[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/arch/arm/plat-pxa/Kconfig b/src/kernel/linux/v4.14/arch/arm/plat-pxa/Kconfig
new file mode 100644
index 0000000..da53395
--- /dev/null
+++ b/src/kernel/linux/v4.14/arch/arm/plat-pxa/Kconfig
@@ -0,0 +1,8 @@
+if PLAT_PXA
+
+config PXA_SSP
+ tristate
+ help
+ Enable support for PXA2xx SSP ports
+
+endif
diff --git a/src/kernel/linux/v4.14/arch/arm/plat-pxa/Makefile b/src/kernel/linux/v4.14/arch/arm/plat-pxa/Makefile
new file mode 100644
index 0000000..2f06a2e
--- /dev/null
+++ b/src/kernel/linux/v4.14/arch/arm/plat-pxa/Makefile
@@ -0,0 +1,9 @@
+#
+# Makefile for code common across different PXA processor families
+#
+ccflags-$(CONFIG_ARCH_MMP) := -I$(srctree)/$(src)/include
+
+obj-$(CONFIG_PXA3xx) += mfp.o
+obj-$(CONFIG_ARCH_MMP) += mfp.o
+
+obj-$(CONFIG_PXA_SSP) += ssp.o
diff --git a/src/kernel/linux/v4.14/arch/arm/plat-pxa/include/plat/mfp.h b/src/kernel/linux/v4.14/arch/arm/plat-pxa/include/plat/mfp.h
new file mode 100644
index 0000000..10bc4f3
--- /dev/null
+++ b/src/kernel/linux/v4.14/arch/arm/plat-pxa/include/plat/mfp.h
@@ -0,0 +1,475 @@
+/*
+ * arch/arm/plat-pxa/include/plat/mfp.h
+ *
+ * Common Multi-Function Pin Definitions
+ *
+ * Copyright (C) 2007 Marvell International Ltd.
+ *
+ * 2007-8-21: eric miao <eric.miao@marvell.com>
+ * initial version
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_PLAT_MFP_H
+#define __ASM_PLAT_MFP_H
+
+#define mfp_to_gpio(m) ((m) % 256)
+
+/* list of all the configurable MFP pins */
+enum {
+ MFP_PIN_INVALID = -1,
+
+ MFP_PIN_GPIO0 = 0,
+ MFP_PIN_GPIO1,
+ MFP_PIN_GPIO2,
+ MFP_PIN_GPIO3,
+ MFP_PIN_GPIO4,
+ MFP_PIN_GPIO5,
+ MFP_PIN_GPIO6,
+ MFP_PIN_GPIO7,
+ MFP_PIN_GPIO8,
+ MFP_PIN_GPIO9,
+ MFP_PIN_GPIO10,
+ MFP_PIN_GPIO11,
+ MFP_PIN_GPIO12,
+ MFP_PIN_GPIO13,
+ MFP_PIN_GPIO14,
+ MFP_PIN_GPIO15,
+ MFP_PIN_GPIO16,
+ MFP_PIN_GPIO17,
+ MFP_PIN_GPIO18,
+ MFP_PIN_GPIO19,
+ MFP_PIN_GPIO20,
+ MFP_PIN_GPIO21,
+ MFP_PIN_GPIO22,
+ MFP_PIN_GPIO23,
+ MFP_PIN_GPIO24,
+ MFP_PIN_GPIO25,
+ MFP_PIN_GPIO26,
+ MFP_PIN_GPIO27,
+ MFP_PIN_GPIO28,
+ MFP_PIN_GPIO29,
+ MFP_PIN_GPIO30,
+ MFP_PIN_GPIO31,
+ MFP_PIN_GPIO32,
+ MFP_PIN_GPIO33,
+ MFP_PIN_GPIO34,
+ MFP_PIN_GPIO35,
+ MFP_PIN_GPIO36,
+ MFP_PIN_GPIO37,
+ MFP_PIN_GPIO38,
+ MFP_PIN_GPIO39,
+ MFP_PIN_GPIO40,
+ MFP_PIN_GPIO41,
+ MFP_PIN_GPIO42,
+ MFP_PIN_GPIO43,
+ MFP_PIN_GPIO44,
+ MFP_PIN_GPIO45,
+ MFP_PIN_GPIO46,
+ MFP_PIN_GPIO47,
+ MFP_PIN_GPIO48,
+ MFP_PIN_GPIO49,
+ MFP_PIN_GPIO50,
+ MFP_PIN_GPIO51,
+ MFP_PIN_GPIO52,
+ MFP_PIN_GPIO53,
+ MFP_PIN_GPIO54,
+ MFP_PIN_GPIO55,
+ MFP_PIN_GPIO56,
+ MFP_PIN_GPIO57,
+ MFP_PIN_GPIO58,
+ MFP_PIN_GPIO59,
+ MFP_PIN_GPIO60,
+ MFP_PIN_GPIO61,
+ MFP_PIN_GPIO62,
+ MFP_PIN_GPIO63,
+ MFP_PIN_GPIO64,
+ MFP_PIN_GPIO65,
+ MFP_PIN_GPIO66,
+ MFP_PIN_GPIO67,
+ MFP_PIN_GPIO68,
+ MFP_PIN_GPIO69,
+ MFP_PIN_GPIO70,
+ MFP_PIN_GPIO71,
+ MFP_PIN_GPIO72,
+ MFP_PIN_GPIO73,
+ MFP_PIN_GPIO74,
+ MFP_PIN_GPIO75,
+ MFP_PIN_GPIO76,
+ MFP_PIN_GPIO77,
+ MFP_PIN_GPIO78,
+ MFP_PIN_GPIO79,
+ MFP_PIN_GPIO80,
+ MFP_PIN_GPIO81,
+ MFP_PIN_GPIO82,
+ MFP_PIN_GPIO83,
