| /* | 
 |  *  drivers/irqchip/irq-zx29.c | 
 |  * | 
 |  *  Copyright (C)  2015 ZTE-TSP | 
 |  * | 
 |  * This program is free software; you can redistribute it and/or modify | 
 |  * it under the terms of the GNU General Public License version 2 as | 
 |  * published by the Free Software Foundation. | 
 |  * | 
 |  * Interrupt architecture for the GIC: | 
 |  * | 
 |  * o There is one Interrupt Distributor, which receives interrupts | 
 |  *   from system devices and sends them to the Interrupt Controllers. | 
 |  * | 
 |  * o There is one CPU Interface per CPU, which sends interrupts sent | 
 |  *   by the Distributor, and interrupts generated locally, to the | 
 |  *   associated CPU. The base address of the CPU interface is usually | 
 |  *   aliased so that the same address points to different chips depending | 
 |  *   on the CPU it is accessed from. | 
 |  * | 
 |  * Note that IRQs 0-31 are special - they are local to each CPU. | 
 |  * As such, the enable set/clear, pending set/clear and active bit | 
 |  * registers are banked per-cpu for these sources. | 
 |  * | 
 |  * port from irq-gic.c to adapt zx297520v2 | 
 |  */ | 
 | #include <linux/init.h> | 
 | #include <linux/kernel.h> | 
 | #include <linux/err.h> | 
 | #include <linux/module.h> | 
 | #include <linux/list.h> | 
 | #include <linux/smp.h> | 
 | #include <linux/cpu.h> | 
 | #include <linux/cpu_pm.h> | 
 | #include <linux/cpumask.h> | 
 | #include <linux/io.h> | 
 | #include <linux/of.h> | 
 | #include <linux/of_address.h> | 
 | #include <linux/of_irq.h> | 
 | #include <linux/irq.h> | 
 | #include <linux/irqdomain.h> | 
 | #include <linux/interrupt.h> | 
 | #include <linux/percpu.h> | 
 | #include <linux/slab.h> | 
 | #include <linux/delay.h> | 
 |  | 
 | #include <asm/irq.h> | 
 | #include <asm/exception.h> | 
 | #include <asm/smp_plat.h> | 
 |  | 
 | #include <mach/iomap.h> | 
 | #include <mach/board.h> | 
 | #include <mach/pcu.h> | 
 | #include <linux/wakelock.h> | 
 | #include "irqchip.h" | 
 |  | 
 | /* user will not see pcu hardware */ | 
 | #define	NEW_IRQ_TYPE_SUPPORT	1	 | 
 |  | 
 | #if NEW_LINUX_FRAME	 | 
 | #include <linux/irqchip/chained_irq.h> | 
 | #include <linux/irqchip/arm-gic.h> | 
 | #else | 
 | #include <asm/hardware/gic.h> | 
 | #include <asm/mach/irq.h> | 
 | #define ARRAYSIZE(a)		(sizeof(a) / sizeof(a[0])) | 
 | extern bool pm_get_wakeup_count(unsigned int *count, bool block); | 
 | extern void zx_pm_wakeup_irq_timeout(void); | 
 | #ifdef CONFIG_ARCH_ZX297520V2 | 
 | static const u32 wakeup_int_cfg[] = { | 
 | 	RTC_ALARM_INT, | 
 | 	RTC_TIMER_INT, | 
 | 	KEYPAD_INT, | 
 | 	ICP_PS2AP_INT, | 
 | 	ICP_M02AP_INT, | 
 | /*	AP_TIMER1_INT,*/ | 
 | 	AP_TIMER2_INT, | 
 | 	SPCU_PW_INT, | 
 | 	USB_POWERDWN_UP_INT, | 
 | 	USB_POWERDWN_DOWN_INT, | 
 | 	HSIC_POWERDWN_UP_INT, | 
 | 	HSIC_POWERDWN_DOWN_INT, | 
 | 	EX8IN1_INT, | 
 | 	EX0_INT, | 
 | 	EX1_INT, | 
 | 	EX2_INT, | 
 | 	EX3_INT, | 
 | 	EX4_INT, | 
 | 	EX5_INT, | 
 | 	EX6_INT, | 
 | 	EX7_INT, | 
 | 	SD1_DATA1_INT, | 
 | 	UART0_CTS_INT, | 
 | 	SD0_DATA1_INT, | 
 | 	GMAC_INT, | 
 | }; | 
 | #elif CONFIG_ARCH_ZX297520V3 | 
 | static const u32 wakeup_int_cfg[] = { | 
 | #ifndef CONFIG_ARCH_ZX297520V3_CAP | 
 | 	RTC_ALARM_INT, | 
 | 	RTC_TIMER_INT, | 
 | 	KEYPAD_INT, | 
 | 	ICP_PHY2PS_INT, | 
 | 	ICP_M02PS_INT, | 
 | 	PS_TIMER1_INT, | 
 | 	PS_RM_TIMER_INT, | 
 | 	SPCU_PW_INT, | 
 | 	USB_POWERDWN_UP_INT, | 
 | 	USB_POWERDWN_DOWN_INT, | 
 | 	HSIC_POWERDWN_UP_INT, | 
 | 	HSIC_POWERDWN_DOWN_INT, | 
 | 	EX8IN1_INT, | 
 | 	EX0_INT, | 
 | 	EX1_INT, | 
 | 	EX2_INT, | 
 | 	EX3_INT, | 
 | 	EX4_INT, | 
 | 	EX5_INT, | 
 | 	EX6_INT, | 
 | 	EX7_INT, | 
 | 	TD_LPM_TIMER_IND3_INT, | 
 | 	TD_LPM_FRM_INT, | 
 | 	FRM_ARM_INT, | 
 | 	LTE_LPM_TIMER2_INT, | 
 | 	LTE_LPM_TIMER4_INT, | 
 | 	LTE_LPM_TIMER5_INT, | 
 | 	GSM_LPM_INT1_INT, | 
 | 	WD_LPM_TIMER4_INT, | 
 | 	WD_FRAME_INT, | 
 | 	SD1_DATA1_INT, | 
 | 	UART0_RXD_INT, | 
 | 	PS_TIMER2_INT, | 
 | 	ICP_AP2PS_INT, | 
 | 	SD0_DATA1_INT, | 
 | 	TD_LPM_TIMER_IND2_INT, | 
 | 	LTE_LPM_TIMER1_INT, | 
 | 	WD_LPM_TIMER3_INT, | 
 | #else | 
 | 	RTC_ALARM_INT, | 
 | 	RTC_TIMER_INT, | 
 | 	KEYPAD_INT, | 
 | 	ICP_PS2AP_INT, | 
 | 	ICP_M02AP_INT, | 
 | 	ICP_PHY2AP_INT, | 
 | /*	AP_TIMER1_INT,*/ | 
 | /*	AP_TIMER2_INT,*/ | 
 | 	SPCU_PW_INT, | 
 | 	USB_POWERDWN_UP_INT, | 
 | 	USB_POWERDWN_DOWN_INT, | 
 | 	HSIC_POWERDWN_UP_INT, | 
 | 	HSIC_POWERDWN_DOWN_INT, | 
 | 	EX8IN1_INT, | 
 | 	EX0_INT, | 
 | 	EX1_INT, | 
 | 	EX2_INT, | 
 | 	EX3_INT, | 
 | 	EX4_INT, | 
 | 	EX5_INT, | 
 | 	EX6_INT, | 
 | 	EX7_INT, | 
 | 	FRM_ARM_INT, | 
 | 	LTE_LPM_TIMER5_INT, | 
 | 	WD_FRAME_INT, | 
 | 	SD1_DATA1_INT, | 
 | 	UART0_RXD_INT, | 
 | 	SD0_DATA1_INT, | 
 | 	GMAC_INT, | 
 | 	GMACPHY_WAKE_INT, | 
 | 	GMACPHY_INT, | 
 | #endif | 
 | }; | 
 | #endif | 
 | static u8 wakeup_int[NR_SOC_IRQS - GIC_SPI_START]; | 
 | static bool is_wakeup_interrupt(u32 irq_num) | 
 | { | 
 | 	if (irq_num < (NR_SOC_IRQS) && wakeup_int[irq_num - GIC_SPI_START]) | 
 | 			return 1; | 
 | 		else | 
 | 	return 0; | 
 | } | 
 |  | 
 | #ifdef CONFIG_MULTI_IRQ_HANDLER | 
 | void __init set_handle_irq(void (*handle_irq)(struct pt_regs *)) | 
 | { | 
