[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/drivers/mtd/nand/denali.c b/src/kernel/linux/v4.14/drivers/mtd/nand/denali.c
new file mode 100644
index 0000000..390a18a
--- /dev/null
+++ b/src/kernel/linux/v4.14/drivers/mtd/nand/denali.c
@@ -0,0 +1,1451 @@
+/*
+ * NAND Flash Controller Device Driver
+ * Copyright © 2009-2010, Intel Corporation and its suppliers.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ */
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/wait.h>
+#include <linux/mutex.h>
+#include <linux/mtd/mtd.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+#include "denali.h"
+
+MODULE_LICENSE("GPL");
+
+#define DENALI_NAND_NAME "denali-nand"
+
+/* Host Data/Command Interface */
+#define DENALI_HOST_ADDR 0x00
+#define DENALI_HOST_DATA 0x10
+
+#define DENALI_MAP00 (0 << 26) /* direct access to buffer */
+#define DENALI_MAP01 (1 << 26) /* read/write pages in PIO */
+#define DENALI_MAP10 (2 << 26) /* high-level control plane */
+#define DENALI_MAP11 (3 << 26) /* direct controller access */
+
+/* MAP11 access cycle type */
+#define DENALI_MAP11_CMD ((DENALI_MAP11) | 0) /* command cycle */
+#define DENALI_MAP11_ADDR ((DENALI_MAP11) | 1) /* address cycle */
+#define DENALI_MAP11_DATA ((DENALI_MAP11) | 2) /* data cycle */
+
+/* MAP10 commands */
+#define DENALI_ERASE 0x01
+
+#define DENALI_BANK(denali) ((denali)->active_bank << 24)
+
+#define DENALI_INVALID_BANK -1
+#define DENALI_NR_BANKS 4
+
+/*
+ * The bus interface clock, clk_x, is phase aligned with the core clock. The
+ * clk_x is an integral multiple N of the core clk. The value N is configured
+ * at IP delivery time, and its available value is 4, 5, or 6. We need to align
+ * to the largest value to make it work with any possible configuration.
+ */
+#define DENALI_CLK_X_MULT 6
+
+/*
+ * this macro allows us to convert from an MTD structure to our own
+ * device context (denali) structure.
+ */
+static inline struct denali_nand_info *mtd_to_denali(struct mtd_info *mtd)
+{
+ return container_of(mtd_to_nand(mtd), struct denali_nand_info, nand);
+}
+
+static void denali_host_write(struct denali_nand_info *denali,
+ uint32_t addr, uint32_t data)
+{
+ iowrite32(addr, denali->host + DENALI_HOST_ADDR);
+ iowrite32(data, denali->host + DENALI_HOST_DATA);
+}
+
+/*
+ * Use the configuration feature register to determine the maximum number of
+ * banks that the hardware supports.
+ */
+static void detect_max_banks(struct denali_nand_info *denali)
+{
+ uint32_t features = ioread32(denali->reg + FEATURES);
+
+ denali->max_banks = 1 << (features & FEATURES__N_BANKS);
+
+ /* the encoding changed from rev 5.0 to 5.1 */
+ if (denali->revision < 0x0501)
+ denali->max_banks <<= 1;
+}
+
+static void denali_enable_irq(struct denali_nand_info *denali)
+{
+ int i;
+
+ for (i = 0; i < DENALI_NR_BANKS; i++)
+ iowrite32(U32_MAX, denali->reg + INTR_EN(i));
+ iowrite32(GLOBAL_INT_EN_FLAG, denali->reg + GLOBAL_INT_ENABLE);
+}
+
+static void denali_disable_irq(struct denali_nand_info *denali)
+{
+ int i;
+
+ for (i = 0; i < DENALI_NR_BANKS; i++)
+ iowrite32(0, denali->reg + INTR_EN(i));
+ iowrite32(0, denali->reg + GLOBAL_INT_ENABLE);
+}
+
+static void denali_clear_irq(struct denali_nand_info *denali,
+ int bank, uint32_t irq_status)
+{
+ /* write one to clear bits */
+ iowrite32(irq_status, denali->reg + INTR_STATUS(bank));
+}
+
+static void denali_clear_irq_all(struct denali_nand_info *denali)
+{
+ int i;
+
+ for (i = 0; i < DENALI_NR_BANKS; i++)
+ denali_clear_irq(denali, i, U32_MAX);
+}
+
+static irqreturn_t denali_isr(int irq, void *dev_id)
+{
+ struct denali_nand_info *denali = dev_id;
+ irqreturn_t ret = IRQ_NONE;
+ uint32_t irq_status;
+ int i;
+
+ spin_lock(&denali->irq_lock);
+
+ for (i = 0; i < DENALI_NR_BANKS; i++) {
+ irq_status = ioread32(denali->reg + INTR_STATUS(i));
+ if (irq_status)
+ ret = IRQ_HANDLED;
+
+ denali_clear_irq(denali, i, irq_status);
+
+ if (i != denali->active_bank)
+ continue;
+
+ denali->irq_status |= irq_status;
+
+ if (denali->irq_status & denali->irq_mask)
+ complete(&denali->complete);
+ }
+
+ spin_unlock(&denali->irq_lock);
+
+ return ret;
+}
+
+static void denali_reset_irq(struct denali_nand_info *denali)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&denali->irq_lock, flags);
+ denali->irq_status = 0;
+ denali->irq_mask = 0;
+ spin_unlock_irqrestore(&denali->irq_lock, flags);
+}
+
+static uint32_t denali_wait_for_irq(struct denali_nand_info *denali,
+ uint32_t irq_mask)
+{
+ unsigned long time_left, flags;
+ uint32_t irq_status;
+
+ spin_lock_irqsave(&denali->irq_lock, flags);
+
+ irq_status = denali->irq_status;
+
+ if (irq_mask & irq_status) {
+ /* return immediately if the IRQ has already happened. */
+ spin_unlock_irqrestore(&denali->irq_lock, flags);
+ return irq_status;
+ }
+
+ denali->irq_mask = irq_mask;
+ reinit_completion(&denali->complete);
+ spin_unlock_irqrestore(&denali->irq_lock, flags);
+
+ time_left = wait_for_completion_timeout(&denali->complete,
+ msecs_to_jiffies(1000));
+ if (!time_left) {
+ dev_err(denali->dev, "timeout while waiting for irq 0x%x\n",
+ denali->irq_mask);
+ return 0;
+ }
+
+ return denali->irq_status;
+}
+
+static uint32_t denali_check_irq(struct denali_nand_info *denali)
+{
+ unsigned long flags;
+ uint32_t irq_status;
+
+ spin_lock_irqsave(&denali->irq_lock, flags);
+ irq_status = denali->irq_status;
+ spin_unlock_irqrestore(&denali->irq_lock, flags);
+
+ return irq_status;
+}
+
+/*
+ * This helper function setups the registers for ECC and whether or not
+ * the spare area will be transferred.
