[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/drivers/usb/gadget/Kconfig b/src/kernel/linux/v4.14/drivers/usb/gadget/Kconfig
new file mode 100644
index 0000000..f572b64
--- /dev/null
+++ b/src/kernel/linux/v4.14/drivers/usb/gadget/Kconfig
@@ -0,0 +1,545 @@
+#
+# USB Gadget support on a system involves
+# (a) a peripheral controller, and
+# (b) the gadget driver using it.
+#
+# NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !!
+#
+# - Host systems (like PCs) need CONFIG_USB (with "A" jacks).
+# - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks).
+# - Some systems have both kinds of controllers.
+#
+# With help from a special transceiver and a "Mini-AB" jack, systems with
+# both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG).
+#
+
+menuconfig USB_GADGET
+ tristate "USB Gadget Support"
+ select USB_COMMON
+ select NLS
+ help
+ USB is a master/slave protocol, organized with one master
+ host (such as a PC) controlling up to 127 peripheral devices.
+ The USB hardware is asymmetric, which makes it easier to set up:
+ you can't connect a "to-the-host" connector to a peripheral.
+
+ Linux can run in the host, or in the peripheral. In both cases
+ you need a low level bus controller driver, and some software
+ talking to it. Peripheral controllers are often discrete silicon,
+ or are integrated with the CPU in a microcontroller. The more
+ familiar host side controllers have names like "EHCI", "OHCI",
+ or "UHCI", and are usually integrated into southbridges on PC
+ motherboards.
+
+ Enable this configuration option if you want to run Linux inside
+ a USB peripheral device. Configure one hardware driver for your
+ peripheral/device side bus controller, and a "gadget driver" for
+ your peripheral protocol. (If you use modular gadget drivers,
+ you may configure more than one.)
+
+ If in doubt, say "N" and don't enable these drivers; most people
+ don't have this kind of hardware (except maybe inside Linux PDAs).
+
+ For more information, see <http://www.linux-usb.org/gadget> and
+ the kernel documentation for this API.
+
+if USB_GADGET
+
+config USB_GADGET_DEBUG
+ bool "Debugging messages (DEVELOPMENT)"
+ depends on DEBUG_KERNEL
+ help
+ Many controller and gadget drivers will print some debugging
+ messages if you use this option to ask for those messages.
+
+ Avoid enabling these messages, even if you're actively
+ debugging such a driver. Many drivers will emit so many
+ messages that the driver timings are affected, which will
+ either create new failure modes or remove the one you're
+ trying to track down. Never enable these messages for a
+ production build.
+
+config USB_GADGET_VERBOSE
+ bool "Verbose debugging Messages (DEVELOPMENT)"
+ depends on USB_GADGET_DEBUG
+ help
+ Many controller and gadget drivers will print verbose debugging
+ messages if you use this option to ask for those messages.
+
+ Avoid enabling these messages, even if you're actively
+ debugging such a driver. Many drivers will emit so many
+ messages that the driver timings are affected, which will
+ either create new failure modes or remove the one you're
+ trying to track down. Never enable these messages for a
+ production build.
+
+config USB_GADGET_DEBUG_FILES
+ bool "Debugging information files (DEVELOPMENT)"
+ depends on PROC_FS
+ help
+ Some of the drivers in the "gadget" framework can expose
+ debugging information in files such as /proc/driver/udc
+ (for a peripheral controller). The information in these
+ files may help when you're troubleshooting or bringing up a
+ driver on a new board. Enable these files by choosing "Y"
+ here. If in doubt, or to conserve kernel memory, say "N".
+
+config USB_GADGET_DEBUG_FS
+ bool "Debugging information files in debugfs (DEVELOPMENT)"
+ depends on DEBUG_FS
+ help
+ Some of the drivers in the "gadget" framework can expose
+ debugging information in files under /sys/kernel/debug/.
+ The information in these files may help when you're
+ troubleshooting or bringing up a driver on a new board.
