diff --git a/marvell/linux/arch/m68k/coldfire/timers.c b/marvell/linux/arch/m68k/coldfire/timers.c
new file mode 100644
index 0000000..227aa5d
--- /dev/null
+++ b/marvell/linux/arch/m68k/coldfire/timers.c
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0
+/***************************************************************************/
+
+/*
+ *	timers.c -- generic ColdFire hardware timer support.
+ *
+ *	Copyright (C) 1999-2008, Greg Ungerer <gerg@snapgear.com>
+ */
+
+/***************************************************************************/
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/profile.h>
+#include <linux/clocksource.h>
+#include <asm/io.h>
+#include <asm/traps.h>
+#include <asm/machdep.h>
+#include <asm/coldfire.h>
+#include <asm/mcftimer.h>
+#include <asm/mcfsim.h>
+
+/***************************************************************************/
+
+/*
+ *	By default use timer1 as the system clock timer.
+ */
+#define	FREQ	(MCF_BUSCLK / 16)
+#define	TA(a)	(MCFTIMER_BASE1 + (a))
+
+/*
+ *	These provide the underlying interrupt vector support.
+ *	Unfortunately it is a little different on each ColdFire.
+ */
+void coldfire_profile_init(void);
+
+#if defined(CONFIG_M53xx) || defined(CONFIG_M5441x)
+#define	__raw_readtrr	__raw_readl
+#define	__raw_writetrr	__raw_writel
+#else
+#define	__raw_readtrr	__raw_readw
+#define	__raw_writetrr	__raw_writew
+#endif
+
+static u32 mcftmr_cycles_per_jiffy;
+static u32 mcftmr_cnt;
+
+static irq_handler_t timer_interrupt;
+
+/***************************************************************************/
+
+static void init_timer_irq(void)
+{
+#ifdef MCFSIM_ICR_AUTOVEC
+	/* Timer1 is always used as system timer */
+	writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL6 | MCFSIM_ICR_PRI3,
+		MCFSIM_TIMER1ICR);
+	mcf_mapirq2imr(MCF_IRQ_TIMER, MCFINTC_TIMER1);
+
+#ifdef CONFIG_HIGHPROFILE
+	/* Timer2 is to be used as a high speed profile timer  */
+	writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL7 | MCFSIM_ICR_PRI3,
+		MCFSIM_TIMER2ICR);
+	mcf_mapirq2imr(MCF_IRQ_PROFILER, MCFINTC_TIMER2);
+#endif
+#endif /* MCFSIM_ICR_AUTOVEC */
+}
+
+/***************************************************************************/
+
+static irqreturn_t mcftmr_tick(int irq, void *dummy)
+{
+	/* Reset the ColdFire timer */
+	__raw_writeb(MCFTIMER_TER_CAP | MCFTIMER_TER_REF, TA(MCFTIMER_TER));
+
+	mcftmr_cnt += mcftmr_cycles_per_jiffy;
+	return timer_interrupt(irq, dummy);
+}
+
+/***************************************************************************/
+
+static struct irqaction mcftmr_timer_irq = {
+	.name	 = "timer",
+	.flags	 = IRQF_TIMER,
+	.handler = mcftmr_tick,
+};
+
+/***************************************************************************/
+
+static u64 mcftmr_read_clk(struct clocksource *cs)
+{
+	unsigned long flags;
+	u32 cycles;
+	u16 tcn;
+
+	local_irq_save(flags);
+	tcn = __raw_readw(TA(MCFTIMER_TCN));
+	cycles = mcftmr_cnt;
+	local_irq_restore(flags);
+
+	return cycles + tcn;
+}
+
+/***************************************************************************/
+
+static struct clocksource mcftmr_clk = {
+	.name	= "tmr",
+	.rating	= 250,
+	.read	= mcftmr_read_clk,
+	.mask	= CLOCKSOURCE_MASK(32),
+	.flags	= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+/***************************************************************************/
+
+void hw_timer_init(irq_handler_t handler)
+{
+	__raw_writew(MCFTIMER_TMR_DISABLE, TA(MCFTIMER_TMR));
+	mcftmr_cycles_per_jiffy = FREQ / HZ;
+	/*
+	 *	The coldfire timer runs from 0 to TRR included, then 0
+	 *	again and so on.  It counts thus actually TRR + 1 steps
+	 *	for 1 tick, not TRR.  So if you want n cycles,
+	 *	initialize TRR with n - 1.
+	 */
+	__raw_writetrr(mcftmr_cycles_per_jiffy - 1, TA(MCFTIMER_TRR));
+	__raw_writew(MCFTIMER_TMR_ENORI | MCFTIMER_TMR_CLK16 |
+		MCFTIMER_TMR_RESTART | MCFTIMER_TMR_ENABLE, TA(MCFTIMER_TMR));
+
+	clocksource_register_hz(&mcftmr_clk, FREQ);
+
+	timer_interrupt = handler;
+	init_timer_irq();
+	setup_irq(MCF_IRQ_TIMER, &mcftmr_timer_irq);
+
+#ifdef CONFIG_HIGHPROFILE
+	coldfire_profile_init();
+#endif
+}
+
+/***************************************************************************/
+#ifdef CONFIG_HIGHPROFILE
+/***************************************************************************/
+
+/*
+ *	By default use timer2 as the profiler clock timer.
+ */
+#define	PA(a)	(MCFTIMER_BASE2 + (a))
+
+/*
+ *	Choose a reasonably fast profile timer. Make it an odd value to
+ *	try and get good coverage of kernel operations.
+ */
+#define	PROFILEHZ	1013
+
+/*
+ *	Use the other timer to provide high accuracy profiling info.
+ */
+irqreturn_t coldfire_profile_tick(int irq, void *dummy)
+{
+	/* Reset ColdFire timer2 */
+	__raw_writeb(MCFTIMER_TER_CAP | MCFTIMER_TER_REF, PA(MCFTIMER_TER));
+	if (current->pid)
+		profile_tick(CPU_PROFILING);
+	return IRQ_HANDLED;
+}
+
+/***************************************************************************/
+
+static struct irqaction coldfire_profile_irq = {
+	.name	 = "profile timer",
+	.flags	 = IRQF_TIMER,
+	.handler = coldfire_profile_tick,
+};
+
+void coldfire_profile_init(void)
+{
+	printk(KERN_INFO "PROFILE: lodging TIMER2 @ %dHz as profile timer\n",
+	       PROFILEHZ);
+
+	/* Set up TIMER 2 as high speed profile clock */
+	__raw_writew(MCFTIMER_TMR_DISABLE, PA(MCFTIMER_TMR));
+
+	__raw_writetrr(((MCF_BUSCLK / 16) / PROFILEHZ), PA(MCFTIMER_TRR));
+	__raw_writew(MCFTIMER_TMR_ENORI | MCFTIMER_TMR_CLK16 |
+		MCFTIMER_TMR_RESTART | MCFTIMER_TMR_ENABLE, PA(MCFTIMER_TMR));
+
+	setup_irq(MCF_IRQ_PROFILER, &coldfire_profile_irq);
+}
+
+/***************************************************************************/
+#endif	/* CONFIG_HIGHPROFILE */
+/***************************************************************************/