rjw | 1f88458 | 2022-01-06 17:20:42 +0800 | [diff] [blame^] | 1 | /* |
| 2 | * I2C Link Layer for ST NCI NFC controller familly based Driver |
| 3 | * Copyright (C) 2014-2015 STMicroelectronics SAS. All rights reserved. |
| 4 | * |
| 5 | * This program is free software; you can redistribute it and/or modify it |
| 6 | * under the terms and conditions of the GNU General Public License, |
| 7 | * version 2, as published by the Free Software Foundation. |
| 8 | * |
| 9 | * This program is distributed in the hope that it will be useful, |
| 10 | * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| 11 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| 12 | * GNU General Public License for more details. |
| 13 | * |
| 14 | * You should have received a copy of the GNU General Public License |
| 15 | * along with this program; if not, see <http://www.gnu.org/licenses/>. |
| 16 | */ |
| 17 | |
| 18 | #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt |
| 19 | |
| 20 | #include <linux/module.h> |
| 21 | #include <linux/i2c.h> |
| 22 | #include <linux/gpio/consumer.h> |
| 23 | #include <linux/acpi.h> |
| 24 | #include <linux/interrupt.h> |
| 25 | #include <linux/delay.h> |
| 26 | #include <linux/nfc.h> |
| 27 | #include <linux/of.h> |
| 28 | |
| 29 | #include "st-nci.h" |
| 30 | |
| 31 | #define DRIVER_DESC "NCI NFC driver for ST_NCI" |
| 32 | |
| 33 | /* ndlc header */ |
| 34 | #define ST_NCI_FRAME_HEADROOM 1 |
| 35 | #define ST_NCI_FRAME_TAILROOM 0 |
| 36 | |
| 37 | #define ST_NCI_I2C_MIN_SIZE 4 /* PCB(1) + NCI Packet header(3) */ |
| 38 | #define ST_NCI_I2C_MAX_SIZE 250 /* req 4.2.1 */ |
| 39 | |
| 40 | #define ST_NCI_DRIVER_NAME "st_nci" |
| 41 | #define ST_NCI_I2C_DRIVER_NAME "st_nci_i2c" |
| 42 | |
| 43 | struct st_nci_i2c_phy { |
| 44 | struct i2c_client *i2c_dev; |
| 45 | struct llt_ndlc *ndlc; |
| 46 | |
| 47 | bool irq_active; |
| 48 | |
| 49 | struct gpio_desc *gpiod_reset; |
| 50 | |
| 51 | struct st_nci_se_status se_status; |
| 52 | }; |
| 53 | |
| 54 | static int st_nci_i2c_enable(void *phy_id) |
| 55 | { |
| 56 | struct st_nci_i2c_phy *phy = phy_id; |
| 57 | |
| 58 | gpiod_set_value(phy->gpiod_reset, 0); |
| 59 | usleep_range(10000, 15000); |
| 60 | gpiod_set_value(phy->gpiod_reset, 1); |
| 61 | usleep_range(80000, 85000); |
| 62 | |
| 63 | if (phy->ndlc->powered == 0 && phy->irq_active == 0) { |
| 64 | enable_irq(phy->i2c_dev->irq); |
| 65 | phy->irq_active = true; |
| 66 | } |
| 67 | |
| 68 | return 0; |
| 69 | } |
| 70 | |
| 71 | static void st_nci_i2c_disable(void *phy_id) |
| 72 | { |
| 73 | struct st_nci_i2c_phy *phy = phy_id; |
| 74 | |
| 75 | disable_irq_nosync(phy->i2c_dev->irq); |
| 76 | phy->irq_active = false; |
| 77 | } |
| 78 | |
| 79 | /* |
| 80 | * Writing a frame must not return the number of written bytes. |
| 81 | * It must return either zero for success, or <0 for error. |
| 82 | * In addition, it must not alter the skb |
| 83 | */ |
| 84 | static int st_nci_i2c_write(void *phy_id, struct sk_buff *skb) |
| 85 | { |
| 86 | int r = -1; |
| 87 | struct st_nci_i2c_phy *phy = phy_id; |
| 88 | struct i2c_client *client = phy->i2c_dev; |
| 89 | |
| 90 | if (phy->ndlc->hard_fault != 0) |
| 91 | return phy->ndlc->hard_fault; |
| 92 | |
| 93 | r = i2c_master_send(client, skb->data, skb->len); |
| 94 | if (r < 0) { /* Retry, chip was in standby */ |
| 95 | usleep_range(1000, 4000); |
| 96 | r = i2c_master_send(client, skb->data, skb->len); |
| 97 | } |
| 98 | |
| 99 | if (r >= 0) { |