 | 	if (handle_arch_irq) | 
 | 		return; | 
 |  | 
 | 	handle_arch_irq = handle_irq; | 
 | } | 
 | #endif | 
 |  | 
 | #endif | 
 |  | 
 | #if 0 | 
 | union gic_base { | 
 | 	void __iomem *common_base; | 
 | 	void __percpu __iomem **percpu_base; | 
 | }; | 
 |  | 
 | struct gic_chip_data { | 
 | 	union gic_base dist_base; | 
 | 	union gic_base cpu_base; | 
 | #ifdef CONFIG_CPU_PM | 
 | 	u32 saved_spi_enable[DIV_ROUND_UP(1020, 32)]; | 
 | 	u32 saved_spi_conf[DIV_ROUND_UP(1020, 16)]; | 
 | 	u32 saved_spi_target[DIV_ROUND_UP(1020, 4)]; | 
 | 	u32 __percpu *saved_ppi_enable; | 
 | 	u32 __percpu *saved_ppi_conf; | 
 | #endif | 
 | 	struct irq_domain *domain; | 
 | 	unsigned int gic_irqs; | 
 | #ifdef CONFIG_GIC_NON_BANKED | 
 | 	void __iomem *(*get_base)(union gic_base *); | 
 | #endif | 
 | }; | 
 | #endif | 
 |  | 
 | //#define CONFIG_INT_DEBUG | 
 |  | 
 | #ifdef CONFIG_INT_DEBUG | 
 | #pragma GCC optimize("O0") | 
 |  | 
 | extern unsigned int test_timer_read( void ); | 
 |  | 
 | typedef struct  | 
 | { | 
 |   unsigned int int_trace; | 
 |   unsigned int int_time; | 
 | }int_trace_t; | 
 |  | 
 | volatile int_trace_t int_enter_view[1000]; | 
 | volatile unsigned int int_enter_index=0; | 
 | volatile int_trace_t int_end_view[1000]; | 
 | volatile unsigned int int_end_index=0; | 
 |  | 
 | #endif  | 
 |  | 
 | extern int get_init_irq_flag(void); | 
 |  | 
 |  | 
 | static DEFINE_RAW_SPINLOCK(irq_controller_lock); | 
 |  | 
 | /* | 
 |  * The GIC mapping of CPU interfaces does not necessarily match | 
 |  * the logical CPU numbering.  Let's use a mapping as returned | 
 |  * by the GIC itself. | 
 |  */ | 
 | #define NR_GIC_CPU_IF 8 | 
 | static u8 gic_cpu_map[NR_GIC_CPU_IF] __read_mostly; | 
 |  | 
 | /* | 
 |  * Supported arch specific GIC irq extension. | 
 |  * Default make them NULL. | 
 |  */ | 
 | struct irq_chip gic_arch_extn = { | 
 | 	.irq_eoi	= NULL, | 
 | 	.irq_mask	= NULL, | 
 | 	.irq_unmask	= NULL, | 
 | 	.irq_retrigger	= NULL, | 
 | 	.irq_set_type	= NULL, | 
 | 	.irq_set_wake	= NULL, | 
 | }; | 
 |  | 
 | #ifndef MAX_GIC_NR | 
 | #define MAX_GIC_NR  1 | 
 | #endif | 
 |  | 
 | static struct gic_chip_data gic_data[MAX_GIC_NR] __read_mostly; | 
 |  | 
 | #ifdef CONFIG_GIC_NON_BANKED | 
 | static void __iomem *gic_get_percpu_base(union gic_base *base) | 
 | { | 
 | 	return *__this_cpu_ptr(base->percpu_base); | 
 | } | 
 |  | 
 | static void __iomem *gic_get_common_base(union gic_base *base) | 
 | { | 
 | 	return base->common_base; | 
 | } | 
 |  | 
 | static inline void __iomem *gic_data_dist_base(struct gic_chip_data *data) | 
 | { | 
 | 	return data->get_base(&data->dist_base); | 
 | } | 
 |  | 
 | static inline void __iomem *gic_data_cpu_base(struct gic_chip_data *data) | 
 | { | 
 | 	return data->get_base(&data->cpu_base); | 
 | } | 
 |  | 
 | static inline void gic_set_base_accessor(struct gic_chip_data *data, | 
 | 					 void __iomem *(*f)(union gic_base *)) | 
 | { | 
 | 	data->get_base = f; | 
 | } | 
 | #else | 
 | #define gic_data_dist_base(d)	((d)->dist_base.common_base) | 
 | #define gic_data_cpu_base(d)	((d)->cpu_base.common_base) | 
 | #define gic_set_base_accessor(d, f) | 
 | #endif | 
 |  | 
 | void __iomem *base_testtt=NULL; | 
 |  | 
 | static inline void __iomem *gic_dist_base(struct irq_data *d) | 
 | { | 
 | 	struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d); | 
 | 	base_testtt = gic_data_dist_base(gic_data); | 
 | 	return gic_data_dist_base(gic_data); | 
 | } | 
 |  | 
 | static inline void __iomem *gic_cpu_base(struct irq_data *d) | 
 | { | 
 | 	struct gic_chip_data *gic_data = irq_data_get_irq_chip_data(d); | 
 | 	return gic_data_cpu_base(gic_data); | 
 | } | 
 |  | 
 | static inline unsigned int gic_irq(struct irq_data *d) | 
 | { | 
 | 	return d->hwirq; | 
 | } | 
 |  | 
 | /* | 
 |  * Routines to acknowledge, disable and enable interrupts | 
 |  */ | 
 | static void gic_mask_irq(struct irq_data *d) | 
 | { | 
 | 	u32 mask = 1 << (gic_irq(d) % 32); | 
 |  | 
 | 	raw_spin_lock(&irq_controller_lock); | 
 | 	writel_relaxed(mask, gic_dist_base(d) + GIC_DIST_ENABLE_CLEAR + (gic_irq(d) / 32) * 4); | 
 | 	if (gic_arch_extn.irq_mask) | 
 | 		gic_arch_extn.irq_mask(d); | 
 | 	raw_spin_unlock(&irq_controller_lock); | 
 | } | 
 |  | 
 | static void gic_unmask_irq(struct irq_data *d) | 
 | { | 
 | 	u32 mask = 1 << (gic_irq(d) % 32); | 
 |  | 
 | 	raw_spin_lock(&irq_controller_lock); | 
 | 	if (gic_arch_extn.irq_unmask) | 
 | 		gic_arch_extn.irq_unmask(d); | 
 | 	writel_relaxed(mask, gic_dist_base(d) + GIC_DIST_ENABLE_SET + (gic_irq(d) / 32) * 4); | 
 | 	raw_spin_unlock(&irq_controller_lock); | 
 | } | 
 |  | 
 | static void gic_eoi_irq(struct irq_data *d) | 
 | { | 
 | 	if (gic_arch_extn.irq_eoi) { | 
 | 		raw_spin_lock(&irq_controller_lock); | 
 | 		gic_arch_extn.irq_eoi(d); | 
 | 		raw_spin_unlock(&irq_controller_lock); | 
 | 	} | 
 |  | 
 | 	writel_relaxed(gic_irq(d), gic_cpu_base(d) + GIC_CPU_EOI); | 
 | 		 | 
 | 	#ifdef CONFIG_INT_DEBUG | 
 | 		int_end_view[int_end_index].int_trace=gic_irq(d); | 
 | 		int_end_view[int_end_index].int_time=cpu_clock(0) >> 10; | 
 | 		int_end_index++; | 
