[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/drivers/dma/amba-pl08x.c b/src/kernel/linux/v4.14/drivers/dma/amba-pl08x.c
new file mode 100644
index 0000000..b52b0d5
--- /dev/null
+++ b/src/kernel/linux/v4.14/drivers/dma/amba-pl08x.c
@@ -0,0 +1,3088 @@
+/*
+ * Copyright (c) 2006 ARM Ltd.
+ * Copyright (c) 2010 ST-Ericsson SA
+ * Copyirght (c) 2017 Linaro Ltd.
+ *
+ * Author: Peter Pearse <peter.pearse@arm.com>
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * The full GNU General Public License is in this distribution in the file
+ * called COPYING.
+ *
+ * Documentation: ARM DDI 0196G == PL080
+ * Documentation: ARM DDI 0218E == PL081
+ * Documentation: S3C6410 User's Manual == PL080S
+ *
+ * PL080 & PL081 both have 16 sets of DMA signals that can be routed to any
+ * channel.
+ *
+ * The PL080 has 8 channels available for simultaneous use, and the PL081
+ * has only two channels. So on these DMA controllers the number of channels
+ * and the number of incoming DMA signals are two totally different things.
+ * It is usually not possible to theoretically handle all physical signals,
+ * so a multiplexing scheme with possible denial of use is necessary.
+ *
+ * The PL080 has a dual bus master, PL081 has a single master.
+ *
+ * PL080S is a version modified by Samsung and used in S3C64xx SoCs.
+ * It differs in following aspects:
+ * - CH_CONFIG register at different offset,
+ * - separate CH_CONTROL2 register for transfer size,
+ * - bigger maximum transfer size,
+ * - 8-word aligned LLI, instead of 4-word, due to extra CCTL2 word,
+ * - no support for peripheral flow control.
+ *
+ * Memory to peripheral transfer may be visualized as
+ * Get data from memory to DMAC
+ * Until no data left
+ * On burst request from peripheral
+ * Destination burst from DMAC to peripheral
+ * Clear burst request
+ * Raise terminal count interrupt
+ *
+ * For peripherals with a FIFO:
+ * Source burst size == half the depth of the peripheral FIFO
+ * Destination burst size == the depth of the peripheral FIFO
+ *
+ * (Bursts are irrelevant for mem to mem transfers - there are no burst
+ * signals, the DMA controller will simply facilitate its AHB master.)
+ *
+ * ASSUMES default (little) endianness for DMA transfers
+ *
+ * The PL08x has two flow control settings:
+ * - DMAC flow control: the transfer size defines the number of transfers
+ * which occur for the current LLI entry, and the DMAC raises TC at the
+ * end of every LLI entry. Observed behaviour shows the DMAC listening
+ * to both the BREQ and SREQ signals (contrary to documented),
+ * transferring data if either is active. The LBREQ and LSREQ signals
+ * are ignored.
+ *
+ * - Peripheral flow control: the transfer size is ignored (and should be
+ * zero). The data is transferred from the current LLI entry, until
+ * after the final transfer signalled by LBREQ or LSREQ. The DMAC
+ * will then move to the next LLI entry. Unsupported by PL080S.
+ */
+#include <linux/amba/bus.h>
+#include <linux/amba/pl08x.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dmaengine.h>
+#include <linux/dmapool.h>
+#include <linux/dma-mapping.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_dma.h>
+#include <linux/pm_runtime.h>
+#include <linux/seq_file.h>
+#include <linux/slab.h>
+#include <linux/amba/pl080.h>
+
+#include "dmaengine.h"
+#include "virt-dma.h"
+
+#define DRIVER_NAME "pl08xdmac"
+
+#define PL80X_DMA_BUSWIDTHS \
+ BIT(DMA_SLAVE_BUSWIDTH_UNDEFINED) | \
+ BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) | \
+ BIT(DMA_SLAVE_BUSWIDTH_2_BYTES) | \
+ BIT(DMA_SLAVE_BUSWIDTH_4_BYTES)
+
+static struct amba_driver pl08x_amba_driver;
+struct pl08x_driver_data;
+
+/**
+ * struct vendor_data - vendor-specific config parameters for PL08x derivatives
+ * @config_offset: offset to the configuration register
+ * @channels: the number of channels available in this variant
+ * @signals: the number of request signals available from the hardware
+ * @dualmaster: whether this version supports dual AHB masters or not.
+ * @nomadik: whether this variant is a ST Microelectronics Nomadik, where the
+ * channels have Nomadik security extension bits that need to be checked
+ * for permission before use and some registers are missing
+ * @pl080s: whether this variant is a Samsung PL080S, which has separate
+ * register and LLI word for transfer size.
+ * @ftdmac020: whether this variant is a Faraday Technology FTDMAC020
+ * @max_transfer_size: the maximum single element transfer size for this
+ * PL08x variant.
+ */
+struct vendor_data {
+ u8 config_offset;
+ u8 channels;
+ u8 signals;
+ bool dualmaster;
+ bool nomadik;
+ bool pl080s;
+ bool ftdmac020;
+ u32 max_transfer_size;
+};
+
+/**
+ * struct pl08x_bus_data - information of source or destination
+ * busses for a transfer
+ * @addr: current address
+ * @maxwidth: the maximum width of a transfer on this bus
+ * @buswidth: the width of this bus in bytes: 1, 2 or 4
+ */
+struct pl08x_bus_data {
+ dma_addr_t addr;
+ u8 maxwidth;
+ u8 buswidth;
+};
+
+#define IS_BUS_ALIGNED(bus) IS_ALIGNED((bus)->addr, (bus)->buswidth)
+
+/**
+ * struct pl08x_phy_chan - holder for the physical channels
+ * @id: physical index to this channel
+ * @base: memory base address for this physical channel
+ * @reg_config: configuration address for this physical channel
+ * @reg_control: control address for this physical channel
+ * @reg_src: transfer source address register
+ * @reg_dst: transfer destination address register
+ * @reg_lli: transfer LLI address register
+ * @reg_busy: if the variant has a special per-channel busy register,
+ * this contains a pointer to it
+ * @lock: a lock to use when altering an instance of this struct
+ * @serving: the virtual channel currently being served by this physical
+ * channel
+ * @locked: channel unavailable for the system, e.g. dedicated to secure
+ * world
+ * @ftdmac020: channel is on a FTDMAC020
+ * @pl080s: channel is on a PL08s
+ */
+struct pl08x_phy_chan {
+ unsigned int id;
+ void __iomem *base;
+ void __iomem *reg_config;
+ void __iomem *reg_control;
+ void __iomem *reg_src;
+ void __iomem *reg_dst;
+ void __iomem *reg_lli;
+ void __iomem *reg_busy;
+ spinlock_t lock;
+ struct pl08x_dma_chan *serving;
+ bool locked;
+ bool ftdmac020;
+ bool pl080s;
+};
+
+/**
+ * struct pl08x_sg - structure containing data per sg
+ * @src_addr: src address of sg
+ * @dst_addr: dst address of sg
+ * @len: transfer len in bytes
+ * @node: node for txd's dsg_list
+ */
+struct pl08x_sg {
+ dma_addr_t src_addr;
+ dma_addr_t dst_addr;
+ size_t len;
+ struct list_head node;
+};
+
+/**
+ * struct pl08x_txd - wrapper for struct dma_async_tx_descriptor
+ * @vd: virtual DMA descriptor
+ * @dsg_list: list of children sg's
+ * @llis_bus: DMA memory address (physical) start for the LLIs
+ * @llis_va: virtual memory address start for the LLIs
+ * @cctl: control reg values for current txd
+ * @ccfg: config reg values for current txd
+ * @done: this marks completed descriptors, which should not have their
+ * mux released.
+ * @cyclic: indicate cyclic transfers
+ */
+struct pl08x_txd {
+ struct virt_dma_desc vd;
+ struct list_head dsg_list;
+ dma_addr_t llis_bus;
+ u32 *llis_va;
+ /* Default cctl value for LLIs */
+ u32 cctl;
+ /*
+ * Settings to be put into the physical channel when we
+ * trigger this txd. Other registers are in llis_va[0].
+ */
+ u32 ccfg;
+ bool done;
+ bool cyclic;
+};
+
+/**
+ * enum pl08x_dma_chan_state - holds the PL08x specific virtual channel
+ * states
+ * @PL08X_CHAN_IDLE: the channel is idle
+ * @PL08X_CHAN_RUNNING: the channel has allocated a physical transport
+ * channel and is running a transfer on it
+ * @PL08X_CHAN_PAUSED: the channel has allocated a physical transport
+ * channel, but the transfer is currently paused
+ * @PL08X_CHAN_WAITING: the channel is waiting for a physical transport
+ * channel to become available (only pertains to memcpy channels)
+ */
+enum pl08x_dma_chan_state {
+ PL08X_CHAN_IDLE,
+ PL08X_CHAN_RUNNING,
+ PL08X_CHAN_PAUSED,
+ PL08X_CHAN_WAITING,
+};
+
+/**
+ * struct pl08x_dma_chan - this structure wraps a DMA ENGINE channel
+ * @vc: wrappped virtual channel
+ * @phychan: the physical channel utilized by this channel, if there is one
+ * @name: name of channel
+ * @cd: channel platform data
+ * @cfg: slave configuration
+ * @at: active transaction on this channel
+ * @host: a pointer to the host (internal use)
+ * @state: whether the channel is idle, paused, running etc
+ * @slave: whether this channel is a device (slave) or for memcpy
+ * @signal: the physical DMA request signal which this channel is using
+ * @mux_use: count of descriptors using this DMA request signal setting
+ */
+struct pl08x_dma_chan {
+ struct virt_dma_chan vc;
+ struct pl08x_phy_chan *phychan;
+ const char *name;
+ struct pl08x_channel_data *cd;
+ struct dma_slave_config cfg;
+ struct pl08x_txd *at;
+ struct pl08x_driver_data *host;
+ enum pl08x_dma_chan_state state;
+ bool slave;
+ int signal;
+ unsigned mux_use;
+};
+
+/**
+ * struct pl08x_driver_data - the local state holder for the PL08x
+ * @slave: optional slave engine for this instance
+ * @memcpy: memcpy engine for this instance
+ * @has_slave: the PL08x has a slave engine (routed signals)
+ * @base: virtual memory base (remapped) for the PL08x
+ * @adev: the corresponding AMBA (PrimeCell) bus entry
+ * @vd: vendor data for this PL08x variant
+ * @pd: platform data passed in from the platform/machine
+ * @phy_chans: array of data for the physical channels
+ * @pool: a pool for the LLI descriptors
+ * @lli_buses: bitmask to or in to LLI pointer selecting AHB port for LLI
+ * fetches
+ * @mem_buses: set to indicate memory transfers on AHB2.
+ * @lli_words: how many words are used in each LLI item for this variant
+ */
+struct pl08x_driver_data {
+ struct dma_device slave;
+ struct dma_device memcpy;
+ bool has_slave;
+ void __iomem *base;
+ struct amba_device *adev;
+ const struct vendor_data *vd;
+ struct pl08x_platform_data *pd;
+ struct pl08x_phy_chan *phy_chans;
+ struct dma_pool *pool;
+ u8 lli_buses;
+ u8 mem_buses;
+ u8 lli_words;
+};
+
+/*
+ * PL08X specific defines
+ */
+
+/* The order of words in an LLI. */
+#define PL080_LLI_SRC 0
+#define PL080_LLI_DST 1
+#define PL080_LLI_LLI 2
+#define PL080_LLI_CCTL 3
+#define PL080S_LLI_CCTL2 4
+
+/* Total words in an LLI. */
+#define PL080_LLI_WORDS 4
+#define PL080S_LLI_WORDS 8
+
+/*
+ * Number of LLIs in each LLI buffer allocated for one transfer
+ * (maximum times we call dma_pool_alloc on this pool without freeing)
+ */
+#define MAX_NUM_TSFR_LLIS 512
+#define PL08X_ALIGN 8
+
+static inline struct pl08x_dma_chan *to_pl08x_chan(struct dma_chan *chan)
+{
+ return container_of(chan, struct pl08x_dma_chan, vc.chan);
+}
+
+static inline struct pl08x_txd *to_pl08x_txd(struct dma_async_tx_descriptor *tx)
+{
+ return container_of(tx, struct pl08x_txd, vd.tx);
+}
+
+/*
+ * Mux handling.
+ *
+ * This gives us the DMA request input to the PL08x primecell which the
+ * peripheral described by the channel data will be routed to, possibly
+ * via a board/SoC specific external MUX. One important point to note
+ * here is that this does not depend on the physical channel.
+ */
+static int pl08x_request_mux(struct pl08x_dma_chan *plchan)
+{
+ const struct pl08x_platform_data *pd = plchan->host->pd;
+ int ret;
+
+ if (plchan->mux_use++ == 0 && pd->get_xfer_signal) {
+ ret = pd->get_xfer_signal(plchan->cd);
+ if (ret < 0) {
+ plchan->mux_use = 0;
+ return ret;
+ }
+
+ plchan->signal = ret;
+ }
+ return 0;
+}
+
+static void pl08x_release_mux(struct pl08x_dma_chan *plchan)
+{
+ const struct pl08x_platform_data *pd = plchan->host->pd;
+
+ if (plchan->signal >= 0) {
+ WARN_ON(plchan->mux_use == 0);
+
+ if (--plchan->mux_use == 0 && pd->put_xfer_signal) {
+ pd->put_xfer_signal(plchan->cd, plchan->signal);
+ plchan->signal = -1;
+ }
+ }
+}
+
+/*
+ * Physical channel handling
+ */
+
+/* Whether a certain channel is busy or not */
+static int pl08x_phy_channel_busy(struct pl08x_phy_chan *ch)
+{
+ unsigned int val;
+
+ /* If we have a special busy register, take a shortcut */
+ if (ch->reg_busy) {
+ val = readl(ch->reg_busy);
+ return !!(val & BIT(ch->id));
+ }
+ val = readl(ch->reg_config);
+ return val & PL080_CONFIG_ACTIVE;
+}
+
+/*
+ * pl08x_write_lli() - Write an LLI into the DMA controller.
+ *
+ * The PL08x derivatives support linked lists, but the first item of the
+ * list containing the source, destination, control word and next LLI is
+ * ignored. Instead the driver has to write those values directly into the
+ * SRC, DST, LLI and control registers. On FTDMAC020 also the SIZE
+ * register need to be set up for the first transfer.
