ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/linux/arch/powerpc/boot/dts/mpc832x_mds.dts b/marvell/linux/arch/powerpc/boot/dts/mpc832x_mds.dts
new file mode 100644
index 0000000..3af073f
--- /dev/null
+++ b/marvell/linux/arch/powerpc/boot/dts/mpc832x_mds.dts
@@ -0,0 +1,436 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * MPC8323E EMDS Device Tree Source
+ *
+ * Copyright 2006 Freescale Semiconductor Inc.
+ *
+
+ * To enable external serial I/O on a Freescale MPC 8323 SYS/MDS board, do
+ * this:
+ *
+ * 1) On chip U61, lift (disconnect) pins 21 (TXD) and 22 (RXD) from the board.
+ * 2) Solder a wire from U61-21 to P19A-23. P19 is a grid of pins on the board
+ * next to the serial ports.
+ * 3) Solder a wire from U61-22 to P19K-22.
+ *
+ * Note that there's a typo in the schematic. The board labels the last column
+ * of pins "P19K", but in the schematic, that column is called "P19J". So if
+ * you're going by the schematic, the pin is called "P19J-K22".
+ */
+
+/dts-v1/;
+
+/ {
+ model = "MPC8323EMDS";
+ compatible = "MPC8323EMDS", "MPC832xMDS", "MPC83xxMDS";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ serial0 = &serial0;
+ serial1 = &serial1;
+ pci0 = &pci0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8323@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <16384>; // L1, 16K
+ i-cache-size = <16384>; // L1, 16K
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x08000000>;
+ };
+
+ bcsr@f8000000 {
+ compatible = "fsl,mpc8323mds-bcsr";
+ reg = <0xf8000000 0x8000>;
+ };
+
+ soc8323@e0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+ ranges = <0x0 0xe0000000 0x00100000>;
+ reg = <0xe0000000 0x00000200>;
+ bus-frequency = <132000000>;
+
+ wdt@200 {
+ device_type = "watchdog";
+ compatible = "mpc83xx_wdt";
+ reg = <0x200 0x100>;
+ };
+
+ pmc: power@b00 {
+ compatible = "fsl,mpc8323-pmc", "fsl,mpc8349-pmc";
+ reg = <0xb00 0x100 0xa00 0x100>;
+ interrupts = <80 0x8>;
+ interrupt-parent = <&ipic>;
+ };
+
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <14 0x8>;
+ interrupt-parent = <&ipic>;
+ dfsrr;
+
+ rtc@68 {
+ compatible = "dallas,ds1374";
+ reg = <0x68>;
+ };
+ };
+
+ serial0: serial@4500 {
+ cell-index = <0>;
+ device_type = "serial";
+ compatible = "fsl,ns16550", "ns16550";
+ reg = <0x4500 0x100>;
+ clock-frequency = <0>;
+ interrupts = <9 0x8>;
+ interrupt-parent = <&ipic>;
+ };
+
+ serial1: serial@4600 {
+ cell-index = <1>;
+ device_type = "serial";
+ compatible = "fsl,ns16550", "ns16550";
+ reg = <0x4600 0x100>;
+ clock-frequency = <0>;
+ interrupts = <10 0x8>;
+ interrupt-parent = <&ipic>;
+ };
+
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8323-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ cell-index = <3>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
+ crypto@30000 {
+ compatible = "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
+ reg = <0x30000 0x10000>;
+ interrupts = <11 0x8>;
+ interrupt-parent = <&ipic>;
+ fsl,num-channels = <1>;
+ fsl,channel-fifo-len = <24>;
+ fsl,exec-units-mask = <0x4c>;
+ fsl,descriptor-types-mask = <0x0122003f>;
+ sleep = <&pmc 0x03000000>;
+ };
+
+ ipic: pic@700 {
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0x700 0x100>;
+ device_type = "ipic";
+ };
+
+ par_io@1400 {
+ reg = <0x1400 0x100>;
