ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/linux/drivers/net/dsa/microchip/Kconfig b/marvell/linux/drivers/net/dsa/microchip/Kconfig
new file mode 100644
index 0000000..1d7870c
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/Kconfig
@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config NET_DSA_MICROCHIP_KSZ_COMMON
+ tristate
+
+menuconfig NET_DSA_MICROCHIP_KSZ9477
+ tristate "Microchip KSZ9477 series switch support"
+ depends on NET_DSA
+ select NET_DSA_MICROCHIP_KSZ_COMMON
+ help
+ This driver adds support for Microchip KSZ9477 switch chips.
+
+config NET_DSA_MICROCHIP_KSZ9477_I2C
+ tristate "KSZ9477 series I2C connected switch driver"
+ depends on NET_DSA_MICROCHIP_KSZ9477 && I2C
+ select REGMAP_I2C
+ help
+ Select to enable support for registering switches configured through I2C.
+
+config NET_DSA_MICROCHIP_KSZ9477_SPI
+ tristate "KSZ9477 series SPI connected switch driver"
+ depends on NET_DSA_MICROCHIP_KSZ9477 && SPI
+ select REGMAP_SPI
+ help
+ Select to enable support for registering switches configured through SPI.
+
+menuconfig NET_DSA_MICROCHIP_KSZ8795
+ tristate "Microchip KSZ8795 series switch support"
+ depends on NET_DSA
+ select NET_DSA_MICROCHIP_KSZ_COMMON
+ help
+ This driver adds support for Microchip KSZ8795 switch chips.
+
+config NET_DSA_MICROCHIP_KSZ8795_SPI
+ tristate "KSZ8795 series SPI connected switch driver"
+ depends on NET_DSA_MICROCHIP_KSZ8795 && SPI
+ select REGMAP_SPI
+ help
+ This driver accesses KSZ8795 chip through SPI.
+
+ It is required to use the KSZ8795 switch driver as the only access
+ is through SPI.
diff --git a/marvell/linux/drivers/net/dsa/microchip/Makefile b/marvell/linux/drivers/net/dsa/microchip/Makefile
new file mode 100644
index 0000000..929caa8
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ_COMMON) += ksz_common.o
+obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477) += ksz9477.o
+obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477_I2C) += ksz9477_i2c.o
+obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477_SPI) += ksz9477_spi.o
+obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8795) += ksz8795.o
+obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8795_SPI) += ksz8795_spi.o
diff --git a/marvell/linux/drivers/net/dsa/microchip/ksz8795.c b/marvell/linux/drivers/net/dsa/microchip/ksz8795.c
new file mode 100644
index 0000000..7c17b0f
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/ksz8795.c
@@ -0,0 +1,1310 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Microchip KSZ8795 switch driver
+ *
+ * Copyright (C) 2017 Microchip Technology Inc.