+ MFP_PIN_GPIO84,
+ MFP_PIN_GPIO85,
+ MFP_PIN_GPIO86,
+ MFP_PIN_GPIO87,
+ MFP_PIN_GPIO88,
+ MFP_PIN_GPIO89,
+ MFP_PIN_GPIO90,
+ MFP_PIN_GPIO91,
+ MFP_PIN_GPIO92,
+ MFP_PIN_GPIO93,
+ MFP_PIN_GPIO94,
+ MFP_PIN_GPIO95,
+ MFP_PIN_GPIO96,
+ MFP_PIN_GPIO97,
+ MFP_PIN_GPIO98,
+ MFP_PIN_GPIO99,
+ MFP_PIN_GPIO100,
+ MFP_PIN_GPIO101,
+ MFP_PIN_GPIO102,
+ MFP_PIN_GPIO103,
+ MFP_PIN_GPIO104,
+ MFP_PIN_GPIO105,
+ MFP_PIN_GPIO106,
+ MFP_PIN_GPIO107,
+ MFP_PIN_GPIO108,
+ MFP_PIN_GPIO109,
+ MFP_PIN_GPIO110,
+ MFP_PIN_GPIO111,
+ MFP_PIN_GPIO112,
+ MFP_PIN_GPIO113,
+ MFP_PIN_GPIO114,
+ MFP_PIN_GPIO115,
+ MFP_PIN_GPIO116,
+ MFP_PIN_GPIO117,
+ MFP_PIN_GPIO118,
+ MFP_PIN_GPIO119,
+ MFP_PIN_GPIO120,
+ MFP_PIN_GPIO121,
+ MFP_PIN_GPIO122,
+ MFP_PIN_GPIO123,
+ MFP_PIN_GPIO124,
+ MFP_PIN_GPIO125,
+ MFP_PIN_GPIO126,
+ MFP_PIN_GPIO127,
+
+ MFP_PIN_GPIO128,
+ MFP_PIN_GPIO129,
+ MFP_PIN_GPIO130,
+ MFP_PIN_GPIO131,
+ MFP_PIN_GPIO132,
+ MFP_PIN_GPIO133,
+ MFP_PIN_GPIO134,
+ MFP_PIN_GPIO135,
+ MFP_PIN_GPIO136,
+ MFP_PIN_GPIO137,
+ MFP_PIN_GPIO138,
+ MFP_PIN_GPIO139,
+ MFP_PIN_GPIO140,
+ MFP_PIN_GPIO141,
+ MFP_PIN_GPIO142,
+ MFP_PIN_GPIO143,
+ MFP_PIN_GPIO144,
+ MFP_PIN_GPIO145,
+ MFP_PIN_GPIO146,
+ MFP_PIN_GPIO147,
+ MFP_PIN_GPIO148,
+ MFP_PIN_GPIO149,
+ MFP_PIN_GPIO150,
+ MFP_PIN_GPIO151,
+ MFP_PIN_GPIO152,
+ MFP_PIN_GPIO153,
+ MFP_PIN_GPIO154,
+ MFP_PIN_GPIO155,
+ MFP_PIN_GPIO156,
+ MFP_PIN_GPIO157,
+ MFP_PIN_GPIO158,
+ MFP_PIN_GPIO159,
+ MFP_PIN_GPIO160,
+ MFP_PIN_GPIO161,
+ MFP_PIN_GPIO162,
+ MFP_PIN_GPIO163,
+ MFP_PIN_GPIO164,
+ MFP_PIN_GPIO165,
+ MFP_PIN_GPIO166,
+ MFP_PIN_GPIO167,
+ MFP_PIN_GPIO168,
+ MFP_PIN_GPIO169,
+ MFP_PIN_GPIO170,
+ MFP_PIN_GPIO171,
+ MFP_PIN_GPIO172,
+ MFP_PIN_GPIO173,
+ MFP_PIN_GPIO174,
+ MFP_PIN_GPIO175,
+ MFP_PIN_GPIO176,
+ MFP_PIN_GPIO177,
+ MFP_PIN_GPIO178,
+ MFP_PIN_GPIO179,
+ MFP_PIN_GPIO180,
+ MFP_PIN_GPIO181,
+ MFP_PIN_GPIO182,
+ MFP_PIN_GPIO183,
+ MFP_PIN_GPIO184,
+ MFP_PIN_GPIO185,
+ MFP_PIN_GPIO186,
+ MFP_PIN_GPIO187,
+ MFP_PIN_GPIO188,
+ MFP_PIN_GPIO189,
+ MFP_PIN_GPIO190,
+ MFP_PIN_GPIO191,
+
+ MFP_PIN_GPIO255 = 255,
+
+ MFP_PIN_GPIO0_2,
+ MFP_PIN_GPIO1_2,
+ MFP_PIN_GPIO2_2,
+ MFP_PIN_GPIO3_2,
+ MFP_PIN_GPIO4_2,
+ MFP_PIN_GPIO5_2,
+ MFP_PIN_GPIO6_2,
+ MFP_PIN_GPIO7_2,
+ MFP_PIN_GPIO8_2,
+ MFP_PIN_GPIO9_2,
+ MFP_PIN_GPIO10_2,
+ MFP_PIN_GPIO11_2,
+ MFP_PIN_GPIO12_2,
+ MFP_PIN_GPIO13_2,
+ MFP_PIN_GPIO14_2,
+ MFP_PIN_GPIO15_2,
+ MFP_PIN_GPIO16_2,
+ MFP_PIN_GPIO17_2,
+
+ MFP_PIN_ULPI_STP,
+ MFP_PIN_ULPI_NXT,
+ MFP_PIN_ULPI_DIR,
+
+ MFP_PIN_nXCVREN,
+ MFP_PIN_DF_CLE_nOE,
+ MFP_PIN_DF_nADV1_ALE,
+ MFP_PIN_DF_SCLK_E,
+ MFP_PIN_DF_SCLK_S,
+ MFP_PIN_nBE0,
+ MFP_PIN_nBE1,
+ MFP_PIN_DF_nADV2_ALE,
+ MFP_PIN_DF_INT_RnB,
+ MFP_PIN_DF_nCS0,
+ MFP_PIN_DF_nCS1,
+ MFP_PIN_nLUA,
+ MFP_PIN_nLLA,
+ MFP_PIN_DF_nWE,
+ MFP_PIN_DF_ALE_nWE,
+ MFP_PIN_DF_nRE_nOE,
+ MFP_PIN_DF_ADDR0,
+ MFP_PIN_DF_ADDR1,
+ MFP_PIN_DF_ADDR2,
+ MFP_PIN_DF_ADDR3,
+ MFP_PIN_DF_IO0,
+ MFP_PIN_DF_IO1,
+ MFP_PIN_DF_IO2,
+ MFP_PIN_DF_IO3,
+ MFP_PIN_DF_IO4,
+ MFP_PIN_DF_IO5,
+ MFP_PIN_DF_IO6,
+ MFP_PIN_DF_IO7,
+ MFP_PIN_DF_IO8,