+ Enable these files by choosing "Y" here. If in doubt, or
+ to conserve kernel memory, say "N".
+
+config USB_GADGET_VBUS_DRAW
+ int "Maximum VBUS Power usage (2-500 mA)"
+ range 2 500
+ default 2
+ help
+ Some devices need to draw power from USB when they are
+ configured, perhaps to operate circuitry or to recharge
+ batteries. This is in addition to any local power supply,
+ such as an AC adapter or batteries.
+
+ Enter the maximum power your device draws through USB, in
+ milliAmperes. The permitted range of values is 2 - 500 mA;
+ 0 mA would be legal, but can make some hosts misbehave.
+
+ This value will be used except for system-specific gadget
+ drivers that have more specific information.
+
+config USB_GADGET_STORAGE_NUM_BUFFERS
+ int "Number of storage pipeline buffers"
+ range 2 256
+ default 2
+ help
+ Usually 2 buffers are enough to establish a good buffering
+ pipeline. The number may be increased in order to compensate
+ for a bursty VFS behaviour. For instance there may be CPU wake up
+ latencies that makes the VFS to appear bursty in a system with
+ an CPU on-demand governor. Especially if DMA is doing IO to
+ offload the CPU. In this case the CPU will go into power
+ save often and spin up occasionally to move data within VFS.
+ If selecting USB_GADGET_DEBUG_FILES this value may be set by
+ a module parameter as well.
+ If unsure, say 2.
+
+config U_SERIAL_CONSOLE
+ bool "Serial gadget console support"
+ depends on USB_U_SERIAL
+ help
+ It supports the serial gadget can be used as a console.
+
+source "drivers/usb/gadget/udc/Kconfig"
+
+#
+# USB Gadget Drivers
+#
+
+# composite based drivers
+config USB_LIBCOMPOSITE
+ tristate
+ select CONFIGFS_FS
+ depends on USB_GADGET
+
+config USB_F_ACM
+ tristate
+
+config USB_F_SS_LB
+ tristate
+
+config USB_U_SERIAL
+ tristate
+
+config USB_U_ETHER
+ tristate
+
+config USB_U_AUDIO
+ tristate
+
+config USB_F_SERIAL
+ tristate
+
+config USB_F_OBEX
+ tristate
+
+config USB_F_NCM
+ tristate
+
+config USB_F_ECM
+ tristate
+
+config USB_F_PHONET
+ tristate
+
+config USB_F_EEM
+ tristate
+
+config USB_F_SUBSET
+ tristate
+
+config USB_F_RNDIS
+ tristate
+
+config USB_F_MASS_STORAGE
+ tristate
+
+config USB_F_FS
+ tristate
+
+config USB_F_UAC1
+ tristate
+
+config USB_F_UAC1_LEGACY
+ tristate
+
+config USB_F_UAC2
+ tristate
+
+config USB_F_UVC
+ tristate
+
+config USB_F_MIDI
+ tristate
+
+config USB_F_HID
+ tristate
+
+config USB_F_PRINTER
+ tristate
+
+config USB_F_TCM
+ tristate
+
+config USB_F_AUDIO_SRC
+ tristate
+
+config USB_F_ACC
+ tristate
+
+# this first set of drivers all depend on bulk-capable hardware.
+
+config USB_CONFIGFS
+ tristate "USB Gadget functions configurable through configfs"
+ select USB_LIBCOMPOSITE
+ help
+ A Linux USB "gadget" can be set up through configfs.
+ If this is the case, the USB functions (which from the host's
+ perspective are seen as interfaces) and configurations are
+ specified simply by creating appropriate directories in configfs.
+ Associating functions with configurations is done by creating
+ appropriate symbolic links.
+ For more information see Documentation/usb/gadget_configfs.txt.
+
+config USB_CONFIGFS_SERIAL
+ bool "Generic serial bulk in/out"
+ depends on USB_CONFIGFS
+ depends on TTY
+ select USB_U_SERIAL
+ select USB_F_SERIAL
+ help
+ The function talks to the Linux-USB generic serial driver.