 | 		if(int_end_index==1000) | 
 | 		   int_end_index=0; | 
 | 	#endif | 
 | } | 
 |  | 
 |  int gic_set_type(struct irq_data *d, unsigned int type) | 
 | { | 
 | 	void __iomem *base = gic_dist_base(d); | 
 | 	unsigned int gicirq = gic_irq(d); | 
 | 	u32 enablemask = 1 << (gicirq % 32); | 
 | 	u32 enableoff = (gicirq / 32) * 4; | 
 | 	u32 confmask = 0x2 << ((gicirq % 16) * 2); | 
 | 	u32 confoff = (gicirq / 16) * 4; | 
 | 	bool enabled = false; | 
 | 	u32 val; | 
 |  | 
 | 	/* Interrupt configuration for SGIs and PPIs can't be changed */ | 
 | 	if (gicirq < 32) | 
 | 		return -EINVAL; | 
 |  | 
 | 	/*if (type != IRQ_TYPE_LEVEL_HIGH && type != IRQ_TYPE_EDGE_RISING) | 
 | 		return -EINVAL;*/ | 
 |  | 
 | 	raw_spin_lock(&irq_controller_lock); | 
 |  | 
 | 	/*if (gic_arch_extn.irq_set_type)                        // move to after irq disabled | 
 | 		gic_arch_extn.irq_set_type(d, type);*/ | 
 | 		 | 
 | #if NEW_IRQ_TYPE_SUPPORT | 
 | 	/* when the line pass through pcu, we set gic high_level. */ | 
 | 	if(get_init_irq_flag()) | 
 | 	{ | 
 | 		if(!pcu_set_irq_type(gic_irq(d), type)) | 
 | 			type = IRQ_TYPE_LEVEL_HIGH; | 
 | 	} | 
 |  | 
 | #endif | 
 |  | 
 | 	val = readl_relaxed(base + GIC_DIST_CONFIG + confoff); | 
 | 	if ((type == IRQ_TYPE_LEVEL_HIGH)||(type == IRQ_TYPE_LEVEL_LOW)) | 
 | 		val &= ~confmask; | 
 | 	else if ((type == IRQ_TYPE_EDGE_RISING)||(type == IRQ_TYPE_EDGE_FALLING)) | 
 | 		val |= confmask; | 
 |  | 
 | 	/* | 
 | 	 * As recommended by the spec, disable the interrupt which has enabled before changing | 
 | 	 * the configuration | 
 | 	 */ | 
 | 	if (readl_relaxed(base + GIC_DIST_ENABLE_SET + enableoff) & enablemask) { | 
 | 		writel_relaxed(enablemask, base + GIC_DIST_ENABLE_CLEAR + enableoff); | 
 | 		enabled = true; | 
 | 	} | 
 |  | 
 | 	if (gic_arch_extn.irq_set_type)                            //move to  here would be more safe   | 
 | 		gic_arch_extn.irq_set_type(d, type); | 
 | 	 | 
 | 	writel_relaxed(val, base + GIC_DIST_CONFIG + confoff); | 
 |  | 
 | 	if (enabled) | 
 | 		writel_relaxed(enablemask, base + GIC_DIST_ENABLE_SET + enableoff); | 
 |  | 
 | 	raw_spin_unlock(&irq_controller_lock); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int gic_retrigger(struct irq_data *d) | 
 | { | 
 | 	if (gic_arch_extn.irq_retrigger) | 
 | 		return gic_arch_extn.irq_retrigger(d); | 
 |  | 
 | 	/* the genirq layer expects 0 if we can't retrigger in hardware */ | 
 | 	return 0; | 
 | } | 
 |  | 
 | #ifdef CONFIG_SMP | 
 | static int gic_set_affinity(struct irq_data *d, const struct cpumask *mask_val, | 
 | 			    bool force) | 
 | { | 
 | 	void __iomem *reg = gic_dist_base(d) + GIC_DIST_TARGET + (gic_irq(d) & ~3); | 
 | 	unsigned int cpu, shift = (gic_irq(d) % 4) * 8; | 
 | 	u32 val, mask, bit; | 
 |  | 
 | 	if (!force) | 
 | 		cpu = cpumask_any_and(mask_val, cpu_online_mask); | 
 | 	else | 
 | 		cpu = cpumask_first(mask_val); | 
 |  | 
 | 	if (cpu >= NR_GIC_CPU_IF || cpu >= nr_cpu_ids) | 
 | 		return -EINVAL; | 
 |  | 
 | 	raw_spin_lock(&irq_controller_lock); | 
 | 	mask = 0xff << shift; | 
 | 	bit = gic_cpu_map[cpu] << shift; | 
 | 	val = readl_relaxed(reg) & ~mask; | 
 | 	writel_relaxed(val | bit, reg); | 
 | 	raw_spin_unlock(&irq_controller_lock); | 
 |  | 
 | 	return IRQ_SET_MASK_OK; | 
 | } | 
 | #endif | 
 |  | 
 | #ifdef CONFIG_PM | 
 | static int gic_set_wake(struct irq_data *d, unsigned int on) | 
 | { | 
 | 	int ret = -ENXIO; | 
 |  | 
 | 	if (gic_arch_extn.irq_set_wake) | 
 | 		ret = gic_arch_extn.irq_set_wake(d, on); | 
 |  | 
 | 	return ret; | 
 | } | 
 |  | 
 | #else | 
 | #define gic_set_wake	NULL | 
 | #endif | 
 |  | 
 | asmlinkage void __exception_irq_entry gic_handle_irq(struct pt_regs *regs) | 
 | { | 
 | 	u32 irqstat, irqnr; | 
 | 	struct gic_chip_data *gic = &gic_data[0]; | 
 | 	void __iomem *cpu_base = gic_data_cpu_base(gic); | 
 |  | 
 | 	do { | 
 | 		irqstat = readl_relaxed(cpu_base + GIC_CPU_INTACK); | 
 | 		irqnr = irqstat & 0x3ff;	//zxp ~0x1c00; | 
 |  | 
 | 	#ifdef CONFIG_INT_DEBUG | 
 | 	if(irqnr<1021){ | 
 | 		int_enter_view[int_enter_index].int_trace=irqnr; | 
 | 		int_enter_view[int_enter_index].int_time=cpu_clock(0) >> 10; | 
 | 		int_enter_index++; | 
 | 		if(int_enter_index==1000) | 
 | 		   int_enter_index=0; | 
 |   	}	 | 
 | 	#endif | 
 | 	 | 
 | 		if (likely(irqnr > 15 && irqnr < 1021)) { | 
 | 			irqnr = irq_find_mapping(gic->domain, irqnr); | 
 | 			handle_IRQ(irqnr, regs); | 
 | #if NEW_IRQ_TYPE_SUPPORT | 
 | 			/* when the line pass through pcu, we clr pcu int pending. */ | 
 | 			pcu_clr_irq_pending(irqnr); | 
 | #endif | 
 | 			continue; | 
 | 		} | 
 | 		if (irqnr < 16) { | 
 | 			writel_relaxed(irqstat, cpu_base + GIC_CPU_EOI); | 
 | #ifdef CONFIG_SMP | 
 | 			handle_IPI(irqnr, regs); | 
 | #endif | 
 | 			continue; | 
 | 		} | 
 | 		break; | 
 | 	} while (1); | 
 | } | 
 |  | 
 | static void gic_handle_cascade_irq(unsigned int irq, struct irq_desc *desc) | 
 | { | 
 | 	struct gic_chip_data *chip_data = irq_get_handler_data(irq); | 
 | 	struct irq_chip *chip = irq_get_chip(irq); | 
 | 	unsigned int cascade_irq, gic_irq; | 
 | 	unsigned long status; | 
 |  | 
 | 	if(chip_data==NULL) | 