+ MFP_PIN_DF_IO9,
+ MFP_PIN_DF_IO10,
+ MFP_PIN_DF_IO11,
+ MFP_PIN_DF_IO12,
+ MFP_PIN_DF_IO13,
+ MFP_PIN_DF_IO14,
+ MFP_PIN_DF_IO15,
+ MFP_PIN_DF_nCS0_SM_nCS2,
+ MFP_PIN_DF_nCS1_SM_nCS3,
+ MFP_PIN_SM_nCS0,
+ MFP_PIN_SM_nCS1,
+ MFP_PIN_DF_WEn,
+ MFP_PIN_DF_REn,
+ MFP_PIN_DF_CLE_SM_OEn,
+ MFP_PIN_DF_ALE_SM_WEn,
+ MFP_PIN_DF_RDY0,
+ MFP_PIN_DF_RDY1,
+
+ MFP_PIN_SM_SCLK,
+ MFP_PIN_SM_BE0,
+ MFP_PIN_SM_BE1,
+ MFP_PIN_SM_ADV,
+ MFP_PIN_SM_ADVMUX,
+ MFP_PIN_SM_RDY,
+
+ MFP_PIN_MMC1_DAT7,
+ MFP_PIN_MMC1_DAT6,
+ MFP_PIN_MMC1_DAT5,
+ MFP_PIN_MMC1_DAT4,
+ MFP_PIN_MMC1_DAT3,
+ MFP_PIN_MMC1_DAT2,
+ MFP_PIN_MMC1_DAT1,
+ MFP_PIN_MMC1_DAT0,
+ MFP_PIN_MMC1_CMD,
+ MFP_PIN_MMC1_CLK,
+ MFP_PIN_MMC1_CD,
+ MFP_PIN_MMC1_WP,
+
+ /* additional pins on PXA930 */
+ MFP_PIN_GSIM_UIO,
+ MFP_PIN_GSIM_UCLK,
+ MFP_PIN_GSIM_UDET,
+ MFP_PIN_GSIM_nURST,
+ MFP_PIN_PMIC_INT,
+ MFP_PIN_RDY,
+
+ /* additional pins on MMP2 */
+ MFP_PIN_TWSI1_SCL,
+ MFP_PIN_TWSI1_SDA,
+ MFP_PIN_TWSI4_SCL,
+ MFP_PIN_TWSI4_SDA,
+ MFP_PIN_CLK_REQ,
+
+ MFP_PIN_MAX,
+};
+
+/*
+ * a possible MFP configuration is represented by a 32-bit integer
+ *
+ * bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
+ * bit 10..12 - Alternate Function Selection
+ * bit 13..15 - Drive Strength
+ * bit 16..18 - Low Power Mode State
+ * bit 19..20 - Low Power Mode Edge Detection
+ * bit 21..22 - Run Mode Pull State
+ *
+ * to facilitate the definition, the following macros are provided
+ *
+ * MFP_CFG_DEFAULT - default MFP configuration value, with
+ * alternate function = 0,
+ * drive strength = fast 3mA (MFP_DS03X)
+ * low power mode = default
+ * edge detection = none
+ *
+ * MFP_CFG - default MFPR value with alternate function
+ * MFP_CFG_DRV - default MFPR value with alternate function and
+ * pin drive strength
+ * MFP_CFG_LPM - default MFPR value with alternate function and
+ * low power mode
+ * MFP_CFG_X - default MFPR value with alternate function,
+ * pin drive strength and low power mode
+ */
+
+typedef unsigned long mfp_cfg_t;
+
+#define MFP_PIN(x) ((x) & 0x3ff)
+
+#define MFP_AF0 (0x0 << 10)
+#define MFP_AF1 (0x1 << 10)
+#define MFP_AF2 (0x2 << 10)
+#define MFP_AF3 (0x3 << 10)
+#define MFP_AF4 (0x4 << 10)
+#define MFP_AF5 (0x5 << 10)
+#define MFP_AF6 (0x6 << 10)
+#define MFP_AF7 (0x7 << 10)
+#define MFP_AF_MASK (0x7 << 10)
+#define MFP_AF(x) (((x) >> 10) & 0x7)
+
+#define MFP_DS01X (0x0 << 13)
+#define MFP_DS02X (0x1 << 13)
+#define MFP_DS03X (0x2 << 13)
+#define MFP_DS04X (0x3 << 13)
+#define MFP_DS06X (0x4 << 13)
+#define MFP_DS08X (0x5 << 13)
+#define MFP_DS10X (0x6 << 13)
+#define MFP_DS13X (0x7 << 13)
+#define MFP_DS_MASK (0x7 << 13)
+#define MFP_DS(x) (((x) >> 13) & 0x7)
+
+#define MFP_LPM_DEFAULT (0x0 << 16)
+#define MFP_LPM_DRIVE_LOW (0x1 << 16)
+#define MFP_LPM_DRIVE_HIGH (0x2 << 16)
+#define MFP_LPM_PULL_LOW (0x3 << 16)
+#define MFP_LPM_PULL_HIGH (0x4 << 16)
+#define MFP_LPM_FLOAT (0x5 << 16)
+#define MFP_LPM_INPUT (0x6 << 16)
+#define MFP_LPM_STATE_MASK (0x7 << 16)
+#define MFP_LPM_STATE(x) (((x) >> 16) & 0x7)
+
+#define MFP_LPM_EDGE_NONE (0x0 << 19)