+ */
+static void pl08x_write_lli(struct pl08x_driver_data *pl08x,
+ struct pl08x_phy_chan *phychan, const u32 *lli, u32 ccfg)
+{
+ if (pl08x->vd->pl080s)
+ dev_vdbg(&pl08x->adev->dev,
+ "WRITE channel %d: csrc=0x%08x, cdst=0x%08x, "
+ "clli=0x%08x, cctl=0x%08x, cctl2=0x%08x, ccfg=0x%08x\n",
+ phychan->id, lli[PL080_LLI_SRC], lli[PL080_LLI_DST],
+ lli[PL080_LLI_LLI], lli[PL080_LLI_CCTL],
+ lli[PL080S_LLI_CCTL2], ccfg);
+ else
+ dev_vdbg(&pl08x->adev->dev,
+ "WRITE channel %d: csrc=0x%08x, cdst=0x%08x, "
+ "clli=0x%08x, cctl=0x%08x, ccfg=0x%08x\n",
+ phychan->id, lli[PL080_LLI_SRC], lli[PL080_LLI_DST],
+ lli[PL080_LLI_LLI], lli[PL080_LLI_CCTL], ccfg);
+
+ writel_relaxed(lli[PL080_LLI_SRC], phychan->reg_src);
+ writel_relaxed(lli[PL080_LLI_DST], phychan->reg_dst);
+ writel_relaxed(lli[PL080_LLI_LLI], phychan->reg_lli);
+
+ /*
+ * The FTMAC020 has a different layout in the CCTL word of the LLI
+ * and the CCTL register which is split in CSR and SIZE registers.
+ * Convert the LLI item CCTL into the proper values to write into
+ * the CSR and SIZE registers.
+ */
+ if (phychan->ftdmac020) {
+ u32 llictl = lli[PL080_LLI_CCTL];
+ u32 val = 0;
+
+ /* Write the transfer size (12 bits) to the size register */
+ writel_relaxed(llictl & FTDMAC020_LLI_TRANSFER_SIZE_MASK,
+ phychan->base + FTDMAC020_CH_SIZE);
+ /*
+ * Then write the control bits 28..16 to the control register
+ * by shuffleing the bits around to where they are in the
+ * main register. The mapping is as follows:
+ * Bit 28: TC_MSK - mask on all except last LLI
+ * Bit 27..25: SRC_WIDTH
+ * Bit 24..22: DST_WIDTH
+ * Bit 21..20: SRCAD_CTRL
+ * Bit 19..17: DSTAD_CTRL
+ * Bit 17: SRC_SEL
+ * Bit 16: DST_SEL
+ */
+ if (llictl & FTDMAC020_LLI_TC_MSK)
+ val |= FTDMAC020_CH_CSR_TC_MSK;
+ val |= ((llictl & FTDMAC020_LLI_SRC_WIDTH_MSK) >>
+ (FTDMAC020_LLI_SRC_WIDTH_SHIFT -
+ FTDMAC020_CH_CSR_SRC_WIDTH_SHIFT));
+ val |= ((llictl & FTDMAC020_LLI_DST_WIDTH_MSK) >>
+ (FTDMAC020_LLI_DST_WIDTH_SHIFT -
+ FTDMAC020_CH_CSR_DST_WIDTH_SHIFT));
+ val |= ((llictl & FTDMAC020_LLI_SRCAD_CTL_MSK) >>
+ (FTDMAC020_LLI_SRCAD_CTL_SHIFT -
+ FTDMAC020_CH_CSR_SRCAD_CTL_SHIFT));
+ val |= ((llictl & FTDMAC020_LLI_DSTAD_CTL_MSK) >>
+ (FTDMAC020_LLI_DSTAD_CTL_SHIFT -
+ FTDMAC020_CH_CSR_DSTAD_CTL_SHIFT));
+ if (llictl & FTDMAC020_LLI_SRC_SEL)
+ val |= FTDMAC020_CH_CSR_SRC_SEL;
+ if (llictl & FTDMAC020_LLI_DST_SEL)
+ val |= FTDMAC020_CH_CSR_DST_SEL;
+
+ /*
+ * Set up the bits that exist in the CSR but are not
+ * part the LLI, i.e. only gets written to the control
+ * register right here.
+ *
+ * FIXME: do not just handle memcpy, also handle slave DMA.
+ */
+ switch (pl08x->pd->memcpy_burst_size) {
+ default:
+ case PL08X_BURST_SZ_1:
+ val |= PL080_BSIZE_1 <<
+ FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_4:
+ val |= PL080_BSIZE_4 <<
+ FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_8:
+ val |= PL080_BSIZE_8 <<
+ FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_16:
+ val |= PL080_BSIZE_16 <<
+ FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_32:
+ val |= PL080_BSIZE_32 <<
+ FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_64:
+ val |= PL080_BSIZE_64 <<
+ FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_128:
+ val |= PL080_BSIZE_128 <<
+ FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_256:
+ val |= PL080_BSIZE_256 <<
+ FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+ break;
+ }
+
+ /* Protection flags */
+ if (pl08x->pd->memcpy_prot_buff)
+ val |= FTDMAC020_CH_CSR_PROT2;
+ if (pl08x->pd->memcpy_prot_cache)
+ val |= FTDMAC020_CH_CSR_PROT3;
+ /* We are the kernel, so we are in privileged mode */
+ val |= FTDMAC020_CH_CSR_PROT1;
+
+ writel_relaxed(val, phychan->reg_control);
+ } else {
+ /* Bits are just identical */
+ writel_relaxed(lli[PL080_LLI_CCTL], phychan->reg_control);
+ }
+
+ /* Second control word on the PL080s */
+ if (pl08x->vd->pl080s)
+ writel_relaxed(lli[PL080S_LLI_CCTL2],
+ phychan->base + PL080S_CH_CONTROL2);
+
+ writel(ccfg, phychan->reg_config);
+}
+
+/*
+ * Set the initial DMA register values i.e. those for the first LLI
+ * The next LLI pointer and the configuration interrupt bit have
+ * been set when the LLIs were constructed. Poke them into the hardware
+ * and start the transfer.
+ */
+static void pl08x_start_next_txd(struct pl08x_dma_chan *plchan)
+{
+ struct pl08x_driver_data *pl08x = plchan->host;
+ struct pl08x_phy_chan *phychan = plchan->phychan;
+ struct virt_dma_desc *vd = vchan_next_desc(&plchan->vc);
+ struct pl08x_txd *txd = to_pl08x_txd(&vd->tx);
+ u32 val;
+
+ list_del(&txd->vd.node);
+
+ plchan->at = txd;
+
+ /* Wait for channel inactive */
+ while (pl08x_phy_channel_busy(phychan))
+ cpu_relax();
+
+ pl08x_write_lli(pl08x, phychan, &txd->llis_va[0], txd->ccfg);
+
+ /* Enable the DMA channel */
+ /* Do not access config register until channel shows as disabled */
+ while (readl(pl08x->base + PL080_EN_CHAN) & BIT(phychan->id))
+ cpu_relax();
+
+ /* Do not access config register until channel shows as inactive */
+ if (phychan->ftdmac020) {
+ val = readl(phychan->reg_config);
+ while (val & FTDMAC020_CH_CFG_BUSY)
+ val = readl(phychan->reg_config);
+
+ val = readl(phychan->reg_control);
+ while (val & FTDMAC020_CH_CSR_EN)
+ val = readl(phychan->reg_control);
+
+ writel(val | FTDMAC020_CH_CSR_EN,
+ phychan->reg_control);
+ } else {
+ val = readl(phychan->reg_config);
+ while ((val & PL080_CONFIG_ACTIVE) ||
+ (val & PL080_CONFIG_ENABLE))
+ val = readl(phychan->reg_config);
+
+ writel(val | PL080_CONFIG_ENABLE, phychan->reg_config);
+ }
+}
+
+/*
+ * Pause the channel by setting the HALT bit.
+ *
+ * For M->P transfers, pause the DMAC first and then stop the peripheral -
+ * the FIFO can only drain if the peripheral is still requesting data.
+ * (note: this can still timeout if the DMAC FIFO never drains of data.)
+ *
+ * For P->M transfers, disable the peripheral first to stop it filling
+ * the DMAC FIFO, and then pause the DMAC.
+ */
+static void pl08x_pause_phy_chan(struct pl08x_phy_chan *ch)
+{
+ u32 val;
+ int timeout;
+
+ if (ch->ftdmac020) {
+ /* Use the enable bit on the FTDMAC020 */
+ val = readl(ch->reg_control);
+ val &= ~FTDMAC020_CH_CSR_EN;
+ writel(val, ch->reg_control);
+ return;
+ }
+
+ /* Set the HALT bit and wait for the FIFO to drain */
+ val = readl(ch->reg_config);
+ val |= PL080_CONFIG_HALT;
+ writel(val, ch->reg_config);
+
+ /* Wait for channel inactive */
+ for (timeout = 1000; timeout; timeout--) {
+ if (!pl08x_phy_channel_busy(ch))
+ break;
+ udelay(1);
+ }
+ if (pl08x_phy_channel_busy(ch))
+ pr_err("pl08x: channel%u timeout waiting for pause\n", ch->id);
+}
+
+static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
+{
+ u32 val;
+
+ /* Use the enable bit on the FTDMAC020 */
+ if (ch->ftdmac020) {
+ val = readl(ch->reg_control);
+ val |= FTDMAC020_CH_CSR_EN;
+ writel(val, ch->reg_control);
+ return;
+ }
+
+ /* Clear the HALT bit */
+ val = readl(ch->reg_config);
+ val &= ~PL080_CONFIG_HALT;
+ writel(val, ch->reg_config);
+}
+
+/*
+ * pl08x_terminate_phy_chan() stops the channel, clears the FIFO and
+ * clears any pending interrupt status. This should not be used for
+ * an on-going transfer, but as a method of shutting down a channel
+ * (eg, when it's no longer used) or terminating a transfer.
+ */
+static void pl08x_terminate_phy_chan(struct pl08x_driver_data *pl08x,
+ struct pl08x_phy_chan *ch)
+{
+ u32 val;
+
+ /* The layout for the FTDMAC020 is different */
+ if (ch->ftdmac020) {
+ /* Disable all interrupts */
+ val = readl(ch->reg_config);
+ val |= (FTDMAC020_CH_CFG_INT_ABT_MASK |
+ FTDMAC020_CH_CFG_INT_ERR_MASK |
+ FTDMAC020_CH_CFG_INT_TC_MASK);
+ writel(val, ch->reg_config);
+
+ /* Abort and disable channel */
+ val = readl(ch->reg_control);
+ val &= ~FTDMAC020_CH_CSR_EN;
+ val |= FTDMAC020_CH_CSR_ABT;
+ writel(val, ch->reg_control);
+
+ /* Clear ABT and ERR interrupt flags */
+ writel(BIT(ch->id) | BIT(ch->id + 16),
+ pl08x->base + PL080_ERR_CLEAR);
+ writel(BIT(ch->id), pl08x->base + PL080_TC_CLEAR);
+
+ return;
+ }
+
+ val = readl(ch->reg_config);
+ val &= ~(PL080_CONFIG_ENABLE | PL080_CONFIG_ERR_IRQ_MASK |
+ PL080_CONFIG_TC_IRQ_MASK);
+ writel(val, ch->reg_config);
+
+ writel(BIT(ch->id), pl08x->base + PL080_ERR_CLEAR);
+ writel(BIT(ch->id), pl08x->base + PL080_TC_CLEAR);
+}
+
+static u32 get_bytes_in_phy_channel(struct pl08x_phy_chan *ch)
+{
+ u32 val;
+ u32 bytes;
+
+ if (ch->ftdmac020) {
+ bytes = readl(ch->base + FTDMAC020_CH_SIZE);
+
+ val = readl(ch->reg_control);
+ val &= FTDMAC020_CH_CSR_SRC_WIDTH_MSK;
+ val >>= FTDMAC020_CH_CSR_SRC_WIDTH_SHIFT;
+ } else if (ch->pl080s) {
+ val = readl(ch->base + PL080S_CH_CONTROL2);
+ bytes = val & PL080S_CONTROL_TRANSFER_SIZE_MASK;
+
+ val = readl(ch->reg_control);
+ val &= PL080_CONTROL_SWIDTH_MASK;
+ val >>= PL080_CONTROL_SWIDTH_SHIFT;
+ } else {
+ /* Plain PL08x */
+ val = readl(ch->reg_control);
+ bytes = val & PL080_CONTROL_TRANSFER_SIZE_MASK;
+
+ val &= PL080_CONTROL_SWIDTH_MASK;
+ val >>= PL080_CONTROL_SWIDTH_SHIFT;
+ }
+
+ switch (val) {
+ case PL080_WIDTH_8BIT:
+ break;
+ case PL080_WIDTH_16BIT:
+ bytes *= 2;
+ break;
+ case PL080_WIDTH_32BIT:
+ bytes *= 4;
+ break;
+ }
+ return bytes;
+}
+
+static u32 get_bytes_in_lli(struct pl08x_phy_chan *ch, const u32 *llis_va)
+{
+ u32 val;
+ u32 bytes;
+
+ if (ch->ftdmac020) {
+ val = llis_va[PL080_LLI_CCTL];
+ bytes = val & FTDMAC020_LLI_TRANSFER_SIZE_MASK;
+
+ val = llis_va[PL080_LLI_CCTL];
+ val &= FTDMAC020_LLI_SRC_WIDTH_MSK;
+ val >>= FTDMAC020_LLI_SRC_WIDTH_SHIFT;
+ } else if (ch->pl080s) {
+ val = llis_va[PL080S_LLI_CCTL2];
+ bytes = val & PL080S_CONTROL_TRANSFER_SIZE_MASK;
+
+ val = llis_va[PL080_LLI_CCTL];
+ val &= PL080_CONTROL_SWIDTH_MASK;
+ val >>= PL080_CONTROL_SWIDTH_SHIFT;
+ } else {
+ /* Plain PL08x */
+ val = llis_va[PL080_LLI_CCTL];
+ bytes = val & PL080_CONTROL_TRANSFER_SIZE_MASK;
+
+ val &= PL080_CONTROL_SWIDTH_MASK;
+ val >>= PL080_CONTROL_SWIDTH_SHIFT;
+ }
+
+ switch (val) {
+ case PL080_WIDTH_8BIT:
+ break;
+ case PL080_WIDTH_16BIT:
+ bytes *= 2;
+ break;
+ case PL080_WIDTH_32BIT:
+ bytes *= 4;
+ break;
+ }
+ return bytes;
+}
+
+/* The channel should be paused when calling this */
+static u32 pl08x_getbytes_chan(struct pl08x_dma_chan *plchan)
+{
+ struct pl08x_driver_data *pl08x = plchan->host;
+ const u32 *llis_va, *llis_va_limit;
+ struct pl08x_phy_chan *ch;
+ dma_addr_t llis_bus;
+ struct pl08x_txd *txd;
+ u32 llis_max_words;
+ size_t bytes;
+ u32 clli;
+
+ ch = plchan->phychan;
+ txd = plchan->at;
+
+ if (!ch || !txd)
+ return 0;
+
+ /*
+ * Follow the LLIs to get the number of remaining
+ * bytes in the currently active transaction.
