| #detail please reference config_file_README.txt | |
| wlan_fifo0 ="/etc_rw/wifi/realtek/wscd-wlan0.fifo" | |
| wlan_fifo1 ="/etc_rw/wifi/realtek/wscd-wlan1.fifo" | |
| SSID_prefix = "Reaktek_AP_" | |
| use_ie = 1 | |
| # AUTH_OPEN=1, AUTH_WPAPSK=2, AUTH_SHARED=4, AUTH_WPA=8, AUTH_WPA2=0x10, AUTH_WPA2PSK=0x20 | |
| auth_type_flags = 39 | |
| # ENCRYPT_NONE=1, ENCRYPT_WEP=2, ENCRYPT_TKIP=4, ENCRYPT_AES=8 | |
| encrypt_type_flags = 15 | |
| uuid = 63041253101920061228aabbccddeeff | |
| device_name = "RTK_AP" | |
| manufacturer = "Realtek" | |
| manufacturerURL = "http://www.realtek.com/" | |
| modelURL = "http://www.realtek.com/" | |
| model_name = "RTL8xxx" | |
| model_num = "EV-2010-09-20" | |
| serial_num = "123456789012347" | |
| modelDescription = "WLAN Access Point" | |
| device_attrib_id = 1 | |
| device_oui = 0050f204 | |
| device_category_id = 6 | |
| device_sub_category_id = 1 | |
| # PASS_ID_DEFAULT=0, PASS_ID_USER=1, PASS_ID_MACHINE=2, PASS_ID_REKEY=3, | |
| # PASS_ID_PB=4, PASS_ID_REG=5, PASS_ID_RESERVED=6 | |
| device_password_id = 0 | |
| tx_timeout = 5 | |
| resent_limit = 2 | |
| reg_timeout = 120 | |
| block_timeout = 60 | |
| WPS_START_LED_GPIO_number = 2 | |
| WPS_END_LED_unconfig_GPIO_number = 0 | |
| WPS_END_LED_config_GPIO_number = 0 | |
| WPS_PBC_overlapping_GPIO_number = 1 | |
| PBC_overlapping_LED_time_out = 30 | |
| No_ifname_for_flash_set = 0 | |
| #disable_disconnect = 1 | |
| #disable_auto_gen_ssid = 1 | |
| #manual_key_type = 2 | |
| #manual_key = 1234567890 | |
| #random_key_len = 64 | |
| #PSK_LEN = 64 | |
| disable_hidden_ap = 1 | |
| #SSID_prefix = "RTKAP_" | |
| button_hold_time = 1 | |
| # for WPS2;if wps1.0 don't define | |
| # 0x2008|0x480|0x680(CONFIG_METHOD_VIRTUAL_PIN | CONFIG_METHOD_PHYSICAL_PBC | CONFIG_METHOD_VIRTUAL_PBC ) | |
| config_method = 9864 | |
| #if AP mode config by EAP-base ER or auto-generate | |
| #but want not apply to both band then preset the paramater to 1 | |
| #ProfileDontBothApply = 1 | |
| # value=2:deny whatever config or unconfig state. | |
| # value=1:deny under configured state, allow when unconfig state. | |
| #disable_configured_by_exReg = 1 | |
| #when PIN failed number >= MaxPinFailThresHold AP will indefinitely auto-lock-down | |
| #until user intervenes to unlock ; vaild value 1~10 | |
| #MaxPinFailThresHold = 10 | |