rjw | 1f88458 | 2022-01-06 17:20:42 +0800 | [diff] [blame^] | 1 | /* |
| 2 | * Pin controller and GPIO driver for Amlogic Meson SoCs |
| 3 | * |
| 4 | * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com> |
| 5 | * |
| 6 | * This program is free software; you can redistribute it and/or |
| 7 | * modify it under the terms of the GNU General Public License |
| 8 | * version 2 as published by the Free Software Foundation. |
| 9 | * |
| 10 | * You should have received a copy of the GNU General Public License |
| 11 | * along with this program. If not, see <http://www.gnu.org/licenses/>. |
| 12 | */ |
| 13 | |
| 14 | /* |
| 15 | * The available pins are organized in banks (A,B,C,D,E,X,Y,Z,AO, |
| 16 | * BOOT,CARD for meson6, X,Y,DV,H,Z,AO,BOOT,CARD for meson8 and |
| 17 | * X,Y,DV,H,AO,BOOT,CARD,DIF for meson8b) and each bank has a |
| 18 | * variable number of pins. |
| 19 | * |
| 20 | * The AO bank is special because it belongs to the Always-On power |
| 21 | * domain which can't be powered off; the bank also uses a set of |
| 22 | * registers different from the other banks. |
| 23 | * |
| 24 | * For each pin controller there are 4 different register ranges that |
| 25 | * control the following properties of the pins: |
| 26 | * 1) pin muxing |
| 27 | * 2) pull enable/disable |
| 28 | * 3) pull up/down |
| 29 | * 4) GPIO direction, output value, input value |
| 30 | * |
| 31 | * In some cases the register ranges for pull enable and pull |
| 32 | * direction are the same and thus there are only 3 register ranges. |
| 33 | * |
| 34 | * Every pinmux group can be enabled by a specific bit in the first |
| 35 | * register range; when all groups for a given pin are disabled the |
| 36 | * pin acts as a GPIO. |
| 37 | * |
| 38 | * For the pull and GPIO configuration every bank uses a contiguous |
| 39 | * set of bits in the register sets described above; the same register |
| 40 | * can be shared by more banks with different offsets. |
| 41 | * |
| 42 | * In addition to this there are some registers shared between all |
| 43 | * banks that control the IRQ functionality. This feature is not |
| 44 | * supported at the moment by the driver. |
| 45 | */ |
| 46 | |
| 47 | #include <linux/device.h> |
| 48 | #include <linux/gpio.h> |
| 49 | #include <linux/init.h> |
| 50 | #include <linux/io.h> |
| 51 | #include <linux/of.h> |
| 52 | #include <linux/of_address.h> |
| 53 | #include <linux/pinctrl/pinconf-generic.h> |
| 54 | #include <linux/pinctrl/pinconf.h> |
| 55 | #include <linux/pinctrl/pinctrl.h> |
| 56 | #include <linux/pinctrl/pinmux.h> |
| 57 | #include <linux/platform_device.h> |
| 58 | #include <linux/regmap.h> |
| 59 | #include <linux/seq_file.h> |
| 60 | |
| 61 | #include "../core.h" |
| 62 | #include "../pinctrl-utils.h" |
| 63 | #include "pinctrl-meson.h" |
| 64 | |
| 65 | /** |
| 66 | * meson_get_bank() - find the bank containing a given pin |
| 67 | * |
| 68 | * @pc: the pinctrl instance |
