ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/linux/arch/arm/boot/dts/imx28-duckbill.dts b/marvell/linux/arch/arm/boot/dts/imx28-duckbill.dts
new file mode 100644
index 0000000..c666afb
--- /dev/null
+++ b/marvell/linux/arch/arm/boot/dts/imx28-duckbill.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@heimpold.de>
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "I2SE Duckbill";
+ compatible = "i2se,duckbill", "fsl,imx28";
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: spi@80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <4>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ ssp2: spi@80014000 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: leds@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART1_RX__GPIO_3_4
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+ };
+
+ apbx@80040000 {
+ lradc@80050000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@80058000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+ };
+
+ auart0: serial@8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
+ duart: serial@80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy@8007c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ usb0: usb@80080000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ };
+
+ mac0: ethernet@800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ status = "okay";
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ status-red {
+ label = "duckbill:red:status";
+ gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};