 | 		return; | 
 | 	if(chip==NULL) | 
 | 		return; | 
 | 	 | 
 | 	chained_irq_enter(chip, desc); | 
 |  | 
 | 	raw_spin_lock(&irq_controller_lock); | 
 | 	status = readl_relaxed(gic_data_cpu_base(chip_data) + GIC_CPU_INTACK); | 
 | 	raw_spin_unlock(&irq_controller_lock); | 
 |  | 
 | 	gic_irq = (status & 0x3ff); | 
 | 	if (gic_irq == 1023) | 
 | 		goto out; | 
 |  | 
 | 	cascade_irq = irq_find_mapping(chip_data->domain, gic_irq); | 
 | 	if (unlikely(gic_irq < 32 || gic_irq > 1020)) | 
 | 		handle_bad_irq(cascade_irq, desc); | 
 | 	else | 
 | 		generic_handle_irq(cascade_irq); | 
 |  | 
 |  out: | 
 | 	chained_irq_exit(chip, desc); | 
 | } | 
 |  | 
 | static struct irq_chip gic_chip = { | 
 | 	.name			= "GIC", | 
 | 	.irq_mask		= gic_mask_irq, | 
 | 	.irq_unmask		= gic_unmask_irq, | 
 | 	.irq_eoi		= gic_eoi_irq, | 
 | 	.irq_set_type		= gic_set_type, | 
 | 	.irq_retrigger		= gic_retrigger, | 
 | #ifdef CONFIG_SMP | 
 | 	.irq_set_affinity	= gic_set_affinity, | 
 | #endif | 
 | 	.irq_set_wake		= gic_set_wake, | 
 | }; | 
 |  | 
 | void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq) | 
 | { | 
 | 	if (gic_nr >= MAX_GIC_NR) | 
 | 		BUG(); | 
 | 	if (irq_set_handler_data(irq, &gic_data[gic_nr]) != 0) | 
 | 		BUG(); | 
 | 	irq_set_chained_handler(irq, gic_handle_cascade_irq); | 
 | } | 
 |  | 
 | static u8 gic_get_cpumask(struct gic_chip_data *gic) | 
 | { | 
 | 	void __iomem *base = gic_data_dist_base(gic); | 
 | 	u32 mask, i; | 
 |  | 
 | 	for (i = mask = 0; i < 32; i += 4) { | 
 | 		mask = readl_relaxed(base + GIC_DIST_TARGET + i); | 
 | 		mask |= mask >> 16; | 
 | 		mask |= mask >> 8; | 
 | 		if (mask) | 
 | 			break; | 
 | 	} | 
 |  | 
 | 	if (!mask) | 
 | 		pr_crit("GIC CPU mask not found - kernel will fail to boot.\n"); | 
 |  | 
 | 	return mask; | 
 | } | 
 |  | 
 | static void __init gic_dist_init(struct gic_chip_data *gic) | 
 | { | 
 | 	unsigned int i; | 
 | 	/*u32 cpumask;*/ | 
 | 	unsigned int gic_irqs = gic->gic_irqs; | 
 | 	void __iomem *base = gic_data_dist_base(gic); | 
 |  | 
 | 	writel_relaxed(0, base + GIC_DIST_CTRL); | 
 |  | 
 | 	/* | 
 | 	 * Set all global interrupts to be level triggered, active low. | 
 | 	 */ | 
 | 	for (i = 32; i < gic_irqs; i += 16) | 
 | 		writel_relaxed(0, base + GIC_DIST_CONFIG + i * 4 / 16); | 
 |  | 
 | 	/* | 
 | 	 * Set all global interrupts to this CPU only. | 
 | 	 */ | 
 |   /*  cpumask = gic_get_cpumask(gic); | 
 |     cpumask |= cpumask << 8; | 
 |     cpumask |= cpumask << 16; | 
 |     for (i = 32; i < gic_irqs; i += 4) | 
 |     { | 
 |         writel_relaxed(cpumask, base + GIC_DIST_TARGET + i * 4 / 4); | 
 |     }*/ | 
 |  | 
 | 	/* | 
 | 	 * Set priority on all global interrupts. | 
 | 	 */ | 
 | 	for (i = 32; i < gic_irqs; i += 4) | 
 | 		writel_relaxed(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4); | 
 |  | 
 | 	/* | 
 | 	 * Disable all interrupts.  Leave the PPI and SGIs alone | 
 | 	 * as these enables are banked registers. | 
 | 	 */ | 
 | 	for (i = 32; i < gic_irqs; i += 32) | 
 | 		writel_relaxed(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32); | 
 |  | 
 | 	writel_relaxed(1, base + GIC_DIST_CTRL); | 
 | } | 
 | #ifdef CONFIG_ARCH_ZX297520V2 | 
 | #else | 
 | /* for gic500 */ | 
 | #define GICR_WAKER					0x0014 | 
 | #define GICR_WAKER_ProcessorSleep	(1U << 1) | 
 | #define GICR_WAKER_ChildrenAsleep	(1U << 2) | 
 |  | 
 | static void gic_enable_redist(bool enable) | 
 | { | 
 | 	void __iomem *rbase = GIC_REDIST_BASE; | 
 | 	u32 count = 1000000;	/* 1s! */ | 
 | 	u32 val; | 
 |  | 
 | //	rbase = gic_data_rdist_rd_base(); | 
 |  | 
 | 	val = readl_relaxed(rbase + GICR_WAKER); | 
 | 	if (enable) | 
 | 		/* Wake up this CPU redistributor */ | 
 | 		val &= ~GICR_WAKER_ProcessorSleep; | 
 | 	else | 
 | 		val |= GICR_WAKER_ProcessorSleep; | 
 | 	writel_relaxed(val, rbase + GICR_WAKER); | 
 |  | 
 | 	if (!enable) {		/* Check that GICR_WAKER is writeable */ | 
 | 		val = readl_relaxed(rbase + GICR_WAKER); | 
 | 		if (!(val & GICR_WAKER_ProcessorSleep)) | 
 | 			return;	/* No PM support in this redistributor */ | 
 | 	} | 
 |  | 
 | 	while (count--) { | 
 | 		val = readl_relaxed(rbase + GICR_WAKER); | 
 | 		if (enable ^ (val & GICR_WAKER_ChildrenAsleep)) | 
 | 			break; | 
 | 		cpu_relax(); | 
 | 		udelay(1); | 
 | 	}; | 
 | 	if (!count) | 
 | 		pr_err("redistributor failed to %s...\n", | 
 | 				   enable ? "wakeup" : "sleep"); | 
 | } | 
 | #endif | 
 |  | 
 | static void __cpuinit gic_cpu_init(struct gic_chip_data *gic) | 
 | { | 
 | 	void __iomem *dist_base = gic_data_dist_base(gic); | 
 | 	void __iomem *base = gic_data_cpu_base(gic); | 
 | 	unsigned int /*cpu_mask, */cpu = smp_processor_id(); | 
 | 	int i; | 
 |  | 
 | 	/* | 
 | 	 * Get what the GIC says our CPU mask is. | 
 | 	 */ | 
 |     BUG_ON(cpu >= NR_GIC_CPU_IF); | 
 | #if 0	 | 
 | 	cpu_mask = gic_get_cpumask(gic); | 
 | 	gic_cpu_map[cpu] = cpu_mask; | 
 |  | 
 | 	/* | 
 | 	 * Clear our mask from the other map entries in case they're | 
 | 	 * still undefined. | 
 | 	 */ | 
 | 	for (i = 0; i < NR_GIC_CPU_IF; i++) | 
 | 		if (i != cpu) | 
 | 			gic_cpu_map[i] &= ~cpu_mask; | 
 | #endif  | 
 |  | 
