[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/drivers/usb/host/ohci-pxa27x.c b/src/kernel/linux/v4.14/drivers/usb/host/ohci-pxa27x.c
new file mode 100644
index 0000000..21c010f
--- /dev/null
+++ b/src/kernel/linux/v4.14/drivers/usb/host/ohci-pxa27x.c
@@ -0,0 +1,627 @@
+/*
+ * OHCI HCD (Host Controller Driver) for USB.
+ *
+ * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
+ * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
+ * (C) Copyright 2002 Hewlett-Packard Company
+ *
+ * Bus Glue for pxa27x
+ *
+ * Written by Christopher Hoover <ch@hpl.hp.com>
+ * Based on fragments of previous driver by Russell King et al.
+ *
+ * Modified for LH7A404 from ohci-sa1111.c
+ * by Durgesh Pattamatta <pattamattad@sharpsec.com>
+ *
+ * Modified for pxa27x from ohci-lh7a404.c
+ * by Nick Bane <nick@cecomputing.co.uk> 26-8-2004
+ *
+ * This file is licenced under the GPL.
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/usb-pxa3xx-ulpi.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/signal.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+#include <linux/usb/otg.h>
+
+#include <mach/hardware.h>
+
+#include "ohci.h"
+
+#define DRIVER_DESC "OHCI PXA27x/PXA3x driver"
+
+/*
+ * UHC: USB Host Controller (OHCI-like) register definitions
+ */
+#define UHCREV (0x0000) /* UHC HCI Spec Revision */
+#define UHCHCON (0x0004) /* UHC Host Control Register */
+#define UHCCOMS (0x0008) /* UHC Command Status Register */
+#define UHCINTS (0x000C) /* UHC Interrupt Status Register */
+#define UHCINTE (0x0010) /* UHC Interrupt Enable */
+#define UHCINTD (0x0014) /* UHC Interrupt Disable */
+#define UHCHCCA (0x0018) /* UHC Host Controller Comm. Area */
+#define UHCPCED (0x001C) /* UHC Period Current Endpt Descr */
+#define UHCCHED (0x0020) /* UHC Control Head Endpt Descr */
+#define UHCCCED (0x0024) /* UHC Control Current Endpt Descr */
+#define UHCBHED (0x0028) /* UHC Bulk Head Endpt Descr */
+#define UHCBCED (0x002C) /* UHC Bulk Current Endpt Descr */
+#define UHCDHEAD (0x0030) /* UHC Done Head */
+#define UHCFMI (0x0034) /* UHC Frame Interval */
+#define UHCFMR (0x0038) /* UHC Frame Remaining */
+#define UHCFMN (0x003C) /* UHC Frame Number */
+#define UHCPERS (0x0040) /* UHC Periodic Start */
+#define UHCLS (0x0044) /* UHC Low Speed Threshold */
+
+#define UHCRHDA (0x0048) /* UHC Root Hub Descriptor A */
+#define UHCRHDA_NOCP (1 << 12) /* No over current protection */
+#define UHCRHDA_OCPM (1 << 11) /* Over Current Protection Mode */
+#define UHCRHDA_POTPGT(x) \
+ (((x) & 0xff) << 24) /* Power On To Power Good Time */
+
+#define UHCRHDB (0x004C) /* UHC Root Hub Descriptor B */
+#define UHCRHS (0x0050) /* UHC Root Hub Status */
+#define UHCRHPS1 (0x0054) /* UHC Root Hub Port 1 Status */
+#define UHCRHPS2 (0x0058) /* UHC Root Hub Port 2 Status */
+#define UHCRHPS3 (0x005C) /* UHC Root Hub Port 3 Status */
+
+#define UHCSTAT (0x0060) /* UHC Status Register */
+#define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */
+#define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/
+#define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/
+#define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */
+#define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */
+#define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */
+#define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */
+#define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */
+#define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */
+
+#define UHCHR (0x0064) /* UHC Reset Register */
+#define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */
+#define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */
+#define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */
+#define UHCHR_PCPL (1 << 7) /* Power control polarity low */
+#define UHCHR_PSPL (1 << 6) /* Power sense polarity low */
+#define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */
+#define UHCHR_UIT (1 << 4) /* USB Interrupt Test */
+#define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */
+#define UHCHR_CGR (1 << 2) /* Clock Generation Reset */
+#define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */
+#define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */
+
+#define UHCHIE (0x0068) /* UHC Interrupt Enable Register*/
+#define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */
+#define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */
+#define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */
+#define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */
+#define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort
+ Interrupt Enable*/
+#define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */
+#define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */
+
+#define UHCHIT (0x006C) /* UHC Interrupt Test register */
+
+#define PXA_UHC_MAX_PORTNUM 3
+
+static const char hcd_name[] = "ohci-pxa27x";
+
+static struct hc_driver __read_mostly ohci_pxa27x_hc_driver;
+
+struct pxa27x_ohci {
+ struct clk *clk;
+ void __iomem *mmio_base;
+ struct regulator *vbus[3];
+ bool vbus_enabled[3];
+};
+
+#define to_pxa27x_ohci(hcd) (struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)
+
+/*
+ PMM_NPS_MODE -- PMM Non-power switching mode
+ Ports are powered continuously.
