[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/drivers/ata/pata_hpt3x3.c b/src/kernel/linux/v4.14/drivers/ata/pata_hpt3x3.c
new file mode 100644
index 0000000..b2fc023
--- /dev/null
+++ b/src/kernel/linux/v4.14/drivers/ata/pata_hpt3x3.c
@@ -0,0 +1,292 @@
+/*
+ * pata_hpt3x3 - HPT3x3 driver
+ * (c) Copyright 2005-2006 Red Hat
+ *
+ * Was pata_hpt34x but the naming was confusing as it supported the
+ * 343 and 363 so it has been renamed.
+ *
+ * Based on:
+ * linux/drivers/ide/pci/hpt34x.c Version 0.40 Sept 10, 2002
+ * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ *
+ * May be copied or modified under the terms of the GNU General Public
+ * License
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_hpt3x3"
+#define DRV_VERSION "0.6.1"
+
+/**
+ * hpt3x3_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Set our PIO requirements. This is fairly simple on the HPT3x3 as
+ * all we have to do is clear the MWDMA and UDMA bits then load the
+ * mode number.
+ */
+
+static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 r1, r2;
+ int dn = 2 * ap->port_no + adev->devno;
+
+ pci_read_config_dword(pdev, 0x44, &r1);
+ pci_read_config_dword(pdev, 0x48, &r2);
+ /* Load the PIO timing number */
+ r1 &= ~(7 << (3 * dn));
+ r1 |= (adev->pio_mode - XFER_PIO_0) << (3 * dn);
+ r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */
+
+ pci_write_config_dword(pdev, 0x44, r1);
+ pci_write_config_dword(pdev, 0x48, r2);
+}
+
+#if defined(CONFIG_PATA_HPT3X3_DMA)
+/**
+ * hpt3x3_set_dmamode - DMA timing setup
+ * @ap: ATA interface
+ * @adev: Device being configured
+ *
+ * Set up the channel for MWDMA or UDMA modes. Much the same as with
+ * PIO, load the mode number and then set MWDMA or UDMA flag.
+ *
+ * 0x44 : bit 0-2 master mode, 3-5 slave mode, etc
+ * 0x48 : bit 4/0 DMA/UDMA bit 5/1 for slave etc
+ */
+
+static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 r1, r2;
+ int dn = 2 * ap->port_no + adev->devno;
+ int mode_num = adev->dma_mode & 0x0F;
+
+ pci_read_config_dword(pdev, 0x44, &r1);
+ pci_read_config_dword(pdev, 0x48, &r2);
+ /* Load the timing number */
+ r1 &= ~(7 << (3 * dn));
+ r1 |= (mode_num << (3 * dn));
+ r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */
+
+ if (adev->dma_mode >= XFER_UDMA_0)
+ r2 |= (0x01 << dn); /* Ultra mode */
+ else
+ r2 |= (0x10 << dn); /* MWDMA */
+
+ pci_write_config_dword(pdev, 0x44, r1);
+ pci_write_config_dword(pdev, 0x48, r2);
+}
+
+/**
+ * hpt3x3_freeze - DMA workaround
+ * @ap: port to freeze
+ *
+ * When freezing an HPT3x3 we must stop any pending DMA before
+ * writing to the control register or the chip will hang
+ */
+
+static void hpt3x3_freeze(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+ iowrite8(ioread8(mmio + ATA_DMA_CMD) & ~ ATA_DMA_START,
+ mmio + ATA_DMA_CMD);
+ ata_sff_dma_pause(ap);
+ ata_sff_freeze(ap);
+}
+
+/**
+ * hpt3x3_bmdma_setup - DMA workaround
+ * @qc: Queued command
+ *
+ * When issuing BMDMA we must clean up the error/active bits in
+ * software on this device
+ */
+
+static void hpt3x3_bmdma_setup(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ u8 r = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+ r |= ATA_DMA_INTR | ATA_DMA_ERR;
+ iowrite8(r, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+ return ata_bmdma_setup(qc);
+}
+
+/**
+ * hpt3x3_atapi_dma - ATAPI DMA check
+ * @qc: Queued command
+ *
+ * Just say no - we don't do ATAPI DMA
+ */
+
+static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc)
+{
+ return 1;
+}
+
+#endif /* CONFIG_PATA_HPT3X3_DMA */
+
+static struct scsi_host_template hpt3x3_sht = {
+ ATA_BMDMA_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations hpt3x3_port_ops = {
+ .inherits = &ata_bmdma_port_ops,
+ .cable_detect = ata_cable_40wire,
+ .set_piomode = hpt3x3_set_piomode,
+#if defined(CONFIG_PATA_HPT3X3_DMA)
+ .set_dmamode = hpt3x3_set_dmamode,
+ .bmdma_setup = hpt3x3_bmdma_setup,
+ .check_atapi_dma= hpt3x3_atapi_dma,
+ .freeze = hpt3x3_freeze,
+#endif
+
+};
+
+/**
+ * hpt3x3_init_chipset - chip setup
+ * @dev: PCI device
+ *
+ * Perform the setup required at boot and on resume.