+
+config USB_CONFIGFS_ACM
+ bool "Abstract Control Model (CDC ACM)"
+ depends on USB_CONFIGFS
+ depends on TTY
+ select USB_U_SERIAL
+ select USB_F_ACM
+ help
+ ACM serial link. This function can be used to interoperate with
+ MS-Windows hosts or with the Linux-USB "cdc-acm" driver.
+
+config USB_CONFIGFS_OBEX
+ bool "Object Exchange Model (CDC OBEX)"
+ depends on USB_CONFIGFS
+ depends on TTY
+ select USB_U_SERIAL
+ select USB_F_OBEX
+ help
+ You will need a user space OBEX server talking to /dev/ttyGS*,
+ since the kernel itself doesn't implement the OBEX protocol.
+
+config USB_CONFIGFS_NCM
+ bool "Network Control Model (CDC NCM)"
+ depends on USB_CONFIGFS
+ depends on NET
+ select USB_U_ETHER
+ select USB_F_NCM
+ help
+ NCM is an advanced protocol for Ethernet encapsulation, allows
+ grouping of several ethernet frames into one USB transfer and
+ different alignment possibilities.
+
+config USB_CONFIGFS_ECM
+ bool "Ethernet Control Model (CDC ECM)"
+ depends on USB_CONFIGFS
+ depends on NET
+ select USB_U_ETHER
+ select USB_F_ECM
+ help
+ The "Communication Device Class" (CDC) Ethernet Control Model.
+ That protocol is often avoided with pure Ethernet adapters, in
+ favor of simpler vendor-specific hardware, but is widely
+ supported by firmware for smart network devices.
+
+config USB_CONFIGFS_ECM_SUBSET
+ bool "Ethernet Control Model (CDC ECM) subset"
+ depends on USB_CONFIGFS
+ depends on NET
+ select USB_U_ETHER
+ select USB_F_SUBSET
+ help
+ On hardware that can't implement the full protocol,
+ a simple CDC subset is used, placing fewer demands on USB.
+
+config USB_CONFIGFS_RNDIS
+ bool "RNDIS"
+ depends on USB_CONFIGFS
+ depends on NET
+ select USB_U_ETHER
+ select USB_F_RNDIS
+ help
+ Microsoft Windows XP bundles the "Remote NDIS" (RNDIS) protocol,
+ and Microsoft provides redistributable binary RNDIS drivers for
+ older versions of Windows.
+
+ To make MS-Windows work with this, use Documentation/usb/linux.inf
+ as the "driver info file". For versions of MS-Windows older than
+ XP, you'll need to download drivers from Microsoft's website; a URL
+ is given in comments found in that info file.
+
+config USB_CONFIGFS_EEM
+ bool "Ethernet Emulation Model (EEM)"
+ depends on USB_CONFIGFS
+ depends on NET
+ select USB_U_ETHER
+ select USB_F_EEM
+ help
+ CDC EEM is a newer USB standard that is somewhat simpler than CDC ECM
+ and therefore can be supported by more hardware. Technically ECM and
+ EEM are designed for different applications. The ECM model extends
+ the network interface to the target (e.g. a USB cable modem), and the
+ EEM model is for mobile devices to communicate with hosts using
+ ethernet over USB. For Linux gadgets, however, the interface with
+ the host is the same (a usbX device), so the differences are minimal.
+
+config USB_CONFIGFS_PHONET
+ bool "Phonet protocol"
+ depends on USB_CONFIGFS
+ depends on NET
+ depends on PHONET
+ select USB_U_ETHER
+ select USB_F_PHONET
+ help
+ The Phonet protocol implementation for USB device.
+
+config USB_CONFIGFS_MASS_STORAGE
+ bool "Mass storage"
+ depends on USB_CONFIGFS
+ depends on BLOCK
+ select USB_F_MASS_STORAGE
+ help
+ The Mass Storage Gadget acts as a USB Mass Storage disk drive.
