|  | /* | 
|  | *  MAX732x I2C Port Expander with 8/16 I/O | 
|  | * | 
|  | *  Copyright (C) 2007 Marvell International Ltd. | 
|  | *  Copyright (C) 2008 Jack Ren <jack.ren@marvell.com> | 
|  | *  Copyright (C) 2008 Eric Miao <eric.miao@marvell.com> | 
|  | * | 
|  | *  Derived from drivers/gpio/pca953x.c | 
|  | * | 
|  | *  This program is free software; you can redistribute it and/or modify | 
|  | *  it under the terms of the GNU General Public License as published by | 
|  | *  the Free Software Foundation; version 2 of the License. | 
|  | */ | 
|  |  | 
|  | #include <linux/module.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/slab.h> | 
|  | #include <linux/string.h> | 
|  | #include <linux/gpio.h> | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/irq.h> | 
|  | #include <linux/i2c.h> | 
|  | #include <linux/i2c/max732x.h> | 
|  |  | 
|  |  | 
|  | /* | 
|  | * Each port of MAX732x (including MAX7319) falls into one of the | 
|  | * following three types: | 
|  | * | 
|  | *   - Push Pull Output | 
|  | *   - Input | 
|  | *   - Open Drain I/O | 
|  | * | 
|  | * designated by 'O', 'I' and 'P' individually according to MAXIM's | 
|  | * datasheets. 'I' and 'P' ports are interrupt capables, some with | 
|  | * a dedicated interrupt mask. | 
|  | * | 
|  | * There are two groups of I/O ports, each group usually includes | 
|  | * up to 8 I/O ports, and is accessed by a specific I2C address: | 
|  | * | 
|  | *   - Group A : by I2C address 0b'110xxxx | 
|  | *   - Group B : by I2C address 0b'101xxxx | 
|  | * | 
|  | * where 'xxxx' is decided by the connections of pin AD2/AD0.  The | 
|  | * address used also affects the initial state of output signals. | 
|  | * | 
|  | * Within each group of ports, there are five known combinations of | 
|  | * I/O ports: 4I4O, 4P4O, 8I, 8P, 8O, see the definitions below for | 
|  | * the detailed organization of these ports. Only Goup A is interrupt | 
|  | * capable. | 
|  | * | 
|  | * GPIO numbers start from 'gpio_base + 0' to 'gpio_base + 8/16', | 
|  | * and GPIOs from GROUP_A are numbered before those from GROUP_B | 
|  | * (if there are two groups). | 
|  | * | 
|  | * NOTE: MAX7328/MAX7329 are drop-in replacements for PCF8574/a, so | 
|  | * they are not supported by this driver. | 
|  | */ | 
|  |  | 
|  | #define PORT_NONE	0x0	/* '/' No Port */ | 
|  | #define PORT_OUTPUT	0x1	/* 'O' Push-Pull, Output Only */ | 
|  | #define PORT_INPUT	0x2	/* 'I' Input Only */ | 
|  | #define PORT_OPENDRAIN	0x3	/* 'P' Open-Drain, I/O */ | 
|  |  | 
|  | #define IO_4I4O		0x5AA5	/* O7 O6 I5 I4 I3 I2 O1 O0 */ | 
|  | #define IO_4P4O		0x5FF5	/* O7 O6 P5 P4 P3 P2 O1 O0 */ | 
|  | #define IO_8I		0xAAAA	/* I7 I6 I5 I4 I3 I2 I1 I0 */ | 
|  | #define IO_8P		0xFFFF	/* P7 P6 P5 P4 P3 P2 P1 P0 */ | 
|  | #define IO_8O		0x5555	/* O7 O6 O5 O4 O3 O2 O1 O0 */ | 
|  |  | 
|  | #define GROUP_A(x)	((x) & 0xffff)	/* I2C Addr: 0b'110xxxx */ | 
|  | #define GROUP_B(x)	((x) << 16)	/* I2C Addr: 0b'101xxxx */ | 
|  |  | 
|  | #define INT_NONE	0x0	/* No interrupt capability */ | 
|  | #define INT_NO_MASK	0x1	/* Has interrupts, no mask */ | 