+ */
+ clli = readl(ch->reg_lli) & ~PL080_LLI_LM_AHB2;
+
+ /* First get the remaining bytes in the active transfer */
+ bytes = get_bytes_in_phy_channel(ch);
+
+ if (!clli)
+ return bytes;
+
+ llis_va = txd->llis_va;
+ llis_bus = txd->llis_bus;
+
+ llis_max_words = pl08x->lli_words * MAX_NUM_TSFR_LLIS;
+ BUG_ON(clli < llis_bus || clli >= llis_bus +
+ sizeof(u32) * llis_max_words);
+
+ /*
+ * Locate the next LLI - as this is an array,
+ * it's simple maths to find.
+ */
+ llis_va += (clli - llis_bus) / sizeof(u32);
+
+ llis_va_limit = llis_va + llis_max_words;
+
+ for (; llis_va < llis_va_limit; llis_va += pl08x->lli_words) {
+ bytes += get_bytes_in_lli(ch, llis_va);
+
+ /*
+ * A LLI pointer going backward terminates the LLI list
+ */
+ if (llis_va[PL080_LLI_LLI] <= clli)
+ break;
+ }
+
+ return bytes;
+}
+
+/*
+ * Allocate a physical channel for a virtual channel
+ *
+ * Try to locate a physical channel to be used for this transfer. If all
+ * are taken return NULL and the requester will have to cope by using
+ * some fallback PIO mode or retrying later.
+ */
+static struct pl08x_phy_chan *
+pl08x_get_phy_channel(struct pl08x_driver_data *pl08x,
+ struct pl08x_dma_chan *virt_chan)
+{
+ struct pl08x_phy_chan *ch = NULL;
+ unsigned long flags;
+ int i;
+
+ for (i = 0; i < pl08x->vd->channels; i++) {
+ ch = &pl08x->phy_chans[i];
+
+ spin_lock_irqsave(&ch->lock, flags);
+
+ if (!ch->locked && !ch->serving) {
+ ch->serving = virt_chan;
+ spin_unlock_irqrestore(&ch->lock, flags);
+ break;
+ }
+
+ spin_unlock_irqrestore(&ch->lock, flags);
+ }
+
+ if (i == pl08x->vd->channels) {
+ /* No physical channel available, cope with it */
+ return NULL;
+ }
+
+ return ch;
+}
+
+/* Mark the physical channel as free. Note, this write is atomic. */
+static inline void pl08x_put_phy_channel(struct pl08x_driver_data *pl08x,
+ struct pl08x_phy_chan *ch)
+{
+ ch->serving = NULL;
+}
+
+/*
+ * Try to allocate a physical channel. When successful, assign it to
+ * this virtual channel, and initiate the next descriptor. The
+ * virtual channel lock must be held at this point.
+ */
+static void pl08x_phy_alloc_and_start(struct pl08x_dma_chan *plchan)
+{
+ struct pl08x_driver_data *pl08x = plchan->host;
+ struct pl08x_phy_chan *ch;
+
+ ch = pl08x_get_phy_channel(pl08x, plchan);
+ if (!ch) {
+ dev_dbg(&pl08x->adev->dev, "no physical channel available for xfer on %s\n", plchan->name);
+ plchan->state = PL08X_CHAN_WAITING;
+ return;
+ }
+
+ dev_dbg(&pl08x->adev->dev, "allocated physical channel %d for xfer on %s\n",
+ ch->id, plchan->name);
+
+ plchan->phychan = ch;
+ plchan->state = PL08X_CHAN_RUNNING;
+ pl08x_start_next_txd(plchan);
+}
+
+static void pl08x_phy_reassign_start(struct pl08x_phy_chan *ch,
+ struct pl08x_dma_chan *plchan)
+{
+ struct pl08x_driver_data *pl08x = plchan->host;
+
+ dev_dbg(&pl08x->adev->dev, "reassigned physical channel %d for xfer on %s\n",
+ ch->id, plchan->name);
+
+ /*
+ * We do this without taking the lock; we're really only concerned
+ * about whether this pointer is NULL or not, and we're guaranteed
+ * that this will only be called when it _already_ is non-NULL.
+ */
+ ch->serving = plchan;
+ plchan->phychan = ch;
+ plchan->state = PL08X_CHAN_RUNNING;
+ pl08x_start_next_txd(plchan);
+}
+
+/*
+ * Free a physical DMA channel, potentially reallocating it to another
+ * virtual channel if we have any pending.
+ */
+static void pl08x_phy_free(struct pl08x_dma_chan *plchan)
+{
+ struct pl08x_driver_data *pl08x = plchan->host;
+ struct pl08x_dma_chan *p, *next;
+
+ retry:
+ next = NULL;
+
+ /* Find a waiting virtual channel for the next transfer. */
+ list_for_each_entry(p, &pl08x->memcpy.channels, vc.chan.device_node)
+ if (p->state == PL08X_CHAN_WAITING) {
+ next = p;
+ break;
+ }
+
+ if (!next && pl08x->has_slave) {
+ list_for_each_entry(p, &pl08x->slave.channels, vc.chan.device_node)
+ if (p->state == PL08X_CHAN_WAITING) {
+ next = p;
+ break;
+ }
+ }
+
+ /* Ensure that the physical channel is stopped */
+ pl08x_terminate_phy_chan(pl08x, plchan->phychan);
+
+ if (next) {
+ bool success;
+
+ /*
+ * Eww. We know this isn't going to deadlock
+ * but lockdep probably doesn't.
+ */
+ spin_lock(&next->vc.lock);
+ /* Re-check the state now that we have the lock */
+ success = next->state == PL08X_CHAN_WAITING;
+ if (success)
+ pl08x_phy_reassign_start(plchan->phychan, next);
+ spin_unlock(&next->vc.lock);
+
+ /* If the state changed, try to find another channel */
+ if (!success)
+ goto retry;
+ } else {
+ /* No more jobs, so free up the physical channel */
+ pl08x_put_phy_channel(pl08x, plchan->phychan);
+ }
+
+ plchan->phychan = NULL;
+ plchan->state = PL08X_CHAN_IDLE;
+}
+
+/*
+ * LLI handling
+ */
+
+static inline unsigned int
+pl08x_get_bytes_for_lli(struct pl08x_driver_data *pl08x,
+ u32 cctl,
+ bool source)
+{
+ u32 val;
+
+ if (pl08x->vd->ftdmac020) {
+ if (source)
+ val = (cctl & FTDMAC020_LLI_SRC_WIDTH_MSK) >>
+ FTDMAC020_LLI_SRC_WIDTH_SHIFT;
+ else
+ val = (cctl & FTDMAC020_LLI_DST_WIDTH_MSK) >>
+ FTDMAC020_LLI_DST_WIDTH_SHIFT;
+ } else {
+ if (source)
+ val = (cctl & PL080_CONTROL_SWIDTH_MASK) >>
+ PL080_CONTROL_SWIDTH_SHIFT;
+ else
+ val = (cctl & PL080_CONTROL_DWIDTH_MASK) >>
+ PL080_CONTROL_DWIDTH_SHIFT;
+ }
+
+ switch (val) {
+ case PL080_WIDTH_8BIT:
+ return 1;
+ case PL080_WIDTH_16BIT:
+ return 2;
+ case PL080_WIDTH_32BIT:
+ return 4;
+ default:
+ break;
+ }
+ BUG();
+ return 0;
+}
+
+static inline u32 pl08x_lli_control_bits(struct pl08x_driver_data *pl08x,
+ u32 cctl,
+ u8 srcwidth, u8 dstwidth,
+ size_t tsize)
+{
+ u32 retbits = cctl;
+
+ /*
+ * Remove all src, dst and transfer size bits, then set the
+ * width and size according to the parameters. The bit offsets
+ * are different in the FTDMAC020 so we need to accound for this.
+ */
+ if (pl08x->vd->ftdmac020) {
+ retbits &= ~FTDMAC020_LLI_DST_WIDTH_MSK;
+ retbits &= ~FTDMAC020_LLI_SRC_WIDTH_MSK;
+ retbits &= ~FTDMAC020_LLI_TRANSFER_SIZE_MASK;
+
+ switch (srcwidth) {
+ case 1:
+ retbits |= PL080_WIDTH_8BIT <<
+ FTDMAC020_LLI_SRC_WIDTH_SHIFT;
+ break;
+ case 2:
+ retbits |= PL080_WIDTH_16BIT <<
+ FTDMAC020_LLI_SRC_WIDTH_SHIFT;
+ break;
+ case 4:
+ retbits |= PL080_WIDTH_32BIT <<
+ FTDMAC020_LLI_SRC_WIDTH_SHIFT;
+ break;
+ default:
+ BUG();
+ break;
+ }
+
+ switch (dstwidth) {
+ case 1:
+ retbits |= PL080_WIDTH_8BIT <<
+ FTDMAC020_LLI_DST_WIDTH_SHIFT;
+ break;
+ case 2:
+ retbits |= PL080_WIDTH_16BIT <<
+ FTDMAC020_LLI_DST_WIDTH_SHIFT;
+ break;
+ case 4:
+ retbits |= PL080_WIDTH_32BIT <<
+ FTDMAC020_LLI_DST_WIDTH_SHIFT;
+ break;
+ default:
+ BUG();
+ break;
+ }
+
+ tsize &= FTDMAC020_LLI_TRANSFER_SIZE_MASK;
+ retbits |= tsize << FTDMAC020_LLI_TRANSFER_SIZE_SHIFT;
+ } else {
+ retbits &= ~PL080_CONTROL_DWIDTH_MASK;
+ retbits &= ~PL080_CONTROL_SWIDTH_MASK;
+ retbits &= ~PL080_CONTROL_TRANSFER_SIZE_MASK;
+
+ switch (srcwidth) {
+ case 1:
+ retbits |= PL080_WIDTH_8BIT <<
+ PL080_CONTROL_SWIDTH_SHIFT;
+ break;
+ case 2:
+ retbits |= PL080_WIDTH_16BIT <<
+ PL080_CONTROL_SWIDTH_SHIFT;
+ break;
+ case 4:
+ retbits |= PL080_WIDTH_32BIT <<
+ PL080_CONTROL_SWIDTH_SHIFT;
+ break;
+ default:
+ BUG();
+ break;
+ }
+
+ switch (dstwidth) {
+ case 1:
+ retbits |= PL080_WIDTH_8BIT <<
+ PL080_CONTROL_DWIDTH_SHIFT;
+ break;
+ case 2:
+ retbits |= PL080_WIDTH_16BIT <<
+ PL080_CONTROL_DWIDTH_SHIFT;
+ break;
+ case 4:
+ retbits |= PL080_WIDTH_32BIT <<
+ PL080_CONTROL_DWIDTH_SHIFT;
+ break;
+ default:
+ BUG();
+ break;
+ }
+
+ tsize &= PL080_CONTROL_TRANSFER_SIZE_MASK;
+ retbits |= tsize << PL080_CONTROL_TRANSFER_SIZE_SHIFT;
+ }
+
+ return retbits;
+}
+
+struct pl08x_lli_build_data {
+ struct pl08x_txd *txd;
+ struct pl08x_bus_data srcbus;
+ struct pl08x_bus_data dstbus;
+ size_t remainder;
+ u32 lli_bus;
+};
+
+/*
+ * Autoselect a master bus to use for the transfer. Slave will be the chosen as
+ * victim in case src & dest are not similarly aligned. i.e. If after aligning
+ * masters address with width requirements of transfer (by sending few byte by
+ * byte data), slave is still not aligned, then its width will be reduced to
+ * BYTE.
+ * - prefers the destination bus if both available
+ * - prefers bus with fixed address (i.e. peripheral)
+ */
+static void pl08x_choose_master_bus(struct pl08x_driver_data *pl08x,
+ struct pl08x_lli_build_data *bd,
+ struct pl08x_bus_data **mbus,
+ struct pl08x_bus_data **sbus,
+ u32 cctl)
+{
+ bool dst_incr;
+ bool src_incr;
+
+ /*
+ * The FTDMAC020 only supports memory-to-memory transfer, so
+ * source and destination always increase.