+#define MFP_LPM_EDGE_RISE (0x1 << 19)
+#define MFP_LPM_EDGE_FALL (0x2 << 19)
+#define MFP_LPM_EDGE_BOTH (0x3 << 19)
+#define MFP_LPM_EDGE_MASK (0x3 << 19)
+#define MFP_LPM_EDGE(x) (((x) >> 19) & 0x3)
+
+#define MFP_PULL_NONE (0x0 << 21)
+#define MFP_PULL_LOW (0x1 << 21)
+#define MFP_PULL_HIGH (0x2 << 21)
+#define MFP_PULL_BOTH (0x3 << 21)
+#define MFP_PULL_FLOAT (0x4 << 21)
+#define MFP_PULL_MASK (0x7 << 21)
+#define MFP_PULL(x) (((x) >> 21) & 0x7)
+
+#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_DEFAULT |\
+ MFP_LPM_EDGE_NONE | MFP_PULL_NONE)
+
+#define MFP_CFG(pin, af) \
+ ((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af))
+
+#define MFP_CFG_DRV(pin, af, drv) \
+ ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv))
+
+#define MFP_CFG_LPM(pin, af, lpm) \
+ ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm))
+
+#define MFP_CFG_X(pin, af, drv, lpm) \
+ ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm))
+
+#if defined(CONFIG_PXA3xx) || defined(CONFIG_ARCH_MMP)
+/*
+ * each MFP pin will have a MFPR register, since the offset of the
+ * register varies between processors, the processor specific code
+ * should initialize the pin offsets by mfp_init()
+ *
+ * mfp_init_base() - accepts a virtual base for all MFPR registers and
+ * initialize the MFP table to a default state
+ *
+ * mfp_init_addr() - accepts a table of "mfp_addr_map" structure, which
+ * represents a range of MFP pins from "start" to "end", with the offset
+ * beginning at "offset", to define a single pin, let "end" = -1.
+ *
+ * use
+ *
+ * MFP_ADDR_X() to define a range of pins
+ * MFP_ADDR() to define a single pin
+ * MFP_ADDR_END to signal the end of pin offset definitions
+ */
+struct mfp_addr_map {
+ unsigned int start;
+ unsigned int end;
+ unsigned long offset;
+};
+
+#define MFP_ADDR_X(start, end, offset) \
+ { MFP_PIN_##start, MFP_PIN_##end, offset }
+
+#define MFP_ADDR(pin, offset) \
+ { MFP_PIN_##pin, -1, offset }
+
+#define MFP_ADDR_END { MFP_PIN_INVALID, 0 }
+
+void __init mfp_init_base(void __iomem *mfpr_base);
+void __init mfp_init_addr(struct mfp_addr_map *map);
+
+/*
+ * mfp_{read, write}() - for direct read/write access to the MFPR register
+ * mfp_config() - for configuring a group of MFPR registers
+ * mfp_config_lpm() - configuring all low power MFPR registers for suspend
+ * mfp_config_run() - configuring all run time MFPR registers after resume
+ */
+unsigned long mfp_read(int mfp);
+void mfp_write(int mfp, unsigned long mfpr_val);
+void mfp_config(unsigned long *mfp_cfgs, int num);
+void mfp_config_run(void);
+void mfp_config_lpm(void);
+#endif /* CONFIG_PXA3xx || CONFIG_ARCH_MMP */
+
+#endif /* __ASM_PLAT_MFP_H */
diff --git a/src/kernel/linux/v4.14/arch/arm/plat-pxa/mfp.c b/src/kernel/linux/v4.14/arch/arm/plat-pxa/mfp.c
new file mode 100644
index 0000000..2c4dbb1
--- /dev/null
+++ b/src/kernel/linux/v4.14/arch/arm/plat-pxa/mfp.c
@@ -0,0 +1,285 @@
+/*
+ * linux/arch/arm/plat-pxa/mfp.c
+ *
+ * Multi-Function Pin Support
+ *
+ * Copyright (C) 2007 Marvell Internation Ltd.