+
+ PMM_GLOBAL_MODE -- PMM global switching mode
+ All ports are powered at the same time.
+
+ PMM_PERPORT_MODE -- PMM per port switching mode
+ Ports are powered individually.
+ */
+static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *pxa_ohci, int mode)
+{
+ uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA);
+ uint32_t uhcrhdb = __raw_readl(pxa_ohci->mmio_base + UHCRHDB);
+
+ switch (mode) {
+ case PMM_NPS_MODE:
+ uhcrhda |= RH_A_NPS;
+ break;
+ case PMM_GLOBAL_MODE:
+ uhcrhda &= ~(RH_A_NPS & RH_A_PSM);
+ break;
+ case PMM_PERPORT_MODE:
+ uhcrhda &= ~(RH_A_NPS);
+ uhcrhda |= RH_A_PSM;
+
+ /* Set port power control mask bits, only 3 ports. */
+ uhcrhdb |= (0x7<<17);
+ break;
+ default:
+ printk( KERN_ERR
+ "Invalid mode %d, set to non-power switch mode.\n",
+ mode );
+
+ uhcrhda |= RH_A_NPS;
+ }
+
+ __raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA);
+ __raw_writel(uhcrhdb, pxa_ohci->mmio_base + UHCRHDB);
+ return 0;
+}
+
+static int pxa27x_ohci_set_vbus_power(struct pxa27x_ohci *pxa_ohci,
+ unsigned int port, bool enable)
+{
+ struct regulator *vbus = pxa_ohci->vbus[port];
+ int ret = 0;
+
+ if (IS_ERR_OR_NULL(vbus))
+ return 0;
+
+ if (enable && !pxa_ohci->vbus_enabled[port])
+ ret = regulator_enable(vbus);
+ else if (!enable && pxa_ohci->vbus_enabled[port])
+ ret = regulator_disable(vbus);
+
+ if (ret < 0)
+ return ret;
+
+ pxa_ohci->vbus_enabled[port] = enable;
+
+ return 0;
+}
+
+static int pxa27x_ohci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
+ u16 wIndex, char *buf, u16 wLength)
+{
+ struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
+ int ret;
+
+ switch (typeReq) {
+ case SetPortFeature:
+ case ClearPortFeature:
+ if (!wIndex || wIndex > 3)
+ return -EPIPE;
+
+ if (wValue != USB_PORT_FEAT_POWER)
+ break;
+
+ ret = pxa27x_ohci_set_vbus_power(pxa_ohci, wIndex - 1,
+ typeReq == SetPortFeature);
+ if (ret)
+ return ret;
+ break;
+ }
+
+ return ohci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength);
+}
+/*-------------------------------------------------------------------------*/
+
+static inline void pxa27x_setup_hc(struct pxa27x_ohci *pxa_ohci,
+ struct pxaohci_platform_data *inf)
+{
+ uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR);
+ uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA);
+
+ if (inf->flags & ENABLE_PORT1)
+ uhchr &= ~UHCHR_SSEP1;
+
+ if (inf->flags & ENABLE_PORT2)
+ uhchr &= ~UHCHR_SSEP2;
+
+ if (inf->flags & ENABLE_PORT3)
+ uhchr &= ~UHCHR_SSEP3;
+
+ if (inf->flags & POWER_CONTROL_LOW)
+ uhchr |= UHCHR_PCPL;
+
+ if (inf->flags & POWER_SENSE_LOW)
+ uhchr |= UHCHR_PSPL;
+
+ if (inf->flags & NO_OC_PROTECTION)
+ uhcrhda |= UHCRHDA_NOCP;
+ else
+ uhcrhda &= ~UHCRHDA_NOCP;
+
+ if (inf->flags & OC_MODE_PERPORT)
+ uhcrhda |= UHCRHDA_OCPM;
+ else
+ uhcrhda &= ~UHCRHDA_OCPM;
+
