ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/linux/drivers/i2c/busses/i2c-designware-common.c b/marvell/linux/drivers/i2c/busses/i2c-designware-common.c
new file mode 100644
index 0000000..c903667
--- /dev/null
+++ b/marvell/linux/drivers/i2c/busses/i2c-designware-common.c
@@ -0,0 +1,373 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Synopsys DesignWare I2C adapter driver.
+ *
+ * Based on the TI DAVINCI I2C adapter driver.
+ *
+ * Copyright (C) 2006 Texas Instruments.
+ * Copyright (C) 2007 MontaVista Software Inc.
+ * Copyright (C) 2009 Provigent Ltd.
+ */
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/export.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/swab.h>
+
+#include "i2c-designware-core.h"
+
+static char *abort_sources[] = {
+ [ABRT_7B_ADDR_NOACK] =
+ "slave address not acknowledged (7bit mode)",
+ [ABRT_10ADDR1_NOACK] =
+ "first address byte not acknowledged (10bit mode)",
+ [ABRT_10ADDR2_NOACK] =
+ "second address byte not acknowledged (10bit mode)",
+ [ABRT_TXDATA_NOACK] =
+ "data not acknowledged",
+ [ABRT_GCALL_NOACK] =
+ "no acknowledgement for a general call",
+ [ABRT_GCALL_READ] =
+ "read after general call",
+ [ABRT_SBYTE_ACKDET] =
+ "start byte acknowledged",
+ [ABRT_SBYTE_NORSTRT] =
+ "trying to send start byte when restart is disabled",
+ [ABRT_10B_RD_NORSTRT] =
+ "trying to read when restart is disabled (10bit mode)",
+ [ABRT_MASTER_DIS] =
+ "trying to use disabled adapter",
+ [ARB_LOST] =
+ "lost arbitration",
+ [ABRT_SLAVE_FLUSH_TXFIFO] =
+ "read command so flush old data in the TX FIFO",
+ [ABRT_SLAVE_ARBLOST] =
+ "slave lost the bus while transmitting data to a remote master",
+ [ABRT_SLAVE_RD_INTX] =
+ "incorrect slave-transmitter mode configuration",
+};
+
+u32 dw_readl(struct dw_i2c_dev *dev, int offset)
+{
+ u32 value;
+
+ if (dev->flags & ACCESS_16BIT)
+ value = readw_relaxed(dev->base + offset) |
+ (readw_relaxed(dev->base + offset + 2) << 16);
+ else
+ value = readl_relaxed(dev->base + offset);
+
+ if (dev->flags & ACCESS_SWAP)
+ return swab32(value);
+ else
+ return value;
+}
+
+void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset)
+{
+ if (dev->flags & ACCESS_SWAP)
+ b = swab32(b);
+
+ if (dev->flags & ACCESS_16BIT) {
+ writew_relaxed((u16)b, dev->base + offset);
+ writew_relaxed((u16)(b >> 16), dev->base + offset + 2);
+ } else {
+ writel_relaxed(b, dev->base + offset);
+ }
+}
+
+/**
+ * i2c_dw_set_reg_access() - Set register access flags
+ * @dev: device private data
+ *
+ * Autodetects needed register access mode and sets access flags accordingly.
+ * This must be called before doing any other register access.
+ */
+int i2c_dw_set_reg_access(struct dw_i2c_dev *dev)
+{
+ u32 reg;
+ int ret;
+
+ ret = i2c_dw_acquire_lock(dev);
+ if (ret)
+ return ret;
+
+ reg = dw_readl(dev, DW_IC_COMP_TYPE);
+ i2c_dw_release_lock(dev);
+
+ if (reg == swab32(DW_IC_COMP_TYPE_VALUE)) {
+ /* Configure register endianess access */
+ dev->flags |= ACCESS_SWAP;
+ } else if (reg == (DW_IC_COMP_TYPE_VALUE & 0x0000ffff)) {
+ /* Configure register access mode 16bit */
+ dev->flags |= ACCESS_16BIT;
+ } else if (reg != DW_IC_COMP_TYPE_VALUE) {
+ dev_err(dev->dev,
+ "Unknown Synopsys component type: 0x%08x\n", reg);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+u32 i2c_dw_scl_hcnt(u32 ic_clk, u32 tSYMBOL, u32 tf, int cond, int offset)
+{
+ /*
+ * DesignWare I2C core doesn't seem to have solid strategy to meet
+ * the tHD;STA timing spec. Configuring _HCNT based on tHIGH spec
+ * will result in violation of the tHD;STA spec.