+ *
+ * 2007-08-21: eric miao <eric.miao@marvell.com>
+ * initial version
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+
+#include <plat/mfp.h>
+
+#define MFPR_SIZE (PAGE_SIZE)
+
+/* MFPR register bit definitions */
+#define MFPR_PULL_SEL (0x1 << 15)
+#define MFPR_PULLUP_EN (0x1 << 14)
+#define MFPR_PULLDOWN_EN (0x1 << 13)
+#define MFPR_SLEEP_SEL (0x1 << 9)
+#define MFPR_SLEEP_OE_N (0x1 << 7)
+#define MFPR_EDGE_CLEAR (0x1 << 6)
+#define MFPR_EDGE_FALL_EN (0x1 << 5)
+#define MFPR_EDGE_RISE_EN (0x1 << 4)
+
+#define MFPR_SLEEP_DATA(x) ((x) << 8)
+#define MFPR_DRIVE(x) (((x) & 0x7) << 10)
+#define MFPR_AF_SEL(x) (((x) & 0x7) << 0)
+
+#define MFPR_EDGE_NONE (0)
+#define MFPR_EDGE_RISE (MFPR_EDGE_RISE_EN)
+#define MFPR_EDGE_FALL (MFPR_EDGE_FALL_EN)
+#define MFPR_EDGE_BOTH (MFPR_EDGE_RISE | MFPR_EDGE_FALL)
+
+/*
+ * Table that determines the low power modes outputs, with actual settings
+ * used in parentheses for don't-care values. Except for the float output,
+ * the configured driven and pulled levels match, so if there is a need for
+ * non-LPM pulled output, the same configuration could probably be used.
+ *
+ * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel
+ * (bit 7) (bit 8) (bit 14) (bit 13) (bit 15)
+ *
+ * Input 0 X(0) X(0) X(0) 0
+ * Drive 0 0 0 0 X(1) 0
+ * Drive 1 0 1 X(1) 0 0
+ * Pull hi (1) 1 X(1) 1 0 0
+ * Pull lo (0) 1 X(0) 0 1 0
+ * Z (float) 1 X(0) 0 0 0
+ */
+#define MFPR_LPM_INPUT (0)
+#define MFPR_LPM_DRIVE_LOW (MFPR_SLEEP_DATA(0) | MFPR_PULLDOWN_EN)
+#define MFPR_LPM_DRIVE_HIGH (MFPR_SLEEP_DATA(1) | MFPR_PULLUP_EN)
+#define MFPR_LPM_PULL_LOW (MFPR_LPM_DRIVE_LOW | MFPR_SLEEP_OE_N)
+#define MFPR_LPM_PULL_HIGH (MFPR_LPM_DRIVE_HIGH | MFPR_SLEEP_OE_N)
+#define MFPR_LPM_FLOAT (MFPR_SLEEP_OE_N)
+#define MFPR_LPM_MASK (0xe080)
+
+/*
+ * The pullup and pulldown state of the MFP pin at run mode is by default
+ * determined by the selected alternate function. In case that some buggy
+ * devices need to override this default behavior, the definitions below
+ * indicates the setting of corresponding MFPR bits
+ *
+ * Definition pull_sel pullup_en pulldown_en
+ * MFPR_PULL_NONE 0 0 0
+ * MFPR_PULL_LOW 1 0 1
+ * MFPR_PULL_HIGH 1 1 0
+ * MFPR_PULL_BOTH 1 1 1
+ * MFPR_PULL_FLOAT 1 0 0
+ */
+#define MFPR_PULL_NONE (0)
+#define MFPR_PULL_LOW (MFPR_PULL_SEL | MFPR_PULLDOWN_EN)
+#define MFPR_PULL_BOTH (MFPR_PULL_LOW | MFPR_PULLUP_EN)
+#define MFPR_PULL_HIGH (MFPR_PULL_SEL | MFPR_PULLUP_EN)
+#define MFPR_PULL_FLOAT (MFPR_PULL_SEL)
+
+/* mfp_spin_lock is used to ensure that MFP register configuration
+ * (most likely a read-modify-write operation) is atomic, and that
+ * mfp_table[] is consistent
+ */
+static DEFINE_SPINLOCK(mfp_spin_lock);
+
+static void __iomem *mfpr_mmio_base;
+
+struct mfp_pin {
+ unsigned long config; /* -1 for not configured */
+ unsigned long mfpr_off; /* MFPRxx Register offset */
+ unsigned long mfpr_run; /* Run-Mode Register Value */
+ unsigned long mfpr_lpm; /* Low Power Mode Register Value */
+};
+
+static struct mfp_pin mfp_table[MFP_PIN_MAX];
+
+/* mapping of MFP_LPM_* definitions to MFPR_LPM_* register bits */
+static const unsigned long mfpr_lpm[] = {
+ MFPR_LPM_INPUT,
+ MFPR_LPM_DRIVE_LOW,
+ MFPR_LPM_DRIVE_HIGH,
+ MFPR_LPM_PULL_LOW,
+ MFPR_LPM_PULL_HIGH,
+ MFPR_LPM_FLOAT,
+ MFPR_LPM_INPUT,
+};
+
+/* mapping of MFP_PULL_* definitions to MFPR_PULL_* register bits */
+static const unsigned long mfpr_pull[] = {
+ MFPR_PULL_NONE,
+ MFPR_PULL_LOW,
+ MFPR_PULL_HIGH,
+ MFPR_PULL_BOTH,
+ MFPR_PULL_FLOAT,
+};
+
