[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/drivers/watchdog/aspeed_wdt.c b/src/kernel/linux/v4.14/drivers/watchdog/aspeed_wdt.c
new file mode 100644
index 0000000..f5835cb
--- /dev/null
+++ b/src/kernel/linux/v4.14/drivers/watchdog/aspeed_wdt.c
@@ -0,0 +1,331 @@
+/*
+ * Copyright 2016 IBM Corporation
+ *
+ * Joel Stanley <joel@jms.id.au>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/watchdog.h>
+
+struct aspeed_wdt {
+ struct watchdog_device wdd;
+ void __iomem *base;
+ u32 ctrl;
+};
+
+struct aspeed_wdt_config {
+ u32 ext_pulse_width_mask;
+};
+
+static const struct aspeed_wdt_config ast2400_config = {
+ .ext_pulse_width_mask = 0xff,
+};
+
+static const struct aspeed_wdt_config ast2500_config = {
+ .ext_pulse_width_mask = 0xfffff,
+};
+
+static const struct of_device_id aspeed_wdt_of_table[] = {
+ { .compatible = "aspeed,ast2400-wdt", .data = &ast2400_config },
+ { .compatible = "aspeed,ast2500-wdt", .data = &ast2500_config },
+ { .compatible = "aspeed,ast2600-wdt", .data = &ast2500_config },
+ { },
+};
+MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table);
+
+#define WDT_STATUS 0x00
+#define WDT_RELOAD_VALUE 0x04
+#define WDT_RESTART 0x08
+#define WDT_CTRL 0x0C
+#define WDT_CTRL_BOOT_SECONDARY BIT(7)
+#define WDT_CTRL_RESET_MODE_SOC (0x00 << 5)
+#define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5)
+#define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5)
+#define WDT_CTRL_1MHZ_CLK BIT(4)
+#define WDT_CTRL_WDT_EXT BIT(3)
+#define WDT_CTRL_WDT_INTR BIT(2)
+#define WDT_CTRL_RESET_SYSTEM BIT(1)
+#define WDT_CTRL_ENABLE BIT(0)
+
+/*
+ * WDT_RESET_WIDTH controls the characteristics of the external pulse (if
+ * enabled), specifically:
+ *
+ * * Pulse duration
+ * * Drive mode: push-pull vs open-drain
+ * * Polarity: Active high or active low
+ *
+ * Pulse duration configuration is available on both the AST2400 and AST2500,
+ * though the field changes between SoCs:
+ *
+ * AST2400: Bits 7:0
+ * AST2500: Bits 19:0
+ *
+ * This difference is captured in struct aspeed_wdt_config.
+ *
+ * The AST2500 exposes the drive mode and polarity options, but not in a
+ * regular fashion. For read purposes, bit 31 represents active high or low,
+ * and bit 30 represents push-pull or open-drain. With respect to write, magic
+ * values need to be written to the top byte to change the state of the drive
+ * mode and polarity bits. Any other value written to the top byte has no
+ * effect on the state of the drive mode or polarity bits. However, the pulse
+ * width value must be preserved (as desired) if written.
