[T106][ZXW-22]7520V3SCV2.01.01.02P42U09_VEC_V0.8_AP_VEC origin source commit
Change-Id: Ic6e05d89ecd62fc34f82b23dcf306c93764aec4b
diff --git a/ap/app/Script/wifi/realtek/ath/wscd.conf b/ap/app/Script/wifi/realtek/ath/wscd.conf
new file mode 100644
index 0000000..4402f39
--- /dev/null
+++ b/ap/app/Script/wifi/realtek/ath/wscd.conf
@@ -0,0 +1,75 @@
+#detail please reference config_file_README.txt
+wlan_fifo0 ="/etc_rw/wifi/realtek/wscd-wlan0.fifo"
+wlan_fifo1 ="/etc_rw/wifi/realtek/wscd-wlan1.fifo"
+
+SSID_prefix = "Reaktek_AP_"
+
+use_ie = 1
+
+# AUTH_OPEN=1, AUTH_WPAPSK=2, AUTH_SHARED=4, AUTH_WPA=8, AUTH_WPA2=0x10, AUTH_WPA2PSK=0x20
+auth_type_flags = 39
+
+# ENCRYPT_NONE=1, ENCRYPT_WEP=2, ENCRYPT_TKIP=4, ENCRYPT_AES=8
+encrypt_type_flags = 15
+
+uuid = 63041253101920061228aabbccddeeff
+device_name = "RTK_AP"
+manufacturer = "Realtek"
+manufacturerURL = "http://www.realtek.com/"
+modelURL = "http://www.realtek.com/"
+model_name = "RTL8xxx"
+model_num = "EV-2010-09-20"
+serial_num = "123456789012347"
+modelDescription = "WLAN Access Point"
+device_attrib_id = 1
+device_oui = 0050f204
+device_category_id = 6
+device_sub_category_id = 1
+
+# PASS_ID_DEFAULT=0, PASS_ID_USER=1, PASS_ID_MACHINE=2, PASS_ID_REKEY=3,
+# PASS_ID_PB=4, PASS_ID_REG=5, PASS_ID_RESERVED=6
+device_password_id = 0
+
+tx_timeout = 5
+resent_limit = 2
+reg_timeout = 120
+block_timeout = 60
+
+WPS_START_LED_GPIO_number = 2
+WPS_END_LED_unconfig_GPIO_number = 0
+WPS_END_LED_config_GPIO_number = 0
+WPS_PBC_overlapping_GPIO_number = 1
+PBC_overlapping_LED_time_out = 30
+
+
+No_ifname_for_flash_set = 0
+
+#disable_disconnect = 1
+#disable_auto_gen_ssid = 1
+#manual_key_type = 2
+#manual_key = 1234567890
+#random_key_len = 64
+#PSK_LEN = 64
+
+disable_hidden_ap = 1
+
+#SSID_prefix = "RTKAP_"
+
+button_hold_time = 1
+
+# for WPS2;if wps1.0 don't define
+# 0x2008|0x480|0x680(CONFIG_METHOD_VIRTUAL_PIN | CONFIG_METHOD_PHYSICAL_PBC | CONFIG_METHOD_VIRTUAL_PBC )
+
+config_method = 9864
+#if AP mode config by EAP-base ER or auto-generate
+#but want not apply to both band then preset the paramater to 1
+#ProfileDontBothApply = 1
+
+# value=2:deny whatever config or unconfig state.
+# value=1:deny under configured state, allow when unconfig state.
+#disable_configured_by_exReg = 1
+
+#when PIN failed number >= MaxPinFailThresHold AP will indefinitely auto-lock-down
+#until user intervenes to unlock ; vaild value 1~10
+#MaxPinFailThresHold = 10
+