+ */
+ if (cond)
+ /*
+ * Conditional expression:
+ *
+ * IC_[FS]S_SCL_HCNT + (1+4+3) >= IC_CLK * tHIGH
+ *
+ * This is based on the DW manuals, and represents an ideal
+ * configuration. The resulting I2C bus speed will be
+ * faster than any of the others.
+ *
+ * If your hardware is free from tHD;STA issue, try this one.
+ */
+ return (ic_clk * tSYMBOL + 500000) / 1000000 - 8 + offset;
+ else
+ /*
+ * Conditional expression:
+ *
+ * IC_[FS]S_SCL_HCNT + 3 >= IC_CLK * (tHD;STA + tf)
+ *
+ * This is just experimental rule; the tHD;STA period turned
+ * out to be proportinal to (_HCNT + 3). With this setting,
+ * we could meet both tHIGH and tHD;STA timing specs.
+ *
+ * If unsure, you'd better to take this alternative.
+ *
+ * The reason why we need to take into account "tf" here,
+ * is the same as described in i2c_dw_scl_lcnt().
+ */
+ return (ic_clk * (tSYMBOL + tf) + 500000) / 1000000
+ - 3 + offset;
+}
+
+u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset)
+{
+ /*
+ * Conditional expression:
+ *
+ * IC_[FS]S_SCL_LCNT + 1 >= IC_CLK * (tLOW + tf)
+ *
+ * DW I2C core starts counting the SCL CNTs for the LOW period
+ * of the SCL clock (tLOW) as soon as it pulls the SCL line.
+ * In order to meet the tLOW timing spec, we need to take into
+ * account the fall time of SCL signal (tf). Default tf value
+ * should be 0.3 us, for safety.
+ */
+ return ((ic_clk * (tLOW + tf) + 500000) / 1000000) - 1 + offset;
+}
+
+int i2c_dw_set_sda_hold(struct dw_i2c_dev *dev)
+{
+ u32 reg;
+ int ret;
+
+ ret = i2c_dw_acquire_lock(dev);
+ if (ret)
+ return ret;
+
+ /* Configure SDA Hold Time if required */
+ reg = dw_readl(dev, DW_IC_COMP_VERSION);
+ if (reg >= DW_IC_SDA_HOLD_MIN_VERS) {
+ if (!dev->sda_hold_time) {
+ /* Keep previous hold time setting if no one set it */
+ dev->sda_hold_time = dw_readl(dev, DW_IC_SDA_HOLD);
+ }
+
+ /*
+ * Workaround for avoiding TX arbitration lost in case I2C
+ * slave pulls SDA down "too quickly" after falling egde of
+ * SCL by enabling non-zero SDA RX hold. Specification says it
+ * extends incoming SDA low to high transition while SCL is
+ * high but it apprears to help also above issue.
+ */
+ if (!(dev->sda_hold_time & DW_IC_SDA_HOLD_RX_MASK))
+ dev->sda_hold_time |= 1 << DW_IC_SDA_HOLD_RX_SHIFT;
+
+ dev_dbg(dev->dev, "SDA Hold Time TX:RX = %d:%d\n",
+ dev->sda_hold_time & ~(u32)DW_IC_SDA_HOLD_RX_MASK,
+ dev->sda_hold_time >> DW_IC_SDA_HOLD_RX_SHIFT);
+ } else if (dev->set_sda_hold_time) {
+ dev->set_sda_hold_time(dev);
+ } else if (dev->sda_hold_time) {
+ dev_warn(dev->dev,
+ "Hardware too old to adjust SDA hold time.\n");
+ dev->sda_hold_time = 0;
+ }
+
+ i2c_dw_release_lock(dev);
+
+ return 0;
+}
+
+void __i2c_dw_disable(struct dw_i2c_dev *dev)
+{
+ int timeout = 100;
+
+ do {
+ __i2c_dw_disable_nowait(dev);
+ /*
+ * The enable status register may be unimplemented, but
+ * in that case this test reads zero and exits the loop.
+ */
+ if ((dw_readl(dev, DW_IC_ENABLE_STATUS) & 1) == 0)
+ return;
+
+ /*
+ * Wait 10 times the signaling period of the highest I2C
+ * transfer supported by the driver (for 400KHz this is
+ * 25us) as described in the DesignWare I2C databook.