| 69 | * @pin: the pin number |
| 70 | * @bank: the found bank |
| 71 | * |
| 72 | * Return: 0 on success, a negative value on error |
| 73 | */ |
| 74 | static int meson_get_bank(struct meson_pinctrl *pc, unsigned int pin, |
| 75 | struct meson_bank **bank) |
| 76 | { |
| 77 | int i; |
| 78 | |
| 79 | for (i = 0; i < pc->data->num_banks; i++) { |
| 80 | if (pin >= pc->data->banks[i].first && |
| 81 | pin <= pc->data->banks[i].last) { |
| 82 | *bank = &pc->data->banks[i]; |
| 83 | return 0; |
| 84 | } |
| 85 | } |
| 86 | |
| 87 | return -EINVAL; |
| 88 | } |
| 89 | |
| 90 | /** |
| 91 | * meson_calc_reg_and_bit() - calculate register and bit for a pin |
| 92 | * |
| 93 | * @bank: the bank containing the pin |
| 94 | * @pin: the pin number |
| 95 | * @reg_type: the type of register needed (pull-enable, pull, etc...) |
| 96 | * @reg: the computed register offset |
| 97 | * @bit: the computed bit |
| 98 | */ |
| 99 | static void meson_calc_reg_and_bit(struct meson_bank *bank, unsigned int pin, |
| 100 | enum meson_reg_type reg_type, |
| 101 | unsigned int *reg, unsigned int *bit) |
| 102 | { |
| 103 | struct meson_reg_desc *desc = &bank->regs[reg_type]; |
| 104 | |
| 105 | *reg = desc->reg * 4; |
| 106 | *bit = desc->bit + pin - bank->first; |
| 107 | } |
| 108 | |
| 109 | static int meson_get_groups_count(struct pinctrl_dev *pcdev) |
| 110 | { |
| 111 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 112 | |
| 113 | return pc->data->num_groups; |
| 114 | } |
| 115 | |
| 116 | static const char *meson_get_group_name(struct pinctrl_dev *pcdev, |
| 117 | unsigned selector) |
| 118 | { |
| 119 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 120 | |
| 121 | return pc->data->groups[selector].name; |
| 122 | } |
| 123 | |
| 124 | static int meson_get_group_pins(struct pinctrl_dev *pcdev, unsigned selector, |
| 125 | const unsigned **pins, unsigned *num_pins) |
| 126 | { |
| 127 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 128 | |
| 129 | *pins = pc->data->groups[selector].pins; |
| 130 | *num_pins = pc->data->groups[selector].num_pins; |
| 131 | |
| 132 | return 0; |
| 133 | } |
| 134 | |
| 135 | static void meson_pin_dbg_show(struct pinctrl_dev *pcdev, struct seq_file *s, |
| 136 | unsigned offset) |
| 137 | { |
| 138 | seq_printf(s, " %s", dev_name(pcdev->dev)); |
| 139 | } |
| 140 | |
| 141 | static const struct pinctrl_ops meson_pctrl_ops = { |
| 142 | .get_groups_count = meson_get_groups_count, |
| 143 | .get_group_name = meson_get_group_name, |
| 144 | .get_group_pins = meson_get_group_pins, |
| 145 | .dt_node_to_map = pinconf_generic_dt_node_to_map_all, |
| 146 | .dt_free_map = pinctrl_utils_free_map, |
| 147 | .pin_dbg_show = meson_pin_dbg_show, |
| 148 | }; |
| 149 | |
| 150 | /** |
| 151 | * meson_pmx_disable_other_groups() - disable other groups using a given pin |
| 152 | * |
| 153 | * @pc: meson pin controller device |
| 154 | * @pin: number of the pin |
| 155 | * @sel_group: index of the selected group, or -1 if none |