+ * Tristram Ha <Tristram.Ha@microchip.com>
+ */
+
+#include <linux/delay.h>
+#include <linux/export.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_data/microchip-ksz.h>
+#include <linux/phy.h>
+#include <linux/etherdevice.h>
+#include <linux/if_bridge.h>
+#include <net/dsa.h>
+#include <net/switchdev.h>
+
+#include "ksz_common.h"
+#include "ksz8795_reg.h"
+
+static const struct {
+ char string[ETH_GSTRING_LEN];
+} mib_names[TOTAL_SWITCH_COUNTER_NUM] = {
+ { "rx_hi" },
+ { "rx_undersize" },
+ { "rx_fragments" },
+ { "rx_oversize" },
+ { "rx_jabbers" },
+ { "rx_symbol_err" },
+ { "rx_crc_err" },
+ { "rx_align_err" },
+ { "rx_mac_ctrl" },
+ { "rx_pause" },
+ { "rx_bcast" },
+ { "rx_mcast" },
+ { "rx_ucast" },
+ { "rx_64_or_less" },
+ { "rx_65_127" },
+ { "rx_128_255" },
+ { "rx_256_511" },
+ { "rx_512_1023" },
+ { "rx_1024_1522" },
+ { "rx_1523_2000" },
+ { "rx_2001" },
+ { "tx_hi" },
+ { "tx_late_col" },
+ { "tx_pause" },
+ { "tx_bcast" },
+ { "tx_mcast" },
+ { "tx_ucast" },
+ { "tx_deferred" },
+ { "tx_total_col" },
+ { "tx_exc_col" },
+ { "tx_single_col" },
+ { "tx_mult_col" },
+ { "rx_total" },
+ { "tx_total" },
+ { "rx_discards" },
+ { "tx_discards" },
+};
+
+static void ksz_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set)
+{
+ regmap_update_bits(dev->regmap[0], addr, bits, set ? bits : 0);
+}
+
+static void ksz_port_cfg(struct ksz_device *dev, int port, int offset, u8 bits,
+ bool set)
+{
+ regmap_update_bits(dev->regmap[0], PORT_CTRL_ADDR(port, offset),
+ bits, set ? bits : 0);
+}
+
+static int ksz8795_reset_switch(struct ksz_device *dev)
+{
+ /* reset switch */
+ ksz_write8(dev, REG_POWER_MANAGEMENT_1,
+ SW_SOFTWARE_POWER_DOWN << SW_POWER_MANAGEMENT_MODE_S);
+ ksz_write8(dev, REG_POWER_MANAGEMENT_1, 0);
+
+ return 0;
+}
+
+static void ksz8795_set_prio_queue(struct ksz_device *dev, int port, int queue)
+{
+ u8 hi, lo;
+
+ /* Number of queues can only be 1, 2, or 4. */
+ switch (queue) {
+ case 4:
+ case 3:
+ queue = PORT_QUEUE_SPLIT_4;
+ break;
+ case 2:
+ queue = PORT_QUEUE_SPLIT_2;
+ break;
+ default:
+ queue = PORT_QUEUE_SPLIT_1;
+ }
+ ksz_pread8(dev, port, REG_PORT_CTRL_0, &lo);
+ ksz_pread8(dev, port, P_DROP_TAG_CTRL, &hi);
+ lo &= ~PORT_QUEUE_SPLIT_L;
+ if (queue & PORT_QUEUE_SPLIT_2)
+ lo |= PORT_QUEUE_SPLIT_L;
+ hi &= ~PORT_QUEUE_SPLIT_H;
+ if (queue & PORT_QUEUE_SPLIT_4)
+ hi |= PORT_QUEUE_SPLIT_H;
+ ksz_pwrite8(dev, port, REG_PORT_CTRL_0, lo);
+ ksz_pwrite8(dev, port, P_DROP_TAG_CTRL, hi);
+
+ /* Default is port based for egress rate limit. */
+ if (queue != PORT_QUEUE_SPLIT_1)
+ ksz_cfg(dev, REG_SW_CTRL_19, SW_OUT_RATE_LIMIT_QUEUE_BASED,
+ true);
+}
+
+static void ksz8795_r_mib_cnt(struct ksz_device *dev, int port, u16 addr,
+ u64 *cnt)
+{
+ u16 ctrl_addr;
+ u32 data;
+ u8 check;
+ int loop;
+
+ ctrl_addr = addr + SWITCH_COUNTER_NUM * port;
+ ctrl_addr |= IND_ACC_TABLE(TABLE_MIB | TABLE_READ);
+
+ mutex_lock(&dev->alu_mutex);
+ ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
+
+ /* It is almost guaranteed to always read the valid bit because of
+ * slow SPI speed.