+ */
+ usleep_range(25, 250);
+ } while (timeout--);
+
+ dev_warn(dev->dev, "timeout in disabling adapter\n");
+}
+
+unsigned long i2c_dw_clk_rate(struct dw_i2c_dev *dev)
+{
+ /*
+ * Clock is not necessary if we got LCNT/HCNT values directly from
+ * the platform code.
+ */
+ if (WARN_ON_ONCE(!dev->get_clk_rate_khz))
+ return 0;
+ return dev->get_clk_rate_khz(dev);
+}
+
+int i2c_dw_prepare_clk(struct dw_i2c_dev *dev, bool prepare)
+{
+ int ret;
+
+ if (prepare) {
+ /* Optional interface clock */
+ ret = clk_prepare_enable(dev->pclk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(dev->clk);
+ if (ret)
+ clk_disable_unprepare(dev->pclk);
+
+ return ret;
+ }
+
+ clk_disable_unprepare(dev->clk);
+ clk_disable_unprepare(dev->pclk);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(i2c_dw_prepare_clk);
+
+int i2c_dw_acquire_lock(struct dw_i2c_dev *dev)
+{
+ int ret;
+
+ if (!dev->acquire_lock)
+ return 0;
+
+ ret = dev->acquire_lock();
+ if (!ret)
+ return 0;
+
+ dev_err(dev->dev, "couldn't acquire bus ownership\n");
+
+ return ret;
+}
+
+void i2c_dw_release_lock(struct dw_i2c_dev *dev)
+{
+ if (dev->release_lock)
+ dev->release_lock();
+}
+
+/*
+ * Waiting for bus not busy
+ */
+int i2c_dw_wait_bus_not_busy(struct dw_i2c_dev *dev)
+{
+ int timeout = TIMEOUT;
+
+ while (dw_readl(dev, DW_IC_STATUS) & DW_IC_STATUS_ACTIVITY) {
+ if (timeout <= 0) {
+ dev_warn(dev->dev, "timeout waiting for bus ready\n");
+ i2c_recover_bus(&dev->adapter);
+
+ if (dw_readl(dev, DW_IC_STATUS) & DW_IC_STATUS_ACTIVITY)
+ return -ETIMEDOUT;
+ return 0;
+ }
+ timeout--;
+ usleep_range(1000, 1100);
+ }
+
+ return 0;
+}
+
+int i2c_dw_handle_tx_abort(struct dw_i2c_dev *dev)
+{
+ unsigned long abort_source = dev->abort_source;
+ int i;
+
+ if (abort_source & DW_IC_TX_ABRT_NOACK) {
+ for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources))
+ dev_dbg(dev->dev,
+ "%s: %s\n", __func__, abort_sources[i]);
+ return -EREMOTEIO;
+ }
+
+ for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources))
+ dev_err(dev->dev, "%s: %s\n", __func__, abort_sources[i]);
+
+ if (abort_source & DW_IC_TX_ARB_LOST)
+ return -EAGAIN;
+ else if (abort_source & DW_IC_TX_ABRT_GCALL_READ)
+ return -EINVAL; /* wrong msgs[] data */
+ else
+ return -EIO;
+}
+
+u32 i2c_dw_func(struct i2c_adapter *adap)
+{
+ struct dw_i2c_dev *dev = i2c_get_adapdata(adap);
+
+ return dev->functionality;
+}
+
+void i2c_dw_disable(struct dw_i2c_dev *dev)
+{
+ /* Disable controller */
+ __i2c_dw_disable(dev);
+
+ /* Disable all interupts */
+ dw_writel(dev, 0, DW_IC_INTR_MASK);
+ dw_readl(dev, DW_IC_CLR_INTR);
+}
+
+void i2c_dw_disable_int(struct dw_i2c_dev *dev)
+{
+ dw_writel(dev, 0, DW_IC_INTR_MASK);
+}
+
+u32 i2c_dw_read_comp_param(struct dw_i2c_dev *dev)
+{
+ return dw_readl(dev, DW_IC_COMP_PARAM_1);
+}
+EXPORT_SYMBOL_GPL(i2c_dw_read_comp_param);
+
+MODULE_DESCRIPTION("Synopsys DesignWare I2C bus adapter core");
+MODULE_LICENSE("GPL");