[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/arch/m68k/coldfire/sltimers.c b/src/kernel/linux/v4.14/arch/m68k/coldfire/sltimers.c
new file mode 100644
index 0000000..1b11e7b
--- /dev/null
+++ b/src/kernel/linux/v4.14/arch/m68k/coldfire/sltimers.c
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: GPL-2.0
+/***************************************************************************/
+
+/*
+ * sltimers.c -- generic ColdFire slice timer support.
+ *
+ * Copyright (C) 2009-2010, Philippe De Muyter <phdm@macqel.be>
+ * based on
+ * timers.c -- generic ColdFire hardware timer support.
+ * Copyright (C) 1999-2008, Greg Ungerer <gerg@snapgear.com>
+ */
+
+/***************************************************************************/
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/profile.h>
+#include <linux/clocksource.h>
+#include <asm/io.h>
+#include <asm/traps.h>
+#include <asm/machdep.h>
+#include <asm/coldfire.h>
+#include <asm/mcfslt.h>
+#include <asm/mcfsim.h>
+
+/***************************************************************************/
+
+#ifdef CONFIG_HIGHPROFILE
+
+/*
+ * By default use Slice Timer 1 as the profiler clock timer.
+ */
+#define PA(a) (MCFSLT_TIMER1 + (a))
+
+/*
+ * Choose a reasonably fast profile timer. Make it an odd value to
+ * try and get good coverage of kernel operations.
+ */
+#define PROFILEHZ 1013
+
+irqreturn_t mcfslt_profile_tick(int irq, void *dummy)
+{
+ /* Reset Slice Timer 1 */
+ __raw_writel(MCFSLT_SSR_BE | MCFSLT_SSR_TE, PA(MCFSLT_SSR));
+ if (current->pid)
+ profile_tick(CPU_PROFILING);
+ return IRQ_HANDLED;
+}
+
+static struct irqaction mcfslt_profile_irq = {
+ .name = "profile timer",
+ .flags = IRQF_TIMER,
+ .handler = mcfslt_profile_tick,
+};
+
+void mcfslt_profile_init(void)
+{
+ printk(KERN_INFO "PROFILE: lodging TIMER 1 @ %dHz as profile timer\n",
+ PROFILEHZ);
+
+ setup_irq(MCF_IRQ_PROFILER, &mcfslt_profile_irq);
+
+ /* Set up TIMER 2 as high speed profile clock */
+ __raw_writel(MCF_BUSCLK / PROFILEHZ - 1, PA(MCFSLT_STCNT));
+ __raw_writel(MCFSLT_SCR_RUN | MCFSLT_SCR_IEN | MCFSLT_SCR_TEN,
+ PA(MCFSLT_SCR));
+
+}
+
+#endif /* CONFIG_HIGHPROFILE */
+
+/***************************************************************************/
+
+/*
+ * By default use Slice Timer 0 as the system clock timer.
+ */
+#define TA(a) (MCFSLT_TIMER0 + (a))
+
+static u32 mcfslt_cycles_per_jiffy;
+static u32 mcfslt_cnt;
+
+static irq_handler_t timer_interrupt;
+
+static irqreturn_t mcfslt_tick(int irq, void *dummy)
+{
+ /* Reset Slice Timer 0 */
+ __raw_writel(MCFSLT_SSR_BE | MCFSLT_SSR_TE, TA(MCFSLT_SSR));
+ mcfslt_cnt += mcfslt_cycles_per_jiffy;
+ return timer_interrupt(irq, dummy);
+}
+
+static struct irqaction mcfslt_timer_irq = {
+ .name = "timer",
+ .flags = IRQF_TIMER,
+ .handler = mcfslt_tick,
+};
+
+static u64 mcfslt_read_clk(struct clocksource *cs)
+{
+ unsigned long flags;
+ u32 cycles, scnt;
+
+ local_irq_save(flags);
+ scnt = __raw_readl(TA(MCFSLT_SCNT));
+ cycles = mcfslt_cnt;
+ if (__raw_readl(TA(MCFSLT_SSR)) & MCFSLT_SSR_TE) {
+ cycles += mcfslt_cycles_per_jiffy;
+ scnt = __raw_readl(TA(MCFSLT_SCNT));
+ }
+ local_irq_restore(flags);
+
+ /* subtract because slice timers count down */
+ return cycles + ((mcfslt_cycles_per_jiffy - 1) - scnt);
+}
+
+static struct clocksource mcfslt_clk = {
+ .name = "slt",
+ .rating = 250,
+ .read = mcfslt_read_clk,
+ .mask = CLOCKSOURCE_MASK(32),
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+void hw_timer_init(irq_handler_t handler)
+{
+ mcfslt_cycles_per_jiffy = MCF_BUSCLK / HZ;
+ /*
+ * The coldfire slice timer (SLT) runs from STCNT to 0 included,
+ * then STCNT again and so on. It counts thus actually
+ * STCNT + 1 steps for 1 tick, not STCNT. So if you want
+ * n cycles, initialize STCNT with n - 1.
+ */
+ __raw_writel(mcfslt_cycles_per_jiffy - 1, TA(MCFSLT_STCNT));
+ __raw_writel(MCFSLT_SCR_RUN | MCFSLT_SCR_IEN | MCFSLT_SCR_TEN,
+ TA(MCFSLT_SCR));
+ /* initialize mcfslt_cnt knowing that slice timers count down */
+ mcfslt_cnt = mcfslt_cycles_per_jiffy;
+
+ timer_interrupt = handler;
+ setup_irq(MCF_IRQ_TIMER, &mcfslt_timer_irq);
+
+ clocksource_register_hz(&mcfslt_clk, MCF_BUSCLK);
+
+#ifdef CONFIG_HIGHPROFILE
+ mcfslt_profile_init();
+#endif
+}