+ */
+static void setup_ecc_for_xfer(struct denali_nand_info *denali, bool ecc_en,
+ bool transfer_spare)
+{
+ int ecc_en_flag, transfer_spare_flag;
+
+ /* set ECC, transfer spare bits if needed */
+ ecc_en_flag = ecc_en ? ECC_ENABLE__FLAG : 0;
+ transfer_spare_flag = transfer_spare ? TRANSFER_SPARE_REG__FLAG : 0;
+
+ /* Enable spare area/ECC per user's request. */
+ iowrite32(ecc_en_flag, denali->reg + ECC_ENABLE);
+ iowrite32(transfer_spare_flag, denali->reg + TRANSFER_SPARE_REG);
+}
+
+static void denali_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ int i;
+
+ iowrite32(DENALI_MAP11_DATA | DENALI_BANK(denali),
+ denali->host + DENALI_HOST_ADDR);
+
+ for (i = 0; i < len; i++)
+ buf[i] = ioread32(denali->host + DENALI_HOST_DATA);
+}
+
+static void denali_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ int i;
+
+ iowrite32(DENALI_MAP11_DATA | DENALI_BANK(denali),
+ denali->host + DENALI_HOST_ADDR);
+
+ for (i = 0; i < len; i++)
+ iowrite32(buf[i], denali->host + DENALI_HOST_DATA);
+}
+
+static void denali_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint16_t *buf16 = (uint16_t *)buf;
+ int i;
+
+ iowrite32(DENALI_MAP11_DATA | DENALI_BANK(denali),
+ denali->host + DENALI_HOST_ADDR);
+
+ for (i = 0; i < len / 2; i++)
+ buf16[i] = ioread32(denali->host + DENALI_HOST_DATA);
+}
+
+static void denali_write_buf16(struct mtd_info *mtd, const uint8_t *buf,
+ int len)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ const uint16_t *buf16 = (const uint16_t *)buf;
+ int i;
+
+ iowrite32(DENALI_MAP11_DATA | DENALI_BANK(denali),
+ denali->host + DENALI_HOST_ADDR);
+
+ for (i = 0; i < len / 2; i++)
+ iowrite32(buf16[i], denali->host + DENALI_HOST_DATA);
+}
+
+static uint8_t denali_read_byte(struct mtd_info *mtd)
+{
+ uint8_t byte;
+
+ denali_read_buf(mtd, &byte, 1);
+
+ return byte;
+}
+
+static void denali_write_byte(struct mtd_info *mtd, uint8_t byte)
+{
+ denali_write_buf(mtd, &byte, 1);
+}
+
+static uint16_t denali_read_word(struct mtd_info *mtd)
+{
+ uint16_t word;
+
+ denali_read_buf16(mtd, (uint8_t *)&word, 2);
+
+ return word;
+}
+
+static void denali_cmd_ctrl(struct mtd_info *mtd, int dat, unsigned int ctrl)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t type;
+
+ if (ctrl & NAND_CLE)
+ type = DENALI_MAP11_CMD;
+ else if (ctrl & NAND_ALE)
+ type = DENALI_MAP11_ADDR;
+ else
+ return;
+
+ /*
+ * Some commands are followed by chip->dev_ready or chip->waitfunc.
+ * irq_status must be cleared here to catch the R/B# interrupt later.
+ */
+ if (ctrl & NAND_CTRL_CHANGE)
+ denali_reset_irq(denali);
+
+ denali_host_write(denali, DENALI_BANK(denali) | type, dat);
+}
+
+static int denali_dev_ready(struct mtd_info *mtd)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+
+ return !!(denali_check_irq(denali) & INTR__INT_ACT);
+}
+
+static int denali_check_erased_page(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf,
+ unsigned long uncor_ecc_flags,
+ unsigned int max_bitflips)
+{
+ uint8_t *ecc_code = chip->buffers->ecccode;
+ int ecc_steps = chip->ecc.steps;
+ int ecc_size = chip->ecc.size;
+ int ecc_bytes = chip->ecc.bytes;
+ int i, ret, stat;
+
+ ret = mtd_ooblayout_get_eccbytes(mtd, ecc_code, chip->oob_poi, 0,
+ chip->ecc.total);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < ecc_steps; i++) {
+ if (!(uncor_ecc_flags & BIT(i)))
+ continue;
+
+ stat = nand_check_erased_ecc_chunk(buf, ecc_size,
+ ecc_code, ecc_bytes,
+ NULL, 0,
+ chip->ecc.strength);
+ if (stat < 0) {
+ mtd->ecc_stats.failed++;
+ } else {
+ mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
+
+ buf += ecc_size;
+ ecc_code += ecc_bytes;
+ }
+
+ return max_bitflips;
+}
+
+static int denali_hw_ecc_fixup(struct mtd_info *mtd,
+ struct denali_nand_info *denali,
+ unsigned long *uncor_ecc_flags)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ int bank = denali->active_bank;
+ uint32_t ecc_cor;
+ unsigned int max_bitflips;
+
+ ecc_cor = ioread32(denali->reg + ECC_COR_INFO(bank));
+ ecc_cor >>= ECC_COR_INFO__SHIFT(bank);
+
+ if (ecc_cor & ECC_COR_INFO__UNCOR_ERR) {
+ /*
+ * This flag is set when uncorrectable error occurs at least in
+ * one ECC sector. We can not know "how many sectors", or
+ * "which sector(s)". We need erase-page check for all sectors.
+ */
+ *uncor_ecc_flags = GENMASK(chip->ecc.steps - 1, 0);
+ return 0;
+ }
+
+ max_bitflips = ecc_cor & ECC_COR_INFO__MAX_ERRORS;
+
+ /*
+ * The register holds the maximum of per-sector corrected bitflips.
+ * This is suitable for the return value of the ->read_page() callback.
