[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/arch/arm/mach-ixp4xx/dsmg600-setup.c b/src/kernel/linux/v4.14/arch/arm/mach-ixp4xx/dsmg600-setup.c
new file mode 100644
index 0000000..db488ec
--- /dev/null
+++ b/src/kernel/linux/v4.14/arch/arm/mach-ixp4xx/dsmg600-setup.c
@@ -0,0 +1,299 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * DSM-G600 board-setup
+ *
+ * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
+ * Copyright (C) 2006 Tower Technologies
+ *
+ * based on ixdp425-setup.c:
+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
+ * based on nslu2-power.c:
+ * Copyright (C) 2005 Tower Technologies
+ * based on nslu2-io.c:
+ * Copyright (C) 2004 Karen Spearel
+ *
+ * Author: Alessandro Zummo <a.zummo@towertech.it>
+ * Author: Michael Westerhof <mwester@dls.net>
+ * Author: Rod Whitby <rod@whitby.id.au>
+ * Maintainers: http://www.nslu2-linux.org/
+ */
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <linux/jiffies.h>
+#include <linux/timer.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/leds.h>
+#include <linux/reboot.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+
+#include <mach/hardware.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+#include <asm/mach/time.h>
+
+#define DSMG600_SDA_PIN 5
+#define DSMG600_SCL_PIN 4
+
+/* DSM-G600 Timer Setting */
+#define DSMG600_FREQ 66000000
+
+/* Buttons */
+#define DSMG600_PB_GPIO 15 /* power button */
+#define DSMG600_RB_GPIO 3 /* reset button */
+
+/* Power control */
+#define DSMG600_PO_GPIO 2 /* power off */
+
+/* LEDs */
+#define DSMG600_LED_PWR_GPIO 0
+#define DSMG600_LED_WLAN_GPIO 14
+
+static struct flash_platform_data dsmg600_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource dsmg600_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device dsmg600_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev.platform_data = &dsmg600_flash_data,
+ .num_resources = 1,
+ .resource = &dsmg600_flash_resource,
+};
+
+static struct i2c_gpio_platform_data dsmg600_i2c_gpio_data = {
+ .sda_pin = DSMG600_SDA_PIN,
+ .scl_pin = DSMG600_SCL_PIN,
+};
+
+static struct platform_device dsmg600_i2c_gpio = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &dsmg600_i2c_gpio_data,
+ },
+};
+
+static struct i2c_board_info __initdata dsmg600_i2c_board_info [] = {
+ {
+ I2C_BOARD_INFO("pcf8563", 0x51),
+ },
+};
+
+static struct gpio_led dsmg600_led_pins[] = {
+ {
+ .name = "dsmg600:green:power",
+ .gpio = DSMG600_LED_PWR_GPIO,
+ },
+ {
+ .name = "dsmg600:green:wlan",
+ .gpio = DSMG600_LED_WLAN_GPIO,
+ .active_low = true,
+ },
+};
+
+static struct gpio_led_platform_data dsmg600_led_data = {
+ .num_leds = ARRAY_SIZE(dsmg600_led_pins),
+ .leds = dsmg600_led_pins,
+};
+
+static struct platform_device dsmg600_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev.platform_data = &dsmg600_led_data,
+};
+
+static struct resource dsmg600_uart_resources[] = {
+ {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
+static struct plat_serial8250_port dsmg600_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { }
+};
+
+static struct platform_device dsmg600_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev.platform_data = dsmg600_uart_data,
+ .num_resources = ARRAY_SIZE(dsmg600_uart_resources),
+ .resource = dsmg600_uart_resources,
+};
+
+static struct platform_device *dsmg600_devices[] __initdata = {
+ &dsmg600_i2c_gpio,
+ &dsmg600_flash,
+ &dsmg600_leds,
+};
+
+static void dsmg600_power_off(void)
+{
+ /* enable the pwr cntl and drive it high */
+ gpio_direction_output(DSMG600_PO_GPIO, 1);
+}
+
+/* This is used to make sure the power-button pusher is serious. The button
+ * must be held until the value of this counter reaches zero.