+/* mapping of MFP_LPM_EDGE_* definitions to MFPR_EDGE_* register bits */
+static const unsigned long mfpr_edge[] = {
+ MFPR_EDGE_NONE,
+ MFPR_EDGE_RISE,
+ MFPR_EDGE_FALL,
+ MFPR_EDGE_BOTH,
+};
+
+#define mfpr_readl(off) \
+ __raw_readl(mfpr_mmio_base + (off))
+
+#define mfpr_writel(off, val) \
+ __raw_writel(val, mfpr_mmio_base + (off))
+
+#define mfp_configured(p) ((p)->config != -1)
+
+/*
+ * perform a read-back of any valid MFPR register to make sure the
+ * previous writings are finished
+ */
+static unsigned long mfpr_off_readback;
+#define mfpr_sync() (void)__raw_readl(mfpr_mmio_base + mfpr_off_readback)
+
+static inline void __mfp_config_run(struct mfp_pin *p)
+{
+ if (mfp_configured(p))
+ mfpr_writel(p->mfpr_off, p->mfpr_run);
+}
+
+static inline void __mfp_config_lpm(struct mfp_pin *p)
+{
+ if (mfp_configured(p)) {
+ unsigned long mfpr_clr = (p->mfpr_run & ~MFPR_EDGE_BOTH) | MFPR_EDGE_CLEAR;
+ if (mfpr_clr != p->mfpr_run)
+ mfpr_writel(p->mfpr_off, mfpr_clr);
+ if (p->mfpr_lpm != mfpr_clr)
+ mfpr_writel(p->mfpr_off, p->mfpr_lpm);
+ }
+}
+
+void mfp_config(unsigned long *mfp_cfgs, int num)
+{
+ unsigned long flags;
+ int i;
+
+ spin_lock_irqsave(&mfp_spin_lock, flags);
+
+ for (i = 0; i < num; i++, mfp_cfgs++) {
+ unsigned long tmp, c = *mfp_cfgs;
+ struct mfp_pin *p;
+ int pin, af, drv, lpm, edge, pull;
+
+ pin = MFP_PIN(c);
+ BUG_ON(pin >= MFP_PIN_MAX);
+ p = &mfp_table[pin];
+
+ af = MFP_AF(c);
+ drv = MFP_DS(c);
+ lpm = MFP_LPM_STATE(c);
+ edge = MFP_LPM_EDGE(c);
+ pull = MFP_PULL(c);
+
+ /* run-mode pull settings will conflict with MFPR bits of
+ * low power mode state, calculate mfpr_run and mfpr_lpm
+ * individually if pull != MFP_PULL_NONE
+ */
+ tmp = MFPR_AF_SEL(af) | MFPR_DRIVE(drv);
+
+ if (likely(pull == MFP_PULL_NONE)) {
+ p->mfpr_run = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
+ p->mfpr_lpm = p->mfpr_run;
+ } else {
+ p->mfpr_lpm = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
+ p->mfpr_run = tmp | mfpr_pull[pull];
+ }
+
+ p->config = c; __mfp_config_run(p);
+ }
+
+ mfpr_sync();
+ spin_unlock_irqrestore(&mfp_spin_lock, flags);
+}
+
+unsigned long mfp_read(int mfp)
+{
+ unsigned long val, flags;
+
+ BUG_ON(mfp < 0 || mfp >= MFP_PIN_MAX);
+
+ spin_lock_irqsave(&mfp_spin_lock, flags);
+ val = mfpr_readl(mfp_table[mfp].mfpr_off);
+ spin_unlock_irqrestore(&mfp_spin_lock, flags);
+
+ return val;
+}
+
+void mfp_write(int mfp, unsigned long val)
+{
+ unsigned long flags;
+
+ BUG_ON(mfp < 0 || mfp >= MFP_PIN_MAX);
+
+ spin_lock_irqsave(&mfp_spin_lock, flags);
+ mfpr_writel(mfp_table[mfp].mfpr_off, val);
+ mfpr_sync();
+ spin_unlock_irqrestore(&mfp_spin_lock, flags);
+}
+
+void __init mfp_init_base(void __iomem *mfpr_base)
+{
+ int i;
+
+ /* initialize the table with default - unconfigured */
+ for (i = 0; i < ARRAY_SIZE(mfp_table); i++)
+ mfp_table[i].config = -1;
+
+ mfpr_mmio_base = mfpr_base;
+}
+
+void __init mfp_init_addr(struct mfp_addr_map *map)
+{
+ struct mfp_addr_map *p;
+ unsigned long offset, flags;
+ int i;
+
+ spin_lock_irqsave(&mfp_spin_lock, flags);
+
+ /* mfp offset for readback */
+ mfpr_off_readback = map[0].offset;
+
+ for (p = map; p->start != MFP_PIN_INVALID; p++) {
+ offset = p->offset;
+ i = p->start;
+
+ do {
+ mfp_table[i].mfpr_off = offset;
+ mfp_table[i].mfpr_run = 0;
+ mfp_table[i].mfpr_lpm = 0;
+ offset += 4; i++;
+ } while ((i <= p->end) && (p->end != -1));
+ }
+
+ spin_unlock_irqrestore(&mfp_spin_lock, flags);
+}
+
+void mfp_config_lpm(void)
+{
+ struct mfp_pin *p = &mfp_table[0];
+ int pin;