+ * Unfortunately, we can not know the total number of corrected bits in
+ * the page. Increase the stats by max_bitflips. (compromised solution)
+ */
+ mtd->ecc_stats.corrected += max_bitflips;
+
+ return max_bitflips;
+}
+
+#define ECC_SECTOR(x) (((x) & ECC_ERROR_ADDRESS__SECTOR_NR) >> 12)
+#define ECC_BYTE(x) (((x) & ECC_ERROR_ADDRESS__OFFSET))
+#define ECC_CORRECTION_VALUE(x) ((x) & ERR_CORRECTION_INFO__BYTEMASK)
+#define ECC_ERROR_UNCORRECTABLE(x) ((x) & ERR_CORRECTION_INFO__ERROR_TYPE)
+#define ECC_ERR_DEVICE(x) (((x) & ERR_CORRECTION_INFO__DEVICE_NR) >> 8)
+#define ECC_LAST_ERR(x) ((x) & ERR_CORRECTION_INFO__LAST_ERR_INFO)
+
+static int denali_sw_ecc_fixup(struct mtd_info *mtd,
+ struct denali_nand_info *denali,
+ unsigned long *uncor_ecc_flags, uint8_t *buf)
+{
+ unsigned int ecc_size = denali->nand.ecc.size;
+ unsigned int bitflips = 0;
+ unsigned int max_bitflips = 0;
+ uint32_t err_addr, err_cor_info;
+ unsigned int err_byte, err_sector, err_device;
+ uint8_t err_cor_value;
+ unsigned int prev_sector = 0;
+ uint32_t irq_status;
+
+ denali_reset_irq(denali);
+
+ do {
+ err_addr = ioread32(denali->reg + ECC_ERROR_ADDRESS);
+ err_sector = ECC_SECTOR(err_addr);
+ err_byte = ECC_BYTE(err_addr);
+
+ err_cor_info = ioread32(denali->reg + ERR_CORRECTION_INFO);
+ err_cor_value = ECC_CORRECTION_VALUE(err_cor_info);
+ err_device = ECC_ERR_DEVICE(err_cor_info);
+
+ /* reset the bitflip counter when crossing ECC sector */
+ if (err_sector != prev_sector)
+ bitflips = 0;
+
+ if (ECC_ERROR_UNCORRECTABLE(err_cor_info)) {
+ /*
+ * Check later if this is a real ECC error, or
+ * an erased sector.
+ */
+ *uncor_ecc_flags |= BIT(err_sector);
+ } else if (err_byte < ecc_size) {
+ /*
+ * If err_byte is larger than ecc_size, means error
+ * happened in OOB, so we ignore it. It's no need for
+ * us to correct it err_device is represented the NAND
+ * error bits are happened in if there are more than
+ * one NAND connected.
+ */
+ int offset;
+ unsigned int flips_in_byte;
+
+ offset = (err_sector * ecc_size + err_byte) *
+ denali->devs_per_cs + err_device;
+
+ /* correct the ECC error */
+ flips_in_byte = hweight8(buf[offset] ^ err_cor_value);
+ buf[offset] ^= err_cor_value;
+ mtd->ecc_stats.corrected += flips_in_byte;
+ bitflips += flips_in_byte;
+
+ max_bitflips = max(max_bitflips, bitflips);
+ }
+
+ prev_sector = err_sector;
+ } while (!ECC_LAST_ERR(err_cor_info));
+
+ /*
+ * Once handle all ecc errors, controller will trigger a
+ * ECC_TRANSACTION_DONE interrupt, so here just wait for
+ * a while for this interrupt
+ */
+ irq_status = denali_wait_for_irq(denali, INTR__ECC_TRANSACTION_DONE);
+ if (!(irq_status & INTR__ECC_TRANSACTION_DONE))
+ return -EIO;
+
+ return max_bitflips;
+}
+
+/* programs the controller to either enable/disable DMA transfers */
+static void denali_enable_dma(struct denali_nand_info *denali, bool en)
+{
+ iowrite32(en ? DMA_ENABLE__FLAG : 0, denali->reg + DMA_ENABLE);
+ ioread32(denali->reg + DMA_ENABLE);
+}
+
+static void denali_setup_dma64(struct denali_nand_info *denali,
+ dma_addr_t dma_addr, int page, int write)
+{
+ uint32_t mode;
+ const int page_count = 1;
+
+ mode = DENALI_MAP10 | DENALI_BANK(denali) | page;
+
+ /* DMA is a three step process */
+
+ /*
+ * 1. setup transfer type, interrupt when complete,
+ * burst len = 64 bytes, the number of pages
+ */
+ denali_host_write(denali, mode,
+ 0x01002000 | (64 << 16) | (write << 8) | page_count);
+
+ /* 2. set memory low address */
+ denali_host_write(denali, mode, dma_addr);
+
+ /* 3. set memory high address */
+ denali_host_write(denali, mode, (uint64_t)dma_addr >> 32);
+}
+
+static void denali_setup_dma32(struct denali_nand_info *denali,
+ dma_addr_t dma_addr, int page, int write)
+{
+ uint32_t mode;
+ const int page_count = 1;
+
+ mode = DENALI_MAP10 | DENALI_BANK(denali);
+
+ /* DMA is a four step process */
+
+ /* 1. setup transfer type and # of pages */
+ denali_host_write(denali, mode | page,
+ 0x2000 | (write << 8) | page_count);
+
+ /* 2. set memory high address bits 23:8 */
+ denali_host_write(denali, mode | ((dma_addr >> 16) << 8), 0x2200);
+
+ /* 3. set memory low address bits 23:8 */
+ denali_host_write(denali, mode | ((dma_addr & 0xffff) << 8), 0x2300);
+
+ /* 4. interrupt when complete, burst len = 64 bytes */
+ denali_host_write(denali, mode | 0x14000, 0x2400);
+}
+
+static void denali_setup_dma(struct denali_nand_info *denali,
+ dma_addr_t dma_addr, int page, int write)
+{
+ if (denali->caps & DENALI_CAP_DMA_64BIT)
+ denali_setup_dma64(denali, dma_addr, page, write);
+ else
+ denali_setup_dma32(denali, dma_addr, page, write);
+}
+
+static int denali_pio_read(struct denali_nand_info *denali, void *buf,
+ size_t size, int page, int raw)
+{
+ uint32_t addr = DENALI_BANK(denali) | page;
+ uint32_t *buf32 = (uint32_t *)buf;
+ uint32_t irq_status, ecc_err_mask;
+ int i;
+