+ */
+#define WDT_RESET_WIDTH 0x18
+#define WDT_RESET_WIDTH_ACTIVE_HIGH BIT(31)
+#define WDT_ACTIVE_HIGH_MAGIC (0xA5 << 24)
+#define WDT_ACTIVE_LOW_MAGIC (0x5A << 24)
+#define WDT_RESET_WIDTH_PUSH_PULL BIT(30)
+#define WDT_PUSH_PULL_MAGIC (0xA8 << 24)
+#define WDT_OPEN_DRAIN_MAGIC (0x8A << 24)
+
+#define WDT_RESTART_MAGIC 0x4755
+
+/* 32 bits at 1MHz, in milliseconds */
+#define WDT_MAX_TIMEOUT_MS 4294967
+#define WDT_DEFAULT_TIMEOUT 30
+#define WDT_RATE_1MHZ 1000000
+
+static struct aspeed_wdt *to_aspeed_wdt(struct watchdog_device *wdd)
+{
+ return container_of(wdd, struct aspeed_wdt, wdd);
+}
+
+static void aspeed_wdt_enable(struct aspeed_wdt *wdt, int count)
+{
+ wdt->ctrl |= WDT_CTRL_ENABLE;
+
+ writel(0, wdt->base + WDT_CTRL);
+ writel(count, wdt->base + WDT_RELOAD_VALUE);
+ writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART);
+ writel(wdt->ctrl, wdt->base + WDT_CTRL);
+}
+
+static int aspeed_wdt_start(struct watchdog_device *wdd)
+{
+ struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
+
+ aspeed_wdt_enable(wdt, wdd->timeout * WDT_RATE_1MHZ);
+
+ return 0;
+}
+
+static int aspeed_wdt_stop(struct watchdog_device *wdd)
+{
+ struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
+
+ wdt->ctrl &= ~WDT_CTRL_ENABLE;
+ writel(wdt->ctrl, wdt->base + WDT_CTRL);
+
+ return 0;
+}
+
+static int aspeed_wdt_ping(struct watchdog_device *wdd)
+{
+ struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
+
+ writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART);
+
+ return 0;
+}
+
+static int aspeed_wdt_set_timeout(struct watchdog_device *wdd,
+ unsigned int timeout)
+{
+ struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
+ u32 actual;
+
+ wdd->timeout = timeout;
+
+ actual = min(timeout, wdd->max_hw_heartbeat_ms * 1000);
+
+ writel(actual * WDT_RATE_1MHZ, wdt->base + WDT_RELOAD_VALUE);
+ writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART);
+
+ return 0;
+}
+
+static int aspeed_wdt_restart(struct watchdog_device *wdd,
+ unsigned long action, void *data)
+{
+ struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
+
+ wdt->ctrl &= ~WDT_CTRL_BOOT_SECONDARY;
+ aspeed_wdt_enable(wdt, 128 * WDT_RATE_1MHZ / 1000);
+
+ mdelay(1000);
+
+ return 0;
+}
+
+static const struct watchdog_ops aspeed_wdt_ops = {
+ .start = aspeed_wdt_start,
+ .stop = aspeed_wdt_stop,
+ .ping = aspeed_wdt_ping,
+ .set_timeout = aspeed_wdt_set_timeout,
+ .restart = aspeed_wdt_restart,
+ .owner = THIS_MODULE,
+};
+
+static const struct watchdog_info aspeed_wdt_info = {
+ .options = WDIOF_KEEPALIVEPING
+ | WDIOF_MAGICCLOSE
+ | WDIOF_SETTIMEOUT,
+ .identity = KBUILD_MODNAME,
+};
+
+static int aspeed_wdt_probe(struct platform_device *pdev)
+{
+ const struct aspeed_wdt_config *config;
+ const struct of_device_id *ofdid;
+ struct aspeed_wdt *wdt;
+ struct resource *res;
+ struct device_node *np;
+ const char *reset_type;
+ u32 duration;
+ int ret;
+
+ wdt = devm_kzalloc(&pdev->dev, sizeof(*wdt), GFP_KERNEL);
+ if (!wdt)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ wdt->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(wdt->base))
+ return PTR_ERR(wdt->base);
+
+ wdt->wdd.info = &aspeed_wdt_info;
+ wdt->wdd.ops = &aspeed_wdt_ops;
+ wdt->wdd.max_hw_heartbeat_ms = WDT_MAX_TIMEOUT_MS;
+ wdt->wdd.parent = &pdev->dev;
+
+ wdt->wdd.timeout = WDT_DEFAULT_TIMEOUT;
+ watchdog_init_timeout(&wdt->wdd, 0, &pdev->dev);
+
+ np = pdev->dev.of_node;
+
+ ofdid = of_match_node(aspeed_wdt_of_table, np);
+ if (!ofdid)
+ return -EINVAL;
+ config = ofdid->data;
+
+ /*
+ * On clock rates:
+ * - ast2400 wdt can run at PCLK, or 1MHz
+ * - ast2500 only runs at 1MHz, hard coding bit 4 to 1
+ * - ast2600 always runs at 1MHz
+ *
+ * Set the ast2400 to run at 1MHz as it simplifies the driver.