| 156 | * |
| 157 | * The function disables all pinmux groups using a pin except the |
| 158 | * selected one. If @sel_group is -1 all groups are disabled, leaving |
| 159 | * the pin in GPIO mode. |
| 160 | */ |
| 161 | static void meson_pmx_disable_other_groups(struct meson_pinctrl *pc, |
| 162 | unsigned int pin, int sel_group) |
| 163 | { |
| 164 | struct meson_pmx_group *group; |
| 165 | int i, j; |
| 166 | |
| 167 | for (i = 0; i < pc->data->num_groups; i++) { |
| 168 | group = &pc->data->groups[i]; |
| 169 | if (group->is_gpio || i == sel_group) |
| 170 | continue; |
| 171 | |
| 172 | for (j = 0; j < group->num_pins; j++) { |
| 173 | if (group->pins[j] == pin) { |
| 174 | /* We have found a group using the pin */ |
| 175 | regmap_update_bits(pc->reg_mux, |
| 176 | group->reg * 4, |
| 177 | BIT(group->bit), 0); |
| 178 | } |
| 179 | } |
| 180 | } |
| 181 | } |
| 182 | |
| 183 | static int meson_pmx_set_mux(struct pinctrl_dev *pcdev, unsigned func_num, |
| 184 | unsigned group_num) |
| 185 | { |
| 186 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 187 | struct meson_pmx_func *func = &pc->data->funcs[func_num]; |
| 188 | struct meson_pmx_group *group = &pc->data->groups[group_num]; |
| 189 | int i, ret = 0; |
| 190 | |
| 191 | dev_dbg(pc->dev, "enable function %s, group %s\n", func->name, |
| 192 | group->name); |
| 193 | |
| 194 | /* |
| 195 | * Disable groups using the same pin. |
| 196 | * The selected group is not disabled to avoid glitches. |
| 197 | */ |
| 198 | for (i = 0; i < group->num_pins; i++) |
| 199 | meson_pmx_disable_other_groups(pc, group->pins[i], group_num); |
| 200 | |
| 201 | /* Function 0 (GPIO) doesn't need any additional setting */ |
| 202 | if (func_num) |
| 203 | ret = regmap_update_bits(pc->reg_mux, group->reg * 4, |
| 204 | BIT(group->bit), BIT(group->bit)); |
| 205 | |
| 206 | return ret; |
| 207 | } |
| 208 | |
| 209 | static int meson_pmx_request_gpio(struct pinctrl_dev *pcdev, |
| 210 | struct pinctrl_gpio_range *range, |
| 211 | unsigned offset) |
| 212 | { |
| 213 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 214 | |
| 215 | meson_pmx_disable_other_groups(pc, offset, -1); |
| 216 | |
| 217 | return 0; |
| 218 | } |
| 219 | |
| 220 | static int meson_pmx_get_funcs_count(struct pinctrl_dev *pcdev) |
| 221 | { |
| 222 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 223 | |
| 224 | return pc->data->num_funcs; |
| 225 | } |
| 226 | |
| 227 | static const char *meson_pmx_get_func_name(struct pinctrl_dev *pcdev, |
| 228 | unsigned selector) |
| 229 | { |
| 230 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 231 | |
| 232 | return pc->data->funcs[selector].name; |
| 233 | } |
| 234 | |
| 235 | static int meson_pmx_get_groups(struct pinctrl_dev *pcdev, unsigned selector, |
| 236 | const char * const **groups, |
| 237 | unsigned * const num_groups) |
| 238 | { |
| 239 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 240 | |