+ if (denali->caps & DENALI_CAP_HW_ECC_FIXUP)
+ ecc_err_mask = INTR__ECC_UNCOR_ERR;
+ else
+ ecc_err_mask = INTR__ECC_ERR;
+
+ denali_reset_irq(denali);
+
+ iowrite32(DENALI_MAP01 | addr, denali->host + DENALI_HOST_ADDR);
+ for (i = 0; i < size / 4; i++)
+ *buf32++ = ioread32(denali->host + DENALI_HOST_DATA);
+
+ irq_status = denali_wait_for_irq(denali, INTR__PAGE_XFER_INC);
+ if (!(irq_status & INTR__PAGE_XFER_INC))
+ return -EIO;
+
+ if (irq_status & INTR__ERASED_PAGE)
+ memset(buf, 0xff, size);
+
+ return irq_status & ecc_err_mask ? -EBADMSG : 0;
+}
+
+static int denali_pio_write(struct denali_nand_info *denali,
+ const void *buf, size_t size, int page, int raw)
+{
+ uint32_t addr = DENALI_BANK(denali) | page;
+ const uint32_t *buf32 = (uint32_t *)buf;
+ uint32_t irq_status;
+ int i;
+
+ denali_reset_irq(denali);
+
+ iowrite32(DENALI_MAP01 | addr, denali->host + DENALI_HOST_ADDR);
+ for (i = 0; i < size / 4; i++)
+ iowrite32(*buf32++, denali->host + DENALI_HOST_DATA);
+
+ irq_status = denali_wait_for_irq(denali,
+ INTR__PROGRAM_COMP | INTR__PROGRAM_FAIL);
+ if (!(irq_status & INTR__PROGRAM_COMP))
+ return -EIO;
+
+ return 0;
+}
+
+static int denali_pio_xfer(struct denali_nand_info *denali, void *buf,
+ size_t size, int page, int raw, int write)
+{
+ if (write)
+ return denali_pio_write(denali, buf, size, page, raw);
+ else
+ return denali_pio_read(denali, buf, size, page, raw);
+}
+
+static int denali_dma_xfer(struct denali_nand_info *denali, void *buf,
+ size_t size, int page, int raw, int write)
+{
+ dma_addr_t dma_addr;
+ uint32_t irq_mask, irq_status, ecc_err_mask;
+ enum dma_data_direction dir = write ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
+ int ret = 0;
+
+ dma_addr = dma_map_single(denali->dev, buf, size, dir);
+ if (dma_mapping_error(denali->dev, dma_addr)) {
+ dev_dbg(denali->dev, "Failed to DMA-map buffer. Trying PIO.\n");
+ return denali_pio_xfer(denali, buf, size, page, raw, write);
+ }
+
+ if (write) {
+ /*
+ * INTR__PROGRAM_COMP is never asserted for the DMA transfer.
+ * We can use INTR__DMA_CMD_COMP instead. This flag is asserted
+ * when the page program is completed.
+ */
+ irq_mask = INTR__DMA_CMD_COMP | INTR__PROGRAM_FAIL;
+ ecc_err_mask = 0;
+ } else if (denali->caps & DENALI_CAP_HW_ECC_FIXUP) {
+ irq_mask = INTR__DMA_CMD_COMP;
+ ecc_err_mask = INTR__ECC_UNCOR_ERR;
+ } else {
+ irq_mask = INTR__DMA_CMD_COMP;
+ ecc_err_mask = INTR__ECC_ERR;
+ }
+
+ denali_enable_dma(denali, true);
+
+ denali_reset_irq(denali);
+ denali_setup_dma(denali, dma_addr, page, write);
+
+ /* wait for operation to complete */
+ irq_status = denali_wait_for_irq(denali, irq_mask);
+ if (!(irq_status & INTR__DMA_CMD_COMP))
+ ret = -EIO;
+ else if (irq_status & ecc_err_mask)
+ ret = -EBADMSG;
+
+ denali_enable_dma(denali, false);
+ dma_unmap_single(denali->dev, dma_addr, size, dir);
+
+ if (irq_status & INTR__ERASED_PAGE)
+ memset(buf, 0xff, size);
+
+ return ret;
+}
+
+static int denali_data_xfer(struct denali_nand_info *denali, void *buf,
+ size_t size, int page, int raw, int write)
+{
+ setup_ecc_for_xfer(denali, !raw, raw);
+
+ if (denali->dma_avail)
+ return denali_dma_xfer(denali, buf, size, page, raw, write);
+ else
+ return denali_pio_xfer(denali, buf, size, page, raw, write);
+}
+
+static void denali_oob_xfer(struct mtd_info *mtd, struct nand_chip *chip,
+ int page, int write)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ unsigned int start_cmd = write ? NAND_CMD_SEQIN : NAND_CMD_READ0;
+ unsigned int rnd_cmd = write ? NAND_CMD_RNDIN : NAND_CMD_RNDOUT;
+ int writesize = mtd->writesize;
+ int oobsize = mtd->oobsize;
+ uint8_t *bufpoi = chip->oob_poi;
+ int ecc_steps = chip->ecc.steps;
+ int ecc_size = chip->ecc.size;
+ int ecc_bytes = chip->ecc.bytes;
+ int oob_skip = denali->oob_skip_bytes;
+ size_t size = writesize + oobsize;
+ int i, pos, len;
+
+ /* BBM at the beginning of the OOB area */
+ chip->cmdfunc(mtd, start_cmd, writesize, page);
+ if (write)
+ chip->write_buf(mtd, bufpoi, oob_skip);
+ else
+ chip->read_buf(mtd, bufpoi, oob_skip);
+ bufpoi += oob_skip;
+
+ /* OOB ECC */
+ for (i = 0; i < ecc_steps; i++) {
+ pos = ecc_size + i * (ecc_size + ecc_bytes);
+ len = ecc_bytes;
+
+ if (pos >= writesize)
+ pos += oob_skip;
+ else if (pos + len > writesize)
+ len = writesize - pos;
+
+ chip->cmdfunc(mtd, rnd_cmd, pos, -1);
+ if (write)
+ chip->write_buf(mtd, bufpoi, len);
+ else
+ chip->read_buf(mtd, bufpoi, len);
+ bufpoi += len;
+ if (len < ecc_bytes) {
+ len = ecc_bytes - len;
+ chip->cmdfunc(mtd, rnd_cmd, writesize + oob_skip, -1);
+ if (write)
+ chip->write_buf(mtd, bufpoi, len);
+ else
+ chip->read_buf(mtd, bufpoi, len);
+ bufpoi += len;
+ }
+ }
+
+ /* OOB free */
+ len = oobsize - (bufpoi - chip->oob_poi);
+ chip->cmdfunc(mtd, rnd_cmd, size - len, -1);
+ if (write)
+ chip->write_buf(mtd, bufpoi, len);
+ else