+ */
+ if (pl08x->vd->ftdmac020) {
+ dst_incr = true;
+ src_incr = true;
+ } else {
+ dst_incr = !!(cctl & PL080_CONTROL_DST_INCR);
+ src_incr = !!(cctl & PL080_CONTROL_SRC_INCR);
+ }
+
+ /*
+ * If either bus is not advancing, i.e. it is a peripheral, that
+ * one becomes master
+ */
+ if (!dst_incr) {
+ *mbus = &bd->dstbus;
+ *sbus = &bd->srcbus;
+ } else if (!src_incr) {
+ *mbus = &bd->srcbus;
+ *sbus = &bd->dstbus;
+ } else {
+ if (bd->dstbus.buswidth >= bd->srcbus.buswidth) {
+ *mbus = &bd->dstbus;
+ *sbus = &bd->srcbus;
+ } else {
+ *mbus = &bd->srcbus;
+ *sbus = &bd->dstbus;
+ }
+ }
+}
+
+/*
+ * Fills in one LLI for a certain transfer descriptor and advance the counter
+ */
+static void pl08x_fill_lli_for_desc(struct pl08x_driver_data *pl08x,
+ struct pl08x_lli_build_data *bd,
+ int num_llis, int len, u32 cctl, u32 cctl2)
+{
+ u32 offset = num_llis * pl08x->lli_words;
+ u32 *llis_va = bd->txd->llis_va + offset;
+ dma_addr_t llis_bus = bd->txd->llis_bus;
+
+ BUG_ON(num_llis >= MAX_NUM_TSFR_LLIS);
+
+ /* Advance the offset to next LLI. */
+ offset += pl08x->lli_words;
+
+ llis_va[PL080_LLI_SRC] = bd->srcbus.addr;
+ llis_va[PL080_LLI_DST] = bd->dstbus.addr;
+ llis_va[PL080_LLI_LLI] = (llis_bus + sizeof(u32) * offset);
+ llis_va[PL080_LLI_LLI] |= bd->lli_bus;
+ llis_va[PL080_LLI_CCTL] = cctl;
+ if (pl08x->vd->pl080s)
+ llis_va[PL080S_LLI_CCTL2] = cctl2;
+
+ if (pl08x->vd->ftdmac020) {
+ /* FIXME: only memcpy so far so both increase */
+ bd->srcbus.addr += len;
+ bd->dstbus.addr += len;
+ } else {
+ if (cctl & PL080_CONTROL_SRC_INCR)
+ bd->srcbus.addr += len;
+ if (cctl & PL080_CONTROL_DST_INCR)
+ bd->dstbus.addr += len;
+ }
+
+ BUG_ON(bd->remainder < len);
+
+ bd->remainder -= len;
+}
+
+static inline void prep_byte_width_lli(struct pl08x_driver_data *pl08x,
+ struct pl08x_lli_build_data *bd, u32 *cctl, u32 len,
+ int num_llis, size_t *total_bytes)
+{
+ *cctl = pl08x_lli_control_bits(pl08x, *cctl, 1, 1, len);
+ pl08x_fill_lli_for_desc(pl08x, bd, num_llis, len, *cctl, len);
+ (*total_bytes) += len;
+}
+
+#if 1
+static void pl08x_dump_lli(struct pl08x_driver_data *pl08x,
+ const u32 *llis_va, int num_llis)
+{
+ int i;
+
+ if (pl08x->vd->pl080s) {
+ dev_vdbg(&pl08x->adev->dev,
+ "%-3s %-9s %-10s %-10s %-10s %-10s %s\n",
+ "lli", "", "csrc", "cdst", "clli", "cctl", "cctl2");
+ for (i = 0; i < num_llis; i++) {
+ dev_vdbg(&pl08x->adev->dev,
+ "%3d @%p: 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x\n",
+ i, llis_va, llis_va[PL080_LLI_SRC],
+ llis_va[PL080_LLI_DST], llis_va[PL080_LLI_LLI],
+ llis_va[PL080_LLI_CCTL],
+ llis_va[PL080S_LLI_CCTL2]);
+ llis_va += pl08x->lli_words;
+ }
+ } else {
+ dev_vdbg(&pl08x->adev->dev,
+ "%-3s %-9s %-10s %-10s %-10s %s\n",
+ "lli", "", "csrc", "cdst", "clli", "cctl");
+ for (i = 0; i < num_llis; i++) {
+ dev_vdbg(&pl08x->adev->dev,
+ "%3d @%p: 0x%08x 0x%08x 0x%08x 0x%08x\n",
+ i, llis_va, llis_va[PL080_LLI_SRC],
+ llis_va[PL080_LLI_DST], llis_va[PL080_LLI_LLI],
+ llis_va[PL080_LLI_CCTL]);
+ llis_va += pl08x->lli_words;
+ }
+ }
+}
+#else
+static inline void pl08x_dump_lli(struct pl08x_driver_data *pl08x,
+ const u32 *llis_va, int num_llis) {}
+#endif
+
+/*
+ * This fills in the table of LLIs for the transfer descriptor
+ * Note that we assume we never have to change the burst sizes
+ * Return 0 for error
+ */
+static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
+ struct pl08x_txd *txd)
+{
+ struct pl08x_bus_data *mbus, *sbus;
+ struct pl08x_lli_build_data bd;
+ int num_llis = 0;
+ u32 cctl, early_bytes = 0;
+ size_t max_bytes_per_lli, total_bytes;
+ u32 *llis_va, *last_lli;
+ struct pl08x_sg *dsg;
+
+ txd->llis_va = dma_pool_alloc(pl08x->pool, GFP_NOWAIT, &txd->llis_bus);
+ if (!txd->llis_va) {
+ dev_err(&pl08x->adev->dev, "%s no memory for llis\n", __func__);
+ return 0;
+ }
+
+ bd.txd = txd;
+ bd.lli_bus = (pl08x->lli_buses & PL08X_AHB2) ? PL080_LLI_LM_AHB2 : 0;
+ cctl = txd->cctl;
+
+ /* Find maximum width of the source bus */
+ bd.srcbus.maxwidth = pl08x_get_bytes_for_lli(pl08x, cctl, true);
+
+ /* Find maximum width of the destination bus */
+ bd.dstbus.maxwidth = pl08x_get_bytes_for_lli(pl08x, cctl, false);
+
+ list_for_each_entry(dsg, &txd->dsg_list, node) {
+ total_bytes = 0;
+ cctl = txd->cctl;
+
+ bd.srcbus.addr = dsg->src_addr;
+ bd.dstbus.addr = dsg->dst_addr;
+ bd.remainder = dsg->len;
+ bd.srcbus.buswidth = bd.srcbus.maxwidth;
+ bd.dstbus.buswidth = bd.dstbus.maxwidth;
+
+ pl08x_choose_master_bus(pl08x, &bd, &mbus, &sbus, cctl);
+
+ dev_vdbg(&pl08x->adev->dev,
+ "src=0x%08llx%s/%u dst=0x%08llx%s/%u len=%zu\n",
+ (u64)bd.srcbus.addr,
+ cctl & PL080_CONTROL_SRC_INCR ? "+" : "",
+ bd.srcbus.buswidth,
+ (u64)bd.dstbus.addr,
+ cctl & PL080_CONTROL_DST_INCR ? "+" : "",
+ bd.dstbus.buswidth,
+ bd.remainder);
+ dev_vdbg(&pl08x->adev->dev, "mbus=%s sbus=%s\n",
+ mbus == &bd.srcbus ? "src" : "dst",
+ sbus == &bd.srcbus ? "src" : "dst");
+
+ /*
+ * Zero length is only allowed if all these requirements are
+ * met:
+ * - flow controller is peripheral.
+ * - src.addr is aligned to src.width
+ * - dst.addr is aligned to dst.width
+ *
+ * sg_len == 1 should be true, as there can be two cases here:
+ *
+ * - Memory addresses are contiguous and are not scattered.
+ * Here, Only one sg will be passed by user driver, with
+ * memory address and zero length. We pass this to controller
+ * and after the transfer it will receive the last burst
+ * request from peripheral and so transfer finishes.
+ *
+ * - Memory addresses are scattered and are not contiguous.
+ * Here, Obviously as DMA controller doesn't know when a lli's
+ * transfer gets over, it can't load next lli. So in this
+ * case, there has to be an assumption that only one lli is
+ * supported. Thus, we can't have scattered addresses.
+ */
+ if (!bd.remainder) {
+ u32 fc;
+
+ /* FTDMAC020 only does memory-to-memory */
+ if (pl08x->vd->ftdmac020)
+ fc = PL080_FLOW_MEM2MEM;
+ else
+ fc = (txd->ccfg & PL080_CONFIG_FLOW_CONTROL_MASK) >>
+ PL080_CONFIG_FLOW_CONTROL_SHIFT;
+ if (!((fc >= PL080_FLOW_SRC2DST_DST) &&
+ (fc <= PL080_FLOW_SRC2DST_SRC))) {
+ dev_err(&pl08x->adev->dev, "%s sg len can't be zero",
+ __func__);
+ return 0;
+ }
+
+ if (!IS_BUS_ALIGNED(&bd.srcbus) ||
+ !IS_BUS_ALIGNED(&bd.dstbus)) {
+ dev_err(&pl08x->adev->dev,
+ "%s src & dst address must be aligned to src"
+ " & dst width if peripheral is flow controller",
+ __func__);
+ return 0;
+ }
+
+ cctl = pl08x_lli_control_bits(pl08x, cctl,
+ bd.srcbus.buswidth, bd.dstbus.buswidth,
+ 0);
+ pl08x_fill_lli_for_desc(pl08x, &bd, num_llis++,
+ 0, cctl, 0);
+ break;
+ }
+
+ /*
+ * Send byte by byte for following cases
+ * - Less than a bus width available
+ * - until master bus is aligned
+ */
+ if (bd.remainder < mbus->buswidth)
+ early_bytes = bd.remainder;
+ else if (!IS_BUS_ALIGNED(mbus)) {
+ early_bytes = mbus->buswidth -
+ (mbus->addr & (mbus->buswidth - 1));
+ if ((bd.remainder - early_bytes) < mbus->buswidth)
+ early_bytes = bd.remainder;
+ }
+
+ if (early_bytes) {
+ dev_vdbg(&pl08x->adev->dev,
+ "%s byte width LLIs (remain 0x%08zx)\n",
+ __func__, bd.remainder);
+ prep_byte_width_lli(pl08x, &bd, &cctl, early_bytes,
+ num_llis++, &total_bytes);
+ }
+
+ if (bd.remainder) {
+ /*
+ * Master now aligned
+ * - if slave is not then we must set its width down
+ */
+ if (!IS_BUS_ALIGNED(sbus)) {
+ dev_dbg(&pl08x->adev->dev,
+ "%s set down bus width to one byte\n",
+ __func__);
+
+ sbus->buswidth = 1;
+ }
+
+ /*
+ * Bytes transferred = tsize * src width, not
+ * MIN(buswidths)
+ */
+ max_bytes_per_lli = bd.srcbus.buswidth *
+ pl08x->vd->max_transfer_size;
+ dev_vdbg(&pl08x->adev->dev,
+ "%s max bytes per lli = %zu\n",
+ __func__, max_bytes_per_lli);
+
+ /*
+ * Make largest possible LLIs until less than one bus
+ * width left
+ */
+ while (bd.remainder > (mbus->buswidth - 1)) {
+ size_t lli_len, tsize, width;
+
+ /*
+ * If enough left try to send max possible,
+ * otherwise try to send the remainder
+ */
+ lli_len = min(bd.remainder, max_bytes_per_lli);
+
+ /*
+ * Check against maximum bus alignment:
+ * Calculate actual transfer size in relation to
+ * bus width an get a maximum remainder of the
+ * highest bus width - 1
+ */
+ width = max(mbus->buswidth, sbus->buswidth);
+ lli_len = (lli_len / width) * width;
+ tsize = lli_len / bd.srcbus.buswidth;
+
+ dev_vdbg(&pl08x->adev->dev,
+ "%s fill lli with single lli chunk of "
+ "size 0x%08zx (remainder 0x%08zx)\n",
+ __func__, lli_len, bd.remainder);
+
+ cctl = pl08x_lli_control_bits(pl08x, cctl,
+ bd.srcbus.buswidth, bd.dstbus.buswidth,
+ tsize);
+ pl08x_fill_lli_for_desc(pl08x, &bd, num_llis++,
+ lli_len, cctl, tsize);
+ total_bytes += lli_len;
+ }
+
+ /*
+ * Send any odd bytes
+ */
+ if (bd.remainder) {
+ dev_vdbg(&pl08x->adev->dev,
+ "%s align with boundary, send odd bytes (remain %zu)\n",
+ __func__, bd.remainder);
+ prep_byte_width_lli(pl08x, &bd, &cctl,
+ bd.remainder, num_llis++, &total_bytes);
+ }
+ }
+
+ if (total_bytes != dsg->len) {
+ dev_err(&pl08x->adev->dev,
+ "%s size of encoded lli:s don't match total txd, transferred 0x%08zx from size 0x%08zx\n",
+ __func__, total_bytes, dsg->len);
+ return 0;
+ }
+
+ if (num_llis >= MAX_NUM_TSFR_LLIS) {
+ dev_err(&pl08x->adev->dev,
+ "%s need to increase MAX_NUM_TSFR_LLIS from 0x%08x\n",
+ __func__, MAX_NUM_TSFR_LLIS);
+ return 0;
+ }
+ }
+
+ llis_va = txd->llis_va;
+ last_lli = llis_va + (num_llis - 1) * pl08x->lli_words;
+
+ if (txd->cyclic) {
+ /* Link back to the first LLI. */
+ last_lli[PL080_LLI_LLI] = txd->llis_bus | bd.lli_bus;
+ } else {
+ /* The final LLI terminates the LLI. */
+ last_lli[PL080_LLI_LLI] = 0;
+ /* The final LLI element shall also fire an interrupt. */
+ if (pl08x->vd->ftdmac020)
+ last_lli[PL080_LLI_CCTL] &= ~FTDMAC020_LLI_TC_MSK;
+ else
+ last_lli[PL080_LLI_CCTL] |= PL080_CONTROL_TC_IRQ_EN;
+ }
+
+ pl08x_dump_lli(pl08x, llis_va, num_llis);
+
+ return num_llis;
+}
+
+static void pl08x_free_txd(struct pl08x_driver_data *pl08x,
+ struct pl08x_txd *txd)
+{
+ struct pl08x_sg *dsg, *_dsg;
+
+ if (txd->llis_va)
+ dma_pool_free(pl08x->pool, txd->llis_va, txd->llis_bus);
+
+ list_for_each_entry_safe(dsg, _dsg, &txd->dsg_list, node) {
+ list_del(&dsg->node);
+ kfree(dsg);
+ }
+
+ kfree(txd);
+}
+
+static void pl08x_desc_free(struct virt_dma_desc *vd)
+{
+ struct pl08x_txd *txd = to_pl08x_txd(&vd->tx);
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(vd->tx.chan);
+
+ dma_descriptor_unmap(&vd->tx);
+ if (!txd->done)
+ pl08x_release_mux(plchan);
+
+ pl08x_free_txd(plchan->host, txd);
+}
+
+static void pl08x_free_txd_list(struct pl08x_driver_data *pl08x,
+ struct pl08x_dma_chan *plchan)
+{
+ LIST_HEAD(head);
+
+ vchan_get_all_descriptors(&plchan->vc, &head);
+ vchan_dma_desc_free_list(&plchan->vc, &head);
+}
+
+/*
+ * The DMA ENGINE API
+ */
+static void pl08x_free_chan_resources(struct dma_chan *chan)
+{
+ /* Ensure all queued descriptors are freed */
+ vchan_free_chan_resources(to_virt_chan(chan));
+}
+
+static struct dma_async_tx_descriptor *pl08x_prep_dma_interrupt(
+ struct dma_chan *chan, unsigned long flags)
+{
+ struct dma_async_tx_descriptor *retval = NULL;
+
+ return retval;
+}
+
+/*
+ * Code accessing dma_async_is_complete() in a tight loop may give problems.