| 241 | *groups = pc->data->funcs[selector].groups; |
| 242 | *num_groups = pc->data->funcs[selector].num_groups; |
| 243 | |
| 244 | return 0; |
| 245 | } |
| 246 | |
| 247 | static const struct pinmux_ops meson_pmx_ops = { |
| 248 | .set_mux = meson_pmx_set_mux, |
| 249 | .get_functions_count = meson_pmx_get_funcs_count, |
| 250 | .get_function_name = meson_pmx_get_func_name, |
| 251 | .get_function_groups = meson_pmx_get_groups, |
| 252 | .gpio_request_enable = meson_pmx_request_gpio, |
| 253 | }; |
| 254 | |
| 255 | static int meson_pinconf_set(struct pinctrl_dev *pcdev, unsigned int pin, |
| 256 | unsigned long *configs, unsigned num_configs) |
| 257 | { |
| 258 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 259 | struct meson_bank *bank; |
| 260 | enum pin_config_param param; |
| 261 | unsigned int reg, bit; |
| 262 | int i, ret; |
| 263 | |
| 264 | ret = meson_get_bank(pc, pin, &bank); |
| 265 | if (ret) |
| 266 | return ret; |
| 267 | |
| 268 | for (i = 0; i < num_configs; i++) { |
| 269 | param = pinconf_to_config_param(configs[i]); |
| 270 | |
| 271 | switch (param) { |
| 272 | case PIN_CONFIG_BIAS_DISABLE: |
| 273 | dev_dbg(pc->dev, "pin %u: disable bias\n", pin); |
| 274 | |
| 275 | meson_calc_reg_and_bit(bank, pin, REG_PULLEN, ®, |
| 276 | &bit); |
| 277 | ret = regmap_update_bits(pc->reg_pullen, reg, |
| 278 | BIT(bit), 0); |
| 279 | if (ret) |
| 280 | return ret; |
| 281 | break; |
| 282 | case PIN_CONFIG_BIAS_PULL_UP: |
| 283 | dev_dbg(pc->dev, "pin %u: enable pull-up\n", pin); |
| 284 | |
| 285 | meson_calc_reg_and_bit(bank, pin, REG_PULLEN, |
| 286 | ®, &bit); |
| 287 | ret = regmap_update_bits(pc->reg_pullen, reg, |
| 288 | BIT(bit), BIT(bit)); |
| 289 | if (ret) |
| 290 | return ret; |
| 291 | |
| 292 | meson_calc_reg_and_bit(bank, pin, REG_PULL, ®, &bit); |
| 293 | ret = regmap_update_bits(pc->reg_pull, reg, |
| 294 | BIT(bit), BIT(bit)); |
| 295 | if (ret) |
| 296 | return ret; |
| 297 | break; |
| 298 | case PIN_CONFIG_BIAS_PULL_DOWN: |
| 299 | dev_dbg(pc->dev, "pin %u: enable pull-down\n", pin); |
| 300 | |
| 301 | meson_calc_reg_and_bit(bank, pin, REG_PULLEN, |
| 302 | ®, &bit); |
| 303 | ret = regmap_update_bits(pc->reg_pullen, reg, |
| 304 | BIT(bit), BIT(bit)); |
| 305 | if (ret) |
| 306 | return ret; |
| 307 | |
| 308 | meson_calc_reg_and_bit(bank, pin, REG_PULL, ®, &bit); |
| 309 | ret = regmap_update_bits(pc->reg_pull, reg, |
| 310 | BIT(bit), 0); |
| 311 | if (ret) |
| 312 | return ret; |
| 313 | break; |
| 314 | default: |
| 315 | return -ENOTSUPP; |
| 316 | } |
| 317 | } |
| 318 | |
| 319 | return 0; |
| 320 | } |
| 321 | |
| 322 | static int meson_pinconf_get_pull(struct meson_pinctrl *pc, unsigned int pin) |
| 323 | { |
| 324 | struct meson_bank *bank; |
| 325 | unsigned int reg, bit, val; |
| 326 | int ret, conf; |
| 327 | |
| 328 | ret = meson_get_bank(pc, pin, &bank); |
| 329 | if (ret) |
| 330 | return ret; |
| 331 | |