+ device_type = "par_io";
+ num-ports = <7>;
+
+ pio3: ucc_pin@3 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 3 4 3 0 2 0 /* MDIO */
+ 3 5 1 0 2 0 /* MDC */
+ 0 13 2 0 1 0 /* RX_CLK (CLK9) */
+ 3 24 2 0 1 0 /* TX_CLK (CLK10) */
+ 1 0 1 0 1 0 /* TxD0 */
+ 1 1 1 0 1 0 /* TxD1 */
+ 1 2 1 0 1 0 /* TxD2 */
+ 1 3 1 0 1 0 /* TxD3 */
+ 1 4 2 0 1 0 /* RxD0 */
+ 1 5 2 0 1 0 /* RxD1 */
+ 1 6 2 0 1 0 /* RxD2 */
+ 1 7 2 0 1 0 /* RxD3 */
+ 1 8 2 0 1 0 /* RX_ER */
+ 1 9 1 0 1 0 /* TX_ER */
+ 1 10 2 0 1 0 /* RX_DV */
+ 1 11 2 0 1 0 /* COL */
+ 1 12 1 0 1 0 /* TX_EN */
+ 1 13 2 0 1 0>; /* CRS */
+ };
+ pio4: ucc_pin@4 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 3 31 2 0 1 0 /* RX_CLK (CLK7) */
+ 3 6 2 0 1 0 /* TX_CLK (CLK8) */
+ 1 18 1 0 1 0 /* TxD0 */
+ 1 19 1 0 1 0 /* TxD1 */
+ 1 20 1 0 1 0 /* TxD2 */
+ 1 21 1 0 1 0 /* TxD3 */
+ 1 22 2 0 1 0 /* RxD0 */
+ 1 23 2 0 1 0 /* RxD1 */
+ 1 24 2 0 1 0 /* RxD2 */
+ 1 25 2 0 1 0 /* RxD3 */
+ 1 26 2 0 1 0 /* RX_ER */
+ 1 27 1 0 1 0 /* TX_ER */
+ 1 28 2 0 1 0 /* RX_DV */
+ 1 29 2 0 1 0 /* COL */
+ 1 30 1 0 1 0 /* TX_EN */
+ 1 31 2 0 1 0>; /* CRS */
+ };
+ pio5: ucc_pin@5 {
+ pio-map = <
+ /*
+ * open has
+ * port pin dir drain sel irq
+ */
+ 2 0 1 0 2 0 /* TxD5 */
+ 2 8 2 0 2 0 /* RxD5 */
+
+ 2 29 2 0 0 0 /* CTS5 */
+ 2 31 1 0 2 0 /* RTS5 */
+
+ 2 24 2 0 0 0 /* CD */
+
+ >;
+ };
+
+ };
+ };
+
+ qe@e0100000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "qe";
+ compatible = "fsl,qe";
+ ranges = <0x0 0xe0100000 0x00100000>;
+ reg = <0xe0100000 0x480>;
+ brg-frequency = <0>;
+ bus-frequency = <198000000>;
+ fsl,qe-num-riscs = <1>;
+ fsl,qe-num-snums = <28>;
+
+ muram@10000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0x0 0x00010000 0x00004000>;
+
+ data-only@0 {
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0x0 0x4000>;
+ };
+ };
+
+ spi@4c0 {
+ cell-index = <0>;
+ compatible = "fsl,spi";
+ reg = <0x4c0 0x40>;
+ interrupts = <2>;
+ interrupt-parent = <&qeic>;
+ mode = "cpu";
+ };
+
+ spi@500 {
+ cell-index = <1>;
+ compatible = "fsl,spi";
+ reg = <0x500 0x40>;
+ interrupts = <1>;
+ interrupt-parent = <&qeic>;
+ mode = "cpu";
+ };
+
+ usb@6c0 {
+ compatible = "qe_udc";
+ reg = <0x6c0 0x40 0x8b00 0x100>;
+ interrupts = <11>;
+ interrupt-parent = <&qeic>;
+ mode = "slave";
+ };
+
+ enet0: ucc@2200 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <3>;
+ reg = <0x2200 0x200>;
+ interrupts = <34>;
+ interrupt-parent = <&qeic>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ rx-clock-name = "clk9";
+ tx-clock-name = "clk10";
+ phy-handle = <&phy3>;
+ pio-handle = <&pio3>;
+ };
+
+ enet1: ucc@3200 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <4>;
+ reg = <0x3200 0x200>;
+ interrupts = <35>;
+ interrupt-parent = <&qeic>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ rx-clock-name = "clk7";
+ tx-clock-name = "clk8";
+ phy-handle = <&phy4>;
+ pio-handle = <&pio4>;
+ };
+
+ ucc@2400 {
+ device_type = "serial";
+ compatible = "ucc_uart";
+ cell-index = <5>; /* The UCC number, 1-7*/
+ port-number = <0>; /* Which ttyQEx device */
+ soft-uart; /* We need Soft-UART */
+ reg = <0x2400 0x200>;
+ interrupts = <40>; /* From Table 18-12 */
+ interrupt-parent = < &qeic >;
+ /*
+ * For Soft-UART, we need to set TX to 1X, which
+ * means specifying separate clock sources.
