo none > trigger
+
+NOTE: Add a new property trigger state to control the state.
+
+This trigger exports three properties, activate, state, and duration. When
+transient trigger is activated these properties are set to default values.
+
+- duration allows setting timer value in msecs. The initial value is 0.
+- activate allows activating and deactivating the timer specified by
+  duration as needed. The initial and default value is 0.  This will allow
+  duration to be set after trigger activation.
+- state allows user to specify a transient state to be held for the specified
+  duration.
+
+	activate - one shot timer activate mechanism.
+		1 when activated, 0 when deactivated.
+		default value is zero when transient trigger is enabled,
+		to allow duration to be set.
+
+		activate state indicates a timer with a value of specified
+		duration running.
+		deactivated state indicates that there is no active timer
+		running.
+
+	duration - one shot timer value. When activate is set, duration value
+		is used to start a timer that runs once. This value doesn't
+		get changed by the trigger unless user does a set via
+		echo new_value > duration
+
+	state - transient state to be held. It has two values 0 or 1. 0 maps
+		to LED_OFF and 1 maps to LED_FULL. The specified state is
+		held for the duration of the one shot timer and then the
+		state gets changed to the non-transient state which is the
+		inverse of transient state.
+		If state = LED_FULL, when the timer runs out the state will
+		go back to LED_OFF.
+		If state = LED_OFF, when the timer runs out the state will
+		go back to LED_FULL.
+		Please note that current LED state is not checked prior to
+		changing the state to the specified state.
+		Driver could map these values to inverted depending on the
+		default states it defines for the LED in its brightness_set()
+		interface which is called from the led brightness_set()
+		interfaces to control the LED state.
+
+When timer expires activate goes back to deactivated state, duration is left
+at the set value to be used when activate is set at a future time. This will
+allow user app to set the time once and activate it to run it once for the
+specified value as needed. When timer expires, state is restored to the
+non-transient state which is the inverse of the transient state.
+
+	echo 1 > activate - starts timer = duration when duration is not 0.
+	echo 0 > activate - cancels currently running timer.
+	echo n > duration - stores timer value to be used upon next
+                            activate. Currently active timer if
+                            any, continues to run for the specified time.
+	echo 0 > duration - stores timer value to be used upon next
+                            activate. Currently active timer if any,
+                            continues to run for the specified time.
+	echo 1 > state    - stores desired transient state LED_FULL to be
+			    held for the specified duration.
+	echo 0 > state    - stores desired transient state LED_OFF to be
+			    held for the specified duration.
+
+What is not supported:
+======================
+- Timer activation is one shot and extending and/or shortening the timer
+  is not supported.
+
+Example use-case 1:
+	echo transient > trigger
+	echo n > duration
+	echo 1 > state
+repeat the following step as needed:
+	echo 1 > activate - start timer = duration to run once
+	echo 1 > activate - start timer = duration to run once
+	echo none > trigger
+
+This trigger is intended to be used for for the following example use cases:
+ - Control of vibrate (phones, tablets etc.) hardware by user space app.
+ - Use of LED by user space app as activity indicator.
+ - Use of LED by user space app as a kind of watchdog indicator -- as
+       long as the app is alive, it can keep the LED illuminated, if it dies
+       the LED will be extinguished automatically.
+ - Use by any user space app that needs a transient GPIO output.
diff --git a/src/kernel/linux/v4.14/Documentation/leds/ledtrig-usbport.txt b/src/kernel/linux/v4.14/Documentation/leds/ledtrig-usbport.txt
new file mode 100644
index 0000000..69f54bf
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/ledtrig-usbport.txt
@@ -0,0 +1,41 @@
+USB port LED trigger
+====================
+
+This LED trigger can be used for signalling to the user a presence of USB device
+in a given port. It simply turns on LED when device appears and turns it off
+when it disappears.
+
+It requires selecting USB ports that should be observed. All available ones are
+listed as separated entries in a "ports" subdirectory. Selecting is handled by
+echoing "1" to a chosen port.
+
+Please note that this trigger allows selecting multiple USB ports for a single
+LED. This can be useful in two cases:
+
+1) Device with single USB LED and few physical ports
+
+In such a case LED will be turned on as long as there is at least one connected
+USB device.
+
+2) Device with a physical port handled by few controllers
+
+Some devices may have one controller per PHY standard. E.g. USB 3.0 physical
+port may be handled by ohci-platform, ehci-platform and xhci-hcd. If there is
+only one LED user will most likely want to assign ports from all 3 hubs.
+
+
+This trigger can be activated from user space on led class devices as shown
+below:
+
+  echo usbport > trigger
+
+This adds sysfs attributes to the LED that are documented in:
+Documentation/ABI/testing/sysfs-class-led-trigger-usbport
+
+Example use-case:
+
+  echo usbport > trigger
+  echo 1 > ports/usb1-port1
+  echo 1 > ports/usb2-port1
+  cat ports/usb1-port1
+  echo 0 > ports/usb1-port1
diff --git a/src/kernel/linux/v4.14/Documentation/leds/uleds.txt b/src/kernel/linux/v4.14/Documentation/leds/uleds.txt
new file mode 100644
index 0000000..13e375a
--- /dev/null
+++ b/src/kernel/linux/v4.14/Documentation/leds/uleds.txt
@@ -0,0 +1,36 @@
+Userspace LEDs
+==============
+
+The uleds driver supports userspace LEDs. This can be useful for testing
+triggers and can also be used to implement virtual LEDs.
+
+
+Usage
+=====
+
+When the driver is loaded, a character device is created at /dev/uleds. To
+create a new LED class device, open /dev/uleds and write a uleds_user_dev
+structure to it (found in kernel public header file linux/uleds.h).
+
+    #define LED_MAX_NAME_SIZE 64
+
+    struct uleds_user_dev {
+        char name[LED_MAX_NAME_SIZE];
+    };
+
+A new LED class device will be created with the name given. The name can be
+any valid sysfs device node name, but consider using the LED class naming
+convention of "devicename:color:function".
+
+The current brightness is found by reading a single byte from the character
+device. Values are unsigned: 0 to 255. Reading will block until the brightness
+changes. The device node can also be polled to notify when the brightness value
+changes.
+
+The LED class device will be removed when the open file handle to /dev/uleds
+is closed.
+
+Multiple LED class devices are created by opening additional file handles to
+/dev/uleds.
+
+See tools/leds/uledmon.c for an example userspace program.