| 332 | meson_calc_reg_and_bit(bank, pin, REG_PULLEN, ®, &bit); |
| 333 | |
| 334 | ret = regmap_read(pc->reg_pullen, reg, &val); |
| 335 | if (ret) |
| 336 | return ret; |
| 337 | |
| 338 | if (!(val & BIT(bit))) { |
| 339 | conf = PIN_CONFIG_BIAS_DISABLE; |
| 340 | } else { |
| 341 | meson_calc_reg_and_bit(bank, pin, REG_PULL, ®, &bit); |
| 342 | |
| 343 | ret = regmap_read(pc->reg_pull, reg, &val); |
| 344 | if (ret) |
| 345 | return ret; |
| 346 | |
| 347 | if (val & BIT(bit)) |
| 348 | conf = PIN_CONFIG_BIAS_PULL_UP; |
| 349 | else |
| 350 | conf = PIN_CONFIG_BIAS_PULL_DOWN; |
| 351 | } |
| 352 | |
| 353 | return conf; |
| 354 | } |
| 355 | |
| 356 | static int meson_pinconf_get(struct pinctrl_dev *pcdev, unsigned int pin, |
| 357 | unsigned long *config) |
| 358 | { |
| 359 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 360 | enum pin_config_param param = pinconf_to_config_param(*config); |
| 361 | u16 arg; |
| 362 | |
| 363 | switch (param) { |
| 364 | case PIN_CONFIG_BIAS_DISABLE: |
| 365 | case PIN_CONFIG_BIAS_PULL_DOWN: |
| 366 | case PIN_CONFIG_BIAS_PULL_UP: |
| 367 | if (meson_pinconf_get_pull(pc, pin) == param) |
| 368 | arg = 1; |
| 369 | else |
| 370 | return -EINVAL; |
| 371 | break; |
| 372 | default: |
| 373 | return -ENOTSUPP; |
| 374 | } |
| 375 | |
| 376 | *config = pinconf_to_config_packed(param, arg); |
| 377 | dev_dbg(pc->dev, "pinconf for pin %u is %lu\n", pin, *config); |
| 378 | |
| 379 | return 0; |
| 380 | } |
| 381 | |
| 382 | static int meson_pinconf_group_set(struct pinctrl_dev *pcdev, |
| 383 | unsigned int num_group, |
| 384 | unsigned long *configs, unsigned num_configs) |
| 385 | { |
| 386 | struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); |
| 387 | struct meson_pmx_group *group = &pc->data->groups[num_group]; |
| 388 | int i; |
| 389 | |
| 390 | dev_dbg(pc->dev, "set pinconf for group %s\n", group->name); |
| 391 | |
| 392 | for (i = 0; i < group->num_pins; i++) { |
| 393 | meson_pinconf_set(pcdev, group->pins[i], configs, |
| 394 | num_configs); |
| 395 | } |
| 396 | |
| 397 | return 0; |
| 398 | } |
| 399 | |
| 400 | static int meson_pinconf_group_get(struct pinctrl_dev *pcdev, |
| 401 | unsigned int group, unsigned long *config) |
| 402 | { |
| 403 | return -ENOSYS; |
| 404 | } |
| 405 | |
| 406 | static const struct pinconf_ops meson_pinconf_ops = { |
| 407 | .pin_config_get = meson_pinconf_get, |
| 408 | .pin_config_set = meson_pinconf_set, |
| 409 | .pin_config_group_get = meson_pinconf_group_get, |
| 410 | .pin_config_group_set = meson_pinconf_group_set, |
| 411 | .is_generic = true, |
| 412 | }; |
| 413 | |
| 414 | static int meson_gpio_request(struct gpio_chip *chip, unsigned gpio) |
| 415 | { |
| 416 | return pinctrl_request_gpio(chip->base + gpio); |
| 417 | } |
| 418 | |
| 419 | static void meson_gpio_free(struct gpio_chip *chip, unsigned gpio) |
| 420 | { |
| 421 | struct meson_pinctrl *pc = gpiochip_get_data(chip); |
| 422 | |
| 423 | pinctrl_free_gpio(pc->data->pin_base + gpio); |