 | 	/* | 
 | 	 * Deal with the banked PPI and SGI interrupts - disable all | 
 | 	 * PPI interrupts, ensure all SGI interrupts are enabled. | 
 | 	 */ | 
 | 	writel_relaxed(0xffff0000, dist_base + GIC_DIST_ENABLE_CLEAR); | 
 | 	writel_relaxed(0x0000ffff, dist_base + GIC_DIST_ENABLE_SET); | 
 |  | 
 | 	/* | 
 | 	 * Set priority on PPI and SGI interrupts | 
 | 	 */ | 
 | 	for (i = 0; i < 32; i += 4) | 
 | 		writel_relaxed(0xa0a0a0a0, dist_base + GIC_DIST_PRI + i * 4 / 4); | 
 |  | 
 | 	writel_relaxed(0xf0, base + GIC_CPU_PRIMASK); | 
 | #ifdef CONFIG_ARCH_ZX297520V2 | 
 | #else | 
 | 	gic_enable_redist(true); | 
 | #endif | 
 | 	writel_relaxed(1, base + GIC_CPU_CTRL); | 
 | } | 
 |  | 
 | void gic_cpu_if_down(void) | 
 | { | 
 | 	void __iomem *cpu_base = gic_data_cpu_base(&gic_data[0]); | 
 | 	writel_relaxed(0, cpu_base + GIC_CPU_CTRL); | 
 | } | 
 |  | 
 | #ifdef CONFIG_CPU_PM | 
 | /* | 
 |  * Saves the GIC distributor registers during suspend or idle.  Must be called | 
 |  * with interrupts disabled but before powering down the GIC.  After calling | 
 |  * this function, no interrupts will be delivered by the GIC, and another | 
 |  * platform-specific wakeup source must be enabled. | 
 |  */ | 
 | static void gic_dist_save(unsigned int gic_nr) | 
 | { | 
 | 	unsigned int gic_irqs; | 
 | 	void __iomem *dist_base; | 
 | 	int i; | 
 |  | 
 | 	if (gic_nr >= MAX_GIC_NR) | 
 | 		BUG(); | 
 |  | 
 | 	gic_irqs = gic_data[gic_nr].gic_irqs; | 
 | 	dist_base = gic_data_dist_base(&gic_data[gic_nr]); | 
 |  | 
 | 	if (!dist_base) | 
 | 		return; | 
 |  | 
 | 	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 16); i++) | 
 | 		gic_data[gic_nr].saved_spi_conf[i] = | 
 | 			readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4); | 
 |  | 
 | 	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++) | 
 | 		gic_data[gic_nr].saved_spi_target[i] = | 
 | 			readl_relaxed(dist_base + GIC_DIST_TARGET + i * 4); | 
 |  | 
 | 	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++) | 
 | 		gic_data[gic_nr].saved_spi_enable[i] = | 
 | 			readl_relaxed(dist_base + GIC_DIST_ENABLE_SET + i * 4); | 
 | } | 
 |  | 
 | /* | 
 |  * Restores the GIC distributor registers during resume or when coming out of | 
 |  * idle.  Must be called before enabling interrupts.  If a level interrupt | 
 |  * that occured while the GIC was suspended is still present, it will be | 
 |  * handled normally, but any edge interrupts that occured will not be seen by | 
 |  * the GIC and need to be handled by the platform-specific wakeup source. | 
 |  */ | 
 | static void gic_dist_restore(unsigned int gic_nr) | 
 | { | 
 | 	unsigned int gic_irqs; | 
 | 	unsigned int i; | 
 | 	void __iomem *dist_base; | 
 |  | 
 | 	if (gic_nr >= MAX_GIC_NR) | 
 | 		BUG(); | 
 |  | 
 | 	gic_irqs = gic_data[gic_nr].gic_irqs; | 
 | 	dist_base = gic_data_dist_base(&gic_data[gic_nr]); | 
 |  | 
 | 	if (!dist_base) | 
 | 		return; | 
 |  | 
 | 	writel_relaxed(0, dist_base + GIC_DIST_CTRL); | 
 |  | 
 | 	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 16); i++) | 
 | 		writel_relaxed(gic_data[gic_nr].saved_spi_conf[i], | 
 | 			dist_base + GIC_DIST_CONFIG + i * 4); | 
 |  | 
 | 	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++) | 
 | 		writel_relaxed(0xa0a0a0a0, | 
 | 			dist_base + GIC_DIST_PRI + i * 4); | 
 |  | 
 | 	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 4); i++) | 
 | 		writel_relaxed(gic_data[gic_nr].saved_spi_target[i], | 
 | 			dist_base + GIC_DIST_TARGET + i * 4); | 
 |  | 
 | 	for (i = 0; i < DIV_ROUND_UP(gic_irqs, 32); i++) | 
 | 		writel_relaxed(gic_data[gic_nr].saved_spi_enable[i], | 
 | 			dist_base + GIC_DIST_ENABLE_SET + i * 4); | 
 |  | 
 | 	writel_relaxed(1, dist_base + GIC_DIST_CTRL); | 
 | } | 
 |  | 
 | static void gic_cpu_save(unsigned int gic_nr) | 
 | { | 
 | 	int i; | 
 | 	u32 *ptr; | 
 | 	void __iomem *dist_base; | 
 | 	void __iomem *cpu_base; | 
 |  | 
 | 	if (gic_nr >= MAX_GIC_NR) | 
 | 		BUG(); | 
 |  | 
 | 	dist_base = gic_data_dist_base(&gic_data[gic_nr]); | 
 | 	cpu_base = gic_data_cpu_base(&gic_data[gic_nr]); | 
 |  | 
 | 	if (!dist_base || !cpu_base) | 
 | 		return; | 
 |  | 
 | 	ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_enable); | 
 | 	for (i = 0; i < DIV_ROUND_UP(32, 32); i++) | 
 | 		ptr[i] = readl_relaxed(dist_base + GIC_DIST_ENABLE_SET + i * 4); | 
 |  | 
 | 	ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_conf); | 
 | 	for (i = 0; i < DIV_ROUND_UP(32, 16); i++) | 
 | 		ptr[i] = readl_relaxed(dist_base + GIC_DIST_CONFIG + i * 4); | 
 |  | 
 | } | 
 |  | 
 | static void gic_cpu_restore(unsigned int gic_nr) | 
 | { | 
 | 	int i; | 
 | 	u32 *ptr; | 
 | 	void __iomem *dist_base; | 
 | 	void __iomem *cpu_base; | 
 |  | 
 | 	if (gic_nr >= MAX_GIC_NR) | 
 | 		BUG(); | 
 |  | 
 | 	dist_base = gic_data_dist_base(&gic_data[gic_nr]); | 
 | 	cpu_base = gic_data_cpu_base(&gic_data[gic_nr]); | 
 |  | 
 | 	if (!dist_base || !cpu_base) | 
 | 		return; | 
 |  | 
 | 	ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_enable); | 
 | 	for (i = 0; i < DIV_ROUND_UP(32, 32); i++) | 
 | 		writel_relaxed(ptr[i], dist_base + GIC_DIST_ENABLE_SET + i * 4); | 