+ if (inf->power_on_delay) {
+ uhcrhda &= ~UHCRHDA_POTPGT(0xff);
+ uhcrhda |= UHCRHDA_POTPGT(inf->power_on_delay / 2);
+ }
+
+ __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
+ __raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA);
+}
+
+static inline void pxa27x_reset_hc(struct pxa27x_ohci *pxa_ohci)
+{
+ uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR);
+
+ __raw_writel(uhchr | UHCHR_FHR, pxa_ohci->mmio_base + UHCHR);
+ udelay(11);
+ __raw_writel(uhchr & ~UHCHR_FHR, pxa_ohci->mmio_base + UHCHR);
+}
+
+#ifdef CONFIG_PXA27x
+extern void pxa27x_clear_otgph(void);
+#else
+#define pxa27x_clear_otgph() do {} while (0)
+#endif
+
+static int pxa27x_start_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev)
+{
+ int retval;
+ struct pxaohci_platform_data *inf;
+ uint32_t uhchr;
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
+
+ inf = dev_get_platdata(dev);
+
+ retval = clk_prepare_enable(pxa_ohci->clk);
+ if (retval)
+ return retval;
+
+ pxa27x_reset_hc(pxa_ohci);
+
+ uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) | UHCHR_FSBIR;
+ __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
+
+ while (__raw_readl(pxa_ohci->mmio_base + UHCHR) & UHCHR_FSBIR)
+ cpu_relax();
+
+ pxa27x_setup_hc(pxa_ohci, inf);
+
+ if (inf->init)
+ retval = inf->init(dev);
+
+ if (retval < 0) {
+ clk_disable_unprepare(pxa_ohci->clk);
+ return retval;
+ }
+
+ if (cpu_is_pxa3xx())
+ pxa3xx_u2d_start_hc(&hcd->self);
+
+ uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
+ __raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
+ __raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, pxa_ohci->mmio_base + UHCHIE);
+
+ /* Clear any OTG Pin Hold */
+ pxa27x_clear_otgph();
+ return 0;
+}
+
+static void pxa27x_stop_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev)
+{
+ struct pxaohci_platform_data *inf;
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
+ uint32_t uhccoms;
+
+ inf = dev_get_platdata(dev);
+
+ if (cpu_is_pxa3xx())
+ pxa3xx_u2d_stop_hc(&hcd->self);
+
+ if (inf->exit)
+ inf->exit(dev);
+
+ pxa27x_reset_hc(pxa_ohci);
+
+ /* Host Controller Reset */
+ uhccoms = __raw_readl(pxa_ohci->mmio_base + UHCCOMS) | 0x01;
+ __raw_writel(uhccoms, pxa_ohci->mmio_base + UHCCOMS);
+ udelay(10);
+
+ clk_disable_unprepare(pxa_ohci->clk);
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id pxa_ohci_dt_ids[] = {
+ { .compatible = "marvell,pxa-ohci" },
+ { }
+};
+
+MODULE_DEVICE_TABLE(of, pxa_ohci_dt_ids);
+
+static int ohci_pxa_of_init(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct pxaohci_platform_data *pdata;
+ u32 tmp;
+ int ret;
+
+ if (!np)
+ return 0;
+
+ /* Right now device-tree probed devices don't get dma_mask set.
+ * Since shared usb code relies on it, set it here for now.
+ * Once we have dma capability bindings this can go away.