+ */
+ if (of_device_is_compatible(np, "aspeed,ast2400-wdt"))
+ wdt->ctrl = WDT_CTRL_1MHZ_CLK;
+
+ /*
+ * Control reset on a per-device basis to ensure the
+ * host is not affected by a BMC reboot
+ */
+ ret = of_property_read_string(np, "aspeed,reset-type", &reset_type);
+ if (ret) {
+ wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC | WDT_CTRL_RESET_SYSTEM;
+ } else {
+ if (!strcmp(reset_type, "cpu"))
+ wdt->ctrl |= WDT_CTRL_RESET_MODE_ARM_CPU |
+ WDT_CTRL_RESET_SYSTEM;
+ else if (!strcmp(reset_type, "soc"))
+ wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC |
+ WDT_CTRL_RESET_SYSTEM;
+ else if (!strcmp(reset_type, "system"))
+ wdt->ctrl |= WDT_CTRL_RESET_MODE_FULL_CHIP |
+ WDT_CTRL_RESET_SYSTEM;
+ else if (strcmp(reset_type, "none"))
+ return -EINVAL;
+ }
+ if (of_property_read_bool(np, "aspeed,external-signal"))
+ wdt->ctrl |= WDT_CTRL_WDT_EXT;
+ if (of_property_read_bool(np, "aspeed,alt-boot"))
+ wdt->ctrl |= WDT_CTRL_BOOT_SECONDARY;
+
+ writel(wdt->ctrl, wdt->base + WDT_CTRL);
+
+ if (readl(wdt->base + WDT_CTRL) & WDT_CTRL_ENABLE) {
+ aspeed_wdt_start(&wdt->wdd);
+ set_bit(WDOG_HW_RUNNING, &wdt->wdd.status);
+ }
+
+ if ((of_device_is_compatible(np, "aspeed,ast2500-wdt")) ||
+ (of_device_is_compatible(np, "aspeed,ast2600-wdt"))) {
+ u32 reg = readl(wdt->base + WDT_RESET_WIDTH);
+
+ reg &= config->ext_pulse_width_mask;
+ if (of_property_read_bool(np, "aspeed,ext-push-pull"))
+ reg |= WDT_PUSH_PULL_MAGIC;
+ else
+ reg |= WDT_OPEN_DRAIN_MAGIC;
+
+ writel(reg, wdt->base + WDT_RESET_WIDTH);
+
+ reg &= config->ext_pulse_width_mask;
+ if (of_property_read_bool(np, "aspeed,ext-active-high"))
+ reg |= WDT_ACTIVE_HIGH_MAGIC;
+ else
+ reg |= WDT_ACTIVE_LOW_MAGIC;
+
+ writel(reg, wdt->base + WDT_RESET_WIDTH);
+ }
+
+ if (!of_property_read_u32(np, "aspeed,ext-pulse-duration", &duration)) {
+ u32 max_duration = config->ext_pulse_width_mask + 1;
+
+ if (duration == 0 || duration > max_duration) {
+ dev_err(&pdev->dev, "Invalid pulse duration: %uus\n",
+ duration);
+ duration = max(1U, min(max_duration, duration));
+ dev_info(&pdev->dev, "Pulse duration set to %uus\n",
+ duration);
+ }
+
+ /*
+ * The watchdog is always configured with a 1MHz source, so
+ * there is no need to scale the microsecond value. However we
+ * need to offset it - from the datasheet:
+ *
+ * "This register decides the asserting duration of wdt_ext and
+ * wdt_rstarm signal. The default value is 0xFF. It means the
+ * default asserting duration of wdt_ext and wdt_rstarm is
+ * 256us."
+ *
+ * This implies a value of 0 gives a 1us pulse.
+ */
+ writel(duration - 1, wdt->base + WDT_RESET_WIDTH);
+ }
+
+ ret = devm_watchdog_register_device(&pdev->dev, &wdt->wdd);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static struct platform_driver aspeed_watchdog_driver = {
+ .probe = aspeed_wdt_probe,
+ .driver = {
+ .name = KBUILD_MODNAME,
+ .of_match_table = of_match_ptr(aspeed_wdt_of_table),
+ },
+};
+module_platform_driver(aspeed_watchdog_driver);
+
+MODULE_DESCRIPTION("Aspeed Watchdog Driver");
+MODULE_LICENSE("GPL");