[Feature]add MT2731_MP2_MR2_SVN388 baseline version
Change-Id: Ief04314834b31e27effab435d3ca8ba33b499059
diff --git a/src/kernel/linux/v4.14/lib/842/842.h b/src/kernel/linux/v4.14/lib/842/842.h
new file mode 100644
index 0000000..7b1f581
--- /dev/null
+++ b/src/kernel/linux/v4.14/lib/842/842.h
@@ -0,0 +1,130 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef __842_H__
+#define __842_H__
+
+/* The 842 compressed format is made up of multiple blocks, each of
+ * which have the format:
+ *
+ * <template>[arg1][arg2][arg3][arg4]
+ *
+ * where there are between 0 and 4 template args, depending on the specific
+ * template operation. For normal operations, each arg is either a specific
+ * number of data bytes to add to the output buffer, or an index pointing
+ * to a previously-written number of data bytes to copy to the output buffer.
+ *
+ * The template code is a 5-bit value. This code indicates what to do with
+ * the following data. Template codes from 0 to 0x19 should use the template
+ * table, the static "decomp_ops" table used in decompress. For each template
+ * (table row), there are between 1 and 4 actions; each action corresponds to
+ * an arg following the template code bits. Each action is either a "data"
+ * type action, or a "index" type action, and each action results in 2, 4, or 8
+ * bytes being written to the output buffer. Each template (i.e. all actions
+ * in the table row) will add up to 8 bytes being written to the output buffer.
+ * Any row with less than 4 actions is padded with noop actions, indicated by
+ * N0 (for which there is no corresponding arg in the compressed data buffer).
+ *
+ * "Data" actions, indicated in the table by D2, D4, and D8, mean that the
+ * corresponding arg is 2, 4, or 8 bytes, respectively, in the compressed data
+ * buffer should be copied directly to the output buffer.
+ *
+ * "Index" actions, indicated in the table by I2, I4, and I8, mean the
+ * corresponding arg is an index parameter that points to, respectively, a 2,
+ * 4, or 8 byte value already in the output buffer, that should be copied to
+ * the end of the output buffer. Essentially, the index points to a position
+ * in a ring buffer that contains the last N bytes of output buffer data.
+ * The number of bits for each index's arg are: 8 bits for I2, 9 bits for I4,
+ * and 8 bits for I8. Since each index points to a 2, 4, or 8 byte section,
+ * this means that I2 can reference 512 bytes ((2^8 bits = 256) * 2 bytes), I4
+ * can reference 2048 bytes ((2^9 = 512) * 4 bytes), and I8 can reference 2048
+ * bytes ((2^8 = 256) * 8 bytes). Think of it as a kind-of ring buffer for
+ * each of I2, I4, and I8 that are updated for each byte written to the output
+ * buffer. In this implementation, the output buffer is directly used for each
+ * index; there is no additional memory required. Note that the index is into
+ * a ring buffer, not a sliding window; for example, if there have been 260
+ * bytes written to the output buffer, an I2 index of 0 would index to byte 256
+ * in the output buffer, while an I2 index of 16 would index to byte 16 in the
+ * output buffer.
+ *
+ * There are also 3 special template codes; 0x1b for "repeat", 0x1c for
+ * "zeros", and 0x1e for "end". The "repeat" operation is followed by a 6 bit
+ * arg N indicating how many times to repeat. The last 8 bytes written to the
+ * output buffer are written again to the output buffer, N + 1 times. The
+ * "zeros" operation, which has no arg bits, writes 8 zeros to the output
+ * buffer. The "end" operation, which also has no arg bits, signals the end
+ * of the compressed data. There may be some number of padding (don't care,
+ * but usually 0) bits after the "end" operation bits, to fill the buffer
+ * length to a specific byte multiple (usually a multiple of 8, 16, or 32
+ * bytes).
+ *
+ * This software implementation also uses one of the undefined template values,
+ * 0x1d as a special "short data" template code, to represent less than 8 bytes
+ * of uncompressed data. It is followed by a 3 bit arg N indicating how many
+ * data bytes will follow, and then N bytes of data, which should be copied to
+ * the output buffer. This allows the software 842 compressor to accept input
+ * buffers that are not an exact multiple of 8 bytes long. However, those
+ * compressed buffers containing this sw-only template will be rejected by
+ * the 842 hardware decompressor, and must be decompressed with this software
+ * library. The 842 software compression module includes a parameter to
+ * disable using this sw-only "short data" template, and instead simply
+ * reject any input buffer that is not a multiple of 8 bytes long.
+ *
+ * After all actions for each operation code are processed, another template
+ * code is in the next 5 bits. The decompression ends once the "end" template
+ * code is detected.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+#include <linux/crc32.h>
+#include <asm/unaligned.h>
+
+#include <linux/sw842.h>
+
+/* special templates */
+#define OP_REPEAT (0x1B)
+#define OP_ZEROS (0x1C)
+#define OP_END (0x1E)
+
+/* sw only template - this is not in the hw design; it's used only by this
+ * software compressor and decompressor, to allow input buffers that aren't
+ * a multiple of 8.
+ */
+#define OP_SHORT_DATA (0x1D)
+
+/* additional bits of each op param */
+#define OP_BITS (5)
+#define REPEAT_BITS (6)
+#define SHORT_DATA_BITS (3)
+#define I2_BITS (8)
+#define I4_BITS (9)
+#define I8_BITS (8)
+#define CRC_BITS (32)
+
+#define REPEAT_BITS_MAX (0x3f)
+#define SHORT_DATA_BITS_MAX (0x7)
+
+/* Arbitrary values used to indicate action */
+#define OP_ACTION (0x70)
+#define OP_ACTION_INDEX (0x10)
+#define OP_ACTION_DATA (0x20)
+#define OP_ACTION_NOOP (0x40)
+#define OP_AMOUNT (0x0f)
+#define OP_AMOUNT_0 (0x00)
+#define OP_AMOUNT_2 (0x02)
+#define OP_AMOUNT_4 (0x04)
+#define OP_AMOUNT_8 (0x08)
+
+#define D2 (OP_ACTION_DATA | OP_AMOUNT_2)
+#define D4 (OP_ACTION_DATA | OP_AMOUNT_4)
+#define D8 (OP_ACTION_DATA | OP_AMOUNT_8)
+#define I2 (OP_ACTION_INDEX | OP_AMOUNT_2)
+#define I4 (OP_ACTION_INDEX | OP_AMOUNT_4)
+#define I8 (OP_ACTION_INDEX | OP_AMOUNT_8)
+#define N0 (OP_ACTION_NOOP | OP_AMOUNT_0)
+
+/* the max of the regular templates - not including the special templates */
+#define OPS_MAX (0x1a)
+
+#endif