+ As its storage repository it can use a regular file or a block
+ device (in much the same way as the "loop" device driver),
+ specified as a module parameter or sysfs option.
+
+config USB_CONFIGFS_F_LB_SS
+ bool "Loopback and sourcesink function (for testing)"
+ depends on USB_CONFIGFS
+ select USB_F_SS_LB
+ help
+ Loopback function loops back a configurable number of transfers.
+ Sourcesink function either sinks and sources bulk data.
+ It also implements control requests, for "chapter 9" conformance.
+ Make this be the first driver you try using on top of any new
+ USB peripheral controller driver. Then you can use host-side
+ test software, like the "usbtest" driver, to put your hardware
+ and its driver through a basic set of functional tests.
+
+config USB_CONFIGFS_F_FS
+ bool "Function filesystem (FunctionFS)"
+ depends on USB_CONFIGFS
+ select USB_F_FS
+ help
+ The Function Filesystem (FunctionFS) lets one create USB
+ composite functions in user space in the same way GadgetFS
+ lets one create USB gadgets in user space. This allows creation
+ of composite gadgets such that some of the functions are
+ implemented in kernel space (for instance Ethernet, serial or
+ mass storage) and other are implemented in user space.
+
+config USB_CONFIGFS_F_ACC
+ boolean "Accessory gadget"
+ depends on USB_CONFIGFS
+ select USB_F_ACC
+ help
+ USB gadget Accessory support
+
+config USB_CONFIGFS_F_AUDIO_SRC
+ boolean "Audio Source gadget"
+ depends on USB_CONFIGFS && USB_CONFIGFS_F_ACC
+ depends on SND
+ select SND_PCM
+ select USB_F_AUDIO_SRC
+ help
+ USB gadget Audio Source support
+
+config USB_CONFIGFS_UEVENT
+ boolean "Uevent notification of Gadget state"
+ depends on USB_CONFIGFS
+ help
+ Enable uevent notifications to userspace when the gadget
+ state changes. The gadget can be in any of the following
+ three states: "CONNECTED/DISCONNECTED/CONFIGURED"
+
+config USB_CONFIGFS_F_UAC1
+ bool "Audio Class 1.0"
+ depends on USB_CONFIGFS
+ depends on SND
+ select USB_LIBCOMPOSITE
+ select SND_PCM
+ select USB_U_AUDIO
+ select USB_F_UAC1
+ help
+ This Audio function implements 1 AudioControl interface,
+ 1 AudioStreaming Interface each for USB-OUT and USB-IN.
+ This driver doesn't expect any real Audio codec to be present
+ on the device - the audio streams are simply sinked to and
+ sourced from a virtual ALSA sound card created. The user-space
+ application may choose to do whatever it wants with the data
+ received from the USB Host and choose to provide whatever it
+ wants as audio data to the USB Host.
+
+config USB_CONFIGFS_F_UAC1_LEGACY
+ bool "Audio Class 1.0 (legacy implementation)"
+ depends on USB_CONFIGFS
+ depends on SND
+ select USB_LIBCOMPOSITE
+ select SND_PCM
+ select USB_F_UAC1_LEGACY
+ help
+ This Audio function implements 1 AudioControl interface,
+ 1 AudioStreaming Interface each for USB-OUT and USB-IN.
+ This is a legacy driver and requires a real Audio codec
+ to be present on the device.
+
+config USB_CONFIGFS_F_UAC2
+ bool "Audio Class 2.0"
+ depends on USB_CONFIGFS
+ depends on SND
+ select USB_LIBCOMPOSITE
+ select SND_PCM
+ select USB_U_AUDIO
+ select USB_F_UAC2
+ help
+ This Audio function is compatible with USB Audio Class
+ specification 2.0. It implements 1 AudioControl interface,
+ 1 AudioStreaming Interface each for USB-OUT and USB-IN.