|  | #define INT_INDEP_MASK	0x2	/* Has interrupts, independent mask */ | 
|  | #define INT_MERGED_MASK 0x3	/* Has interrupts, merged mask */ | 
|  |  | 
|  | #define INT_CAPS(x)	(((uint64_t)(x)) << 32) | 
|  |  | 
|  | enum { | 
|  | MAX7319, | 
|  | MAX7320, | 
|  | MAX7321, | 
|  | MAX7322, | 
|  | MAX7323, | 
|  | MAX7324, | 
|  | MAX7325, | 
|  | MAX7326, | 
|  | MAX7327, | 
|  | }; | 
|  |  | 
|  | static uint64_t max732x_features[] = { | 
|  | [MAX7319] = GROUP_A(IO_8I) | INT_CAPS(INT_MERGED_MASK), | 
|  | [MAX7320] = GROUP_B(IO_8O), | 
|  | [MAX7321] = GROUP_A(IO_8P) | INT_CAPS(INT_NO_MASK), | 
|  | [MAX7322] = GROUP_A(IO_4I4O) | INT_CAPS(INT_MERGED_MASK), | 
|  | [MAX7323] = GROUP_A(IO_4P4O) | INT_CAPS(INT_INDEP_MASK), | 
|  | [MAX7324] = GROUP_A(IO_8I) | GROUP_B(IO_8O) | INT_CAPS(INT_MERGED_MASK), | 
|  | [MAX7325] = GROUP_A(IO_8P) | GROUP_B(IO_8O) | INT_CAPS(INT_NO_MASK), | 
|  | [MAX7326] = GROUP_A(IO_4I4O) | GROUP_B(IO_8O) | INT_CAPS(INT_MERGED_MASK), | 
|  | [MAX7327] = GROUP_A(IO_4P4O) | GROUP_B(IO_8O) | INT_CAPS(INT_NO_MASK), | 
|  | }; | 
|  |  | 
|  | static const struct i2c_device_id max732x_id[] = { | 
|  | { "max7319", MAX7319 }, | 
|  | { "max7320", MAX7320 }, | 
|  | { "max7321", MAX7321 }, | 
|  | { "max7322", MAX7322 }, | 
|  | { "max7323", MAX7323 }, | 
|  | { "max7324", MAX7324 }, | 
|  | { "max7325", MAX7325 }, | 
|  | { "max7326", MAX7326 }, | 
|  | { "max7327", MAX7327 }, | 
|  | { }, | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(i2c, max732x_id); | 
|  |  | 
|  | struct max732x_chip { | 
|  | struct gpio_chip gpio_chip; | 
|  |  | 
|  | struct i2c_client *client;	/* "main" client */ | 
|  | struct i2c_client *client_dummy; | 
|  | struct i2c_client *client_group_a; | 
|  | struct i2c_client *client_group_b; | 
|  |  | 
|  | unsigned int	mask_group_a; | 
|  | unsigned int	dir_input; | 
|  | unsigned int	dir_output; | 
|  |  | 
|  | struct mutex	lock; | 
|  | uint8_t		reg_out[2]; | 
|  |  | 
|  | #ifdef CONFIG_GPIO_MAX732X_IRQ | 
|  | struct mutex	irq_lock; | 
|  | int		irq_base; | 
|  | uint8_t		irq_mask; | 
|  | uint8_t		irq_mask_cur; | 
|  | uint8_t		irq_trig_raise; | 
|  | uint8_t		irq_trig_fall; | 
|  | uint8_t		irq_features; | 
|  | #endif | 
|  | }; | 
|  |  | 
|  | static int max732x_writeb(struct max732x_chip *chip, int group_a, uint8_t val) | 
|  | { | 
|  | struct i2c_client *client; | 
|  | int ret; | 
|  |  | 
|  | client = group_a ? chip->client_group_a : chip->client_group_b; | 
|  | ret = i2c_smbus_write_byte(client, val); | 
|  | if (ret < 0) { | 
|  | dev_err(&client->dev, "failed writing\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int max732x_readb(struct max732x_chip *chip, int group_a, uint8_t *val) | 
|  | { | 
|  | struct i2c_client *client; | 
|  | int ret; | 
|  |  | 
|  | client = group_a ? chip->client_group_a : chip->client_group_b; | 
|  | ret = i2c_smbus_read_byte(client); | 
|  | if (ret < 0) { | 
|  | dev_err(&client->dev, "failed reading\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | *val = (uint8_t)ret; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static inline int is_group_a(struct max732x_chip *chip, unsigned off) | 