+ */
+ for (loop = 2; loop > 0; loop--) {
+ ksz_read8(dev, REG_IND_MIB_CHECK, &check);
+
+ if (check & MIB_COUNTER_VALID) {
+ ksz_read32(dev, REG_IND_DATA_LO, &data);
+ if (check & MIB_COUNTER_OVERFLOW)
+ *cnt += MIB_COUNTER_VALUE + 1;
+ *cnt += data & MIB_COUNTER_VALUE;
+ break;
+ }
+ }
+ mutex_unlock(&dev->alu_mutex);
+}
+
+static void ksz8795_r_mib_pkt(struct ksz_device *dev, int port, u16 addr,
+ u64 *dropped, u64 *cnt)
+{
+ u16 ctrl_addr;
+ u32 data;
+ u8 check;
+ int loop;
+
+ addr -= SWITCH_COUNTER_NUM;
+ ctrl_addr = (KS_MIB_TOTAL_RX_1 - KS_MIB_TOTAL_RX_0) * port;
+ ctrl_addr += addr + KS_MIB_TOTAL_RX_0;
+ ctrl_addr |= IND_ACC_TABLE(TABLE_MIB | TABLE_READ);
+
+ mutex_lock(&dev->alu_mutex);
+ ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
+
+ /* It is almost guaranteed to always read the valid bit because of
+ * slow SPI speed.
+ */
+ for (loop = 2; loop > 0; loop--) {
+ ksz_read8(dev, REG_IND_MIB_CHECK, &check);
+
+ if (check & MIB_COUNTER_VALID) {
+ ksz_read32(dev, REG_IND_DATA_LO, &data);
+ if (addr < 2) {
+ u64 total;
+
+ total = check & MIB_TOTAL_BYTES_H;
+ total <<= 32;
+ *cnt += total;
+ *cnt += data;
+ if (check & MIB_COUNTER_OVERFLOW) {
+ total = MIB_TOTAL_BYTES_H + 1;
+ total <<= 32;
+ *cnt += total;
+ }
+ } else {
+ if (check & MIB_COUNTER_OVERFLOW)
+ *cnt += MIB_PACKET_DROPPED + 1;
+ *cnt += data & MIB_PACKET_DROPPED;
+ }
+ break;
+ }
+ }
+ mutex_unlock(&dev->alu_mutex);
+}
+
+static void ksz8795_freeze_mib(struct ksz_device *dev, int port, bool freeze)
+{
+ /* enable the port for flush/freeze function */
+ if (freeze)
+ ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), true);
+ ksz_cfg(dev, REG_SW_CTRL_6, SW_MIB_COUNTER_FREEZE, freeze);
+
+ /* disable the port after freeze is done */
+ if (!freeze)
+ ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), false);
+}
+
+static void ksz8795_port_init_cnt(struct ksz_device *dev, int port)
+{
+ struct ksz_port_mib *mib = &dev->ports[port].mib;
+
+ /* flush all enabled port MIB counters */
+ ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), true);
+ ksz_cfg(dev, REG_SW_CTRL_6, SW_MIB_COUNTER_FLUSH, true);
+ ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), false);
+
+ mib->cnt_ptr = 0;
+
+ /* Some ports may not have MIB counters before SWITCH_COUNTER_NUM. */
+ while (mib->cnt_ptr < dev->reg_mib_cnt) {
+ dev->dev_ops->r_mib_cnt(dev, port, mib->cnt_ptr,
+ &mib->counters[mib->cnt_ptr]);
+ ++mib->cnt_ptr;
+ }
+
+ /* Some ports may not have MIB counters after SWITCH_COUNTER_NUM. */
+ while (mib->cnt_ptr < dev->mib_cnt) {
+ dev->dev_ops->r_mib_pkt(dev, port, mib->cnt_ptr,
+ NULL, &mib->counters[mib->cnt_ptr]);
+ ++mib->cnt_ptr;
+ }
+ mib->cnt_ptr = 0;
+ memset(mib->counters, 0, dev->mib_cnt * sizeof(u64));
+}
+
+static void ksz8795_r_table(struct ksz_device *dev, int table, u16 addr,