+ * If slaves are relying on interrupts to signal completion this function
+ * must not be called with interrupts disabled.
+ */
+static enum dma_status pl08x_dma_tx_status(struct dma_chan *chan,
+ dma_cookie_t cookie, struct dma_tx_state *txstate)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+ struct virt_dma_desc *vd;
+ unsigned long flags;
+ enum dma_status ret;
+ size_t bytes = 0;
+
+ ret = dma_cookie_status(chan, cookie, txstate);
+ if (ret == DMA_COMPLETE)
+ return ret;
+
+ /*
+ * There's no point calculating the residue if there's
+ * no txstate to store the value.
+ */
+ if (!txstate) {
+ if (plchan->state == PL08X_CHAN_PAUSED)
+ ret = DMA_PAUSED;
+ return ret;
+ }
+
+ spin_lock_irqsave(&plchan->vc.lock, flags);
+ ret = dma_cookie_status(chan, cookie, txstate);
+ if (ret != DMA_COMPLETE) {
+ vd = vchan_find_desc(&plchan->vc, cookie);
+ if (vd) {
+ /* On the issued list, so hasn't been processed yet */
+ struct pl08x_txd *txd = to_pl08x_txd(&vd->tx);
+ struct pl08x_sg *dsg;
+
+ list_for_each_entry(dsg, &txd->dsg_list, node)
+ bytes += dsg->len;
+ } else {
+ bytes = pl08x_getbytes_chan(plchan);
+ }
+ }
+ spin_unlock_irqrestore(&plchan->vc.lock, flags);
+
+ /*
+ * This cookie not complete yet
+ * Get number of bytes left in the active transactions and queue
+ */
+ dma_set_residue(txstate, bytes);
+
+ if (plchan->state == PL08X_CHAN_PAUSED && ret == DMA_IN_PROGRESS)
+ ret = DMA_PAUSED;
+
+ /* Whether waiting or running, we're in progress */
+ return ret;
+}
+
+/* PrimeCell DMA extension */
+struct burst_table {
+ u32 burstwords;
+ u32 reg;
+};
+
+static const struct burst_table burst_sizes[] = {
+ {
+ .burstwords = 256,
+ .reg = PL080_BSIZE_256,
+ },
+ {
+ .burstwords = 128,
+ .reg = PL080_BSIZE_128,
+ },
+ {
+ .burstwords = 64,
+ .reg = PL080_BSIZE_64,
+ },
+ {
+ .burstwords = 32,
+ .reg = PL080_BSIZE_32,
+ },
+ {
+ .burstwords = 16,
+ .reg = PL080_BSIZE_16,
+ },
+ {
+ .burstwords = 8,
+ .reg = PL080_BSIZE_8,
+ },
+ {
+ .burstwords = 4,
+ .reg = PL080_BSIZE_4,
+ },
+ {
+ .burstwords = 0,
+ .reg = PL080_BSIZE_1,
+ },
+};
+
+/*
+ * Given the source and destination available bus masks, select which
+ * will be routed to each port. We try to have source and destination
+ * on separate ports, but always respect the allowable settings.
+ */
+static u32 pl08x_select_bus(bool ftdmac020, u8 src, u8 dst)
+{
+ u32 cctl = 0;
+ u32 dst_ahb2;
+ u32 src_ahb2;
+
+ /* The FTDMAC020 use different bits to indicate src/dst bus */
+ if (ftdmac020) {
+ dst_ahb2 = FTDMAC020_LLI_DST_SEL;
+ src_ahb2 = FTDMAC020_LLI_SRC_SEL;
+ } else {
+ dst_ahb2 = PL080_CONTROL_DST_AHB2;
+ src_ahb2 = PL080_CONTROL_SRC_AHB2;
+ }
+
+ if (!(dst & PL08X_AHB1) || ((dst & PL08X_AHB2) && (src & PL08X_AHB1)))
+ cctl |= dst_ahb2;
+ if (!(src & PL08X_AHB1) || ((src & PL08X_AHB2) && !(dst & PL08X_AHB2)))
+ cctl |= src_ahb2;
+
+ return cctl;
+}
+
+static u32 pl08x_cctl(u32 cctl)
+{
+ cctl &= ~(PL080_CONTROL_SRC_AHB2 | PL080_CONTROL_DST_AHB2 |
+ PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR |
+ PL080_CONTROL_PROT_MASK);
+
+ /* Access the cell in privileged mode, non-bufferable, non-cacheable */
+ return cctl | PL080_CONTROL_PROT_SYS;
+}
+
+static u32 pl08x_width(enum dma_slave_buswidth width)
+{
+ switch (width) {
+ case DMA_SLAVE_BUSWIDTH_1_BYTE:
+ return PL080_WIDTH_8BIT;
+ case DMA_SLAVE_BUSWIDTH_2_BYTES:
+ return PL080_WIDTH_16BIT;
+ case DMA_SLAVE_BUSWIDTH_4_BYTES:
+ return PL080_WIDTH_32BIT;
+ default:
+ return ~0;
+ }
+}
+
+static u32 pl08x_burst(u32 maxburst)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(burst_sizes); i++)
+ if (burst_sizes[i].burstwords <= maxburst)
+ break;
+
+ return burst_sizes[i].reg;
+}
+
+static u32 pl08x_get_cctl(struct pl08x_dma_chan *plchan,
+ enum dma_slave_buswidth addr_width, u32 maxburst)
+{
+ u32 width, burst, cctl = 0;
+
+ width = pl08x_width(addr_width);
+ if (width == ~0)
+ return ~0;
+
+ cctl |= width << PL080_CONTROL_SWIDTH_SHIFT;
+ cctl |= width << PL080_CONTROL_DWIDTH_SHIFT;
+
+ /*
+ * If this channel will only request single transfers, set this
+ * down to ONE element. Also select one element if no maxburst
+ * is specified.
+ */
+ if (plchan->cd->single)
+ maxburst = 1;
+
+ burst = pl08x_burst(maxburst);
+ cctl |= burst << PL080_CONTROL_SB_SIZE_SHIFT;
+ cctl |= burst << PL080_CONTROL_DB_SIZE_SHIFT;
+
+ return pl08x_cctl(cctl);
+}
+
+/*
+ * Slave transactions callback to the slave device to allow
+ * synchronization of slave DMA signals with the DMAC enable
+ */
+static void pl08x_issue_pending(struct dma_chan *chan)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+ unsigned long flags;
+
+ spin_lock_irqsave(&plchan->vc.lock, flags);
+ if (vchan_issue_pending(&plchan->vc)) {
+ if (!plchan->phychan && plchan->state != PL08X_CHAN_WAITING)
+ pl08x_phy_alloc_and_start(plchan);
+ }
+ spin_unlock_irqrestore(&plchan->vc.lock, flags);
+}
+
+static struct pl08x_txd *pl08x_get_txd(struct pl08x_dma_chan *plchan)
+{
+ struct pl08x_txd *txd = kzalloc(sizeof(*txd), GFP_NOWAIT);
+
+ if (txd)
+ INIT_LIST_HEAD(&txd->dsg_list);
+ return txd;
+}
+
+static u32 pl08x_memcpy_cctl(struct pl08x_driver_data *pl08x)
+{
+ u32 cctl = 0;
+
+ /* Conjure cctl */
+ switch (pl08x->pd->memcpy_burst_size) {
+ default:
+ dev_err(&pl08x->adev->dev,
+ "illegal burst size for memcpy, set to 1\n");
+ /* Fall through */
+ case PL08X_BURST_SZ_1:
+ cctl |= PL080_BSIZE_1 << PL080_CONTROL_SB_SIZE_SHIFT |
+ PL080_BSIZE_1 << PL080_CONTROL_DB_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_4:
+ cctl |= PL080_BSIZE_4 << PL080_CONTROL_SB_SIZE_SHIFT |
+ PL080_BSIZE_4 << PL080_CONTROL_DB_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_8:
+ cctl |= PL080_BSIZE_8 << PL080_CONTROL_SB_SIZE_SHIFT |
+ PL080_BSIZE_8 << PL080_CONTROL_DB_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_16:
+ cctl |= PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT |
+ PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_32:
+ cctl |= PL080_BSIZE_32 << PL080_CONTROL_SB_SIZE_SHIFT |
+ PL080_BSIZE_32 << PL080_CONTROL_DB_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_64:
+ cctl |= PL080_BSIZE_64 << PL080_CONTROL_SB_SIZE_SHIFT |
+ PL080_BSIZE_64 << PL080_CONTROL_DB_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_128:
+ cctl |= PL080_BSIZE_128 << PL080_CONTROL_SB_SIZE_SHIFT |
+ PL080_BSIZE_128 << PL080_CONTROL_DB_SIZE_SHIFT;
+ break;
+ case PL08X_BURST_SZ_256:
+ cctl |= PL080_BSIZE_256 << PL080_CONTROL_SB_SIZE_SHIFT |
+ PL080_BSIZE_256 << PL080_CONTROL_DB_SIZE_SHIFT;
+ break;
+ }
+
+ switch (pl08x->pd->memcpy_bus_width) {
+ default:
+ dev_err(&pl08x->adev->dev,
+ "illegal bus width for memcpy, set to 8 bits\n");
+ /* Fall through */
+ case PL08X_BUS_WIDTH_8_BITS:
+ cctl |= PL080_WIDTH_8BIT << PL080_CONTROL_SWIDTH_SHIFT |
+ PL080_WIDTH_8BIT << PL080_CONTROL_DWIDTH_SHIFT;
+ break;
+ case PL08X_BUS_WIDTH_16_BITS:
+ cctl |= PL080_WIDTH_16BIT << PL080_CONTROL_SWIDTH_SHIFT |
+ PL080_WIDTH_16BIT << PL080_CONTROL_DWIDTH_SHIFT;
+ break;
+ case PL08X_BUS_WIDTH_32_BITS:
+ cctl |= PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT |
+ PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT;
+ break;
+ }
+
+ /* Protection flags */
+ if (pl08x->pd->memcpy_prot_buff)
+ cctl |= PL080_CONTROL_PROT_BUFF;
+ if (pl08x->pd->memcpy_prot_cache)
+ cctl |= PL080_CONTROL_PROT_CACHE;
+
+ /* We are the kernel, so we are in privileged mode */
+ cctl |= PL080_CONTROL_PROT_SYS;
+
+ /* Both to be incremented or the code will break */
+ cctl |= PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR;
+
+ if (pl08x->vd->dualmaster)
+ cctl |= pl08x_select_bus(false,
+ pl08x->mem_buses,
+ pl08x->mem_buses);
+
+ return cctl;
+}
+
+static u32 pl08x_ftdmac020_memcpy_cctl(struct pl08x_driver_data *pl08x)
+{
+ u32 cctl = 0;
+
+ /* Conjure cctl */
+ switch (pl08x->pd->memcpy_bus_width) {
+ default:
+ dev_err(&pl08x->adev->dev,
+ "illegal bus width for memcpy, set to 8 bits\n");
+ /* Fall through */
+ case PL08X_BUS_WIDTH_8_BITS:
+ cctl |= PL080_WIDTH_8BIT << FTDMAC020_LLI_SRC_WIDTH_SHIFT |
+ PL080_WIDTH_8BIT << FTDMAC020_LLI_DST_WIDTH_SHIFT;
+ break;
+ case PL08X_BUS_WIDTH_16_BITS:
+ cctl |= PL080_WIDTH_16BIT << FTDMAC020_LLI_SRC_WIDTH_SHIFT |
+ PL080_WIDTH_16BIT << FTDMAC020_LLI_DST_WIDTH_SHIFT;
+ break;
+ case PL08X_BUS_WIDTH_32_BITS:
+ cctl |= PL080_WIDTH_32BIT << FTDMAC020_LLI_SRC_WIDTH_SHIFT |
+ PL080_WIDTH_32BIT << FTDMAC020_LLI_DST_WIDTH_SHIFT;
+ break;
+ }
+
+ /*
+ * By default mask the TC IRQ on all LLIs, it will be unmasked on
+ * the last LLI item by other code.
+ */
+ cctl |= FTDMAC020_LLI_TC_MSK;
+
+ /*
+ * Both to be incremented so leave bits FTDMAC020_LLI_SRCAD_CTL
+ * and FTDMAC020_LLI_DSTAD_CTL as zero
+ */
+ if (pl08x->vd->dualmaster)
+ cctl |= pl08x_select_bus(true,
+ pl08x->mem_buses,
+ pl08x->mem_buses);
+
+ return cctl;
+}
+
+/*
+ * Initialize a descriptor to be used by memcpy submit
+ */
+static struct dma_async_tx_descriptor *pl08x_prep_dma_memcpy(
+ struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
+ size_t len, unsigned long flags)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+ struct pl08x_driver_data *pl08x = plchan->host;
+ struct pl08x_txd *txd;
+ struct pl08x_sg *dsg;
+ int ret;
+
+ txd = pl08x_get_txd(plchan);
+ if (!txd) {
+ dev_err(&pl08x->adev->dev,
+ "%s no memory for descriptor\n", __func__);
+ return NULL;
+ }
+
+ dsg = kzalloc(sizeof(struct pl08x_sg), GFP_NOWAIT);
+ if (!dsg) {
+ pl08x_free_txd(pl08x, txd);
+ return NULL;
+ }
+ list_add_tail(&dsg->node, &txd->dsg_list);
+
+ dsg->src_addr = src;
+ dsg->dst_addr = dest;
+ dsg->len = len;
+ if (pl08x->vd->ftdmac020) {
+ /* Writing CCFG zero ENABLES all interrupts */
+ txd->ccfg = 0;
+ txd->cctl = pl08x_ftdmac020_memcpy_cctl(pl08x);
+ } else {
+ txd->ccfg = PL080_CONFIG_ERR_IRQ_MASK |
+ PL080_CONFIG_TC_IRQ_MASK |
+ PL080_FLOW_MEM2MEM << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+ txd->cctl = pl08x_memcpy_cctl(pl08x);
+ }
+
+ ret = pl08x_fill_llis_for_desc(plchan->host, txd);
+ if (!ret) {
+ pl08x_free_txd(pl08x, txd);
+ return NULL;
+ }
+
+ return vchan_tx_prep(&plchan->vc, &txd->vd, flags);
+}
+
+static struct pl08x_txd *pl08x_init_txd(
+ struct dma_chan *chan,
+ enum dma_transfer_direction direction,
+ dma_addr_t *slave_addr)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+ struct pl08x_driver_data *pl08x = plchan->host;
+ struct pl08x_txd *txd;
+ enum dma_slave_buswidth addr_width;
+ int ret, tmp;
+ u8 src_buses, dst_buses;
+ u32 maxburst, cctl;
+
+ txd = pl08x_get_txd(plchan);
+ if (!txd) {
+ dev_err(&pl08x->adev->dev, "%s no txd\n", __func__);
+ return NULL;
+ }
+
+ /*
+ * Set up addresses, the PrimeCell configured address
+ * will take precedence since this may configure the
+ * channel target address dynamically at runtime.
