ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/linux/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/marvell/linux/arch/arm/boot/dts/at91-sama5d2_xplained.dts
new file mode 100644
index 0000000..808e399
--- /dev/null
+++ b/marvell/linux/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -0,0 +1,641 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d2_xplained.dts - Device Tree file for SAMA5D2 Xplained board
+ *
+ * Copyright (C) 2015 Atmel,
+ * 2015 Nicolas Ferre <nicolas.ferre@atmel.com>
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/active-semi,8945a-regulator.h>
+
+/ {
+ model = "Atmel SAMA5D2 Xplained";
+ compatible = "atmel,sama5d2-xplained", "atmel,sama5d2", "atmel,sama5";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ usb0: gadget@300000 {
+ atmel,vbus-gpio = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+
+ usb1: ohci@400000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0 /* &pioA PIN_PB9 GPIO_ACTIVE_HIGH */
+ &pioA PIN_PB10 GPIO_ACTIVE_HIGH
+ 0
+ >;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_default>;
+ status = "okay";
+ };
+
+ usb2: ehci@500000 {
+ status = "okay";
+ };
+
+ sdmmc0: sdio-host@a0000000 {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ non-removable;
+ mmc-ddr-1_8v;
+ status = "okay";
+ };
+
+ sdmmc1: sdio-host@b0000000 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc1_default>;
+ status = "okay"; /* conflict with qspi0 */
+ vqmmc-supply = <&vdd_3v3_reg>;
+ vmmc-supply = <&vdd_3v3_reg>;
+ };
+
+ apb {
+ spi0: spi@f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0_default>;
+ status = "okay";
+
+ m25p80@0 {
+ compatible = "atmel,at25df321a";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
+ };
+
+ macb0: ethernet@f8008000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+ phy-mode = "rmii";
+ status = "okay";
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioA>;
+ interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+
+ tcb0: timer@f800c000 {
+ timer0: timer@0 {
+ compatible = "atmel,tcb-timer";
+ reg = <0>;
+ };
+
+ timer1: timer@1 {
+ compatible = "atmel,tcb-timer";
+ reg = <1>;
+ };
+ };
+
+ pdmic@f8018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pdmic_default>;
+ atmel,model = "PDMIC @ sama5d2_xplained";
+ atmel,mic-min-freq = <1000000>;
+ atmel,mic-max-freq = <3246000>;
+ atmel,mic-offset = <0x0>;
+ status = "okay";
+ };
+
+ uart1: serial@f8020000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+ };
+
+ i2c0: i2c@f8028000 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ i2c-sda-hold-time-ns = <350>;
+ status = "okay";
+
+ pmic@5b {
+ compatible = "active-semi,act8945a";
+ reg = <0x5b>;
+ active-semi,vsel-high;
+ status = "okay";
+
+ regulators {
+ vdd_1v35_reg: REG_DCDC1 {
+ regulator-name = "VDD_1V35";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+ <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+ regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-min-microvolt=<1400000>;
+ regulator-suspend-max-microvolt=<1400000>;
+ regulator-changeable-in-suspend;
+ regulator-mode=<ACT8945A_REGULATOR_MODE_LOWPOWER>;
+ };
+ };
+
+ vdd_1v2_reg: REG_DCDC2 {
+ regulator-name = "VDD_1V2";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+ <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+ regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_3v3_reg: REG_DCDC3 {
+ regulator-name = "VDD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+ <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+ regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_fuse_reg: REG_LDO1 {
+ regulator-name = "VDD_FUSE";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>,
+ <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+ regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_3v3_lp_reg: REG_LDO2 {
+ regulator-name = "VDD_3V3_LP";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>,
+ <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+ regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_led_reg: REG_LDO3 {
+ regulator-name = "VDD_LED";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>,