| 424 | } |
| 425 | |
| 426 | static int meson_gpio_direction_input(struct gpio_chip *chip, unsigned gpio) |
| 427 | { |
| 428 | struct meson_pinctrl *pc = gpiochip_get_data(chip); |
| 429 | unsigned int reg, bit, pin; |
| 430 | struct meson_bank *bank; |
| 431 | int ret; |
| 432 | |
| 433 | pin = pc->data->pin_base + gpio; |
| 434 | ret = meson_get_bank(pc, pin, &bank); |
| 435 | if (ret) |
| 436 | return ret; |
| 437 | |
| 438 | meson_calc_reg_and_bit(bank, pin, REG_DIR, ®, &bit); |
| 439 | |
| 440 | return regmap_update_bits(pc->reg_gpio, reg, BIT(bit), BIT(bit)); |
| 441 | } |
| 442 | |
| 443 | static int meson_gpio_direction_output(struct gpio_chip *chip, unsigned gpio, |
| 444 | int value) |
| 445 | { |
| 446 | struct meson_pinctrl *pc = gpiochip_get_data(chip); |
| 447 | unsigned int reg, bit, pin; |
| 448 | struct meson_bank *bank; |
| 449 | int ret; |
| 450 | |
| 451 | pin = pc->data->pin_base + gpio; |
| 452 | ret = meson_get_bank(pc, pin, &bank); |
| 453 | if (ret) |
| 454 | return ret; |
| 455 | |
| 456 | meson_calc_reg_and_bit(bank, pin, REG_DIR, ®, &bit); |
| 457 | ret = regmap_update_bits(pc->reg_gpio, reg, BIT(bit), 0); |
| 458 | if (ret) |
| 459 | return ret; |
| 460 | |
| 461 | meson_calc_reg_and_bit(bank, pin, REG_OUT, ®, &bit); |
| 462 | return regmap_update_bits(pc->reg_gpio, reg, BIT(bit), |
| 463 | value ? BIT(bit) : 0); |
| 464 | } |
| 465 | |
| 466 | static void meson_gpio_set(struct gpio_chip *chip, unsigned gpio, int value) |
| 467 | { |
| 468 | struct meson_pinctrl *pc = gpiochip_get_data(chip); |
| 469 | unsigned int reg, bit, pin; |
| 470 | struct meson_bank *bank; |
| 471 | int ret; |
| 472 | |
| 473 | pin = pc->data->pin_base + gpio; |
| 474 | ret = meson_get_bank(pc, pin, &bank); |
| 475 | if (ret) |
| 476 | return; |
| 477 | |
| 478 | meson_calc_reg_and_bit(bank, pin, REG_OUT, ®, &bit); |
| 479 | regmap_update_bits(pc->reg_gpio, reg, BIT(bit), |
| 480 | value ? BIT(bit) : 0); |
| 481 | } |
| 482 | |
| 483 | static int meson_gpio_get(struct gpio_chip *chip, unsigned gpio) |
| 484 | { |
| 485 | struct meson_pinctrl *pc = gpiochip_get_data(chip); |
| 486 | unsigned int reg, bit, val, pin; |
| 487 | struct meson_bank *bank; |
| 488 | int ret; |
| 489 | |
| 490 | pin = pc->data->pin_base + gpio; |
| 491 | ret = meson_get_bank(pc, pin, &bank); |
| 492 | if (ret) |
| 493 | return ret; |
| 494 | |
| 495 | meson_calc_reg_and_bit(bank, pin, REG_IN, ®, &bit); |
| 496 | regmap_read(pc->reg_gpio, reg, &val); |
| 497 | |
| 498 | return !!(val & BIT(bit)); |
| 499 | } |
| 500 | |
| 501 | static const struct of_device_id meson_pinctrl_dt_match[] = { |
| 502 | { |
| 503 | .compatible = "amlogic,meson8-cbus-pinctrl", |
| 504 | .data = &meson8_cbus_pinctrl_data, |
| 505 | }, |
| 506 | { |
| 507 | .compatible = "amlogic,meson8b-cbus-pinctrl", |
| 508 | .data = &meson8b_cbus_pinctrl_data, |
| 509 | }, |
| 510 | { |
| 511 | .compatible = "amlogic,meson8-aobus-pinctrl", |