+ */
+ if (direction == DMA_MEM_TO_DEV) {
+ cctl = PL080_CONTROL_SRC_INCR;
+ *slave_addr = plchan->cfg.dst_addr;
+ addr_width = plchan->cfg.dst_addr_width;
+ maxburst = plchan->cfg.dst_maxburst;
+ src_buses = pl08x->mem_buses;
+ dst_buses = plchan->cd->periph_buses;
+ } else if (direction == DMA_DEV_TO_MEM) {
+ cctl = PL080_CONTROL_DST_INCR;
+ *slave_addr = plchan->cfg.src_addr;
+ addr_width = plchan->cfg.src_addr_width;
+ maxburst = plchan->cfg.src_maxburst;
+ src_buses = plchan->cd->periph_buses;
+ dst_buses = pl08x->mem_buses;
+ } else {
+ pl08x_free_txd(pl08x, txd);
+ dev_err(&pl08x->adev->dev,
+ "%s direction unsupported\n", __func__);
+ return NULL;
+ }
+
+ cctl |= pl08x_get_cctl(plchan, addr_width, maxburst);
+ if (cctl == ~0) {
+ pl08x_free_txd(pl08x, txd);
+ dev_err(&pl08x->adev->dev,
+ "DMA slave configuration botched?\n");
+ return NULL;
+ }
+
+ txd->cctl = cctl | pl08x_select_bus(false, src_buses, dst_buses);
+
+ if (plchan->cfg.device_fc)
+ tmp = (direction == DMA_MEM_TO_DEV) ? PL080_FLOW_MEM2PER_PER :
+ PL080_FLOW_PER2MEM_PER;
+ else
+ tmp = (direction == DMA_MEM_TO_DEV) ? PL080_FLOW_MEM2PER :
+ PL080_FLOW_PER2MEM;
+
+ txd->ccfg = PL080_CONFIG_ERR_IRQ_MASK |
+ PL080_CONFIG_TC_IRQ_MASK |
+ tmp << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+
+ ret = pl08x_request_mux(plchan);
+ if (ret < 0) {
+ pl08x_free_txd(pl08x, txd);
+ dev_dbg(&pl08x->adev->dev,
+ "unable to mux for transfer on %s due to platform restrictions\n",
+ plchan->name);
+ return NULL;
+ }
+
+ dev_dbg(&pl08x->adev->dev, "allocated DMA request signal %d for xfer on %s\n",
+ plchan->signal, plchan->name);
+
+ /* Assign the flow control signal to this channel */
+ if (direction == DMA_MEM_TO_DEV)
+ txd->ccfg |= plchan->signal << PL080_CONFIG_DST_SEL_SHIFT;
+ else
+ txd->ccfg |= plchan->signal << PL080_CONFIG_SRC_SEL_SHIFT;
+
+ return txd;
+}
+
+static int pl08x_tx_add_sg(struct pl08x_txd *txd,
+ enum dma_transfer_direction direction,
+ dma_addr_t slave_addr,
+ dma_addr_t buf_addr,
+ unsigned int len)
+{
+ struct pl08x_sg *dsg;
+
+ dsg = kzalloc(sizeof(struct pl08x_sg), GFP_NOWAIT);
+ if (!dsg)
+ return -ENOMEM;
+
+ list_add_tail(&dsg->node, &txd->dsg_list);
+
+ dsg->len = len;
+ if (direction == DMA_MEM_TO_DEV) {
+ dsg->src_addr = buf_addr;
+ dsg->dst_addr = slave_addr;
+ } else {
+ dsg->src_addr = slave_addr;
+ dsg->dst_addr = buf_addr;
+ }
+
+ return 0;
+}
+
+static struct dma_async_tx_descriptor *pl08x_prep_slave_sg(
+ struct dma_chan *chan, struct scatterlist *sgl,
+ unsigned int sg_len, enum dma_transfer_direction direction,
+ unsigned long flags, void *context)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+ struct pl08x_driver_data *pl08x = plchan->host;
+ struct pl08x_txd *txd;
+ struct scatterlist *sg;
+ int ret, tmp;
+ dma_addr_t slave_addr;
+
+ dev_dbg(&pl08x->adev->dev, "%s prepare transaction of %d bytes from %s\n",
+ __func__, sg_dma_len(sgl), plchan->name);
+
+ txd = pl08x_init_txd(chan, direction, &slave_addr);
+ if (!txd)
+ return NULL;
+
+ for_each_sg(sgl, sg, sg_len, tmp) {
+ ret = pl08x_tx_add_sg(txd, direction, slave_addr,
+ sg_dma_address(sg),
+ sg_dma_len(sg));
+ if (ret) {
+ pl08x_release_mux(plchan);
+ pl08x_free_txd(pl08x, txd);
+ dev_err(&pl08x->adev->dev, "%s no mem for pl080 sg\n",
+ __func__);
+ return NULL;
+ }
+ }
+
+ ret = pl08x_fill_llis_for_desc(plchan->host, txd);
+ if (!ret) {
+ pl08x_release_mux(plchan);
+ pl08x_free_txd(pl08x, txd);
+ return NULL;
+ }
+
+ return vchan_tx_prep(&plchan->vc, &txd->vd, flags);
+}
+
+static struct dma_async_tx_descriptor *pl08x_prep_dma_cyclic(
+ struct dma_chan *chan, dma_addr_t buf_addr, size_t buf_len,
+ size_t period_len, enum dma_transfer_direction direction,
+ unsigned long flags)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+ struct pl08x_driver_data *pl08x = plchan->host;
+ struct pl08x_txd *txd;
+ int ret, tmp;
+ dma_addr_t slave_addr;
+
+ dev_dbg(&pl08x->adev->dev,
+ "%s prepare cyclic transaction of %zd/%zd bytes %s %s\n",
+ __func__, period_len, buf_len,
+ direction == DMA_MEM_TO_DEV ? "to" : "from",
+ plchan->name);
+
+ txd = pl08x_init_txd(chan, direction, &slave_addr);
+ if (!txd)
+ return NULL;
+
+ txd->cyclic = true;
+ txd->cctl |= PL080_CONTROL_TC_IRQ_EN;
+ for (tmp = 0; tmp < buf_len; tmp += period_len) {
+ ret = pl08x_tx_add_sg(txd, direction, slave_addr,
+ buf_addr + tmp, period_len);
+ if (ret) {
+ pl08x_release_mux(plchan);
+ pl08x_free_txd(pl08x, txd);
+ return NULL;
+ }
+ }
+
+ ret = pl08x_fill_llis_for_desc(plchan->host, txd);
+ if (!ret) {
+ pl08x_release_mux(plchan);
+ pl08x_free_txd(pl08x, txd);
+ return NULL;
+ }
+
+ return vchan_tx_prep(&plchan->vc, &txd->vd, flags);
+}
+
+static int pl08x_config(struct dma_chan *chan,
+ struct dma_slave_config *config)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+ struct pl08x_driver_data *pl08x = plchan->host;
+
+ if (!plchan->slave)
+ return -EINVAL;
+
+ /* Reject definitely invalid configurations */
+ if (config->src_addr_width == DMA_SLAVE_BUSWIDTH_8_BYTES ||
+ config->dst_addr_width == DMA_SLAVE_BUSWIDTH_8_BYTES)
+ return -EINVAL;
+
+ if (config->device_fc && pl08x->vd->pl080s) {
+ dev_err(&pl08x->adev->dev,
+ "%s: PL080S does not support peripheral flow control\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ plchan->cfg = *config;
+
+ return 0;
+}
+
+static int pl08x_terminate_all(struct dma_chan *chan)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+ struct pl08x_driver_data *pl08x = plchan->host;
+ unsigned long flags;
+
+ spin_lock_irqsave(&plchan->vc.lock, flags);
+ if (!plchan->phychan && !plchan->at) {
+ spin_unlock_irqrestore(&plchan->vc.lock, flags);
+ return 0;
+ }
+
+ plchan->state = PL08X_CHAN_IDLE;
+
+ if (plchan->phychan) {
+ /*
+ * Mark physical channel as free and free any slave
+ * signal
+ */
+ pl08x_phy_free(plchan);
+ }
+ /* Dequeue jobs and free LLIs */
+ if (plchan->at) {
+ pl08x_desc_free(&plchan->at->vd);
+ plchan->at = NULL;
+ }
+ /* Dequeue jobs not yet fired as well */
+ pl08x_free_txd_list(pl08x, plchan);
+
+ spin_unlock_irqrestore(&plchan->vc.lock, flags);
+
+ return 0;
+}
+
+static int pl08x_pause(struct dma_chan *chan)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+ unsigned long flags;
+
+ /*
+ * Anything succeeds on channels with no physical allocation and
+ * no queued transfers.
+ */
+ spin_lock_irqsave(&plchan->vc.lock, flags);
+ if (!plchan->phychan && !plchan->at) {
+ spin_unlock_irqrestore(&plchan->vc.lock, flags);
+ return 0;
+ }
+
+ pl08x_pause_phy_chan(plchan->phychan);
+ plchan->state = PL08X_CHAN_PAUSED;
+
+ spin_unlock_irqrestore(&plchan->vc.lock, flags);
+
+ return 0;
+}
+
+static int pl08x_resume(struct dma_chan *chan)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+ unsigned long flags;
+
+ /*
+ * Anything succeeds on channels with no physical allocation and
+ * no queued transfers.
+ */
+ spin_lock_irqsave(&plchan->vc.lock, flags);
+ if (!plchan->phychan && !plchan->at) {
+ spin_unlock_irqrestore(&plchan->vc.lock, flags);
+ return 0;
+ }
+
+ pl08x_resume_phy_chan(plchan->phychan);
+ plchan->state = PL08X_CHAN_RUNNING;
+
+ spin_unlock_irqrestore(&plchan->vc.lock, flags);
+
+ return 0;
+}
+
+bool pl08x_filter_id(struct dma_chan *chan, void *chan_id)
+{
+ struct pl08x_dma_chan *plchan;
+ char *name = chan_id;
+
+ /* Reject channels for devices not bound to this driver */
+ if (chan->device->dev->driver != &pl08x_amba_driver.drv)
+ return false;
+
+ plchan = to_pl08x_chan(chan);
+
+ /* Check that the channel is not taken! */
+ if (!strcmp(plchan->name, name))
+ return true;
+
+ return false;
+}
+EXPORT_SYMBOL_GPL(pl08x_filter_id);
+
+static bool pl08x_filter_fn(struct dma_chan *chan, void *chan_id)
+{
+ struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
+
+ return plchan->cd == chan_id;
+}
+
+/*
+ * Just check that the device is there and active
+ * TODO: turn this bit on/off depending on the number of physical channels
+ * actually used, if it is zero... well shut it off. That will save some
+ * power. Cut the clock at the same time.
+ */
+static void pl08x_ensure_on(struct pl08x_driver_data *pl08x)
+{
+ /* The Nomadik variant does not have the config register */
+ if (pl08x->vd->nomadik)
+ return;
+ /* The FTDMAC020 variant does this in another register */
+ if (pl08x->vd->ftdmac020) {
+ writel(PL080_CONFIG_ENABLE, pl08x->base + FTDMAC020_CSR);
+ return;
+ }
+ writel(PL080_CONFIG_ENABLE, pl08x->base + PL080_CONFIG);
+}
+
+static irqreturn_t pl08x_irq(int irq, void *dev)
+{
+ struct pl08x_driver_data *pl08x = dev;
+ u32 mask = 0, err, tc, i;
+
+ /* check & clear - ERR & TC interrupts */
+ err = readl(pl08x->base + PL080_ERR_STATUS);
+ if (err) {
+ dev_err(&pl08x->adev->dev, "%s error interrupt, register value 0x%08x\n",
+ __func__, err);
+ writel(err, pl08x->base + PL080_ERR_CLEAR);
+ }
+ tc = readl(pl08x->base + PL080_TC_STATUS);
+ if (tc)
+ writel(tc, pl08x->base + PL080_TC_CLEAR);
+
+ if (!err && !tc)
+ return IRQ_NONE;
+
+ for (i = 0; i < pl08x->vd->channels; i++) {
+ if ((BIT(i) & err) || (BIT(i) & tc)) {
+ /* Locate physical channel */
+ struct pl08x_phy_chan *phychan = &pl08x->phy_chans[i];
+ struct pl08x_dma_chan *plchan = phychan->serving;
+ struct pl08x_txd *tx;
+
+ if (!plchan) {
+ dev_err(&pl08x->adev->dev,
+ "%s Error TC interrupt on unused channel: 0x%08x\n",
+ __func__, i);
+ continue;
+ }
+
+ spin_lock(&plchan->vc.lock);
+ tx = plchan->at;
+ if (tx && tx->cyclic) {
+ vchan_cyclic_callback(&tx->vd);
+ } else if (tx) {
+ plchan->at = NULL;
+ /*
+ * This descriptor is done, release its mux
+ * reservation.