+ This driver doesn't expect any real Audio codec to be present
+ on the device - the audio streams are simply sinked to and
+ sourced from a virtual ALSA sound card created. The user-space
+ application may choose to do whatever it wants with the data
+ received from the USB Host and choose to provide whatever it
+ wants as audio data to the USB Host.
+
+config USB_CONFIGFS_F_MIDI
+ bool "MIDI function"
+ depends on USB_CONFIGFS
+ depends on SND
+ select USB_LIBCOMPOSITE
+ select SND_RAWMIDI
+ select USB_F_MIDI
+ help
+ The MIDI Function acts as a USB Audio device, with one MIDI
+ input and one MIDI output. These MIDI jacks appear as
+ a sound "card" in the ALSA sound system. Other MIDI
+ connections can then be made on the gadget system, using
+ ALSA's aconnect utility etc.
+
+config USB_CONFIGFS_F_HID
+ bool "HID function"
+ depends on USB_CONFIGFS
+ select USB_F_HID
+ help
+ The HID function driver provides generic emulation of USB
+ Human Interface Devices (HID).
+
+ For more information, see Documentation/usb/gadget_hid.txt.
+
+config USB_CONFIGFS_F_UVC
+ bool "USB Webcam function"
+ depends on USB_CONFIGFS
+ depends on VIDEO_V4L2
+ depends on VIDEO_DEV
+ select VIDEOBUF2_VMALLOC
+ select USB_F_UVC
+ help
+ The Webcam function acts as a composite USB Audio and Video Class
+ device. It provides a userspace API to process UVC control requests
+ and stream video data to the host.
+
+config USB_CONFIGFS_F_PRINTER
+ bool "Printer function"
+ select USB_F_PRINTER
+ depends on USB_CONFIGFS
+ help
+ The Printer function channels data between the USB host and a
+ userspace program driving the print engine. The user space
+ program reads and writes the device file /dev/g_printer<X> to
+ receive or send printer data. It can use ioctl calls to
+ the device file to get or set printer status.
+
+ For more information, see Documentation/usb/gadget_printer.txt
+ which includes sample code for accessing the device file.
+
+config USB_CONFIGFS_F_TCM
+ bool "USB Gadget Target Fabric"
+ depends on TARGET_CORE
+ depends on USB_CONFIGFS
+ select USB_LIBCOMPOSITE
+ select USB_F_TCM
+ help
+ This fabric is a USB gadget component. Two USB protocols are
+ supported that is BBB or BOT (Bulk Only Transport) and UAS
+ (USB Attached SCSI). BOT is advertised on alternative
+ interface 0 (primary) and UAS is on alternative interface 1.
+ Both protocols can work on USB2.0 and USB3.0.
+ UAS utilizes the USB 3.0 feature called streams support.
+
+choice
+ tristate "USB Gadget precomposed configurations"
+ default USB_ETH
+ optional
+ help
+ A Linux "Gadget Driver" talks to the USB Peripheral Controller
+ driver through the abstract "gadget" API. Some other operating
+ systems call these "client" drivers, of which "class drivers"
+ are a subset (implementing a USB device class specification).
+ A gadget driver implements one or more USB functions using
+ the peripheral hardware.
+
+ Gadget drivers are hardware-neutral, or "platform independent",
+ except that they sometimes must understand quirks or limitations
+ of the particular controllers they work with. For example, when
+ a controller doesn't support alternate configurations or provide
+ enough of the right types of endpoints, the gadget driver might
+ not be able work with that controller, or might need to implement
+ a less common variant of a device class protocol.
+
+ The available choices each represent a single precomposed USB
+ gadget configuration. In the device model, each option contains
+ both the device instantiation as a child for a USB gadget
+ controller, and the relevant drivers for each function declared
+ by the device.
+
+source "drivers/usb/gadget/legacy/Kconfig"
+
+endchoice
+
+endif # USB_GADGET