| 100 | if (r != skb->len) |
| 101 | r = -EREMOTEIO; |
| 102 | else |
| 103 | r = 0; |
| 104 | } |
| 105 | |
| 106 | return r; |
| 107 | } |
| 108 | |
| 109 | /* |
| 110 | * Reads an ndlc frame and returns it in a newly allocated sk_buff. |
| 111 | * returns: |
| 112 | * 0 : if received frame is complete |
| 113 | * -EREMOTEIO : i2c read error (fatal) |
| 114 | * -EBADMSG : frame was incorrect and discarded |
| 115 | * -ENOMEM : cannot allocate skb, frame dropped |
| 116 | */ |
| 117 | static int st_nci_i2c_read(struct st_nci_i2c_phy *phy, |
| 118 | struct sk_buff **skb) |
| 119 | { |
| 120 | int r; |
| 121 | u8 len; |
| 122 | u8 buf[ST_NCI_I2C_MAX_SIZE]; |
| 123 | struct i2c_client *client = phy->i2c_dev; |
| 124 | |
| 125 | r = i2c_master_recv(client, buf, ST_NCI_I2C_MIN_SIZE); |
| 126 | if (r < 0) { /* Retry, chip was in standby */ |
| 127 | usleep_range(1000, 4000); |
| 128 | r = i2c_master_recv(client, buf, ST_NCI_I2C_MIN_SIZE); |
| 129 | } |
| 130 | |
| 131 | if (r != ST_NCI_I2C_MIN_SIZE) |
| 132 | return -EREMOTEIO; |
| 133 | |
| 134 | len = be16_to_cpu(*(__be16 *) (buf + 2)); |
| 135 | if (len > ST_NCI_I2C_MAX_SIZE) { |
| 136 | nfc_err(&client->dev, "invalid frame len\n"); |
| 137 | return -EBADMSG; |
| 138 | } |
| 139 | |
| 140 | *skb = alloc_skb(ST_NCI_I2C_MIN_SIZE + len, GFP_KERNEL); |
| 141 | if (*skb == NULL) |
| 142 | return -ENOMEM; |
| 143 | |
| 144 | skb_reserve(*skb, ST_NCI_I2C_MIN_SIZE); |
| 145 | skb_put(*skb, ST_NCI_I2C_MIN_SIZE); |
| 146 | memcpy((*skb)->data, buf, ST_NCI_I2C_MIN_SIZE); |
| 147 | |
| 148 | if (!len) |
| 149 | return 0; |
| 150 | |
| 151 | r = i2c_master_recv(client, buf, len); |
| 152 | if (r != len) { |
| 153 | kfree_skb(*skb); |
| 154 | return -EREMOTEIO; |
| 155 | } |
| 156 | |
| 157 | skb_put(*skb, len); |
| 158 | memcpy((*skb)->data + ST_NCI_I2C_MIN_SIZE, buf, len); |
| 159 | |
| 160 | return 0; |
| 161 | } |
| 162 | |
| 163 | /* |
| 164 | * Reads an ndlc frame from the chip. |
| 165 | * |
| 166 | * On ST_NCI, IRQ goes in idle state when read starts. |
| 167 | */ |
| 168 | static irqreturn_t st_nci_irq_thread_fn(int irq, void *phy_id) |
| 169 | { |
| 170 | struct st_nci_i2c_phy *phy = phy_id; |
| 171 | struct i2c_client *client; |
| 172 | struct sk_buff *skb = NULL; |
| 173 | int r; |
| 174 | |
| 175 | if (!phy || !phy->ndlc || irq != phy->i2c_dev->irq) { |
| 176 | WARN_ON_ONCE(1); |
| 177 | return IRQ_NONE; |
| 178 | } |
| 179 | |
| 180 | client = phy->i2c_dev; |
| 181 | dev_dbg(&client->dev, "IRQ\n"); |
| 182 | |
| 183 | if (phy->ndlc->hard_fault) |
| 184 | return IRQ_HANDLED; |
| 185 | |
| 186 | if (!phy->ndlc->powered) { |
| 187 | st_nci_i2c_disable(phy); |
| 188 | return IRQ_HANDLED; |
| 189 | } |
| 190 | |
| 191 | r = st_nci_i2c_read(phy, &skb); |
| 192 | if (r == -EREMOTEIO || r == -ENOMEM || r == -EBADMSG) |
| 193 | return IRQ_HANDLED; |
| 194 | |
| 195 | ndlc_recv(phy->ndlc, skb); |
| 196 | |
| 197 | return IRQ_HANDLED; |
| 198 | } |
| 199 | |
| 200 | static struct nfc_phy_ops i2c_phy_ops = { |
| 201 | .write = st_nci_i2c_write, |
| 202 | .enable = st_nci_i2c_enable, |
| 203 | .disable = st_nci_i2c_disable, |
| 204 | }; |
| 205 | |
| 206 | static const struct acpi_gpio_params reset_gpios = { 1, 0, false }; |
| 207 | |
| 208 | static const struct acpi_gpio_mapping acpi_st_nci_gpios[] = { |
| 209 | { "reset-gpios", &reset_gpios, 1 }, |
| 210 | {}, |
| 211 | }; |
| 212 | |
| 213 | static int st_nci_i2c_probe(struct i2c_client *client, |
