[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/arch/mn10300/unit-asb2364/unit-init.c b/src/kernel/linux/v4.14/arch/mn10300/unit-asb2364/unit-init.c
new file mode 100644
index 0000000..6359b41
--- /dev/null
+++ b/src/kernel/linux/v4.14/arch/mn10300/unit-asb2364/unit-init.c
@@ -0,0 +1,132 @@
+/* ASB2364 initialisation
+ *
+ * Copyright (C) 2002 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/param.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+
+#include <asm/io.h>
+#include <asm/setup.h>
+#include <asm/processor.h>
+#include <asm/irq.h>
+#include <asm/intctl-regs.h>
+#include <asm/serial-regs.h>
+#include <unit/fpga-regs.h>
+#include <unit/serial.h>
+#include <unit/smsc911x.h>
+
+#define TTYS0_SERIAL_IER __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_IER * 2, u8)
+#define LAN_IRQ_CFG __SYSREG(SMSC911X_BASE + 0x54, u32)
+#define LAN_INT_EN __SYSREG(SMSC911X_BASE + 0x5c, u32)
+
+/*
+ * initialise some of the unit hardware before gdbstub is set up
+ */
+asmlinkage void __init unit_init(void)
+{
+ /* Make sure we aren't going to get unexpected interrupts */
+ TTYS0_SERIAL_IER = 0;
+ SC0RXICR = 0;
+ SC0TXICR = 0;
+ SC1RXICR = 0;
+ SC1TXICR = 0;
+ SC2RXICR = 0;
+ SC2TXICR = 0;
+
+ /* Attempt to reset the FPGA attached peripherals */
+ ASB2364_FPGA_REG_RESET_LAN = 0x0000;
+ SyncExBus();
+ ASB2364_FPGA_REG_RESET_UART = 0x0000;
+ SyncExBus();
+ ASB2364_FPGA_REG_RESET_I2C = 0x0000;
+ SyncExBus();
+ ASB2364_FPGA_REG_RESET_USB = 0x0000;
+ SyncExBus();
+ ASB2364_FPGA_REG_RESET_AV = 0x0000;
+ SyncExBus();
+
+ /* set up the external interrupts */
+
+ /* XIRQ[0]: NAND RXBY */
+ /* SET_XIRQ_TRIGGER(0, XIRQ_TRIGGER_LOWLEVEL); */
+
+ /* XIRQ[1]: LAN, UART, I2C, USB, PCI, FPGA */
+ SET_XIRQ_TRIGGER(1, XIRQ_TRIGGER_LOWLEVEL);
+
+ /* XIRQ[2]: Extend Slot 1-9 */
+ /* SET_XIRQ_TRIGGER(2, XIRQ_TRIGGER_LOWLEVEL); */
+
+#if defined(CONFIG_EXT_SERIAL_IRQ_LEVEL) && \
+ defined(CONFIG_ETHERNET_IRQ_LEVEL) && \
+ (CONFIG_EXT_SERIAL_IRQ_LEVEL != CONFIG_ETHERNET_IRQ_LEVEL)
+# error CONFIG_EXT_SERIAL_IRQ_LEVEL != CONFIG_ETHERNET_IRQ_LEVEL
+#endif
+
+#if defined(CONFIG_EXT_SERIAL_IRQ_LEVEL)
+ set_intr_level(XIRQ1, NUM2GxICR_LEVEL(CONFIG_EXT_SERIAL_IRQ_LEVEL));
+#elif defined(CONFIG_ETHERNET_IRQ_LEVEL)
+ set_intr_level(XIRQ1, NUM2GxICR_LEVEL(CONFIG_ETHERNET_IRQ_LEVEL));
+#endif
+}
+
+/*
+ * initialise the rest of the unit hardware after gdbstub is ready
+ */
+asmlinkage void __init unit_setup(void)
+{
+ /* Release the reset on the SMSC911X so that it is ready by the time we
+ * need it */
+ ASB2364_FPGA_REG_RESET_LAN = 0x0001;
+ SyncExBus();
+ ASB2364_FPGA_REG_RESET_UART = 0x0001;
+ SyncExBus();
+ ASB2364_FPGA_REG_RESET_I2C = 0x0001;
+ SyncExBus();
+ ASB2364_FPGA_REG_RESET_USB = 0x0001;
+ SyncExBus();
+ ASB2364_FPGA_REG_RESET_AV = 0x0001;
+ SyncExBus();
+
+ /* Make sure the ethernet chipset isn't going to give us an interrupt
+ * storm from stuff it was doing pre-reset */
+ LAN_IRQ_CFG = 0;
+ LAN_INT_EN = 0;
+}
+
+/*
+ * initialise the external interrupts used by a unit of this type
+ */
+void __init unit_init_IRQ(void)
+{
+ unsigned int extnum;
+
+ for (extnum = 0 ; extnum < NR_XIRQS ; extnum++) {
+ switch (GET_XIRQ_TRIGGER(extnum)) {
+ /* LEVEL triggered interrupts should be made
+ * post-ACK'able as they hold their lines until
+ * serviced
+ */
+ case XIRQ_TRIGGER_HILEVEL:
+ case XIRQ_TRIGGER_LOWLEVEL:
+ mn10300_set_lateack_irq_type(XIRQ2IRQ(extnum));
+ break;
+ default:
+ break;
+ }
+ }
+
+#define IRQCTL __SYSREG(0xd5000090, u32)
+ IRQCTL |= 0x02;
+
+ irq_fpga_init();
+}