|  | { | 
|  | return (1u << off) & chip->mask_group_a; | 
|  | } | 
|  |  | 
|  | static int max732x_gpio_get_value(struct gpio_chip *gc, unsigned off) | 
|  | { | 
|  | struct max732x_chip *chip; | 
|  | uint8_t reg_val; | 
|  | int ret; | 
|  |  | 
|  | chip = container_of(gc, struct max732x_chip, gpio_chip); | 
|  |  | 
|  | ret = max732x_readb(chip, is_group_a(chip, off), ®_val); | 
|  | if (ret < 0) | 
|  | return 0; | 
|  |  | 
|  | return reg_val & (1u << (off & 0x7)); | 
|  | } | 
|  |  | 
|  | static void max732x_gpio_set_value(struct gpio_chip *gc, unsigned off, int val) | 
|  | { | 
|  | struct max732x_chip *chip; | 
|  | uint8_t reg_out, mask = 1u << (off & 0x7); | 
|  | int ret; | 
|  |  | 
|  | chip = container_of(gc, struct max732x_chip, gpio_chip); | 
|  |  | 
|  | mutex_lock(&chip->lock); | 
|  |  | 
|  | reg_out = (off > 7) ? chip->reg_out[1] : chip->reg_out[0]; | 
|  | reg_out = (val) ? reg_out | mask : reg_out & ~mask; | 
|  |  | 
|  | ret = max732x_writeb(chip, is_group_a(chip, off), reg_out); | 
|  | if (ret < 0) | 
|  | goto out; | 
|  |  | 
|  | /* update the shadow register then */ | 
|  | if (off > 7) | 
|  | chip->reg_out[1] = reg_out; | 
|  | else | 
|  | chip->reg_out[0] = reg_out; | 
|  | out: | 
|  | mutex_unlock(&chip->lock); | 
|  | } | 
|  |  | 
|  | static int max732x_gpio_direction_input(struct gpio_chip *gc, unsigned off) | 
|  | { | 
|  | struct max732x_chip *chip; | 
|  | unsigned int mask = 1u << off; | 
|  |  | 
|  | chip = container_of(gc, struct max732x_chip, gpio_chip); | 
|  |  | 
|  | if ((mask & chip->dir_input) == 0) { | 
|  | dev_dbg(&chip->client->dev, "%s port %d is output only\n", | 
|  | chip->client->name, off); | 
|  | return -EACCES; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Open-drain pins must be set to high impedance (which is | 
|  | * equivalent to output-high) to be turned into an input. | 
|  | */ | 
|  | if ((mask & chip->dir_output)) | 
|  | max732x_gpio_set_value(gc, off, 1); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int max732x_gpio_direction_output(struct gpio_chip *gc, | 
|  | unsigned off, int val) | 
|  | { | 
|  | struct max732x_chip *chip; | 
|  | unsigned int mask = 1u << off; | 
|  |  | 
|  | chip = container_of(gc, struct max732x_chip, gpio_chip); | 
|  |  | 
|  | if ((mask & chip->dir_output) == 0) { | 
|  | dev_dbg(&chip->client->dev, "%s port %d is input only\n", | 
|  | chip->client->name, off); | 
|  | return -EACCES; | 
|  | } | 
|  |  | 
|  | max732x_gpio_set_value(gc, off, val); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_GPIO_MAX732X_IRQ | 
|  | static int max732x_writew(struct max732x_chip *chip, uint16_t val) | 
|  | { | 
|  | int ret; | 
|  |  | 
|  | val = cpu_to_le16(val); | 
|  |  | 
|  | ret = i2c_master_send(chip->client_group_a, (char *)&val, 2); | 
|  | if (ret < 0) { | 
|  | dev_err(&chip->client_group_a->dev, "failed writing\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int max732x_readw(struct max732x_chip *chip, uint16_t *val) | 
|  | { | 
|  | int ret; | 
|  |  | 
|  | ret = i2c_master_recv(chip->client_group_a, (char *)val, 2); | 