+
+ for (pin = 0; pin < ARRAY_SIZE(mfp_table); pin++, p++)
+ __mfp_config_lpm(p);
+}
+
+void mfp_config_run(void)
+{
+ struct mfp_pin *p = &mfp_table[0];
+ int pin;
+
+ for (pin = 0; pin < ARRAY_SIZE(mfp_table); pin++, p++)
+ __mfp_config_run(p);
+}
diff --git a/src/kernel/linux/v4.14/arch/arm/plat-pxa/ssp.c b/src/kernel/linux/v4.14/arch/arm/plat-pxa/ssp.c
new file mode 100644
index 0000000..97bd43c
--- /dev/null
+++ b/src/kernel/linux/v4.14/arch/arm/plat-pxa/ssp.c
@@ -0,0 +1,281 @@
+/*
+ * linux/arch/arm/mach-pxa/ssp.c
+ *
+ * based on linux/arch/arm/mach-sa1100/ssp.c by Russell King
+ *
+ * Copyright (C) 2003 Russell King.
+ * Copyright (C) 2003 Wolfson Microelectronics PLC
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * PXA2xx SSP driver. This provides the generic core for simple
+ * IO-based SSP applications and allows easy port setup for DMA access.
+ *
+ * Author: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/mutex.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/spi/pxa2xx_spi.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+
+#include <asm/irq.h>
+
+static DEFINE_MUTEX(ssp_lock);
+static LIST_HEAD(ssp_list);
+
+struct ssp_device *pxa_ssp_request(int port, const char *label)
+{
+ struct ssp_device *ssp = NULL;
+
+ mutex_lock(&ssp_lock);
+
+ list_for_each_entry(ssp, &ssp_list, node) {
+ if (ssp->port_id == port && ssp->use_count == 0) {
+ ssp->use_count++;
+ ssp->label = label;
+ break;
+ }
+ }
+
+ mutex_unlock(&ssp_lock);
+
+ if (&ssp->node == &ssp_list)
+ return NULL;
+
+ return ssp;
+}
+EXPORT_SYMBOL(pxa_ssp_request);
+
+struct ssp_device *pxa_ssp_request_of(const struct device_node *of_node,
+ const char *label)
+{
+ struct ssp_device *ssp = NULL;
+
+ mutex_lock(&ssp_lock);
+
+ list_for_each_entry(ssp, &ssp_list, node) {
+ if (ssp->of_node == of_node && ssp->use_count == 0) {
+ ssp->use_count++;
+ ssp->label = label;
+ break;
+ }
+ }
+
+ mutex_unlock(&ssp_lock);
+
+ if (&ssp->node == &ssp_list)
+ return NULL;
+
+ return ssp;
+}
+EXPORT_SYMBOL(pxa_ssp_request_of);
+
+void pxa_ssp_free(struct ssp_device *ssp)
+{
+ mutex_lock(&ssp_lock);
+ if (ssp->use_count) {
+ ssp->use_count--;
+ ssp->label = NULL;
+ } else
+ dev_err(&ssp->pdev->dev, "device already free\n");
+ mutex_unlock(&ssp_lock);
+}
+EXPORT_SYMBOL(pxa_ssp_free);
+
+#ifdef CONFIG_OF
+static const struct of_device_id pxa_ssp_of_ids[] = {
+ { .compatible = "mrvl,pxa25x-ssp", .data = (void *) PXA25x_SSP },
+ { .compatible = "mvrl,pxa25x-nssp", .data = (void *) PXA25x_NSSP },
+ { .compatible = "mrvl,pxa27x-ssp", .data = (void *) PXA27x_SSP },
+ { .compatible = "mrvl,pxa3xx-ssp", .data = (void *) PXA3xx_SSP },
+ { .compatible = "mvrl,pxa168-ssp", .data = (void *) PXA168_SSP },
+ { .compatible = "mrvl,pxa910-ssp", .data = (void *) PXA910_SSP },
+ { .compatible = "mrvl,ce4100-ssp", .data = (void *) CE4100_SSP },
+ { },
+};
+MODULE_DEVICE_TABLE(of, pxa_ssp_of_ids);
+#endif
+
+static int pxa_ssp_probe(struct platform_device *pdev)
+{
+ struct resource *res;
+ struct ssp_device *ssp;
+ struct device *dev = &pdev->dev;
+
+ ssp = devm_kzalloc(dev, sizeof(struct ssp_device), GFP_KERNEL);
+ if (ssp == NULL)
+ return -ENOMEM;
+
+ ssp->pdev = pdev;
+
+ ssp->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(ssp->clk))
+ return PTR_ERR(ssp->clk);
+
+ if (dev->of_node) {
+ struct of_phandle_args dma_spec;
+ struct device_node *np = dev->of_node;
+ int ret;
+
+ /*
+ * FIXME: we should allocate the DMA channel from this
+ * context and pass the channel down to the ssp users.
