ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/linux/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/marvell/linux/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
new file mode 100644
index 0000000..085fbd6
--- /dev/null
+++ b/marvell/linux/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
@@ -0,0 +1,222 @@
+Qualcomm QMP PHY controller
+===========================
+
+QMP phy controller supports physical layer functionality for a number of
+controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
+
+Required properties:
+ - compatible: compatible list, contains:
+ "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074
+ "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
+ "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996,
+ "qcom,msm8998-qmp-usb3-phy" for USB3 QMP V3 phy on msm8998,
+ "qcom,msm8998-qmp-ufs-phy" for UFS QMP phy on msm8998,
+ "qcom,msm8998-qmp-pcie-phy" for PCIe QMP phy on msm8998,
+ "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845,
+ "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845,
+ "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845.
+
+- reg:
+ - index 0: address and length of register set for PHY's common
+ serdes block.
+ - index 1: address and length of the DP_COM control block (for
+ "qcom,sdm845-qmp-usb3-phy" only).
+
+- reg-names:
+ - For "qcom,sdm845-qmp-usb3-phy":
+ - Should be: "reg-base", "dp_com"
+ - For all others:
+ - The reg-names property shouldn't be defined.
+
+ - #address-cells: must be 1
+ - #size-cells: must be 1
+ - ranges: must be present
+
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: "cfg_ahb" for phy config clock,
+ "aux" for phy aux clock,
+ "ref" for 19.2 MHz ref clk,
+ "com_aux" for phy common block aux clock,
+ "ref_aux" for phy reference aux clock,
+
+ For "qcom,ipq8074-qmp-pcie-phy": no clocks are listed.
+ For "qcom,msm8996-qmp-pcie-phy" must contain:
+ "aux", "cfg_ahb", "ref".
+ For "qcom,msm8996-qmp-usb3-phy" must contain:
+ "aux", "cfg_ahb", "ref".
+ For "qcom,msm8998-qmp-usb3-phy" must contain:
+ "aux", "cfg_ahb", "ref".
+ For "qcom,msm8998-qmp-ufs-phy" must contain:
+ "ref", "ref_aux".
+ For "qcom,msm8998-qmp-pcie-phy" must contain:
+ "aux", "cfg_ahb", "ref".
+ For "qcom,sdm845-qmp-usb3-phy" must contain:
+ "aux", "cfg_ahb", "ref", "com_aux".
+ For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
+ "aux", "cfg_ahb", "ref", "com_aux".
+ For "qcom,sdm845-qmp-ufs-phy" must contain:
+ "ref", "ref_aux".
+
+ - resets: a list of phandles and reset controller specifier pairs,
+ one for each entry in reset-names.
+ - reset-names: "phy" for reset of phy block,
+ "common" for phy common block reset,
+ "cfg" for phy's ahb cfg block reset,
+ "ufsphy" for the PHY reset in the UFS controller.
+
+ For "qcom,ipq8074-qmp-pcie-phy" must contain:
+ "phy", "common".
+ For "qcom,msm8996-qmp-pcie-phy" must contain:
+ "phy", "common", "cfg".
+ For "qcom,msm8996-qmp-usb3-phy" must contain
+ "phy", "common".
+ For "qcom,msm8998-qmp-usb3-phy" must contain
+ "phy", "common".
+ For "qcom,msm8998-qmp-ufs-phy": must contain:
+ "ufsphy".
+ For "qcom,msm8998-qmp-pcie-phy" must contain:
+ "phy", "common".
+ For "qcom,sdm845-qmp-usb3-phy" must contain:
+ "phy", "common".
+ For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
+ "phy", "common".
+ For "qcom,sdm845-qmp-ufs-phy": must contain:
+ "ufsphy".
+
+ - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
+ - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
+
+Optional properties:
+ - vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
+ pll block.
+
+Required nodes:
+ - Each device node of QMP phy is required to have as many child nodes as
+ the number of lanes the PHY has.
+
+Required properties for child nodes of PCIe PHYs (one child per lane):
+ - reg: list of offset and length pairs of register sets for PHY blocks -
+ tx, rx, pcs, and pcs_misc (optional).
+ - #phy-cells: must be 0
+
+Required properties for a single "lanes" child node of non-PCIe PHYs:
+ - reg: list of offset and length pairs of register sets for PHY blocks
+ For 1-lane devices:
+ tx, rx, pcs, and (optionally) pcs_misc
+ For 2-lane devices:
+ tx0, rx0, pcs, tx1, rx1, and (optionally) pcs_misc
+ - #phy-cells: must be 0
+
+Required properties for child node of PCIe and USB3 qmp phys:
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: Must contain following:
+ "pipe<lane-number>" for pipe clock specific to each lane.
+ - clock-output-names: Name of the PHY clock that will be the parent for
+ the above pipe clock.
+ For "qcom,ipq8074-qmp-pcie-phy":
+ - "pcie20_phy0_pipe_clk" Pipe Clock parent
+ (or)
+ "pcie20_phy1_pipe_clk"
+ - #clock-cells: must be 0
+ - Phy pll outputs pipe clocks for pipe based PHYs. These clocks are then
+ gate-controlled by the gcc.
+
+Required properties for child node of PHYs with lane reset, AKA:
+ "qcom,msm8996-qmp-pcie-phy"
+ - resets: a list of phandles and reset controller specifier pairs,
+ one for each entry in reset-names.
+ - reset-names: Must contain following:
+ "lane<lane-number>" for reset specific to each lane.
+
+Example:
+ phy@34000 {
+ compatible = "qcom,msm8996-qmp-pcie-phy";
+ reg = <0x34000 0x488>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_CLKREF_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
+
+ resets = <&gcc GCC_PCIE_PHY_BCR>,
+ <&gcc GCC_PCIE_PHY_COM_BCR>,
+ <&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
+ reset-names = "phy", "common", "cfg";
+
+ pciephy_0: lane@35000 {
+ reg = <0x35000 0x130>,
+ <0x35200 0x200>,
+ <0x35400 0x1dc>;
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "pcie_0_pipe_clk_src";
+ resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+ reset-names = "lane0";
+ };
+
+ pciephy_1: lane@36000 {
+ ...
+ ...
+ };
+
+ phy@88eb000 {
+ compatible = "qcom,sdm845-qmp-usb3-uni-phy";
+ reg = <0x88eb000 0x18c>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_SEC_CLKREF_CLK>,
+ <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+ resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
+ <&gcc GCC_USB3_PHY_SEC_BCR>;
+ reset-names = "phy", "common";
+
+ lane@88eb200 {
+ reg = <0x88eb200 0x128>,
+ <0x88eb400 0x1fc>,
+ <0x88eb800 0x218>,
+ <0x88eb600 0x70>;
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_uni_phy_pipe_clk_src";
+ };
+ };
+
+ phy@1d87000 {
+ compatible = "qcom,sdm845-qmp-ufs-phy";
+ reg = <0x1d87000 0x18c>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clock-names = "ref",
+ "ref_aux";
+ clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
+ <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
+
+ lanes@1d87400 {
+ reg = <0x1d87400 0x108>,
+ <0x1d87600 0x1e0>,
+ <0x1d87c00 0x1dc>,
+ <0x1d87800 0x108>,
+ <0x1d87a00 0x1e0>;
+ #phy-cells = <0>;
+ };
+ };