|  | if (ret < 0) { | 
|  | dev_err(&chip->client_group_a->dev, "failed reading\n"); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | *val = le16_to_cpu(*val); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void max732x_irq_update_mask(struct max732x_chip *chip) | 
|  | { | 
|  | uint16_t msg; | 
|  |  | 
|  | if (chip->irq_mask == chip->irq_mask_cur) | 
|  | return; | 
|  |  | 
|  | chip->irq_mask = chip->irq_mask_cur; | 
|  |  | 
|  | if (chip->irq_features == INT_NO_MASK) | 
|  | return; | 
|  |  | 
|  | mutex_lock(&chip->lock); | 
|  |  | 
|  | switch (chip->irq_features) { | 
|  | case INT_INDEP_MASK: | 
|  | msg = (chip->irq_mask << 8) | chip->reg_out[0]; | 
|  | max732x_writew(chip, msg); | 
|  | break; | 
|  |  | 
|  | case INT_MERGED_MASK: | 
|  | msg = chip->irq_mask | chip->reg_out[0]; | 
|  | max732x_writeb(chip, 1, (uint8_t)msg); | 
|  | break; | 
|  | } | 
|  |  | 
|  | mutex_unlock(&chip->lock); | 
|  | } | 
|  |  | 
|  | static int max732x_gpio_to_irq(struct gpio_chip *gc, unsigned off) | 
|  | { | 
|  | struct max732x_chip *chip; | 
|  |  | 
|  | chip = container_of(gc, struct max732x_chip, gpio_chip); | 
|  | return chip->irq_base + off; | 
|  | } | 
|  |  | 
|  | static void max732x_irq_mask(struct irq_data *d) | 
|  | { | 
|  | struct max732x_chip *chip = irq_data_get_irq_chip_data(d); | 
|  |  | 
|  | chip->irq_mask_cur &= ~(1 << (d->irq - chip->irq_base)); | 
|  | } | 
|  |  | 
|  | static void max732x_irq_unmask(struct irq_data *d) | 
|  | { | 
|  | struct max732x_chip *chip = irq_data_get_irq_chip_data(d); | 
|  |  | 
|  | chip->irq_mask_cur |= 1 << (d->irq - chip->irq_base); | 
|  | } | 
|  |  | 
|  | static void max732x_irq_bus_lock(struct irq_data *d) | 
|  | { | 
|  | struct max732x_chip *chip = irq_data_get_irq_chip_data(d); | 
|  |  | 
|  | mutex_lock(&chip->irq_lock); | 
|  | chip->irq_mask_cur = chip->irq_mask; | 
|  | } | 
|  |  | 
|  | static void max732x_irq_bus_sync_unlock(struct irq_data *d) | 
|  | { | 
|  | struct max732x_chip *chip = irq_data_get_irq_chip_data(d); | 
|  |  | 
|  | max732x_irq_update_mask(chip); | 
|  | mutex_unlock(&chip->irq_lock); | 
|  | } | 
|  |  | 
|  | static int max732x_irq_set_type(struct irq_data *d, unsigned int type) | 
|  | { | 
|  | struct max732x_chip *chip = irq_data_get_irq_chip_data(d); | 
|  | uint16_t off = d->irq - chip->irq_base; | 
|  | uint16_t mask = 1 << off; | 
|  |  | 
|  | if (!(mask & chip->dir_input)) { | 
|  | dev_dbg(&chip->client->dev, "%s port %d is output only\n", | 
|  | chip->client->name, off); | 
|  | return -EACCES; | 
|  | } | 
|  |  | 
|  | if (!(type & IRQ_TYPE_EDGE_BOTH)) { | 
|  | dev_err(&chip->client->dev, "irq %d: unsupported type %d\n", | 
|  | d->irq, type); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | if (type & IRQ_TYPE_EDGE_FALLING) | 
|  | chip->irq_trig_fall |= mask; | 
|  | else | 
|  | chip->irq_trig_fall &= ~mask; | 
|  |  | 
|  | if (type & IRQ_TYPE_EDGE_RISING) | 
|  | chip->irq_trig_raise |= mask; | 
|  | else | 
|  | chip->irq_trig_raise &= ~mask; | 
|  |  | 
|  | return max732x_gpio_direction_input(&chip->gpio_chip, off); | 