+ */
+
+static void hpt3x3_init_chipset(struct pci_dev *dev)
+{
+ u16 cmd;
+ /* Initialize the board */
+ pci_write_config_word(dev, 0x80, 0x00);
+ /* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */
+ pci_read_config_word(dev, PCI_COMMAND, &cmd);
+ if (cmd & PCI_COMMAND_MEMORY)
+ pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0);
+ else
+ pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
+}
+
+/**
+ * hpt3x3_init_one - Initialise an HPT343/363
+ * @pdev: PCI device
+ * @id: Entry in match table
+ *
+ * Perform basic initialisation. We set the device up so we access all
+ * ports via BAR4. This is necessary to work around errata.
+ */
+
+static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+ static const struct ata_port_info info = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+#if defined(CONFIG_PATA_HPT3X3_DMA)
+ /* Further debug needed */
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
+#endif
+ .port_ops = &hpt3x3_port_ops
+ };
+ /* Register offsets of taskfiles in BAR4 area */
+ static const u8 offset_cmd[2] = { 0x20, 0x28 };
+ static const u8 offset_ctl[2] = { 0x36, 0x3E };
+ const struct ata_port_info *ppi[] = { &info, NULL };
+ struct ata_host *host;
+ int i, rc;
+ void __iomem *base;
+
+ hpt3x3_init_chipset(pdev);
+
+ ata_print_version_once(&pdev->dev, DRV_VERSION);
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
+ if (!host)
+ return -ENOMEM;
+ /* acquire resources and fill host */
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ /* Everything is relative to BAR4 if we set up this way */
+ rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME);
+ if (rc == -EBUSY)
+ pcim_pin_device(pdev);
+ if (rc)
+ return rc;
+ host->iomap = pcim_iomap_table(pdev);
+ rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+ rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+
+ base = host->iomap[4]; /* Bus mastering base */
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ ioaddr->cmd_addr = base + offset_cmd[i];
+ ioaddr->altstatus_addr =
+ ioaddr->ctl_addr = base + offset_ctl[i];
+ ioaddr->scr_addr = NULL;
+ ata_sff_std_ports(ioaddr);
+ ioaddr->bmdma_addr = base + 8 * i;
+
+ ata_port_pbar_desc(ap, 4, -1, "ioport");
+ ata_port_pbar_desc(ap, 4, offset_cmd[i], "cmd");
+ }
+ pci_set_master(pdev);
+ return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
+ IRQF_SHARED, &hpt3x3_sht);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int hpt3x3_reinit_one(struct pci_dev *dev)
+{
+ struct ata_host *host = pci_get_drvdata(dev);
+ int rc;
+
+ rc = ata_pci_device_do_resume(dev);
+ if (rc)
+ return rc;
+
+ hpt3x3_init_chipset(dev);
+
+ ata_host_resume(host);
+ return 0;
+}
+#endif
+
+static const struct pci_device_id hpt3x3[] = {
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT343), },
+
+ { },
+};
+
+static struct pci_driver hpt3x3_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = hpt3x3,
+ .probe = hpt3x3_init_one,
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM_SLEEP
+ .suspend = ata_pci_device_suspend,
+ .resume = hpt3x3_reinit_one,
+#endif
+};
+
+module_pci_driver(hpt3x3_pci_driver);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt3x3);
+MODULE_VERSION(DRV_VERSION);