| 512 | .data = &meson8_aobus_pinctrl_data, |
| 513 | }, |
| 514 | { |
| 515 | .compatible = "amlogic,meson8b-aobus-pinctrl", |
| 516 | .data = &meson8b_aobus_pinctrl_data, |
| 517 | }, |
| 518 | { |
| 519 | .compatible = "amlogic,meson-gxbb-periphs-pinctrl", |
| 520 | .data = &meson_gxbb_periphs_pinctrl_data, |
| 521 | }, |
| 522 | { |
| 523 | .compatible = "amlogic,meson-gxbb-aobus-pinctrl", |
| 524 | .data = &meson_gxbb_aobus_pinctrl_data, |
| 525 | }, |
| 526 | { |
| 527 | .compatible = "amlogic,meson-gxl-periphs-pinctrl", |
| 528 | .data = &meson_gxl_periphs_pinctrl_data, |
| 529 | }, |
| 530 | { |
| 531 | .compatible = "amlogic,meson-gxl-aobus-pinctrl", |
| 532 | .data = &meson_gxl_aobus_pinctrl_data, |
| 533 | }, |
| 534 | { }, |
| 535 | }; |
| 536 | |
| 537 | static int meson_gpiolib_register(struct meson_pinctrl *pc) |
| 538 | { |
| 539 | int ret; |
| 540 | |
| 541 | pc->chip.label = pc->data->name; |
| 542 | pc->chip.parent = pc->dev; |
| 543 | pc->chip.request = meson_gpio_request; |
| 544 | pc->chip.free = meson_gpio_free; |
| 545 | pc->chip.direction_input = meson_gpio_direction_input; |
| 546 | pc->chip.direction_output = meson_gpio_direction_output; |
| 547 | pc->chip.get = meson_gpio_get; |
| 548 | pc->chip.set = meson_gpio_set; |
| 549 | pc->chip.base = pc->data->pin_base; |
| 550 | pc->chip.ngpio = pc->data->num_pins; |
| 551 | pc->chip.can_sleep = false; |
| 552 | pc->chip.of_node = pc->of_node; |
| 553 | pc->chip.of_gpio_n_cells = 2; |
| 554 | |
| 555 | ret = gpiochip_add_data(&pc->chip, pc); |
| 556 | if (ret) { |
| 557 | dev_err(pc->dev, "can't add gpio chip %s\n", |
| 558 | pc->data->name); |
| 559 | return ret; |
| 560 | } |
| 561 | |
| 562 | return 0; |
| 563 | } |
| 564 | |
| 565 | static struct regmap_config meson_regmap_config = { |
| 566 | .reg_bits = 32, |
| 567 | .val_bits = 32, |
| 568 | .reg_stride = 4, |
| 569 | }; |
| 570 | |
| 571 | static struct regmap *meson_map_resource(struct meson_pinctrl *pc, |
| 572 | struct device_node *node, char *name) |
| 573 | { |
| 574 | struct resource res; |
| 575 | void __iomem *base; |
| 576 | int i; |
| 577 | |
| 578 | i = of_property_match_string(node, "reg-names", name); |
| 579 | if (of_address_to_resource(node, i, &res)) |
| 580 | return ERR_PTR(-ENOENT); |
| 581 | |
| 582 | base = devm_ioremap_resource(pc->dev, &res); |
| 583 | if (IS_ERR(base)) |
| 584 | return ERR_CAST(base); |
| 585 | |
| 586 | meson_regmap_config.max_register = resource_size(&res) - 4; |
| 587 | meson_regmap_config.name = devm_kasprintf(pc->dev, GFP_KERNEL, |
| 588 | "%s-%s", node->name, |
| 589 | name); |
| 590 | if (!meson_regmap_config.name) |
| 591 | return ERR_PTR(-ENOMEM); |
| 592 | |
| 593 | return devm_regmap_init_mmio(pc->dev, base, &meson_regmap_config); |
| 594 | } |
| 595 | |
| 596 | static int meson_pinctrl_parse_dt(struct meson_pinctrl *pc, |
| 597 | struct device_node *node) |
| 598 | { |
| 599 | struct device_node *np, *gpio_np = NULL; |
| 600 | |