|  | } | 
|  |  | 
|  | static struct irq_chip max732x_irq_chip = { | 
|  | .name			= "max732x", | 
|  | .irq_mask		= max732x_irq_mask, | 
|  | .irq_unmask		= max732x_irq_unmask, | 
|  | .irq_bus_lock		= max732x_irq_bus_lock, | 
|  | .irq_bus_sync_unlock	= max732x_irq_bus_sync_unlock, | 
|  | .irq_set_type		= max732x_irq_set_type, | 
|  | }; | 
|  |  | 
|  | static uint8_t max732x_irq_pending(struct max732x_chip *chip) | 
|  | { | 
|  | uint8_t cur_stat; | 
|  | uint8_t old_stat; | 
|  | uint8_t trigger; | 
|  | uint8_t pending; | 
|  | uint16_t status; | 
|  | int ret; | 
|  |  | 
|  | ret = max732x_readw(chip, &status); | 
|  | if (ret) | 
|  | return 0; | 
|  |  | 
|  | trigger = status >> 8; | 
|  | trigger &= chip->irq_mask; | 
|  |  | 
|  | if (!trigger) | 
|  | return 0; | 
|  |  | 
|  | cur_stat = status & 0xFF; | 
|  | cur_stat &= chip->irq_mask; | 
|  |  | 
|  | old_stat = cur_stat ^ trigger; | 
|  |  | 
|  | pending = (old_stat & chip->irq_trig_fall) | | 
|  | (cur_stat & chip->irq_trig_raise); | 
|  | pending &= trigger; | 
|  |  | 
|  | return pending; | 
|  | } | 
|  |  | 
|  | static irqreturn_t max732x_irq_handler(int irq, void *devid) | 
|  | { | 
|  | struct max732x_chip *chip = devid; | 
|  | uint8_t pending; | 
|  | uint8_t level; | 
|  |  | 
|  | pending = max732x_irq_pending(chip); | 
|  |  | 
|  | if (!pending) | 
|  | return IRQ_HANDLED; | 
|  |  | 
|  | do { | 
|  | level = __ffs(pending); | 
|  | handle_nested_irq(level + chip->irq_base); | 
|  |  | 
|  | pending &= ~(1 << level); | 
|  | } while (pending); | 
|  |  | 
|  | return IRQ_HANDLED; | 
|  | } | 
|  |  | 
|  | static int max732x_irq_setup(struct max732x_chip *chip, | 
|  | const struct i2c_device_id *id) | 
|  | { | 
|  | struct i2c_client *client = chip->client; | 
|  | struct max732x_platform_data *pdata = client->dev.platform_data; | 
|  | int has_irq = max732x_features[id->driver_data] >> 32; | 
|  | int ret; | 
|  |  | 
|  | if (pdata->irq_base && has_irq != INT_NONE) { | 
|  | int lvl; | 
|  |  | 
|  | chip->irq_base = pdata->irq_base; | 
|  | chip->irq_features = has_irq; | 
|  | mutex_init(&chip->irq_lock); | 
|  |  | 
|  | for (lvl = 0; lvl < chip->gpio_chip.ngpio; lvl++) { | 
|  | int irq = lvl + chip->irq_base; | 
|  |  | 
|  | if (!(chip->dir_input & (1 << lvl))) | 
|  | continue; | 
|  |  | 
|  | irq_set_chip_data(irq, chip); | 
|  | irq_set_chip_and_handler(irq, &max732x_irq_chip, | 
|  | handle_edge_irq); | 
|  | irq_set_nested_thread(irq, 1); | 
|  | #ifdef CONFIG_ARM | 
|  | set_irq_flags(irq, IRQF_VALID); | 
|  | #else | 
|  | irq_set_noprobe(irq); | 
|  | #endif | 
|  | } | 
|  |  | 
|  | ret = request_threaded_irq(client->irq, | 
|  | NULL, | 
|  | max732x_irq_handler, | 
|  | IRQF_TRIGGER_FALLING | IRQF_ONESHOT, | 
|  | dev_name(&client->dev), chip); | 
|  | if (ret) { | 
|  | dev_err(&client->dev, "failed to request irq %d\n", | 
|  | client->irq); | 
|  | goto out_failed; | 
|  | } | 
|  |  | 
|  | chip->gpio_chip.to_irq = max732x_gpio_to_irq; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | out_failed: | 