+ chip->read_buf(mtd, bufpoi, len);
+}
+
+static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ int writesize = mtd->writesize;
+ int oobsize = mtd->oobsize;
+ int ecc_steps = chip->ecc.steps;
+ int ecc_size = chip->ecc.size;
+ int ecc_bytes = chip->ecc.bytes;
+ void *dma_buf = denali->buf;
+ int oob_skip = denali->oob_skip_bytes;
+ size_t size = writesize + oobsize;
+ int ret, i, pos, len;
+
+ ret = denali_data_xfer(denali, dma_buf, size, page, 1, 0);
+ if (ret)
+ return ret;
+
+ /* Arrange the buffer for syndrome payload/ecc layout */
+ if (buf) {
+ for (i = 0; i < ecc_steps; i++) {
+ pos = i * (ecc_size + ecc_bytes);
+ len = ecc_size;
+
+ if (pos >= writesize)
+ pos += oob_skip;
+ else if (pos + len > writesize)
+ len = writesize - pos;
+
+ memcpy(buf, dma_buf + pos, len);
+ buf += len;
+ if (len < ecc_size) {
+ len = ecc_size - len;
+ memcpy(buf, dma_buf + writesize + oob_skip,
+ len);
+ buf += len;
+ }
+ }
+ }
+
+ if (oob_required) {
+ uint8_t *oob = chip->oob_poi;
+
+ /* BBM at the beginning of the OOB area */
+ memcpy(oob, dma_buf + writesize, oob_skip);
+ oob += oob_skip;
+
+ /* OOB ECC */
+ for (i = 0; i < ecc_steps; i++) {
+ pos = ecc_size + i * (ecc_size + ecc_bytes);
+ len = ecc_bytes;
+
+ if (pos >= writesize)
+ pos += oob_skip;
+ else if (pos + len > writesize)
+ len = writesize - pos;
+
+ memcpy(oob, dma_buf + pos, len);
+ oob += len;
+ if (len < ecc_bytes) {
+ len = ecc_bytes - len;
+ memcpy(oob, dma_buf + writesize + oob_skip,
+ len);
+ oob += len;
+ }
+ }
+
+ /* OOB free */
+ len = oobsize - (oob - chip->oob_poi);
+ memcpy(oob, dma_buf + size - len, len);
+ }
+
+ return 0;
+}
+
+static int denali_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page)
+{
+ denali_oob_xfer(mtd, chip, page, 0);
+
+ return 0;
+}
+
+static int denali_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ int status;
+
+ denali_reset_irq(denali);
+
+ denali_oob_xfer(mtd, chip, page, 1);
+
+ chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+ status = chip->waitfunc(mtd, chip);
+
+ return status & NAND_STATUS_FAIL ? -EIO : 0;
+}
+
+static int denali_read_page(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ unsigned long uncor_ecc_flags = 0;
+ int stat = 0;
+ int ret;
+
+ ret = denali_data_xfer(denali, buf, mtd->writesize, page, 0, 0);
+ if (ret && ret != -EBADMSG)
+ return ret;
+
+ if (denali->caps & DENALI_CAP_HW_ECC_FIXUP)
+ stat = denali_hw_ecc_fixup(mtd, denali, &uncor_ecc_flags);
+ else if (ret == -EBADMSG)
+ stat = denali_sw_ecc_fixup(mtd, denali, &uncor_ecc_flags, buf);
+
+ if (stat < 0)
+ return stat;
+
+ if (uncor_ecc_flags) {
+ ret = denali_read_oob(mtd, chip, page);
+ if (ret)
+ return ret;
+
+ stat = denali_check_erased_page(mtd, chip, buf,
+ uncor_ecc_flags, stat);
+ }
+
+ return stat;
+}
+
+static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ int writesize = mtd->writesize;
+ int oobsize = mtd->oobsize;
+ int ecc_steps = chip->ecc.steps;
+ int ecc_size = chip->ecc.size;
+ int ecc_bytes = chip->ecc.bytes;
+ void *dma_buf = denali->buf;
+ int oob_skip = denali->oob_skip_bytes;
+ size_t size = writesize + oobsize;
+ int i, pos, len;
+
+ /*
+ * Fill the buffer with 0xff first except the full page transfer.
+ * This simplifies the logic.
+ */
+ if (!buf || !oob_required)
+ memset(dma_buf, 0xff, size);
+
+ /* Arrange the buffer for syndrome payload/ecc layout */
+ if (buf) {
+ for (i = 0; i < ecc_steps; i++) {
+ pos = i * (ecc_size + ecc_bytes);
+ len = ecc_size;
+
+ if (pos >= writesize)
+ pos += oob_skip;
+ else if (pos + len > writesize)
+ len = writesize - pos;
+
+ memcpy(dma_buf + pos, buf, len);
+ buf += len;
+ if (len < ecc_size) {
+ len = ecc_size - len;
+ memcpy(dma_buf + writesize + oob_skip, buf,
+ len);
+ buf += len;
+ }
+ }
+ }
+
+ if (oob_required) {
+ const uint8_t *oob = chip->oob_poi;
+
+ /* BBM at the beginning of the OOB area */
+ memcpy(dma_buf + writesize, oob, oob_skip);
+ oob += oob_skip;
+
+ /* OOB ECC */
+ for (i = 0; i < ecc_steps; i++) {
+ pos = ecc_size + i * (ecc_size + ecc_bytes);
+ len = ecc_bytes;
+
+ if (pos >= writesize)
+ pos += oob_skip;
+ else if (pos + len > writesize)
+ len = writesize - pos;
+
+ memcpy(dma_buf + pos, oob, len);
+ oob += len;
+ if (len < ecc_bytes) {
+ len = ecc_bytes - len;
+ memcpy(dma_buf + writesize + oob_skip, oob,
+ len);
+ oob += len;
+ }
+ }
+
+ /* OOB free */
+ len = oobsize - (oob - chip->oob_poi);
+ memcpy(dma_buf + size - len, oob, len);
+ }
+
+ return denali_data_xfer(denali, dma_buf, size, page, 1, 1);
+}
+
+static int denali_write_page(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+
+ return denali_data_xfer(denali, (void *)buf, mtd->writesize,
+ page, 0, 1);
+}
+
+static void denali_select_chip(struct mtd_info *mtd, int chip)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+
+ denali->active_bank = chip;
+}
+