 |  | 
 | 	ptr = __this_cpu_ptr(gic_data[gic_nr].saved_ppi_conf); | 
 | 	for (i = 0; i < DIV_ROUND_UP(32, 16); i++) | 
 | 		writel_relaxed(ptr[i], dist_base + GIC_DIST_CONFIG + i * 4); | 
 |  | 
 | 	for (i = 0; i < DIV_ROUND_UP(32, 4); i++) | 
 | 		writel_relaxed(0xa0a0a0a0, dist_base + GIC_DIST_PRI + i * 4); | 
 |  | 
 | 	writel_relaxed(0xf0, cpu_base + GIC_CPU_PRIMASK); | 
 | 	writel_relaxed(1, cpu_base + GIC_CPU_CTRL); | 
 | } | 
 |  | 
 | static int gic_notifier(struct notifier_block *self, unsigned long cmd,	void *v) | 
 | { | 
 | 	int i; | 
 |  | 
 | 	for (i = 0; i < MAX_GIC_NR; i++) { | 
 | #ifdef CONFIG_GIC_NON_BANKED | 
 | 		/* Skip over unused GICs */ | 
 | 		if (!gic_data[i].get_base) | 
 | 			continue; | 
 | #endif | 
 | 		switch (cmd) { | 
 | 		case CPU_PM_ENTER: | 
 | 			gic_cpu_save(i); | 
 | 			break; | 
 | 		case CPU_PM_ENTER_FAILED: | 
 | 		case CPU_PM_EXIT: | 
 | 			gic_cpu_restore(i); | 
 | 			break; | 
 | 		case CPU_CLUSTER_PM_ENTER: | 
 | 			gic_dist_save(i); | 
 | 			break; | 
 | 		case CPU_CLUSTER_PM_ENTER_FAILED: | 
 | 		case CPU_CLUSTER_PM_EXIT: | 
 | 			gic_dist_restore(i); | 
 | 			break; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	return NOTIFY_OK; | 
 | } | 
 |  | 
 | static struct notifier_block gic_notifier_block = { | 
 | 	.notifier_call = gic_notifier, | 
 | }; | 
 |  | 
 | static void __init gic_pm_init(struct gic_chip_data *gic) | 
 | { | 
 | 	gic->saved_ppi_enable = __alloc_percpu(DIV_ROUND_UP(32, 32) * 4, | 
 | 		sizeof(u32)); | 
 | 	BUG_ON(!gic->saved_ppi_enable); | 
 |  | 
 | 	gic->saved_ppi_conf = __alloc_percpu(DIV_ROUND_UP(32, 16) * 4, | 
 | 		sizeof(u32)); | 
 | 	BUG_ON(!gic->saved_ppi_conf); | 
 |  | 
 | 	if (gic == &gic_data[0]) | 
 | 		cpu_pm_register_notifier(&gic_notifier_block); | 
 | } | 
 | #else | 
 | static void __init gic_pm_init(struct gic_chip_data *gic) | 
 | { | 
 | } | 
 | #endif | 
 |  | 
 | #ifdef CONFIG_SMP | 
 | void gic_raise_softirq(const struct cpumask *mask, unsigned int irq) | 
 | { | 
 | 	int cpu; | 
 | 	unsigned long flags, map = 0; | 
 |  | 
 | 	raw_spin_lock_irqsave(&irq_controller_lock, flags); | 
 |  | 
 | 	/* Convert our logical CPU mask into a physical one. */ | 
 | 	for_each_cpu(cpu, mask) | 
 | 		map |= gic_cpu_map[cpu]; | 
 |  | 
 | 	/* | 
 | 	 * Ensure that stores to Normal memory are visible to the | 
 | 	 * other CPUs before issuing the IPI. | 
 | 	 */ | 
 | 	dsb(); | 
 |  | 
 | 	/* this always happens on GIC0 */ | 
 | 	writel_relaxed(map << 16 | irq, gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT); | 
 |  | 
 | 	raw_spin_unlock_irqrestore(&irq_controller_lock, flags); | 
 | } | 
 | #endif | 
 |  | 
 | #ifdef CONFIG_BL_SWITCHER | 
 | /* | 
 |  * gic_send_sgi - send a SGI directly to given CPU interface number | 
 |  * | 
 |  * cpu_id: the ID for the destination CPU interface | 
 |  * irq: the IPI number to send a SGI for | 
 |  */ | 
 | void gic_send_sgi(unsigned int cpu_id, unsigned int irq) | 
 | { | 
 | 	BUG_ON(cpu_id >= NR_GIC_CPU_IF); | 
 | 	cpu_id = 1 << cpu_id; | 
 | 	/* this always happens on GIC0 */ | 
 | 	writel_relaxed((cpu_id << 16) | irq, gic_data_dist_base(&gic_data[0]) + GIC_DIST_SOFTINT); | 
 | } | 
 |  | 
 | /* | 
 |  * gic_get_cpu_id - get the CPU interface ID for the specified CPU | 
 |  * | 
 |  * @cpu: the logical CPU number to get the GIC ID for. | 
 |  * | 
 |  * Return the CPU interface ID for the given logical CPU number, | 
 |  * or -1 if the CPU number is too large or the interface ID is | 
 |  * unknown (more than one bit set). | 
 |  */ | 
 | int gic_get_cpu_id(unsigned int cpu) | 
 | { | 
 | 	unsigned int cpu_bit; | 
 |  | 
 | 	if (cpu >= NR_GIC_CPU_IF) | 
 | 		return -1; | 
 | 	cpu_bit = gic_cpu_map[cpu]; | 
 | 	if (cpu_bit & (cpu_bit - 1)) | 
 | 		return -1; | 
 | 	return __ffs(cpu_bit); | 
 | } | 
 |  | 
 | /* | 
 |  * gic_migrate_target - migrate IRQs to another CPU interface | 
 |  * | 
 |  * @new_cpu_id: the CPU target ID to migrate IRQs to | 
 |  * | 
 |  * Migrate all peripheral interrupts with a target matching the current CPU | 
 |  * to the interface corresponding to @new_cpu_id.  The CPU interface mapping | 
 |  * is also updated.  Targets to other CPU interfaces are unchanged. | 
 |  * This must be called with IRQs locally disabled. | 
 |  */ | 
 | void gic_migrate_target(unsigned int new_cpu_id) | 
 | { | 
 | 	unsigned int cur_cpu_id, gic_irqs, gic_nr = 0; | 
 | 	void __iomem *dist_base; | 
 | 	int i, ror_val, cpu = smp_processor_id(); | 
 | 	u32 val, cur_target_mask, active_mask; | 
 |  | 
 | 	if (gic_nr >= MAX_GIC_NR) | 
 | 		BUG(); | 
 |  | 
 | 	dist_base = gic_data_dist_base(&gic_data[gic_nr]); | 
 | 	if (!dist_base) | 
 | 		return; | 
 | 	gic_irqs = gic_data[gic_nr].gic_irqs; | 
 |  | 
 | 	cur_cpu_id = __ffs(gic_cpu_map[cpu]); | 
 | 	cur_target_mask = 0x01010101 << cur_cpu_id; | 
 | 	ror_val = (cur_cpu_id - new_cpu_id) & 31; | 
 |  | 
 | 	raw_spin_lock(&irq_controller_lock); | 
 |  | 
 | 	/* Update the target interface for this logical CPU */ | 
 | 	gic_cpu_map[cpu] = 1 << new_cpu_id; | 
 |  | 
 | 	/* | 
 | 	 * Find all the peripheral interrupts targetting the current | 