+ * For now, we lookup the rx and tx indices manually
+ */
+
+ /* rx */
+ ret = of_parse_phandle_with_args(np, "dmas", "#dma-cells",
+ 0, &dma_spec);
+
+ if (ret) {
+ dev_err(dev, "Can't parse dmas property\n");
+ return -ENODEV;
+ }
+ ssp->drcmr_rx = dma_spec.args[0];
+ of_node_put(dma_spec.np);
+
+ /* tx */
+ ret = of_parse_phandle_with_args(np, "dmas", "#dma-cells",
+ 1, &dma_spec);
+ if (ret) {
+ dev_err(dev, "Can't parse dmas property\n");
+ return -ENODEV;
+ }
+ ssp->drcmr_tx = dma_spec.args[0];
+ of_node_put(dma_spec.np);
+ } else {
+ res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+ if (res == NULL) {
+ dev_err(dev, "no SSP RX DRCMR defined\n");
+ return -ENODEV;
+ }
+ ssp->drcmr_rx = res->start;
+
+ res = platform_get_resource(pdev, IORESOURCE_DMA, 1);
+ if (res == NULL) {
+ dev_err(dev, "no SSP TX DRCMR defined\n");
+ return -ENODEV;
+ }
+ ssp->drcmr_tx = res->start;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res == NULL) {
+ dev_err(dev, "no memory resource defined\n");
+ return -ENODEV;
+ }
+
+ res = devm_request_mem_region(dev, res->start, resource_size(res),
+ pdev->name);
+ if (res == NULL) {
+ dev_err(dev, "failed to request memory resource\n");
+ return -EBUSY;
+ }
+
+ ssp->phys_base = res->start;
+
+ ssp->mmio_base = devm_ioremap(dev, res->start, resource_size(res));
+ if (ssp->mmio_base == NULL) {
+ dev_err(dev, "failed to ioremap() registers\n");
+ return -ENODEV;
+ }
+
+ ssp->irq = platform_get_irq(pdev, 0);
+ if (ssp->irq < 0) {
+ dev_err(dev, "no IRQ resource defined\n");
+ return -ENODEV;
+ }
+
+ if (dev->of_node) {
+ const struct of_device_id *id =
+ of_match_device(of_match_ptr(pxa_ssp_of_ids), dev);
+ ssp->type = (int) id->data;
+ } else {
+ const struct platform_device_id *id =
+ platform_get_device_id(pdev);
+ ssp->type = (int) id->driver_data;
+
+ /* PXA2xx/3xx SSP ports starts from 1 and the internal pdev->id
+ * starts from 0, do a translation here
+ */
+ ssp->port_id = pdev->id + 1;
+ }
+
+ ssp->use_count = 0;
+ ssp->of_node = dev->of_node;
+
+ mutex_lock(&ssp_lock);
+ list_add(&ssp->node, &ssp_list);
+ mutex_unlock(&ssp_lock);
+
+ platform_set_drvdata(pdev, ssp);
+
+ return 0;
+}
+
+static int pxa_ssp_remove(struct platform_device *pdev)
+{
+ struct ssp_device *ssp;
+
+ ssp = platform_get_drvdata(pdev);
+ if (ssp == NULL)
+ return -ENODEV;
+
+ mutex_lock(&ssp_lock);
+ list_del(&ssp->node);
+ mutex_unlock(&ssp_lock);
+
+ return 0;
+}
+
+static const struct platform_device_id ssp_id_table[] = {
+ { "pxa25x-ssp", PXA25x_SSP },
+ { "pxa25x-nssp", PXA25x_NSSP },
+ { "pxa27x-ssp", PXA27x_SSP },
+ { "pxa3xx-ssp", PXA3xx_SSP },
+ { "pxa168-ssp", PXA168_SSP },
+ { "pxa910-ssp", PXA910_SSP },
+ { },
+};
+
+static struct platform_driver pxa_ssp_driver = {
+ .probe = pxa_ssp_probe,
+ .remove = pxa_ssp_remove,
+ .driver = {
+ .name = "pxa2xx-ssp",
+ .of_match_table = of_match_ptr(pxa_ssp_of_ids),
+ },
+ .id_table = ssp_id_table,
+};
+
+static int __init pxa_ssp_init(void)
+{
+ return platform_driver_register(&pxa_ssp_driver);
+}
+
+static void __exit pxa_ssp_exit(void)
+{
+ platform_driver_unregister(&pxa_ssp_driver);
+}
+
+arch_initcall(pxa_ssp_init);
+module_exit(pxa_ssp_exit);
+
+MODULE_DESCRIPTION("PXA SSP driver");
+MODULE_AUTHOR("Liam Girdwood");
+MODULE_LICENSE("GPL");