+ */
+ pl08x_release_mux(plchan);
+ tx->done = true;
+ vchan_cookie_complete(&tx->vd);
+
+ /*
+ * And start the next descriptor (if any),
+ * otherwise free this channel.
+ */
+ if (vchan_next_desc(&plchan->vc))
+ pl08x_start_next_txd(plchan);
+ else
+ pl08x_phy_free(plchan);
+ }
+ spin_unlock(&plchan->vc.lock);
+
+ mask |= BIT(i);
+ }
+ }
+
+ return mask ? IRQ_HANDLED : IRQ_NONE;
+}
+
+static void pl08x_dma_slave_init(struct pl08x_dma_chan *chan)
+{
+ chan->slave = true;
+ chan->name = chan->cd->bus_id;
+ chan->cfg.src_addr = chan->cd->addr;
+ chan->cfg.dst_addr = chan->cd->addr;
+}
+
+/*
+ * Initialise the DMAC memcpy/slave channels.
+ * Make a local wrapper to hold required data
+ */
+static int pl08x_dma_init_virtual_channels(struct pl08x_driver_data *pl08x,
+ struct dma_device *dmadev, unsigned int channels, bool slave)
+{
+ struct pl08x_dma_chan *chan;
+ int i;
+
+ INIT_LIST_HEAD(&dmadev->channels);
+
+ /*
+ * Register as many many memcpy as we have physical channels,
+ * we won't always be able to use all but the code will have
+ * to cope with that situation.
+ */
+ for (i = 0; i < channels; i++) {
+ chan = kzalloc(sizeof(*chan), GFP_KERNEL);
+ if (!chan)
+ return -ENOMEM;
+
+ chan->host = pl08x;
+ chan->state = PL08X_CHAN_IDLE;
+ chan->signal = -1;
+
+ if (slave) {
+ chan->cd = &pl08x->pd->slave_channels[i];
+ /*
+ * Some implementations have muxed signals, whereas some
+ * use a mux in front of the signals and need dynamic
+ * assignment of signals.
+ */
+ chan->signal = i;
+ pl08x_dma_slave_init(chan);
+ } else {
+ chan->cd = kzalloc(sizeof(*chan->cd), GFP_KERNEL);
+ if (!chan->cd) {
+ kfree(chan);
+ return -ENOMEM;
+ }
+ chan->cd->bus_id = "memcpy";
+ chan->cd->periph_buses = pl08x->pd->mem_buses;
+ chan->name = kasprintf(GFP_KERNEL, "memcpy%d", i);
+ if (!chan->name) {
+ kfree(chan->cd);
+ kfree(chan);
+ return -ENOMEM;
+ }
+ }
+ dev_dbg(&pl08x->adev->dev,
+ "initialize virtual channel \"%s\"\n",
+ chan->name);
+
+ chan->vc.desc_free = pl08x_desc_free;
+ vchan_init(&chan->vc, dmadev);
+ }
+ dev_info(&pl08x->adev->dev, "initialized %d virtual %s channels\n",
+ i, slave ? "slave" : "memcpy");
+ return i;
+}
+
+static void pl08x_free_virtual_channels(struct dma_device *dmadev)
+{
+ struct pl08x_dma_chan *chan = NULL;
+ struct pl08x_dma_chan *next;
+
+ list_for_each_entry_safe(chan,
+ next, &dmadev->channels, vc.chan.device_node) {
+ list_del(&chan->vc.chan.device_node);
+ kfree(chan);
+ }
+}
+
+#ifdef CONFIG_DEBUG_FS
+static const char *pl08x_state_str(enum pl08x_dma_chan_state state)
+{
+ switch (state) {
+ case PL08X_CHAN_IDLE:
+ return "idle";
+ case PL08X_CHAN_RUNNING:
+ return "running";
+ case PL08X_CHAN_PAUSED:
+ return "paused";
+ case PL08X_CHAN_WAITING:
+ return "waiting";
+ default:
+ break;
+ }
+ return "UNKNOWN STATE";
+}
+
+static int pl08x_debugfs_show(struct seq_file *s, void *data)
+{
+ struct pl08x_driver_data *pl08x = s->private;
+ struct pl08x_dma_chan *chan;
+ struct pl08x_phy_chan *ch;
+ unsigned long flags;
+ int i;
+
+ seq_printf(s, "PL08x physical channels:\n");
+ seq_printf(s, "CHANNEL:\tUSER:\n");
+ seq_printf(s, "--------\t-----\n");
+ for (i = 0; i < pl08x->vd->channels; i++) {
+ struct pl08x_dma_chan *virt_chan;
+
+ ch = &pl08x->phy_chans[i];
+
+ spin_lock_irqsave(&ch->lock, flags);
+ virt_chan = ch->serving;
+
+ seq_printf(s, "%d\t\t%s%s\n",
+ ch->id,
+ virt_chan ? virt_chan->name : "(none)",
+ ch->locked ? " LOCKED" : "");
+
+ spin_unlock_irqrestore(&ch->lock, flags);
+ }
+
+ seq_printf(s, "\nPL08x virtual memcpy channels:\n");
+ seq_printf(s, "CHANNEL:\tSTATE:\n");
+ seq_printf(s, "--------\t------\n");
+ list_for_each_entry(chan, &pl08x->memcpy.channels, vc.chan.device_node) {
+ seq_printf(s, "%s\t\t%s\n", chan->name,
+ pl08x_state_str(chan->state));
+ }
+
+ if (pl08x->has_slave) {
+ seq_printf(s, "\nPL08x virtual slave channels:\n");
+ seq_printf(s, "CHANNEL:\tSTATE:\n");
+ seq_printf(s, "--------\t------\n");
+ list_for_each_entry(chan, &pl08x->slave.channels,
+ vc.chan.device_node) {
+ seq_printf(s, "%s\t\t%s\n", chan->name,
+ pl08x_state_str(chan->state));
+ }
+ }
+
+ return 0;
+}
+
+static int pl08x_debugfs_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, pl08x_debugfs_show, inode->i_private);
+}
+
+static const struct file_operations pl08x_debugfs_operations = {
+ .open = pl08x_debugfs_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static void init_pl08x_debugfs(struct pl08x_driver_data *pl08x)
+{
+ /* Expose a simple debugfs interface to view all clocks */
+ (void) debugfs_create_file(dev_name(&pl08x->adev->dev),
+ S_IFREG | S_IRUGO, NULL, pl08x,
+ &pl08x_debugfs_operations);
+}
+
+#else
+static inline void init_pl08x_debugfs(struct pl08x_driver_data *pl08x)
+{
+}
+#endif
+
+#ifdef CONFIG_OF
+static struct dma_chan *pl08x_find_chan_id(struct pl08x_driver_data *pl08x,
+ u32 id)
+{
+ struct pl08x_dma_chan *chan;
+
+ /* Trying to get a slave channel from something with no slave support */
+ if (!pl08x->has_slave)
+ return NULL;
+
+ list_for_each_entry(chan, &pl08x->slave.channels, vc.chan.device_node) {
+ if (chan->signal == id)
+ return &chan->vc.chan;
+ }
+
+ return NULL;
+}
+
+static struct dma_chan *pl08x_of_xlate(struct of_phandle_args *dma_spec,
+ struct of_dma *ofdma)
+{
+ struct pl08x_driver_data *pl08x = ofdma->of_dma_data;
+ struct dma_chan *dma_chan;
+ struct pl08x_dma_chan *plchan;
+
+ if (!pl08x)
+ return NULL;
+
+ if (dma_spec->args_count != 2) {
+ dev_err(&pl08x->adev->dev,
+ "DMA channel translation requires two cells\n");
+ return NULL;
+ }
+
+ dma_chan = pl08x_find_chan_id(pl08x, dma_spec->args[0]);
+ if (!dma_chan) {
+ dev_err(&pl08x->adev->dev,
+ "DMA slave channel not found\n");
+ return NULL;
+ }
+
+ plchan = to_pl08x_chan(dma_chan);
+ dev_dbg(&pl08x->adev->dev,
+ "translated channel for signal %d\n",
+ dma_spec->args[0]);
+
+ /* Augment channel data for applicable AHB buses */
+ plchan->cd->periph_buses = dma_spec->args[1];
+ return dma_get_slave_channel(dma_chan);
+}
+
+static int pl08x_of_probe(struct amba_device *adev,
+ struct pl08x_driver_data *pl08x,
+ struct device_node *np)
+{
+ struct pl08x_platform_data *pd;
+ struct pl08x_channel_data *chanp = NULL;
+ u32 val;
+ int ret;
+ int i;
+
+ pd = devm_kzalloc(&adev->dev, sizeof(*pd), GFP_KERNEL);
+ if (!pd)
+ return -ENOMEM;
+
+ /* Eligible bus masters for fetching LLIs */
+ if (of_property_read_bool(np, "lli-bus-interface-ahb1"))
+ pd->lli_buses |= PL08X_AHB1;
+ if (of_property_read_bool(np, "lli-bus-interface-ahb2"))
+ pd->lli_buses |= PL08X_AHB2;
+ if (!pd->lli_buses) {
+ dev_info(&adev->dev, "no bus masters for LLIs stated, assume all\n");
+ pd->lli_buses |= PL08X_AHB1 | PL08X_AHB2;
+ }
+
+ /* Eligible bus masters for memory access */
+ if (of_property_read_bool(np, "mem-bus-interface-ahb1"))
+ pd->mem_buses |= PL08X_AHB1;
+ if (of_property_read_bool(np, "mem-bus-interface-ahb2"))
+ pd->mem_buses |= PL08X_AHB2;
+ if (!pd->mem_buses) {
+ dev_info(&adev->dev, "no bus masters for memory stated, assume all\n");
+ pd->mem_buses |= PL08X_AHB1 | PL08X_AHB2;
+ }
+
+ /* Parse the memcpy channel properties */
+ ret = of_property_read_u32(np, "memcpy-burst-size", &val);
+ if (ret) {
+ dev_info(&adev->dev, "no memcpy burst size specified, using 1 byte\n");
+ val = 1;
+ }
+ switch (val) {
+ default:
+ dev_err(&adev->dev, "illegal burst size for memcpy, set to 1\n");
+ /* Fall through */
+ case 1:
+ pd->memcpy_burst_size = PL08X_BURST_SZ_1;
+ break;
+ case 4:
+ pd->memcpy_burst_size = PL08X_BURST_SZ_4;
+ break;
+ case 8:
+ pd->memcpy_burst_size = PL08X_BURST_SZ_8;
+ break;
+ case 16:
+ pd->memcpy_burst_size = PL08X_BURST_SZ_16;
+ break;
+ case 32:
+ pd->memcpy_burst_size = PL08X_BURST_SZ_32;
+ break;
+ case 64:
+ pd->memcpy_burst_size = PL08X_BURST_SZ_64;
+ break;
+ case 128:
+ pd->memcpy_burst_size = PL08X_BURST_SZ_128;
+ break;
+ case 256:
+ pd->memcpy_burst_size = PL08X_BURST_SZ_256;
+ break;
+ }
+
+ ret = of_property_read_u32(np, "memcpy-bus-width", &val);
+ if (ret) {
+ dev_info(&adev->dev, "no memcpy bus width specified, using 8 bits\n");
+ val = 8;
+ }
+ switch (val) {
+ default:
+ dev_err(&adev->dev, "illegal bus width for memcpy, set to 8 bits\n");
+ /* Fall through */
+ case 8:
+ pd->memcpy_bus_width = PL08X_BUS_WIDTH_8_BITS;
+ break;
+ case 16:
+ pd->memcpy_bus_width = PL08X_BUS_WIDTH_16_BITS;
+ break;
+ case 32:
+ pd->memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS;
+ break;
+ }
+
+ /*
+ * Allocate channel data for all possible slave channels (one
+ * for each possible signal), channels will then be allocated
+ * for a device and have it's AHB interfaces set up at
+ * translation time.