+ */
+ rx-clock-name = "brg5";
+ tx-clock-name = "brg6";
+ pio-handle = < &pio5 >;
+ };
+
+
+ mdio@2320 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2320 0x18>;
+ compatible = "fsl,ucc-mdio";
+
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x3>;
+ };
+ phy4: ethernet-phy@4 {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x4>;
+ };
+ };
+
+ qeic: interrupt-controller@80 {
+ interrupt-controller;
+ compatible = "fsl,qe-ic";
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ reg = <0x80 0x80>;
+ big-endian;
+ interrupts = <32 0x8 33 0x8>; //high:32 low:33
+ interrupt-parent = <&ipic>;
+ };
+ };
+
+ pci0: pci@e0008500 {
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+ /* IDSEL 0x11 AD17 */
+ 0x8800 0x0 0x0 0x1 &ipic 20 0x8
+ 0x8800 0x0 0x0 0x2 &ipic 21 0x8
+ 0x8800 0x0 0x0 0x3 &ipic 22 0x8
+ 0x8800 0x0 0x0 0x4 &ipic 23 0x8
+
+ /* IDSEL 0x12 AD18 */
+ 0x9000 0x0 0x0 0x1 &ipic 22 0x8
+ 0x9000 0x0 0x0 0x2 &ipic 23 0x8
+ 0x9000 0x0 0x0 0x3 &ipic 20 0x8
+ 0x9000 0x0 0x0 0x4 &ipic 21 0x8
+
+ /* IDSEL 0x13 AD19 */
+ 0x9800 0x0 0x0 0x1 &ipic 23 0x8
+ 0x9800 0x0 0x0 0x2 &ipic 20 0x8
+ 0x9800 0x0 0x0 0x3 &ipic 21 0x8
+ 0x9800 0x0 0x0 0x4 &ipic 22 0x8
+
+ /* IDSEL 0x15 AD21*/
+ 0xa800 0x0 0x0 0x1 &ipic 20 0x8
+ 0xa800 0x0 0x0 0x2 &ipic 21 0x8
+ 0xa800 0x0 0x0 0x3 &ipic 22 0x8
+ 0xa800 0x0 0x0 0x4 &ipic 23 0x8
+
+ /* IDSEL 0x16 AD22*/
+ 0xb000 0x0 0x0 0x1 &ipic 23 0x8
+ 0xb000 0x0 0x0 0x2 &ipic 20 0x8
+ 0xb000 0x0 0x0 0x3 &ipic 21 0x8
+ 0xb000 0x0 0x0 0x4 &ipic 22 0x8
+
+ /* IDSEL 0x17 AD23*/
+ 0xb800 0x0 0x0 0x1 &ipic 22 0x8
+ 0xb800 0x0 0x0 0x2 &ipic 23 0x8
+ 0xb800 0x0 0x0 0x3 &ipic 20 0x8
+ 0xb800 0x0 0x0 0x4 &ipic 21 0x8
+
+ /* IDSEL 0x18 AD24*/
+ 0xc000 0x0 0x0 0x1 &ipic 21 0x8
+ 0xc000 0x0 0x0 0x2 &ipic 22 0x8
+ 0xc000 0x0 0x0 0x3 &ipic 23 0x8
+ 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <66 0x8>;
+ bus-range = <0x0 0x0>;
+ ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
+ 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
+ 0x01000000 0x0 0x00000000 0xd0000000 0x0 0x00100000>;
+ clock-frequency = <0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0xe0008500 0x100 /* internal registers */
+ 0xe0008300 0x8>; /* config space access registers */
+ compatible = "fsl,mpc8349-pci";
+ device_type = "pci";
+ sleep = <&pmc 0x00010000>;
+ };
+};