| 214 | const struct i2c_device_id *id) |
| 215 | { |
| 216 | struct device *dev = &client->dev; |
| 217 | struct st_nci_i2c_phy *phy; |
| 218 | int r; |
| 219 | |
| 220 | dev_dbg(&client->dev, "%s\n", __func__); |
| 221 | dev_dbg(&client->dev, "IRQ: %d\n", client->irq); |
| 222 | |
| 223 | if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { |
| 224 | nfc_err(&client->dev, "Need I2C_FUNC_I2C\n"); |
| 225 | return -ENODEV; |
| 226 | } |
| 227 | |
| 228 | phy = devm_kzalloc(dev, sizeof(struct st_nci_i2c_phy), GFP_KERNEL); |
| 229 | if (!phy) |
| 230 | return -ENOMEM; |
| 231 | |
| 232 | phy->i2c_dev = client; |
| 233 | |
| 234 | i2c_set_clientdata(client, phy); |
| 235 | |
| 236 | r = devm_acpi_dev_add_driver_gpios(dev, acpi_st_nci_gpios); |
| 237 | if (r) |
| 238 | dev_dbg(dev, "Unable to add GPIO mapping table\n"); |
| 239 | |
| 240 | /* Get RESET GPIO */ |
| 241 | phy->gpiod_reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); |
| 242 | if (IS_ERR(phy->gpiod_reset)) { |
| 243 | nfc_err(dev, "Unable to get RESET GPIO\n"); |
| 244 | return -ENODEV; |
| 245 | } |
| 246 | |
| 247 | phy->se_status.is_ese_present = |
| 248 | device_property_read_bool(dev, "ese-present"); |
| 249 | phy->se_status.is_uicc_present = |
| 250 | device_property_read_bool(dev, "uicc-present"); |
| 251 | |
| 252 | r = ndlc_probe(phy, &i2c_phy_ops, &client->dev, |
| 253 | ST_NCI_FRAME_HEADROOM, ST_NCI_FRAME_TAILROOM, |
| 254 | &phy->ndlc, &phy->se_status); |
| 255 | if (r < 0) { |
| 256 | nfc_err(&client->dev, "Unable to register ndlc layer\n"); |
| 257 | return r; |
| 258 | } |
| 259 | |
| 260 | phy->irq_active = true; |
| 261 | r = devm_request_threaded_irq(&client->dev, client->irq, NULL, |
| 262 | st_nci_irq_thread_fn, |
| 263 | IRQF_ONESHOT, |
| 264 | ST_NCI_DRIVER_NAME, phy); |
| 265 | if (r < 0) |
| 266 | nfc_err(&client->dev, "Unable to register IRQ handler\n"); |
| 267 | |
| 268 | return r; |
| 269 | } |
| 270 | |
| 271 | static int st_nci_i2c_remove(struct i2c_client *client) |
| 272 | { |
| 273 | struct st_nci_i2c_phy *phy = i2c_get_clientdata(client); |
| 274 | |
| 275 | dev_dbg(&client->dev, "%s\n", __func__); |
| 276 | |
| 277 | ndlc_remove(phy->ndlc); |
| 278 | |
| 279 | return 0; |
| 280 | } |
| 281 | |
| 282 | static struct i2c_device_id st_nci_i2c_id_table[] = { |
| 283 | {ST_NCI_DRIVER_NAME, 0}, |
| 284 | {} |
| 285 | }; |
| 286 | MODULE_DEVICE_TABLE(i2c, st_nci_i2c_id_table); |
| 287 | |
| 288 | static const struct acpi_device_id st_nci_i2c_acpi_match[] = { |
| 289 | {"SMO2101"}, |
| 290 | {"SMO2102"}, |
| 291 | {} |
| 292 | }; |
| 293 | MODULE_DEVICE_TABLE(acpi, st_nci_i2c_acpi_match); |
| 294 | |
| 295 | static const struct of_device_id of_st_nci_i2c_match[] = { |
| 296 | { .compatible = "st,st21nfcb-i2c", }, |
| 297 | { .compatible = "st,st21nfcb_i2c", }, |
| 298 | { .compatible = "st,st21nfcc-i2c", }, |
| 299 | {} |
| 300 | }; |
| 301 | MODULE_DEVICE_TABLE(of, of_st_nci_i2c_match); |
| 302 | |
| 303 | static struct i2c_driver st_nci_i2c_driver = { |
| 304 | .driver = { |
| 305 | .name = ST_NCI_I2C_DRIVER_NAME, |
| 306 | .of_match_table = of_match_ptr(of_st_nci_i2c_match), |
| 307 | .acpi_match_table = ACPI_PTR(st_nci_i2c_acpi_match), |
| 308 | }, |
| 309 | .probe = st_nci_i2c_probe, |
| 310 | .id_table = st_nci_i2c_id_table, |
| 311 | .remove = st_nci_i2c_remove, |
| 312 | }; |
| 313 | module_i2c_driver(st_nci_i2c_driver); |
| 314 | |
| 315 | MODULE_LICENSE("GPL"); |
| 316 | MODULE_DESCRIPTION(DRIVER_DESC); |