|  | chip->irq_base = 0; | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void max732x_irq_teardown(struct max732x_chip *chip) | 
|  | { | 
|  | if (chip->irq_base) | 
|  | free_irq(chip->client->irq, chip); | 
|  | } | 
|  | #else /* CONFIG_GPIO_MAX732X_IRQ */ | 
|  | static int max732x_irq_setup(struct max732x_chip *chip, | 
|  | const struct i2c_device_id *id) | 
|  | { | 
|  | struct i2c_client *client = chip->client; | 
|  | struct max732x_platform_data *pdata = client->dev.platform_data; | 
|  | int has_irq = max732x_features[id->driver_data] >> 32; | 
|  |  | 
|  | if (pdata->irq_base && has_irq != INT_NONE) | 
|  | dev_warn(&client->dev, "interrupt support not compiled in\n"); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void max732x_irq_teardown(struct max732x_chip *chip) | 
|  | { | 
|  | } | 
|  | #endif | 
|  |  | 
|  | static int __devinit max732x_setup_gpio(struct max732x_chip *chip, | 
|  | const struct i2c_device_id *id, | 
|  | unsigned gpio_start) | 
|  | { | 
|  | struct gpio_chip *gc = &chip->gpio_chip; | 
|  | uint32_t id_data = (uint32_t)max732x_features[id->driver_data]; | 
|  | int i, port = 0; | 
|  |  | 
|  | for (i = 0; i < 16; i++, id_data >>= 2) { | 
|  | unsigned int mask = 1 << port; | 
|  |  | 
|  | switch (id_data & 0x3) { | 
|  | case PORT_OUTPUT: | 
|  | chip->dir_output |= mask; | 
|  | break; | 
|  | case PORT_INPUT: | 
|  | chip->dir_input |= mask; | 
|  | break; | 
|  | case PORT_OPENDRAIN: | 
|  | chip->dir_output |= mask; | 
|  | chip->dir_input |= mask; | 
|  | break; | 
|  | default: | 
|  | continue; | 
|  | } | 
|  |  | 
|  | if (i < 8) | 
|  | chip->mask_group_a |= mask; | 
|  | port++; | 
|  | } | 
|  |  | 
|  | if (chip->dir_input) | 
|  | gc->direction_input = max732x_gpio_direction_input; | 
|  | if (chip->dir_output) { | 
|  | gc->direction_output = max732x_gpio_direction_output; | 
|  | gc->set = max732x_gpio_set_value; | 
|  | } | 
|  | gc->get = max732x_gpio_get_value; | 
|  | gc->can_sleep = 1; | 
|  |  | 
|  | gc->base = gpio_start; | 
|  | gc->ngpio = port; | 
|  | gc->label = chip->client->name; | 
|  | gc->owner = THIS_MODULE; | 
|  |  | 
|  | return port; | 
|  | } | 
|  |  | 
|  | static int __devinit max732x_probe(struct i2c_client *client, | 
|  | const struct i2c_device_id *id) | 
|  | { | 
|  | struct max732x_platform_data *pdata; | 
|  | struct max732x_chip *chip; | 
|  | struct i2c_client *c; | 
|  | uint16_t addr_a, addr_b; | 
|  | int ret, nr_port; | 
|  |  | 
|  | pdata = client->dev.platform_data; | 
|  | if (pdata == NULL) { | 
|  | dev_dbg(&client->dev, "no platform data\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | chip = kzalloc(sizeof(struct max732x_chip), GFP_KERNEL); | 
|  | if (chip == NULL) | 
|  | return -ENOMEM; | 
|  | chip->client = client; | 
|  |  | 
|  | nr_port = max732x_setup_gpio(chip, id, pdata->gpio_base); | 
|  |  | 
|  | addr_a = (client->addr & 0x0f) | 0x60; | 
|  | addr_b = (client->addr & 0x0f) | 0x50; | 
|  |  | 
|  | switch (client->addr & 0x70) { | 
|  | case 0x60: | 
|  | chip->client_group_a = client; | 
|  | if (nr_port > 8) { | 
|  | c = i2c_new_dummy(client->adapter, addr_b); | 
