rjw | 1f88458 | 2022-01-06 17:20:42 +0800 | [diff] [blame^] | 1 | PCI TEST |
| 2 | Kishon Vijay Abraham I <kishon@ti.com> |
| 3 | |
| 4 | Traditionally PCI RC has always been validated by using standard |
| 5 | PCI cards like ethernet PCI cards or USB PCI cards or SATA PCI cards. |
| 6 | However with the addition of EP-core in linux kernel, it is possible |
| 7 | to configure a PCI controller that can operate in EP mode to work as |
| 8 | a test device. |
| 9 | |
| 10 | The PCI endpoint test device is a virtual device (defined in software) |
| 11 | used to test the endpoint functionality and serve as a sample driver |
| 12 | for other PCI endpoint devices (to use the EP framework). |
| 13 | |
| 14 | The PCI endpoint test device has the following registers: |
| 15 | |
| 16 | 1) PCI_ENDPOINT_TEST_MAGIC |
| 17 | 2) PCI_ENDPOINT_TEST_COMMAND |
| 18 | 3) PCI_ENDPOINT_TEST_STATUS |
| 19 | 4) PCI_ENDPOINT_TEST_SRC_ADDR |
| 20 | 5) PCI_ENDPOINT_TEST_DST_ADDR |
| 21 | 6) PCI_ENDPOINT_TEST_SIZE |
| 22 | 7) PCI_ENDPOINT_TEST_CHECKSUM |
| 23 | |
| 24 | *) PCI_ENDPOINT_TEST_MAGIC |
| 25 | |
| 26 | This register will be used to test BAR0. A known pattern will be written |
| 27 | and read back from MAGIC register to verify BAR0. |
| 28 | |
| 29 | *) PCI_ENDPOINT_TEST_COMMAND: |
| 30 | |
| 31 | This register will be used by the host driver to indicate the function |
| 32 | that the endpoint device must perform. |
| 33 | |
| 34 | Bitfield Description: |
| 35 | Bit 0 : raise legacy IRQ |
| 36 | Bit 1 : raise MSI IRQ |
| 37 | Bit 2 - 7 : MSI interrupt number |
| 38 | Bit 8 : read command (read data from RC buffer) |
| 39 | Bit 9 : write command (write data to RC buffer) |
| 40 | Bit 10 : copy command (copy data from one RC buffer to another |
| 41 | RC buffer) |
| 42 | |
| 43 | *) PCI_ENDPOINT_TEST_STATUS |
| 44 | |
| 45 | This register reflects the status of the PCI endpoint device. |
| 46 | |
| 47 | Bitfield Description: |
| 48 | Bit 0 : read success |
| 49 | Bit 1 : read fail |
| 50 | Bit 2 : write success |
| 51 | Bit 3 : write fail |
| 52 | Bit 4 : copy success |
| 53 | Bit 5 : copy fail |
| 54 | Bit 6 : IRQ raised |
| 55 | Bit 7 : source address is invalid |
| 56 | Bit 8 : destination address is invalid |
| 57 | |
| 58 | *) PCI_ENDPOINT_TEST_SRC_ADDR |
| 59 | |
| 60 | This register contains the source address (RC buffer address) for the |
| 61 | COPY/READ command. |
| 62 | |
| 63 | *) PCI_ENDPOINT_TEST_DST_ADDR |
| 64 | |
| 65 | This register contains the destination address (RC buffer address) for |
| 66 | the COPY/WRITE command. |