| 601 | for_each_child_of_node(node, np) { |
| 602 | if (!of_find_property(np, "gpio-controller", NULL)) |
| 603 | continue; |
| 604 | if (gpio_np) { |
| 605 | dev_err(pc->dev, "multiple gpio nodes\n"); |
| 606 | return -EINVAL; |
| 607 | } |
| 608 | gpio_np = np; |
| 609 | } |
| 610 | |
| 611 | if (!gpio_np) { |
| 612 | dev_err(pc->dev, "no gpio node found\n"); |
| 613 | return -EINVAL; |
| 614 | } |
| 615 | |
| 616 | pc->of_node = gpio_np; |
| 617 | |
| 618 | pc->reg_mux = meson_map_resource(pc, gpio_np, "mux"); |
| 619 | if (IS_ERR(pc->reg_mux)) { |
| 620 | dev_err(pc->dev, "mux registers not found\n"); |
| 621 | return PTR_ERR(pc->reg_mux); |
| 622 | } |
| 623 | |
| 624 | pc->reg_pull = meson_map_resource(pc, gpio_np, "pull"); |
| 625 | if (IS_ERR(pc->reg_pull)) { |
| 626 | dev_err(pc->dev, "pull registers not found\n"); |
| 627 | return PTR_ERR(pc->reg_pull); |
| 628 | } |
| 629 | |
| 630 | pc->reg_pullen = meson_map_resource(pc, gpio_np, "pull-enable"); |
| 631 | /* Use pull region if pull-enable one is not present */ |
| 632 | if (IS_ERR(pc->reg_pullen)) |
| 633 | pc->reg_pullen = pc->reg_pull; |
| 634 | |
| 635 | pc->reg_gpio = meson_map_resource(pc, gpio_np, "gpio"); |
| 636 | if (IS_ERR(pc->reg_gpio)) { |
| 637 | dev_err(pc->dev, "gpio registers not found\n"); |
| 638 | return PTR_ERR(pc->reg_gpio); |
| 639 | } |
| 640 | |
| 641 | return 0; |
| 642 | } |
| 643 | |
| 644 | static int meson_pinctrl_probe(struct platform_device *pdev) |
| 645 | { |
| 646 | const struct of_device_id *match; |
| 647 | struct device *dev = &pdev->dev; |
| 648 | struct meson_pinctrl *pc; |
| 649 | int ret; |
| 650 | |
| 651 | pc = devm_kzalloc(dev, sizeof(struct meson_pinctrl), GFP_KERNEL); |
| 652 | if (!pc) |
| 653 | return -ENOMEM; |
| 654 | |
| 655 | pc->dev = dev; |
| 656 | match = of_match_node(meson_pinctrl_dt_match, pdev->dev.of_node); |
| 657 | pc->data = (struct meson_pinctrl_data *) match->data; |
| 658 | |
| 659 | ret = meson_pinctrl_parse_dt(pc, pdev->dev.of_node); |
| 660 | if (ret) |
| 661 | return ret; |
| 662 | |
| 663 | pc->desc.name = "pinctrl-meson"; |
| 664 | pc->desc.owner = THIS_MODULE; |
| 665 | pc->desc.pctlops = &meson_pctrl_ops; |
| 666 | pc->desc.pmxops = &meson_pmx_ops; |
| 667 | pc->desc.confops = &meson_pinconf_ops; |
| 668 | pc->desc.pins = pc->data->pins; |
| 669 | pc->desc.npins = pc->data->num_pins; |
| 670 | |
| 671 | pc->pcdev = devm_pinctrl_register(pc->dev, &pc->desc, pc); |
| 672 | if (IS_ERR(pc->pcdev)) { |
| 673 | dev_err(pc->dev, "can't register pinctrl device"); |
| 674 | return PTR_ERR(pc->pcdev); |
| 675 | } |
| 676 | |
| 677 | return meson_gpiolib_register(pc); |
| 678 | } |
| 679 | |
| 680 | static struct platform_driver meson_pinctrl_driver = { |
| 681 | .probe = meson_pinctrl_probe, |
| 682 | .driver = { |
| 683 | .name = "meson-pinctrl", |
| 684 | .of_match_table = meson_pinctrl_dt_match, |
| 685 | }, |
| 686 | }; |
| 687 | builtin_platform_driver(meson_pinctrl_driver); |