+static int denali_waitfunc(struct mtd_info *mtd, struct nand_chip *chip)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t irq_status;
+
+ /* R/B# pin transitioned from low to high? */
+ irq_status = denali_wait_for_irq(denali, INTR__INT_ACT);
+
+ return irq_status & INTR__INT_ACT ? 0 : NAND_STATUS_FAIL;
+}
+
+static int denali_erase(struct mtd_info *mtd, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t irq_status;
+
+ denali_reset_irq(denali);
+
+ denali_host_write(denali, DENALI_MAP10 | DENALI_BANK(denali) | page,
+ DENALI_ERASE);
+
+ /* wait for erase to complete or failure to occur */
+ irq_status = denali_wait_for_irq(denali,
+ INTR__ERASE_COMP | INTR__ERASE_FAIL);
+
+ return irq_status & INTR__ERASE_COMP ? 0 : NAND_STATUS_FAIL;
+}
+
+static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr,
+ const struct nand_data_interface *conf)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ const struct nand_sdr_timings *timings;
+ unsigned long t_clk;
+ int acc_clks, re_2_we, re_2_re, we_2_re, addr_2_data;
+ int rdwr_en_lo, rdwr_en_hi, rdwr_en_lo_hi, cs_setup;
+ int addr_2_data_mask;
+ uint32_t tmp;
+
+ timings = nand_get_sdr_timings(conf);
+ if (IS_ERR(timings))
+ return PTR_ERR(timings);
+
+ /* clk_x period in picoseconds */
+ t_clk = DIV_ROUND_DOWN_ULL(1000000000000ULL, denali->clk_x_rate);
+ if (!t_clk)
+ return -EINVAL;
+
+ if (chipnr == NAND_DATA_IFACE_CHECK_ONLY)
+ return 0;
+
+ /* tREA -> ACC_CLKS */
+ acc_clks = DIV_ROUND_UP(timings->tREA_max, t_clk);
+ acc_clks = min_t(int, acc_clks, ACC_CLKS__VALUE);
+
+ tmp = ioread32(denali->reg + ACC_CLKS);
+ tmp &= ~ACC_CLKS__VALUE;
+ tmp |= acc_clks;
+ iowrite32(tmp, denali->reg + ACC_CLKS);
+
+ /* tRWH -> RE_2_WE */
+ re_2_we = DIV_ROUND_UP(timings->tRHW_min, t_clk);
+ re_2_we = min_t(int, re_2_we, RE_2_WE__VALUE);
+
+ tmp = ioread32(denali->reg + RE_2_WE);
+ tmp &= ~RE_2_WE__VALUE;
+ tmp |= re_2_we;
+ iowrite32(tmp, denali->reg + RE_2_WE);
+
+ /* tRHZ -> RE_2_RE */
+ re_2_re = DIV_ROUND_UP(timings->tRHZ_max, t_clk);
+ re_2_re = min_t(int, re_2_re, RE_2_RE__VALUE);
+
+ tmp = ioread32(denali->reg + RE_2_RE);
+ tmp &= ~RE_2_RE__VALUE;
+ tmp |= re_2_re;
+ iowrite32(tmp, denali->reg + RE_2_RE);
+
+ /* tWHR -> WE_2_RE */
+ we_2_re = DIV_ROUND_UP(timings->tWHR_min, t_clk);
+ we_2_re = min_t(int, we_2_re, TWHR2_AND_WE_2_RE__WE_2_RE);
+
+ tmp = ioread32(denali->reg + TWHR2_AND_WE_2_RE);
+ tmp &= ~TWHR2_AND_WE_2_RE__WE_2_RE;
+ tmp |= we_2_re;
+ iowrite32(tmp, denali->reg + TWHR2_AND_WE_2_RE);
+
+ /* tADL -> ADDR_2_DATA */
+
+ /* for older versions, ADDR_2_DATA is only 6 bit wide */
+ addr_2_data_mask = TCWAW_AND_ADDR_2_DATA__ADDR_2_DATA;
+ if (denali->revision < 0x0501)
+ addr_2_data_mask >>= 1;
+
+ addr_2_data = DIV_ROUND_UP(timings->tADL_min, t_clk);
+ addr_2_data = min_t(int, addr_2_data, addr_2_data_mask);
+
+ tmp = ioread32(denali->reg + TCWAW_AND_ADDR_2_DATA);
+ tmp &= ~addr_2_data_mask;
+ tmp |= addr_2_data;
+ iowrite32(tmp, denali->reg + TCWAW_AND_ADDR_2_DATA);
+
+ /* tREH, tWH -> RDWR_EN_HI_CNT */
+ rdwr_en_hi = DIV_ROUND_UP(max(timings->tREH_min, timings->tWH_min),
+ t_clk);
+ rdwr_en_hi = min_t(int, rdwr_en_hi, RDWR_EN_HI_CNT__VALUE);
+
+ tmp = ioread32(denali->reg + RDWR_EN_HI_CNT);
+ tmp &= ~RDWR_EN_HI_CNT__VALUE;
+ tmp |= rdwr_en_hi;
+ iowrite32(tmp, denali->reg + RDWR_EN_HI_CNT);
+
+ /* tRP, tWP -> RDWR_EN_LO_CNT */
+ rdwr_en_lo = DIV_ROUND_UP(max(timings->tRP_min, timings->tWP_min),
+ t_clk);
+ rdwr_en_lo_hi = DIV_ROUND_UP(max(timings->tRC_min, timings->tWC_min),
+ t_clk);
+ rdwr_en_lo_hi = max(rdwr_en_lo_hi, DENALI_CLK_X_MULT);
+ rdwr_en_lo = max(rdwr_en_lo, rdwr_en_lo_hi - rdwr_en_hi);
+ rdwr_en_lo = min_t(int, rdwr_en_lo, RDWR_EN_LO_CNT__VALUE);
+
+ tmp = ioread32(denali->reg + RDWR_EN_LO_CNT);
+ tmp &= ~RDWR_EN_LO_CNT__VALUE;
+ tmp |= rdwr_en_lo;
+ iowrite32(tmp, denali->reg + RDWR_EN_LO_CNT);
+
+ /* tCS, tCEA -> CS_SETUP_CNT */
+ cs_setup = max3((int)DIV_ROUND_UP(timings->tCS_min, t_clk) - rdwr_en_lo,
+ (int)DIV_ROUND_UP(timings->tCEA_max, t_clk) - acc_clks,
+ 0);
+ cs_setup = min_t(int, cs_setup, CS_SETUP_CNT__VALUE);
+
+ tmp = ioread32(denali->reg + CS_SETUP_CNT);
+ tmp &= ~CS_SETUP_CNT__VALUE;
+ tmp |= cs_setup;
+ iowrite32(tmp, denali->reg + CS_SETUP_CNT);
+
+ return 0;
+}
+
+static void denali_reset_banks(struct denali_nand_info *denali)
+{
+ u32 irq_status;
+ int i;
+
+ for (i = 0; i < denali->max_banks; i++) {
+ denali->active_bank = i;
+
+ denali_reset_irq(denali);
+
+ iowrite32(DEVICE_RESET__BANK(i),
+ denali->reg + DEVICE_RESET);
+
+ irq_status = denali_wait_for_irq(denali,
+ INTR__RST_COMP | INTR__INT_ACT | INTR__TIME_OUT);
+ if (!(irq_status & INTR__INT_ACT))
+ break;
+ }
+
+ dev_dbg(denali->dev, "%d chips connected\n", i);
+ denali->max_banks = i;
+}
+
+static void denali_hw_init(struct denali_nand_info *denali)
+{
+ /*
+ * The REVISION register may not be reliable. Platforms are allowed to
+ * override it.