|  | chip->client_group_b = chip->client_dummy = c; | 
|  | } | 
|  | break; | 
|  | case 0x50: | 
|  | chip->client_group_b = client; | 
|  | if (nr_port > 8) { | 
|  | c = i2c_new_dummy(client->adapter, addr_a); | 
|  | chip->client_group_a = chip->client_dummy = c; | 
|  | } | 
|  | break; | 
|  | default: | 
|  | dev_err(&client->dev, "invalid I2C address specified %02x\n", | 
|  | client->addr); | 
|  | ret = -EINVAL; | 
|  | goto out_failed; | 
|  | } | 
|  |  | 
|  | mutex_init(&chip->lock); | 
|  |  | 
|  | max732x_readb(chip, is_group_a(chip, 0), &chip->reg_out[0]); | 
|  | if (nr_port > 8) | 
|  | max732x_readb(chip, is_group_a(chip, 8), &chip->reg_out[1]); | 
|  |  | 
|  | ret = max732x_irq_setup(chip, id); | 
|  | if (ret) | 
|  | goto out_failed; | 
|  |  | 
|  | ret = gpiochip_add(&chip->gpio_chip); | 
|  | if (ret) | 
|  | goto out_failed; | 
|  |  | 
|  | if (pdata->setup) { | 
|  | ret = pdata->setup(client, chip->gpio_chip.base, | 
|  | chip->gpio_chip.ngpio, pdata->context); | 
|  | if (ret < 0) | 
|  | dev_warn(&client->dev, "setup failed, %d\n", ret); | 
|  | } | 
|  |  | 
|  | i2c_set_clientdata(client, chip); | 
|  | return 0; | 
|  |  | 
|  | out_failed: | 
|  | max732x_irq_teardown(chip); | 
|  | kfree(chip); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int __devexit max732x_remove(struct i2c_client *client) | 
|  | { | 
|  | struct max732x_platform_data *pdata = client->dev.platform_data; | 
|  | struct max732x_chip *chip = i2c_get_clientdata(client); | 
|  | int ret; | 
|  |  | 
|  | if (pdata->teardown) { | 
|  | ret = pdata->teardown(client, chip->gpio_chip.base, | 
|  | chip->gpio_chip.ngpio, pdata->context); | 
|  | if (ret < 0) { | 
|  | dev_err(&client->dev, "%s failed, %d\n", | 
|  | "teardown", ret); | 
|  | return ret; | 
|  | } | 
|  | } | 
|  |  | 
|  | ret = gpiochip_remove(&chip->gpio_chip); | 
|  | if (ret) { | 
|  | dev_err(&client->dev, "%s failed, %d\n", | 
|  | "gpiochip_remove()", ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | max732x_irq_teardown(chip); | 
|  |  | 
|  | /* unregister any dummy i2c_client */ | 
|  | if (chip->client_dummy) | 
|  | i2c_unregister_device(chip->client_dummy); | 
|  |  | 
|  | kfree(chip); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static struct i2c_driver max732x_driver = { | 
|  | .driver = { | 
|  | .name	= "max732x", | 
|  | .owner	= THIS_MODULE, | 
|  | }, | 
|  | .probe		= max732x_probe, | 
|  | .remove		= __devexit_p(max732x_remove), | 
|  | .id_table	= max732x_id, | 
|  | }; | 
|  |  | 
|  | static int __init max732x_init(void) | 
|  | { | 
|  | return i2c_add_driver(&max732x_driver); | 
|  | } | 
|  | /* register after i2c postcore initcall and before | 
|  | * subsys initcalls that may rely on these GPIOs | 
|  | */ | 
|  | subsys_initcall(max732x_init); | 
|  |  | 
|  | static void __exit max732x_exit(void) | 
|  | { | 
|  | i2c_del_driver(&max732x_driver); | 
|  | } | 
|  | module_exit(max732x_exit); | 
|  |  | 
|  | MODULE_AUTHOR("Eric Miao <eric.miao@marvell.com>"); | 
|  | MODULE_DESCRIPTION("GPIO expander driver for MAX732X"); | 
|  | MODULE_LICENSE("GPL"); |