+ */
+static int power_button_countdown;
+
+/* Must hold the button down for at least this many counts to be processed */
+#define PBUTTON_HOLDDOWN_COUNT 4 /* 2 secs */
+
+static void dsmg600_power_handler(unsigned long data);
+static DEFINE_TIMER(dsmg600_power_timer, dsmg600_power_handler, 0, 0);
+
+static void dsmg600_power_handler(unsigned long data)
+{
+ /* This routine is called twice per second to check the
+ * state of the power button.
+ */
+
+ if (gpio_get_value(DSMG600_PB_GPIO)) {
+
+ /* IO Pin is 1 (button pushed) */
+ if (power_button_countdown > 0)
+ power_button_countdown--;
+
+ } else {
+
+ /* Done on button release, to allow for auto-power-on mods. */
+ if (power_button_countdown == 0) {
+ /* Signal init to do the ctrlaltdel action,
+ * this will bypass init if it hasn't started
+ * and do a kernel_restart.
+ */
+ ctrl_alt_del();
+
+ /* Change the state of the power LED to "blink" */
+ gpio_set_value(DSMG600_LED_PWR_GPIO, 0);
+ } else {
+ power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+ }
+ }
+
+ mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
+}
+
+static irqreturn_t dsmg600_reset_handler(int irq, void *dev_id)
+{
+ /* This is the paper-clip reset, it shuts the machine down directly. */
+ machine_power_off();
+
+ return IRQ_HANDLED;
+}
+
+static void __init dsmg600_timer_init(void)
+{
+ /* The xtal on this machine is non-standard. */
+ ixp4xx_timer_freq = DSMG600_FREQ;
+
+ /* Call standard timer_init function. */
+ ixp4xx_timer_init();
+}
+
+static int __init dsmg600_gpio_init(void)
+{
+ if (!machine_is_dsmg600())
+ return 0;
+
+ gpio_request(DSMG600_RB_GPIO, "reset button");
+ if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
+ IRQF_TRIGGER_LOW, "DSM-G600 reset button", NULL) < 0) {
+
+ printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
+ gpio_to_irq(DSMG600_RB_GPIO));
+ }
+
+ /*
+ * The power button on the D-Link DSM-G600 is on GPIO 15, but
+ * it cannot handle interrupts on that GPIO line. So we'll
+ * have to poll it with a kernel timer.
+ */
+
+ /* Make sure that the power button GPIO is set up as an input */
+ gpio_request(DSMG600_PB_GPIO, "power button");
+ gpio_direction_input(DSMG600_PB_GPIO);
+ /* Request poweroff GPIO line */
+ gpio_request(DSMG600_PO_GPIO, "power off button");
+
+ /* Set the initial value for the power button IRQ handler */
+ power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+
+ mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
+ return 0;
+}
+device_initcall(dsmg600_gpio_init);
+
+static void __init dsmg600_init(void)
+{
+ ixp4xx_sys_init();
+
+ /* Make sure that GPIO14 and GPIO15 are not used as clocks */
+ *IXP4XX_GPIO_GPCLKR = 0;
+
+ dsmg600_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ dsmg600_flash_resource.end =
+ IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
+
+ i2c_register_board_info(0, dsmg600_i2c_board_info,
+ ARRAY_SIZE(dsmg600_i2c_board_info));
+
+ /* The UART is required on the DSM-G600 (Redboot cannot use the
+ * NIC) -- do it here so that it does *not* get removed if
+ * platform_add_devices fails!
+ */
+ (void)platform_device_register(&dsmg600_uart);
+
+ platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices));
+
+ pm_power_off = dsmg600_power_off;
+}
+
+MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")
+ /* Maintainer: www.nslu2-linux.org */
+ .atag_offset = 0x100,
+ .map_io = ixp4xx_map_io,
+ .init_early = ixp4xx_init_early,
+ .init_irq = ixp4xx_init_irq,
+ .init_time = dsmg600_timer_init,
+ .init_machine = dsmg600_init,
+#if defined(CONFIG_PCI)
+ .dma_zone_size = SZ_64M,
+#endif
+ .restart = ixp4xx_restart,
+MACHINE_END