+ */
+ if (!denali->revision)
+ denali->revision = swab16(ioread32(denali->reg + REVISION));
+
+ /*
+ * tell driver how many bit controller will skip before
+ * writing ECC code in OOB, this register may be already
+ * set by firmware. So we read this value out.
+ * if this value is 0, just let it be.
+ */
+ denali->oob_skip_bytes = ioread32(denali->reg + SPARE_AREA_SKIP_BYTES);
+ detect_max_banks(denali);
+ iowrite32(0x0F, denali->reg + RB_PIN_ENABLED);
+ iowrite32(CHIP_EN_DONT_CARE__FLAG, denali->reg + CHIP_ENABLE_DONT_CARE);
+
+ iowrite32(0xffff, denali->reg + SPARE_AREA_MARKER);
+
+ /* Should set value for these registers when init */
+ iowrite32(0, denali->reg + TWO_ROW_ADDR_CYCLES);
+ iowrite32(1, denali->reg + ECC_ENABLE);
+}
+
+int denali_calc_ecc_bytes(int step_size, int strength)
+{
+ /* BCH code. Denali requires ecc.bytes to be multiple of 2 */
+ return DIV_ROUND_UP(strength * fls(step_size * 8), 16) * 2;
+}
+EXPORT_SYMBOL(denali_calc_ecc_bytes);
+
+static int denali_ecc_setup(struct mtd_info *mtd, struct nand_chip *chip,
+ struct denali_nand_info *denali)
+{
+ int oobavail = mtd->oobsize - denali->oob_skip_bytes;
+ int ret;
+
+ /*
+ * If .size and .strength are already set (usually by DT),
+ * check if they are supported by this controller.
+ */
+ if (chip->ecc.size && chip->ecc.strength)
+ return nand_check_ecc_caps(chip, denali->ecc_caps, oobavail);
+
+ /*
+ * We want .size and .strength closest to the chip's requirement
+ * unless NAND_ECC_MAXIMIZE is requested.
+ */
+ if (!(chip->ecc.options & NAND_ECC_MAXIMIZE)) {
+ ret = nand_match_ecc_req(chip, denali->ecc_caps, oobavail);
+ if (!ret)
+ return 0;
+ }
+
+ /* Max ECC strength is the last thing we can do */
+ return nand_maximize_ecc(chip, denali->ecc_caps, oobavail);
+}
+
+static int denali_ooblayout_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ struct nand_chip *chip = mtd_to_nand(mtd);
+
+ if (section)
+ return -ERANGE;
+
+ oobregion->offset = denali->oob_skip_bytes;
+ oobregion->length = chip->ecc.total;
+
+ return 0;
+}
+
+static int denali_ooblayout_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ struct nand_chip *chip = mtd_to_nand(mtd);
+
+ if (section)
+ return -ERANGE;
+
+ oobregion->offset = chip->ecc.total + denali->oob_skip_bytes;
+ oobregion->length = mtd->oobsize - oobregion->offset;
+
+ return 0;
+}
+
+static const struct mtd_ooblayout_ops denali_ooblayout_ops = {
+ .ecc = denali_ooblayout_ecc,
+ .free = denali_ooblayout_free,
+};
+
+/* initialize driver data structures */
+static void denali_drv_init(struct denali_nand_info *denali)
+{
+ /*
+ * the completion object will be used to notify
+ * the callee that the interrupt is done
+ */
+ init_completion(&denali->complete);
+
+ /*
+ * the spinlock will be used to synchronize the ISR with any
+ * element that might be access shared data (interrupt status)
+ */
+ spin_lock_init(&denali->irq_lock);
+}
+
+static int denali_multidev_fixup(struct denali_nand_info *denali)
+{
+ struct nand_chip *chip = &denali->nand;
+ struct mtd_info *mtd = nand_to_mtd(chip);
+
+ /*
+ * Support for multi device:
+ * When the IP configuration is x16 capable and two x8 chips are
+ * connected in parallel, DEVICES_CONNECTED should be set to 2.
+ * In this case, the core framework knows nothing about this fact,
+ * so we should tell it the _logical_ pagesize and anything necessary.
+ */
+ denali->devs_per_cs = ioread32(denali->reg + DEVICES_CONNECTED);
+
+ /*
+ * On some SoCs, DEVICES_CONNECTED is not auto-detected.
+ * For those, DEVICES_CONNECTED is left to 0. Set 1 if it is the case.