+ */
+ if (pl08x->vd->signals) {
+ chanp = devm_kcalloc(&adev->dev,
+ pl08x->vd->signals,
+ sizeof(struct pl08x_channel_data),
+ GFP_KERNEL);
+ if (!chanp)
+ return -ENOMEM;
+
+ pd->slave_channels = chanp;
+ for (i = 0; i < pl08x->vd->signals; i++) {
+ /*
+ * chanp->periph_buses will be assigned at translation
+ */
+ chanp->bus_id = kasprintf(GFP_KERNEL, "slave%d", i);
+ chanp++;
+ }
+ pd->num_slave_channels = pl08x->vd->signals;
+ }
+
+ pl08x->pd = pd;
+
+ return of_dma_controller_register(adev->dev.of_node, pl08x_of_xlate,
+ pl08x);
+}
+#else
+static inline int pl08x_of_probe(struct amba_device *adev,
+ struct pl08x_driver_data *pl08x,
+ struct device_node *np)
+{
+ return -EINVAL;
+}
+#endif
+
+static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
+{
+ struct pl08x_driver_data *pl08x;
+ struct vendor_data *vd = id->data;
+ struct device_node *np = adev->dev.of_node;
+ u32 tsfr_size;
+ int ret = 0;
+ int i;
+
+ ret = amba_request_regions(adev, NULL);
+ if (ret)
+ return ret;
+
+ /* Ensure that we can do DMA */
+ ret = dma_set_mask_and_coherent(&adev->dev, DMA_BIT_MASK(32));
+ if (ret)
+ goto out_no_pl08x;
+
+ /* Create the driver state holder */
+ pl08x = kzalloc(sizeof(*pl08x), GFP_KERNEL);
+ if (!pl08x) {
+ ret = -ENOMEM;
+ goto out_no_pl08x;
+ }
+
+ /* Assign useful pointers to the driver state */
+ pl08x->adev = adev;
+ pl08x->vd = vd;
+
+ pl08x->base = ioremap(adev->res.start, resource_size(&adev->res));
+ if (!pl08x->base) {
+ ret = -ENOMEM;
+ goto out_no_ioremap;
+ }
+
+ if (vd->ftdmac020) {
+ u32 val;
+
+ val = readl(pl08x->base + FTDMAC020_REVISION);
+ dev_info(&pl08x->adev->dev, "FTDMAC020 %d.%d rel %d\n",
+ (val >> 16) & 0xff, (val >> 8) & 0xff, val & 0xff);
+ val = readl(pl08x->base + FTDMAC020_FEATURE);
+ dev_info(&pl08x->adev->dev, "FTDMAC020 %d channels, "
+ "%s built-in bridge, %s, %s linked lists\n",
+ (val >> 12) & 0x0f,
+ (val & BIT(10)) ? "no" : "has",
+ (val & BIT(9)) ? "AHB0 and AHB1" : "AHB0",
+ (val & BIT(8)) ? "supports" : "does not support");
+
+ /* Vendor data from feature register */
+ if (!(val & BIT(8)))
+ dev_warn(&pl08x->adev->dev,
+ "linked lists not supported, required\n");
+ vd->channels = (val >> 12) & 0x0f;
+ vd->dualmaster = !!(val & BIT(9));
+ }
+
+ /* Initialize memcpy engine */
+ dma_cap_set(DMA_MEMCPY, pl08x->memcpy.cap_mask);
+ pl08x->memcpy.dev = &adev->dev;
+ pl08x->memcpy.device_free_chan_resources = pl08x_free_chan_resources;
+ pl08x->memcpy.device_prep_dma_memcpy = pl08x_prep_dma_memcpy;
+ pl08x->memcpy.device_prep_dma_interrupt = pl08x_prep_dma_interrupt;
+ pl08x->memcpy.device_tx_status = pl08x_dma_tx_status;
+ pl08x->memcpy.device_issue_pending = pl08x_issue_pending;
+ pl08x->memcpy.device_config = pl08x_config;
+ pl08x->memcpy.device_pause = pl08x_pause;
+ pl08x->memcpy.device_resume = pl08x_resume;
+ pl08x->memcpy.device_terminate_all = pl08x_terminate_all;
+ pl08x->memcpy.src_addr_widths = PL80X_DMA_BUSWIDTHS;
+ pl08x->memcpy.dst_addr_widths = PL80X_DMA_BUSWIDTHS;
+ pl08x->memcpy.directions = BIT(DMA_MEM_TO_MEM);
+ pl08x->memcpy.residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT;
+ if (vd->ftdmac020)
+ pl08x->memcpy.copy_align = DMAENGINE_ALIGN_4_BYTES;
+
+
+ /*
+ * Initialize slave engine, if the block has no signals, that means
+ * we have no slave support.
+ */
+ if (vd->signals) {
+ pl08x->has_slave = true;
+ dma_cap_set(DMA_SLAVE, pl08x->slave.cap_mask);
+ dma_cap_set(DMA_CYCLIC, pl08x->slave.cap_mask);
+ pl08x->slave.dev = &adev->dev;
+ pl08x->slave.device_free_chan_resources =
+ pl08x_free_chan_resources;
+ pl08x->slave.device_prep_dma_interrupt =
+ pl08x_prep_dma_interrupt;
+ pl08x->slave.device_tx_status = pl08x_dma_tx_status;
+ pl08x->slave.device_issue_pending = pl08x_issue_pending;
+ pl08x->slave.device_prep_slave_sg = pl08x_prep_slave_sg;
+ pl08x->slave.device_prep_dma_cyclic = pl08x_prep_dma_cyclic;
+ pl08x->slave.device_config = pl08x_config;
+ pl08x->slave.device_pause = pl08x_pause;
+ pl08x->slave.device_resume = pl08x_resume;
+ pl08x->slave.device_terminate_all = pl08x_terminate_all;
+ pl08x->slave.src_addr_widths = PL80X_DMA_BUSWIDTHS;
+ pl08x->slave.dst_addr_widths = PL80X_DMA_BUSWIDTHS;
+ pl08x->slave.directions =
+ BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
+ pl08x->slave.residue_granularity =
+ DMA_RESIDUE_GRANULARITY_SEGMENT;
+ }
+
+ /* Get the platform data */
+ pl08x->pd = dev_get_platdata(&adev->dev);
+ if (!pl08x->pd) {
+ if (np) {
+ ret = pl08x_of_probe(adev, pl08x, np);
+ if (ret)
+ goto out_no_platdata;
+ } else {
+ dev_err(&adev->dev, "no platform data supplied\n");
+ ret = -EINVAL;
+ goto out_no_platdata;
+ }
+ } else {
+ pl08x->slave.filter.map = pl08x->pd->slave_map;
+ pl08x->slave.filter.mapcnt = pl08x->pd->slave_map_len;
+ pl08x->slave.filter.fn = pl08x_filter_fn;
+ }
+
+ /* By default, AHB1 only. If dualmaster, from platform */
+ pl08x->lli_buses = PL08X_AHB1;
+ pl08x->mem_buses = PL08X_AHB1;
+ if (pl08x->vd->dualmaster) {
+ pl08x->lli_buses = pl08x->pd->lli_buses;
+ pl08x->mem_buses = pl08x->pd->mem_buses;
+ }
+
+ if (vd->pl080s)
+ pl08x->lli_words = PL080S_LLI_WORDS;
+ else
+ pl08x->lli_words = PL080_LLI_WORDS;
+ tsfr_size = MAX_NUM_TSFR_LLIS * pl08x->lli_words * sizeof(u32);
+
+ /* A DMA memory pool for LLIs, align on 1-byte boundary */
+ pl08x->pool = dma_pool_create(DRIVER_NAME, &pl08x->adev->dev,
+ tsfr_size, PL08X_ALIGN, 0);
+ if (!pl08x->pool) {
+ ret = -ENOMEM;
+ goto out_no_lli_pool;
+ }
+
+ /* Turn on the PL08x */
+ pl08x_ensure_on(pl08x);
+
+ /* Clear any pending interrupts */
+ if (vd->ftdmac020)
+ /* This variant has error IRQs in bits 16-19 */
+ writel(0x0000FFFF, pl08x->base + PL080_ERR_CLEAR);
+ else
+ writel(0x000000FF, pl08x->base + PL080_ERR_CLEAR);
+ writel(0x000000FF, pl08x->base + PL080_TC_CLEAR);
+
+ /* Attach the interrupt handler */
+ ret = request_irq(adev->irq[0], pl08x_irq, 0, DRIVER_NAME, pl08x);
+ if (ret) {
+ dev_err(&adev->dev, "%s failed to request interrupt %d\n",
+ __func__, adev->irq[0]);
+ goto out_no_irq;
+ }
+
+ /* Initialize physical channels */
+ pl08x->phy_chans = kzalloc((vd->channels * sizeof(*pl08x->phy_chans)),
+ GFP_KERNEL);
+ if (!pl08x->phy_chans) {
+ ret = -ENOMEM;
+ goto out_no_phychans;
+ }
+
+ for (i = 0; i < vd->channels; i++) {
+ struct pl08x_phy_chan *ch = &pl08x->phy_chans[i];
+
+ ch->id = i;
+ ch->base = pl08x->base + PL080_Cx_BASE(i);
+ if (vd->ftdmac020) {
+ /* FTDMA020 has a special channel busy register */
+ ch->reg_busy = ch->base + FTDMAC020_CH_BUSY;
+ ch->reg_config = ch->base + FTDMAC020_CH_CFG;
+ ch->reg_control = ch->base + FTDMAC020_CH_CSR;
+ ch->reg_src = ch->base + FTDMAC020_CH_SRC_ADDR;
+ ch->reg_dst = ch->base + FTDMAC020_CH_DST_ADDR;
+ ch->reg_lli = ch->base + FTDMAC020_CH_LLP;
+ ch->ftdmac020 = true;
+ } else {
+ ch->reg_config = ch->base + vd->config_offset;
+ ch->reg_control = ch->base + PL080_CH_CONTROL;
+ ch->reg_src = ch->base + PL080_CH_SRC_ADDR;
+ ch->reg_dst = ch->base + PL080_CH_DST_ADDR;
+ ch->reg_lli = ch->base + PL080_CH_LLI;
+ }
+ if (vd->pl080s)
+ ch->pl080s = true;
+
+ spin_lock_init(&ch->lock);
+
+ /*
+ * Nomadik variants can have channels that are locked
+ * down for the secure world only. Lock up these channels
+ * by perpetually serving a dummy virtual channel.
+ */
+ if (vd->nomadik) {
+ u32 val;
+
+ val = readl(ch->reg_config);
+ if (val & (PL080N_CONFIG_ITPROT | PL080N_CONFIG_SECPROT)) {
+ dev_info(&adev->dev, "physical channel %d reserved for secure access only\n", i);
+ ch->locked = true;
+ }
+ }
+
+ dev_dbg(&adev->dev, "physical channel %d is %s\n",
+ i, pl08x_phy_channel_busy(ch) ? "BUSY" : "FREE");
+ }
+
+ /* Register as many memcpy channels as there are physical channels */
+ ret = pl08x_dma_init_virtual_channels(pl08x, &pl08x->memcpy,
+ pl08x->vd->channels, false);
+ if (ret <= 0) {
+ dev_warn(&pl08x->adev->dev,
+ "%s failed to enumerate memcpy channels - %d\n",
+ __func__, ret);
+ goto out_no_memcpy;
+ }
+
+ /* Register slave channels */
+ if (pl08x->has_slave) {
+ ret = pl08x_dma_init_virtual_channels(pl08x, &pl08x->slave,
+ pl08x->pd->num_slave_channels, true);
+ if (ret < 0) {
+ dev_warn(&pl08x->adev->dev,
+ "%s failed to enumerate slave channels - %d\n",
+ __func__, ret);
+ goto out_no_slave;
+ }
+ }
+
+ ret = dma_async_device_register(&pl08x->memcpy);
+ if (ret) {
+ dev_warn(&pl08x->adev->dev,
+ "%s failed to register memcpy as an async device - %d\n",
+ __func__, ret);
+ goto out_no_memcpy_reg;
+ }
+
+ if (pl08x->has_slave) {
+ ret = dma_async_device_register(&pl08x->slave);
+ if (ret) {
+ dev_warn(&pl08x->adev->dev,
+ "%s failed to register slave as an async device - %d\n",
+ __func__, ret);
+ goto out_no_slave_reg;
+ }
+ }
+
+ amba_set_drvdata(adev, pl08x);
+ init_pl08x_debugfs(pl08x);
+ dev_info(&pl08x->adev->dev, "DMA: PL%03x%s rev%u at 0x%08llx irq %d\n",
+ amba_part(adev), pl08x->vd->pl080s ? "s" : "", amba_rev(adev),
+ (unsigned long long)adev->res.start, adev->irq[0]);
+
+ return 0;
+
+out_no_slave_reg:
+ dma_async_device_unregister(&pl08x->memcpy);
+out_no_memcpy_reg:
+ if (pl08x->has_slave)
+ pl08x_free_virtual_channels(&pl08x->slave);
+out_no_slave:
+ pl08x_free_virtual_channels(&pl08x->memcpy);
+out_no_memcpy:
+ kfree(pl08x->phy_chans);
+out_no_phychans:
+ free_irq(adev->irq[0], pl08x);
+out_no_irq:
+ dma_pool_destroy(pl08x->pool);
+out_no_lli_pool:
+out_no_platdata:
+ iounmap(pl08x->base);
+out_no_ioremap:
+ kfree(pl08x);
+out_no_pl08x:
+ amba_release_regions(adev);
+ return ret;
+}
+
+/* PL080 has 8 channels and the PL080 have just 2 */
+static struct vendor_data vendor_pl080 = {
+ .config_offset = PL080_CH_CONFIG,
+ .channels = 8,
+ .signals = 16,
+ .dualmaster = true,
+ .max_transfer_size = PL080_CONTROL_TRANSFER_SIZE_MASK,
+};
+
+static struct vendor_data vendor_nomadik = {
+ .config_offset = PL080_CH_CONFIG,
+ .channels = 8,
+ .signals = 32,
+ .dualmaster = true,
+ .nomadik = true,
+ .max_transfer_size = PL080_CONTROL_TRANSFER_SIZE_MASK,
+};
+
+static struct vendor_data vendor_pl080s = {
+ .config_offset = PL080S_CH_CONFIG,
+ .channels = 8,
+ .signals = 32,
+ .pl080s = true,
+ .max_transfer_size = PL080S_CONTROL_TRANSFER_SIZE_MASK,
+};
+
+static struct vendor_data vendor_pl081 = {
+ .config_offset = PL080_CH_CONFIG,
+ .channels = 2,
+ .signals = 16,
+ .dualmaster = false,
+ .max_transfer_size = PL080_CONTROL_TRANSFER_SIZE_MASK,
+};
+
+static struct vendor_data vendor_ftdmac020 = {
+ .config_offset = PL080_CH_CONFIG,
+ .ftdmac020 = true,
+ .max_transfer_size = PL080_CONTROL_TRANSFER_SIZE_MASK,
+};
+
+static const struct amba_id pl08x_ids[] = {
+ /* Samsung PL080S variant */
+ {
+ .id = 0x0a141080,
+ .mask = 0xffffffff,
+ .data = &vendor_pl080s,
+ },
+ /* PL080 */
+ {
+ .id = 0x00041080,
+ .mask = 0x000fffff,
+ .data = &vendor_pl080,
+ },
+ /* PL081 */
+ {
+ .id = 0x00041081,
+ .mask = 0x000fffff,
+ .data = &vendor_pl081,
+ },
+ /* Nomadik 8815 PL080 variant */
+ {
+ .id = 0x00280080,
+ .mask = 0x00ffffff,
+ .data = &vendor_nomadik,
+ },
+ /* Faraday Technology FTDMAC020 */
+ {
+ .id = 0x0003b080,
+ .mask = 0x000fffff,
+ .data = &vendor_ftdmac020,
+ },
+ { 0, 0 },
+};
+
+MODULE_DEVICE_TABLE(amba, pl08x_ids);
+
+static struct amba_driver pl08x_amba_driver = {
+ .drv.name = DRIVER_NAME,
+ .id_table = pl08x_ids,
+ .probe = pl08x_probe,
+};
+
+static int __init pl08x_init(void)
+{
+ int retval;
+ retval = amba_driver_register(&pl08x_amba_driver);
+ if (retval)
+ printk(KERN_WARNING DRIVER_NAME
+ "failed to register as an AMBA device (%d)\n",
+ retval);
+ return retval;
+}
+subsys_initcall(pl08x_init);