+ <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+ regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_sdhc_1v8_reg: REG_LDO4 {
+ regulator-name = "VDD_SDHC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>,
+ <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+ regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+
+ charger {
+ compatible = "active-semi,act8945a-charger";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>;
+ interrupt-parent = <&pioA>;
+ interrupts = <PIN_PB13 IRQ_TYPE_EDGE_RISING>;
+
+ active-semi,chglev-gpios = <&pioA PIN_PA12 GPIO_ACTIVE_HIGH>;
+ active-semi,lbo-gpios = <&pioA PIN_PC8 GPIO_ACTIVE_LOW>;
+ active-semi,input-voltage-threshold-microvolt = <6600>;
+ active-semi,precondition-timeout = <40>;
+ active-semi,total-timeout = <3>;
+ status = "okay";
+ };
+ };
+ };
+
+ pwm0: pwm@f802c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_pwm2_default>;
+ status = "disabled"; /* conflict with leds */
+ };
+
+ flx0: flexcom@f8034000 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+ status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
+
+ uart5: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
+ clock-names = "usart";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx0_default>;
+ atmel,fifo-size = <32>;
+ status = "okay";
+ };
+ };
+
+ shdwc@f8048010 {
+ atmel,shdwc-debouncer = <976>;
+ atmel,wakeup-rtc-timer;
+
+ input@0 {
+ reg = <0>;
+ atmel,wakeup-type = "low";
+ };
+ };
+
+ watchdog@f8048040 {
+ status = "okay";
+ };
+
+ i2s0: i2s@f8050000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2s0_default>;
+ status = "disabled"; /* conflict with can0 */
+ };
+
+ can0: can@f8054000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can0_default>;
+ status = "okay";
+ };
+
+ uart3: serial@fc008000 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3_default>;
+ status = "okay";
+ };
+
+ flx4: flexcom@fc018000 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "okay";
+
+ i2c2: i2c@600 {
+ compatible = "atmel,sama5d2-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <0>, <0>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx4_default>;
+ atmel,fifo-size = <16>;
+ status = "okay";
+ };
+ };
+
+ i2c1: i2c@fc028000 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ status = "okay";
+
+ at24@54 {
+ compatible = "atmel,24c02";
+ reg = <0x54>;
+ pagesize = <16>;
+ };
+ };
+
+ adc: adc@fc030000 {
+ vddana-supply = <&vdd_3v3_lp_reg>;
+ vref-supply = <&vdd_3v3_lp_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
+ status = "okay";
+ };
+
+ pinctrl@fc038000 {
+ /*
+ * There is no real pinmux for ADC, if the pin
+ * is not requested by another peripheral then
+ * the muxing is done when channel is enabled.
+ * Requesting pins for ADC is GPIO is
+ * encouraged to prevent conflicts and to
+ * disable bias in order to be in the same
+ * state when the pin is not muxed to the adc.
+ */
+ pinctrl_adc_default: adc_default {
+ pinmux = <PIN_PD23__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_can0_default: can0_default {
+ pinmux = <PIN_PC10__CANTX0>,
+ <PIN_PC11__CANRX0>;
+ bias-disable;
+ };
+
+ pinctrl_can1_default: can1_default {
+ pinmux = <PIN_PC26__CANTX1>,
+ <PIN_PC27__CANRX1>;
+ bias-disable;
+ };
+
+ /*
+ * The ADTRG pin can work on any edge type.
+ * In here it's being pulled up, so need to
+ * connect it to ground to get an edge e.g.
+ * Trigger can be configured on falling, rise
+ * or any edge, and the pull-up can be changed
+ * to pull-down or left floating according to
+ * needs.
+ */
+ pinctrl_adtrg_default: adtrg_default {
+ pinmux = <PIN_PD31__ADTRG>;
+ bias-pull-up;
+ };
+
+ pinctrl_charger_chglev: charger_chglev {
+ pinmux = <PIN_PA12__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_charger_irq: charger_irq {
+ pinmux = <PIN_PB13__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_charger_lbo: charger_lbo {
+ pinmux = <PIN_PC8__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_classd_default: classd_default {
+ pinmux = <PIN_PB1__CLASSD_R0>,
+ <PIN_PB2__CLASSD_R1>,
+ <PIN_PB3__CLASSD_R2>,
+ <PIN_PB4__CLASSD_R3>;
+ bias-pull-up;
+ };
+
+ pinctrl_flx0_default: flx0_default {
+ pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+ <PIN_PB29__FLEXCOM0_IO1>;
+ bias-disable;
+ };
+
+ pinctrl_flx4_default: flx4_default {
+ pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+ <PIN_PD13__FLEXCOM4_IO1>;
+ bias-disable;
+ };
+
+ pinctrl_i2c0_default: i2c0_default {
+ pinmux = <PIN_PD21__TWD0>,
+ <PIN_PD22__TWCK0>;
+ bias-disable;
+ };
+
+ pinctrl_i2c1_default: i2c1_default {
+ pinmux = <PIN_PD4__TWD1>,
+ <PIN_PD5__TWCK1>;
+ bias-disable;
+ };
+
+ pinctrl_i2s0_default: i2s0_default {
+ pinmux = <PIN_PC1__I2SC0_CK>,
+ <PIN_PC2__I2SC0_MCK>,
+ <PIN_PC3__I2SC0_WS>,
+ <PIN_PC4__I2SC0_DI0>,
+ <PIN_PC5__I2SC0_DO0>;
+ bias-disable;
+ };
+
+ pinctrl_i2s1_default: i2s1_default {
+ pinmux = <PIN_PA15__I2SC1_CK>,
+ <PIN_PA14__I2SC1_MCK>,
+ <PIN_PA16__I2SC1_WS>,
+ <PIN_PA17__I2SC1_DI0>,
+ <PIN_PA18__I2SC1_DO0>;
+ bias-disable;
+ };
+
+ pinctrl_key_gpio_default: key_gpio_default {
+ pinmux = <PIN_PB9__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_led_gpio_default: led_gpio_default {
+ pinmux = <PIN_PB0__GPIO>,
+ <PIN_PB5__GPIO>,
+ <PIN_PB6__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_macb0_default: macb0_default {
+ pinmux = <PIN_PB14__GTXCK>,
+ <PIN_PB15__GTXEN>,
+ <PIN_PB16__GRXDV>,
+ <PIN_PB17__GRXER>,
+ <PIN_PB18__GRX0>,
+ <PIN_PB19__GRX1>,
+ <PIN_PB20__GTX0>,
+ <PIN_PB21__GTX1>,
+ <PIN_PB22__GMDC>,
+ <PIN_PB23__GMDIO>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ pinmux = <PIN_PC9__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_pdmic_default: pdmic_default {
+ pinmux = <PIN_PB26__PDMIC_DAT>,
+ <PIN_PB27__PDMIC_CLK>;
+ bias-disable;
+ };
+
+ pinctrl_sdmmc0_default: sdmmc0_default {
+ cmd_data {
+ pinmux = <PIN_PA1__SDMMC0_CMD>,
+ <PIN_PA2__SDMMC0_DAT0>,
+ <PIN_PA3__SDMMC0_DAT1>,
+ <PIN_PA4__SDMMC0_DAT2>,
+ <PIN_PA5__SDMMC0_DAT3>,
+ <PIN_PA6__SDMMC0_DAT4>,
+ <PIN_PA7__SDMMC0_DAT5>,
+ <PIN_PA8__SDMMC0_DAT6>,
+ <PIN_PA9__SDMMC0_DAT7>;
+ bias-disable;
+ };
+
+ ck_cd_rstn_vddsel {
+ pinmux = <PIN_PA0__SDMMC0_CK>,
+ <PIN_PA10__SDMMC0_RSTN>,
+ <PIN_PA11__SDMMC0_VDDSEL>,
+ <PIN_PA13__SDMMC0_CD>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdmmc1_default: sdmmc1_default {
+ cmd_data {
+ pinmux = <PIN_PA28__SDMMC1_CMD>,
+ <PIN_PA18__SDMMC1_DAT0>,
+ <PIN_PA19__SDMMC1_DAT1>,
+ <PIN_PA20__SDMMC1_DAT2>,
+ <PIN_PA21__SDMMC1_DAT3>;
+ bias-disable;
+ };
+
+ conf-ck_cd {
+ pinmux = <PIN_PA22__SDMMC1_CK>,
+ <PIN_PA30__SDMMC1_CD>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_spi0_default: spi0_default {
+ pinmux = <PIN_PA14__SPI0_SPCK>,
+ <PIN_PA15__SPI0_MOSI>,
+ <PIN_PA16__SPI0_MISO>,
+ <PIN_PA17__SPI0_NPCS0>;
+ bias-disable;
+ };
+
+ pinctrl_uart1_default: uart1_default {
+ pinmux = <PIN_PD2__URXD1>,
+ <PIN_PD3__UTXD1>;
+ bias-disable;
+ };
+
+ pinctrl_uart3_default: uart3_default {
+ pinmux = <PIN_PB11__URXD3>,
+ <PIN_PB12__UTXD3>;
+ bias-disable;
+ };
+
+ pinctrl_usb_default: usb_default {
+ pinmux = <PIN_PB10__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ pinmux = <PIN_PA31__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_pwm0_pwm2_default: pwm0_pwm2_default {
+ pinmux = <PIN_PB5__PWMH2>,
+ <PIN_PB6__PWML2>;
+ bias-pull-up;
+ };
+ };
+
+ classd: classd@fc048000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_classd_default>;
+ atmel,pwm-type = "diff";
+ atmel,non-overlap-time = <10>;
+ status = "okay";
+ };
+
+ i2s1: i2s@fc04c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2s1_default>;
+ status = "disabled"; /* conflict with spi0, sdmmc1 */
+ };
+
+ can1: can@fc050000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_default>;
+ status = "okay";
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+ bp1 {
+ label = "PB_USER";
+ gpios = <&pioA PIN_PB9 GPIO_ACTIVE_LOW>;
+ linux,code = <0x104>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led_gpio_default>;
+ status = "okay"; /* conflict with pwm0 */
+
+ red {
+ label = "red";
+ gpios = <&pioA PIN_PB6 GPIO_ACTIVE_LOW>;
+ };
+
+
+ green {
+ label = "green";
+ gpios = <&pioA PIN_PB5 GPIO_ACTIVE_LOW>;
+ };
+
+ blue {
+ label = "blue";
+ gpios = <&pioA PIN_PB0 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};