+ */
+ ret = dma_coerce_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
+ if (ret)
+ return ret;
+
+ pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return -ENOMEM;
+
+ if (of_property_read_bool(np, "marvell,enable-port1"))
+ pdata->flags |= ENABLE_PORT1;
+ if (of_property_read_bool(np, "marvell,enable-port2"))
+ pdata->flags |= ENABLE_PORT2;
+ if (of_property_read_bool(np, "marvell,enable-port3"))
+ pdata->flags |= ENABLE_PORT3;
+ if (of_property_read_bool(np, "marvell,port-sense-low"))
+ pdata->flags |= POWER_SENSE_LOW;
+ if (of_property_read_bool(np, "marvell,power-control-low"))
+ pdata->flags |= POWER_CONTROL_LOW;
+ if (of_property_read_bool(np, "marvell,no-oc-protection"))
+ pdata->flags |= NO_OC_PROTECTION;
+ if (of_property_read_bool(np, "marvell,oc-mode-perport"))
+ pdata->flags |= OC_MODE_PERPORT;
+ if (!of_property_read_u32(np, "marvell,power-on-delay", &tmp))
+ pdata->power_on_delay = tmp;
+ if (!of_property_read_u32(np, "marvell,port-mode", &tmp))
+ pdata->port_mode = tmp;
+ if (!of_property_read_u32(np, "marvell,power-budget", &tmp))
+ pdata->power_budget = tmp;
+
+ pdev->dev.platform_data = pdata;
+
+ return 0;
+}
+#else
+static int ohci_pxa_of_init(struct platform_device *pdev)
+{
+ return 0;
+}
+#endif
+
+/*-------------------------------------------------------------------------*/
+
+/* configure so an HC device and id are always provided */
+/* always called with process context; sleeping is OK */
+
+
+/**
+ * ohci_hcd_pxa27x_probe - initialize pxa27x-based HCDs
+ * Context: !in_interrupt()
+ *
+ * Allocates basic resources for this USB host controller, and
+ * then invokes the start() method for the HCD associated with it
+ * through the hotplug entry's driver_data.
+ *
+ */
+static int ohci_hcd_pxa27x_probe(struct platform_device *pdev)
+{
+ int retval, irq;
+ struct usb_hcd *hcd;
+ struct pxaohci_platform_data *inf;
+ struct pxa27x_ohci *pxa_ohci;
+ struct ohci_hcd *ohci;
+ struct resource *r;
+ struct clk *usb_clk;
+ unsigned int i;
+
+ retval = ohci_pxa_of_init(pdev);
+ if (retval)
+ return retval;
+
+ inf = dev_get_platdata(&pdev->dev);
+
+ if (!inf)
+ return -ENODEV;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ pr_err("no resource of IORESOURCE_IRQ");
+ return irq;
+ }
+
+ usb_clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(usb_clk))
+ return PTR_ERR(usb_clk);
+
+ hcd = usb_create_hcd(&ohci_pxa27x_hc_driver, &pdev->dev, "pxa27x");
+ if (!hcd)
+ return -ENOMEM;
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ hcd->regs = devm_ioremap_resource(&pdev->dev, r);
+ if (IS_ERR(hcd->regs)) {
+ retval = PTR_ERR(hcd->regs);
+ goto err;
+ }
+ hcd->rsrc_start = r->start;
+ hcd->rsrc_len = resource_size(r);
+
+ /* initialize "struct pxa27x_ohci" */
+ pxa_ohci = to_pxa27x_ohci(hcd);
+ pxa_ohci->clk = usb_clk;
+ pxa_ohci->mmio_base = (void __iomem *)hcd->regs;
+
+ for (i = 0; i < 3; ++i) {
+ char name[6];
+
+ if (!(inf->flags & (ENABLE_PORT1 << i)))
+ continue;
+
+ sprintf(name, "vbus%u", i + 1);
+ pxa_ohci->vbus[i] = devm_regulator_get(&pdev->dev, name);
+ }
+
+ retval = pxa27x_start_hc(pxa_ohci, &pdev->dev);
+ if (retval < 0) {
+ pr_debug("pxa27x_start_hc failed");
+ goto err;
+ }
+
+ /* Select Power Management Mode */
+ pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode);
+
+ if (inf->power_budget)
+ hcd->power_budget = inf->power_budget;
+
+ /* The value of NDP in roothub_a is incorrect on this hardware */
+ ohci = hcd_to_ohci(hcd);
+ ohci->num_ports = 3;
+
+ retval = usb_add_hcd(hcd, irq, 0);
+ if (retval == 0) {
+ device_wakeup_enable(hcd->self.controller);
+ return retval;
+ }
+
+ pxa27x_stop_hc(pxa_ohci, &pdev->dev);
+ err:
+ usb_put_hcd(hcd);
+ return retval;
+}
+
+
+/* may be called without controller electrically present */
+/* may be called with controller, bus, and devices active */
+
+/**
+ * ohci_hcd_pxa27x_remove - shutdown processing for pxa27x-based HCDs
+ * @dev: USB Host Controller being removed
+ * Context: !in_interrupt()
+ *
+ * Reverses the effect of ohci_hcd_pxa27x_probe(), first invoking
+ * the HCD's stop() method. It is always called from a thread
+ * context, normally "rmmod", "apmd", or something similar.