 | 	 * CPU interface and migrate them to the new CPU interface. | 
 | 	 * We skip DIST_TARGET 0 to 7 as they are read-only. | 
 | 	 */ | 
 | 	for (i = 8; i < DIV_ROUND_UP(gic_irqs, 4); i++) { | 
 | 		val = readl_relaxed(dist_base + GIC_DIST_TARGET + i * 4); | 
 | 		active_mask = val & cur_target_mask; | 
 | 		if (active_mask) { | 
 | 			val &= ~active_mask; | 
 | 			val |= ror32(active_mask, ror_val); | 
 | 			writel_relaxed(val, dist_base + GIC_DIST_TARGET + i*4); | 
 | 		} | 
 | 	} | 
 |  | 
 | 	raw_spin_unlock(&irq_controller_lock); | 
 |  | 
 | 	/* | 
 | 	 * Now let's migrate and clear any potential SGIs that might be | 
 | 	 * pending for us (cur_cpu_id).  Since GIC_DIST_SGI_PENDING_SET | 
 | 	 * is a banked register, we can only forward the SGI using | 
 | 	 * GIC_DIST_SOFTINT.  The original SGI source is lost but Linux | 
 | 	 * doesn't use that information anyway. | 
 | 	 * | 
 | 	 * For the same reason we do not adjust SGI source information | 
 | 	 * for previously sent SGIs by us to other CPUs either. | 
 | 	 */ | 
 | 	for (i = 0; i < 16; i += 4) { | 
 | 		int j; | 
 | 		val = readl_relaxed(dist_base + GIC_DIST_SGI_PENDING_SET + i); | 
 | 		if (!val) | 
 | 			continue; | 
 | 		writel_relaxed(val, dist_base + GIC_DIST_SGI_PENDING_CLEAR + i); | 
 | 		for (j = i; j < i + 4; j++) { | 
 | 			if (val & 0xff) | 
 | 				writel_relaxed((1 << (new_cpu_id + 16)) | j, | 
 | 						dist_base + GIC_DIST_SOFTINT); | 
 | 			val >>= 8; | 
 | 		} | 
 | 	} | 
 | } | 
 |  | 
 | /* | 
 |  * gic_get_sgir_physaddr - get the physical address for the SGI register | 
 |  * | 
 |  * REturn the physical address of the SGI register to be used | 
 |  * by some early assembly code when the kernel is not yet available. | 
 |  */ | 
 | static unsigned long gic_dist_physaddr; | 
 |  | 
 | unsigned long gic_get_sgir_physaddr(void) | 
 | { | 
 | 	if (!gic_dist_physaddr) | 
 | 		return 0; | 
 | 	return gic_dist_physaddr + GIC_DIST_SOFTINT; | 
 | } | 
 |  | 
 | void __init gic_init_physaddr(struct device_node *node) | 
 | { | 
 | 	struct resource res; | 
 | 	if (of_address_to_resource(node, 0, &res) == 0) { | 
 | 		gic_dist_physaddr = res.start; | 
 | 		pr_info("GIC physical location is %#lx\n", gic_dist_physaddr); | 
 | 	} | 
 | } | 
 |  | 
 | #else | 
 | #define gic_init_physaddr(node)  do { } while (0) | 
 | #endif | 
 |  | 
 | static int gic_irq_domain_map(struct irq_domain *d, unsigned int irq, | 
 | 				irq_hw_number_t hw) | 
 | { | 
 | 	if (hw < 32) { | 
 | 		irq_set_percpu_devid(irq); | 
 | 		irq_set_chip_and_handler(irq, &gic_chip, | 
 | 					 handle_percpu_devid_irq); | 
 | 		set_irq_flags(irq, IRQF_VALID | IRQF_NOAUTOEN); | 
 | 	} else { | 
 | 		irq_set_chip_and_handler(irq, &gic_chip, | 
 | 					 handle_fasteoi_irq); | 
 | 		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE); | 
 | 	} | 
 | 	irq_set_chip_data(irq, d->host_data); | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int gic_irq_domain_xlate(struct irq_domain *d, | 
 | 				struct device_node *controller, | 
 | 				const u32 *intspec, unsigned int intsize, | 
 | 				unsigned long *out_hwirq, unsigned int *out_type) | 
 | { | 
 | 	if (d->of_node != controller) | 
 | 		return -EINVAL; | 
 | 	if (intsize < 3) | 
 | 		return -EINVAL; | 
 |  | 
 | 	/* Get the interrupt number and add 16 to skip over SGIs */ | 
 | 	*out_hwirq = intspec[1] + 16; | 
 |  | 
 | 	/* For SPIs, we need to add 16 more to get the GIC irq ID number */ | 
 | 	if (!intspec[0]) | 
 | 		*out_hwirq += 16; | 
 |  | 
 | 	*out_type = intspec[2] & IRQ_TYPE_SENSE_MASK; | 
 | 	return 0; | 
 | } | 
 |  | 
 | #ifdef CONFIG_SMP | 
 | static int gic_secondary_init(struct notifier_block *nfb, unsigned long action, | 
 | 			      void *hcpu) | 
 | { | 
 | 	if (action == CPU_STARTING || action == CPU_STARTING_FROZEN) | 
 | 		gic_cpu_init(&gic_data[0]); | 
 | 	return NOTIFY_OK; | 
 | } | 
 |  | 
 | /* | 
 |  * Notifier for enabling the GIC CPU interface. Set an arbitrarily high | 
 |  * priority because the GIC needs to be up before the ARM generic timers. | 
 |  */ | 
 | static struct notifier_block gic_cpu_notifier = { | 
 | 	.notifier_call = gic_secondary_init, | 
 | 	.priority = 100, | 
 | }; | 
 | #endif | 
 |  | 
 | const struct irq_domain_ops gic_irq_domain_ops = { | 
 | 	.map = gic_irq_domain_map, | 
 | 	.xlate = gic_irq_domain_xlate, | 
 | }; | 
 |  | 
 | void __init gic_init_bases(unsigned int gic_nr, int irq_start, | 
 | 			   void __iomem *dist_base, void __iomem *cpu_base, | 
 | 			   u32 percpu_offset, struct device_node *node) | 
 | { | 
 | 	irq_hw_number_t hwirq_base; | 
 | 	struct gic_chip_data *gic; | 
 | 	int gic_irqs, irq_base, i, index; | 
 |     int nr_routable_irqs; | 
 |  | 
 | 	BUG_ON(gic_nr >= MAX_GIC_NR); | 
 |  | 
 | 	gic = &gic_data[gic_nr]; | 
 | #ifdef CONFIG_GIC_NON_BANKED | 
 | 	if (percpu_offset) { /* Frankein-GIC without banked registers... */ | 
 | 		unsigned int cpu; | 
 |  | 
 | 		gic->dist_base.percpu_base = alloc_percpu(void __iomem *); | 
 | 		gic->cpu_base.percpu_base = alloc_percpu(void __iomem *); | 
 | 		if (WARN_ON(!gic->dist_base.percpu_base || | 
 | 			    !gic->cpu_base.percpu_base)) { | 