+ */
+ if (denali->devs_per_cs == 0) {
+ denali->devs_per_cs = 1;
+ iowrite32(1, denali->reg + DEVICES_CONNECTED);
+ }
+
+ if (denali->devs_per_cs == 1)
+ return 0;
+
+ if (denali->devs_per_cs != 2) {
+ dev_err(denali->dev, "unsupported number of devices %d\n",
+ denali->devs_per_cs);
+ return -EINVAL;
+ }
+
+ /* 2 chips in parallel */
+ mtd->size <<= 1;
+ mtd->erasesize <<= 1;
+ mtd->writesize <<= 1;
+ mtd->oobsize <<= 1;
+ chip->chipsize <<= 1;
+ chip->page_shift += 1;
+ chip->phys_erase_shift += 1;
+ chip->bbt_erase_shift += 1;
+ chip->chip_shift += 1;
+ chip->pagemask <<= 1;
+ chip->ecc.size <<= 1;
+ chip->ecc.bytes <<= 1;
+ chip->ecc.strength <<= 1;
+ denali->oob_skip_bytes <<= 1;
+
+ return 0;
+}
+
+int denali_init(struct denali_nand_info *denali)
+{
+ struct nand_chip *chip = &denali->nand;
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ int ret;
+
+ mtd->dev.parent = denali->dev;
+ denali_hw_init(denali);
+ denali_drv_init(denali);
+
+ denali_clear_irq_all(denali);
+
+ /* Request IRQ after all the hardware initialization is finished */
+ ret = devm_request_irq(denali->dev, denali->irq, denali_isr,
+ IRQF_SHARED, DENALI_NAND_NAME, denali);
+ if (ret) {
+ dev_err(denali->dev, "Unable to request IRQ\n");
+ return ret;
+ }
+
+ denali_enable_irq(denali);
+ denali_reset_banks(denali);
+
+ denali->active_bank = DENALI_INVALID_BANK;
+
+ nand_set_flash_node(chip, denali->dev->of_node);
+ /* Fallback to the default name if DT did not give "label" property */
+ if (!mtd->name)
+ mtd->name = "denali-nand";
+
+ /* register the driver with the NAND core subsystem */
+ chip->select_chip = denali_select_chip;
+ chip->read_byte = denali_read_byte;
+ chip->write_byte = denali_write_byte;
+ chip->read_word = denali_read_word;
+ chip->cmd_ctrl = denali_cmd_ctrl;
+ chip->dev_ready = denali_dev_ready;
+ chip->waitfunc = denali_waitfunc;
+
+ /* clk rate info is needed for setup_data_interface */
+ if (denali->clk_x_rate)
+ chip->setup_data_interface = denali_setup_data_interface;
+
+ /*
+ * scan for NAND devices attached to the controller
+ * this is the first stage in a two step process to register
+ * with the nand subsystem
+ */
+ ret = nand_scan_ident(mtd, denali->max_banks, NULL);
+ if (ret)
+ goto disable_irq;
+
+ if (ioread32(denali->reg + FEATURES) & FEATURES__DMA)
+ denali->dma_avail = 1;
+
+ if (denali->dma_avail) {
+ int dma_bit = denali->caps & DENALI_CAP_DMA_64BIT ? 64 : 32;
+
+ ret = dma_set_mask(denali->dev, DMA_BIT_MASK(dma_bit));
+ if (ret) {
+ dev_info(denali->dev,
+ "Failed to set DMA mask. Disabling DMA.\n");
+ denali->dma_avail = 0;
+ }
+ }
+
+ if (denali->dma_avail) {
+ chip->options |= NAND_USE_BOUNCE_BUFFER;
+ chip->buf_align = 16;
+ }
+
+ /*
+ * second stage of the NAND scan
+ * this stage requires information regarding ECC and
+ * bad block management.
+ */
+
+ chip->bbt_options |= NAND_BBT_USE_FLASH;
+ chip->bbt_options |= NAND_BBT_NO_OOB;
+
+ chip->ecc.mode = NAND_ECC_HW_SYNDROME;
+
+ /* no subpage writes on denali */
+ chip->options |= NAND_NO_SUBPAGE_WRITE;
+
+ ret = denali_ecc_setup(mtd, chip, denali);
+ if (ret) {
+ dev_err(denali->dev, "Failed to setup ECC settings.\n");
+ goto disable_irq;
+ }
+
+ dev_dbg(denali->dev,
+ "chosen ECC settings: step=%d, strength=%d, bytes=%d\n",
+ chip->ecc.size, chip->ecc.strength, chip->ecc.bytes);
+
+ iowrite32(MAKE_ECC_CORRECTION(chip->ecc.strength, 1),
+ denali->reg + ECC_CORRECTION);
+ iowrite32(mtd->erasesize / mtd->writesize,
+ denali->reg + PAGES_PER_BLOCK);
+ iowrite32(chip->options & NAND_BUSWIDTH_16 ? 1 : 0,
+ denali->reg + DEVICE_WIDTH);
+ iowrite32(mtd->writesize, denali->reg + DEVICE_MAIN_AREA_SIZE);
+ iowrite32(mtd->oobsize, denali->reg + DEVICE_SPARE_AREA_SIZE);
+
+ iowrite32(chip->ecc.size, denali->reg + CFG_DATA_BLOCK_SIZE);
+ iowrite32(chip->ecc.size, denali->reg + CFG_LAST_DATA_BLOCK_SIZE);
+ /* chip->ecc.steps is set by nand_scan_tail(); not available here */
+ iowrite32(mtd->writesize / chip->ecc.size,
+ denali->reg + CFG_NUM_DATA_BLOCKS);
+
+ mtd_set_ooblayout(mtd, &denali_ooblayout_ops);
+
+ if (chip->options & NAND_BUSWIDTH_16) {
+ chip->read_buf = denali_read_buf16;
+ chip->write_buf = denali_write_buf16;
+ } else {
+ chip->read_buf = denali_read_buf;
+ chip->write_buf = denali_write_buf;
+ }
+ chip->ecc.options |= NAND_ECC_CUSTOM_PAGE_ACCESS;
+ chip->ecc.read_page = denali_read_page;
+ chip->ecc.read_page_raw = denali_read_page_raw;
+ chip->ecc.write_page = denali_write_page;
+ chip->ecc.write_page_raw = denali_write_page_raw;
+ chip->ecc.read_oob = denali_read_oob;
+ chip->ecc.write_oob = denali_write_oob;
+ chip->erase = denali_erase;
+
+ ret = denali_multidev_fixup(denali);
+ if (ret)
+ goto disable_irq;
+
+ /*
+ * This buffer is DMA-mapped by denali_{read,write}_page_raw. Do not
+ * use devm_kmalloc() because the memory allocated by devm_ does not
+ * guarantee DMA-safe alignment.
+ */
+ denali->buf = kmalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL);
+ if (!denali->buf) {
+ ret = -ENOMEM;
+ goto disable_irq;
+ }
+
+ ret = nand_scan_tail(mtd);
+ if (ret)
+ goto free_buf;
+
+ ret = mtd_device_register(mtd, NULL, 0);
+ if (ret) {
+ dev_err(denali->dev, "Failed to register MTD: %d\n", ret);
+ goto free_buf;
+ }
+ return 0;
+
+free_buf:
+ kfree(denali->buf);
+disable_irq:
+ denali_disable_irq(denali);
+
+ return ret;
+}
+EXPORT_SYMBOL(denali_init);
+
+/* driver exit point */
+void denali_remove(struct denali_nand_info *denali)
+{
+ nand_release(&denali->nand);
+ kfree(denali->buf);
+ denali_disable_irq(denali);
+}
+EXPORT_SYMBOL(denali_remove);