+ *
+ */
+static int ohci_hcd_pxa27x_remove(struct platform_device *pdev)
+{
+ struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
+ unsigned int i;
+
+ usb_remove_hcd(hcd);
+ pxa27x_stop_hc(pxa_ohci, &pdev->dev);
+
+ for (i = 0; i < 3; ++i)
+ pxa27x_ohci_set_vbus_power(pxa_ohci, i, false);
+
+ usb_put_hcd(hcd);
+ return 0;
+}
+
+/*-------------------------------------------------------------------------*/
+
+#ifdef CONFIG_PM
+static int ohci_hcd_pxa27x_drv_suspend(struct device *dev)
+{
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
+ struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
+ struct ohci_hcd *ohci = hcd_to_ohci(hcd);
+ bool do_wakeup = device_may_wakeup(dev);
+ int ret;
+
+
+ if (time_before(jiffies, ohci->next_statechange))
+ msleep(5);
+ ohci->next_statechange = jiffies;
+
+ ret = ohci_suspend(hcd, do_wakeup);
+ if (ret)
+ return ret;
+
+ pxa27x_stop_hc(pxa_ohci, dev);
+ return ret;
+}
+
+static int ohci_hcd_pxa27x_drv_resume(struct device *dev)
+{
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
+ struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
+ struct pxaohci_platform_data *inf = dev_get_platdata(dev);
+ struct ohci_hcd *ohci = hcd_to_ohci(hcd);
+ int status;
+
+ if (time_before(jiffies, ohci->next_statechange))
+ msleep(5);
+ ohci->next_statechange = jiffies;
+
+ status = pxa27x_start_hc(pxa_ohci, dev);
+ if (status < 0)
+ return status;
+
+ /* Select Power Management Mode */
+ pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode);
+
+ ohci_resume(hcd, false);
+ return 0;
+}
+
+static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = {
+ .suspend = ohci_hcd_pxa27x_drv_suspend,
+ .resume = ohci_hcd_pxa27x_drv_resume,
+};
+#endif
+
+static struct platform_driver ohci_hcd_pxa27x_driver = {
+ .probe = ohci_hcd_pxa27x_probe,
+ .remove = ohci_hcd_pxa27x_remove,
+ .shutdown = usb_hcd_platform_shutdown,
+ .driver = {
+ .name = "pxa27x-ohci",
+ .of_match_table = of_match_ptr(pxa_ohci_dt_ids),
+#ifdef CONFIG_PM
+ .pm = &ohci_hcd_pxa27x_pm_ops,
+#endif
+ },
+};
+
+static const struct ohci_driver_overrides pxa27x_overrides __initconst = {
+ .extra_priv_size = sizeof(struct pxa27x_ohci),
+};
+
+static int __init ohci_pxa27x_init(void)
+{
+ if (usb_disabled())
+ return -ENODEV;
+
+ pr_info("%s: " DRIVER_DESC "\n", hcd_name);
+
+ ohci_init_driver(&ohci_pxa27x_hc_driver, &pxa27x_overrides);
+ ohci_pxa27x_hc_driver.hub_control = pxa27x_ohci_hub_control;
+
+ return platform_driver_register(&ohci_hcd_pxa27x_driver);
+}
+module_init(ohci_pxa27x_init);
+
+static void __exit ohci_pxa27x_cleanup(void)
+{
+ platform_driver_unregister(&ohci_hcd_pxa27x_driver);
+}
+module_exit(ohci_pxa27x_cleanup);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:pxa27x-ohci");