 | 			free_percpu(gic->dist_base.percpu_base); | 
 | 			free_percpu(gic->cpu_base.percpu_base); | 
 | 			return; | 
 | 		} | 
 |  | 
 | 		for_each_possible_cpu(cpu) { | 
 | 			unsigned long offset = percpu_offset * cpu_logical_map(cpu); | 
 | 			*per_cpu_ptr(gic->dist_base.percpu_base, cpu) = dist_base + offset; | 
 | 			*per_cpu_ptr(gic->cpu_base.percpu_base, cpu) = cpu_base + offset; | 
 | 		} | 
 |  | 
 | 		gic_set_base_accessor(gic, gic_get_percpu_base); | 
 | 	} else | 
 | #endif | 
 | 	{			/* Normal, sane GIC... */ | 
 | 	WARN(percpu_offset, | 
 | 	     "GIC_NON_BANKED not enabled, ignoring %08x offset!", | 
 | 	     percpu_offset); | 
 | 	gic->dist_base.common_base = dist_base; | 
 | 	gic->cpu_base.common_base = cpu_base; | 
 | 		gic_set_base_accessor(gic, gic_get_common_base); | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * Initialize the CPU interface map to all CPUs. | 
 | 	 * It will be refined as each CPU probes its ID. | 
 | 	 */ | 
 | 	for (i = 0; i < NR_GIC_CPU_IF; i++) | 
 | 		gic_cpu_map[i] = 0xff; | 
 |  | 
 | 	/* | 
 | 	 * For primary GICs, skip over SGIs. | 
 | 	 * For secondary GICs, skip over PPIs, too. | 
 | 	 */ | 
 | 	if (gic_nr == 0 && (irq_start & 31) > 0) { | 
 | 		hwirq_base = 16; | 
 | 		if (irq_start != -1) | 
 | 			irq_start = (irq_start & ~31) + 16; | 
 | 	} else { | 
 | 		hwirq_base = 32; | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * Find out how many interrupts are supported. | 
 | 	 * The GIC only supports up to 1020 interrupt sources. | 
 | 	 */ | 
 | 	/*gic_irqs = readl_relaxed(gic_data_dist_base(gic) + GIC_DIST_CTR) & 0x1f; | 
 | 	gic_irqs = (gic_irqs + 1) * 32; | 
 | 	if (gic_irqs > 1020) | 
 | 		gic_irqs = 1020; | 
 | 	gic->gic_irqs = gic_irqs;*/ | 
 | 	 | 
 | 	/* | 
 | 	 * irq numbers in linux must not be less than numbers of irq supported by all interrupt controllers | 
 | 	 * in zx297510 there is only 110 irqs, but gic supports 256 irqs.so wo set gic_irqs 110,ignore bit[4:0] | 
 | 	 * in GIC_DIST_CTR register. | 
 | 	 */ | 
 | 	gic_irqs=NR_IRQS; | 
 |     gic->gic_irqs = gic_irqs; | 
 |  | 
 | 	gic_irqs -= hwirq_base; /* calculate # of irqs to allocate */ | 
 |  | 
 |     if (of_property_read_u32(node, "arm,routable-irqs", | 
 |                              &nr_routable_irqs)) | 
 |     { | 
 |         irq_base = irq_alloc_descs(irq_start, 16, gic_irqs, | 
 |                                    numa_node_id()); | 
 |         if (IS_ERR_VALUE(irq_base)) | 
 |         { | 
 |             WARN(1, "Cannot allocate irq_descs @ IRQ%d, assuming pre-allocated\n", | 
 |                  irq_start); | 
 |             irq_base = irq_start; | 
 |         } | 
 |  | 
 |         gic->domain = irq_domain_add_legacy(node, gic_irqs, irq_base, | 
 |                                             hwirq_base, &gic_irq_domain_ops, gic); | 
 |     } | 
 |     else | 
 |     { | 
 |         gic->domain = irq_domain_add_linear(node, nr_routable_irqs, | 
 |                                             &gic_irq_domain_ops, | 
 |                                             gic); | 
 |     } | 
 |  | 
 |     if (WARN_ON(!gic->domain)) | 
 |     { | 
 |         return; | 
 |     } | 
 |  | 
 |     if (gic_nr == 0) | 
 |     { | 
 | #ifdef CONFIG_SMP | 
 |         set_smp_cross_call(gic_raise_softirq); | 
 |         register_cpu_notifier(&gic_cpu_notifier); | 
 | #endif | 
 |         set_handle_irq(gic_handle_irq); | 
 |     } | 
 |  | 
 |     gic_chip.flags |= gic_arch_extn.flags; | 
 |     gic_dist_init(gic); | 
 |     gic_cpu_init(gic); | 
 |     gic_pm_init(gic); | 
 | 	for(index = 0; index < ARRAYSIZE(wakeup_int_cfg); index++) | 
 | 	{ | 
 | 		wakeup_int[wakeup_int_cfg[index] - GIC_SPI_START] = 1; | 
 | 	} | 
 | } | 
 |  | 
 | unsigned int gic_get_irq_nr(irq_hw_number_t hwirq) | 
 | { | 
 | 	return irq_find_mapping(gic_data[0].domain, hwirq);    //get linux irq number | 
 | } | 
 |  | 
 |  | 
 | #ifdef CONFIG_OF | 
 | static int gic_cnt __initdata; | 
 |  | 
 | int __init gic_of_init(struct device_node *node, struct device_node *parent) | 
 | { | 
 | 	void __iomem *cpu_base; | 
 | 	void __iomem *dist_base; | 
 | 	u32 percpu_offset; | 
 | 	int irq; | 
 |  | 
 | 	if (WARN_ON(!node)) | 
 | 		return -ENODEV; | 
 |  | 
 | 	dist_base = of_iomap(node, 0); | 
 | 	WARN(!dist_base, "unable to map gic dist registers\n"); | 
 |  | 
 | 	cpu_base = of_iomap(node, 1); | 
 | 	WARN(!cpu_base, "unable to map gic cpu registers\n"); | 
 |  | 
 | 	if (of_property_read_u32(node, "cpu-offset", &percpu_offset)) | 
 | 		percpu_offset = 0; | 
 |  | 
 | 	gic_init_bases(gic_cnt, -1, dist_base, cpu_base, percpu_offset, node); | 
 | 	if (!gic_cnt) | 
 | 		gic_init_physaddr(node); | 
 |  | 
 | 	if (parent) { | 
 | 		irq = irq_of_parse_and_map(node, 0); | 
 | 		gic_cascade_irq(gic_cnt, irq); | 
 | 	} | 
 | 	gic_cnt++; | 
 | 	return 0; | 
 | } | 
 | IRQCHIP_DECLARE(cortex_a15_gic, "arm,cortex-a15-gic", gic_of_init); | 
 | IRQCHIP_DECLARE(cortex_a9_gic, "arm,cortex-a9-gic", gic_of_init); | 
 | IRQCHIP_DECLARE(msm_8660_qgic, "qcom,msm-8660-qgic", gic_of_init); | 
 | IRQCHIP_DECLARE(msm_qgic2, "qcom,msm-qgic2", gic_of_init); | 
 |  | 
 | #endif |