| // SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
| |
| #include "ar9331.dtsi" |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| model = "8devices Carambola2"; |
| compatible = "8dev,carambola2", "qca,ar9331"; |
| |
| aliases { |
| label-mac-device = &wmac; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| wlan { |
| label = "green:wlan"; |
| gpios = <&gpio 0 GPIO_ACTIVE_LOW>; |
| linux,default-trigger = "phy0tpt"; |
| }; |
| |
| eth0 { |
| label = "orange:eth0"; |
| gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| eth1 { |
| label = "orange:eth1"; |
| gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| keys { |
| compatible = "gpio-keys"; |
| |
| wps { |
| label = "wps"; |
| linux,code = <KEY_WPS_BUTTON>; |
| gpios = <&gpio 11 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| }; |
| |
| &ref { |
| clock-frequency = <40000000>; |
| }; |
| |
| &usb { |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
| |
| &usb_phy { |
| status = "okay"; |
| }; |
| |
| &spi { |
| status = "okay"; |
| |
| flash@0 { |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <50000000>; |
| reg = <0>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| uboot: partition@0 { |
| label = "u-boot"; |
| reg = <0x000000 0x040000>; |
| read-only; |
| }; |
| |
| partition@40000 { |
| label = "u-boot-env"; |
| reg = <0x040000 0x010000>; |
| read-only; |
| }; |
| |
| partition@50000 { |
| compatible = "denx,uimage"; |
| label = "firmware"; |
| reg = <0x50000 0xfa0000>; |
| }; |
| |
| art: partition@ff0000 { |
| label = "art"; |
| reg = <0xff0000 0x010000>; |
| read-only; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdio0 { |
| status = "okay"; |
| }; |
| |
| ð0 { |
| status = "okay"; |
| mtd-mac-address = <&art 0x0>; |
| |
| gmac-config { |
| device = <&gmac>; |
| |
| switch-phy-addr-swap = <1>; |
| switch-phy-swap = <1>; |
| }; |
| }; |
| |
| ð1 { |
| status = "okay"; |
| mtd-mac-address = <&art 0x6>; |
| }; |
| |
| &wmac { |
| status = "okay"; |
| mtd-cal-data = <&art 0x1000>; |
| }; |