+ u64 *data)
+{
+ u16 ctrl_addr;
+
+ ctrl_addr = IND_ACC_TABLE(table | TABLE_READ) | addr;
+
+ mutex_lock(&dev->alu_mutex);
+ ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
+ ksz_read64(dev, REG_IND_DATA_HI, data);
+ mutex_unlock(&dev->alu_mutex);
+}
+
+static void ksz8795_w_table(struct ksz_device *dev, int table, u16 addr,
+ u64 data)
+{
+ u16 ctrl_addr;
+
+ ctrl_addr = IND_ACC_TABLE(table) | addr;
+
+ mutex_lock(&dev->alu_mutex);
+ ksz_write64(dev, REG_IND_DATA_HI, data);
+ ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
+ mutex_unlock(&dev->alu_mutex);
+}
+
+static int ksz8795_valid_dyn_entry(struct ksz_device *dev, u8 *data)
+{
+ int timeout = 100;
+
+ do {
+ ksz_read8(dev, REG_IND_DATA_CHECK, data);
+ timeout--;
+ } while ((*data & DYNAMIC_MAC_TABLE_NOT_READY) && timeout);
+
+ /* Entry is not ready for accessing. */
+ if (*data & DYNAMIC_MAC_TABLE_NOT_READY) {
+ return -EAGAIN;
+ /* Entry is ready for accessing. */
+ } else {
+ ksz_read8(dev, REG_IND_DATA_8, data);
+
+ /* There is no valid entry in the table. */
+ if (*data & DYNAMIC_MAC_TABLE_MAC_EMPTY)
+ return -ENXIO;
+ }
+ return 0;
+}
+
+static int ksz8795_r_dyn_mac_table(struct ksz_device *dev, u16 addr,
+ u8 *mac_addr, u8 *fid, u8 *src_port,
+ u8 *timestamp, u16 *entries)
+{
+ u32 data_hi, data_lo;
+ u16 ctrl_addr;
+ u8 data;
+ int rc;
+
+ ctrl_addr = IND_ACC_TABLE(TABLE_DYNAMIC_MAC | TABLE_READ) | addr;
+
+ mutex_lock(&dev->alu_mutex);
+ ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
+
+ rc = ksz8795_valid_dyn_entry(dev, &data);
+ if (rc == -EAGAIN) {
+ if (addr == 0)
+ *entries = 0;
+ } else if (rc == -ENXIO) {
+ *entries = 0;
+ /* At least one valid entry in the table. */
+ } else {
+ u64 buf = 0;
+ int cnt;
+
+ ksz_read64(dev, REG_IND_DATA_HI, &buf);
+ data_hi = (u32)(buf >> 32);
+ data_lo = (u32)buf;
+
+ /* Check out how many valid entry in the table. */
+ cnt = data & DYNAMIC_MAC_TABLE_ENTRIES_H;
+ cnt <<= DYNAMIC_MAC_ENTRIES_H_S;
+ cnt |= (data_hi & DYNAMIC_MAC_TABLE_ENTRIES) >>
+ DYNAMIC_MAC_ENTRIES_S;
+ *entries = cnt + 1;
+
+ *fid = (data_hi & DYNAMIC_MAC_TABLE_FID) >>
+ DYNAMIC_MAC_FID_S;
+ *src_port = (data_hi & DYNAMIC_MAC_TABLE_SRC_PORT) >>
+ DYNAMIC_MAC_SRC_PORT_S;
+ *timestamp = (data_hi & DYNAMIC_MAC_TABLE_TIMESTAMP) >>
+ DYNAMIC_MAC_TIMESTAMP_S;
+
+ mac_addr[5] = (u8)data_lo;
+ mac_addr[4] = (u8)(data_lo >> 8);
+ mac_addr[3] = (u8)(data_lo >> 16);
+ mac_addr[2] = (u8)(data_lo >> 24);
+
+ mac_addr[1] = (u8)data_hi;
+ mac_addr[0] = (u8)(data_hi >> 8);
+ rc = 0;
+ }
+ mutex_unlock(&dev->alu_mutex);
+
+ return rc;
+}
+
+static int ksz8795_r_sta_mac_table(struct ksz_device *dev, u16 addr,
+ struct alu_struct *alu)
+{
+ u32 data_hi, data_lo;
+ u64 data;
+
+ ksz8795_r_table(dev, TABLE_STATIC_MAC, addr, &data);
+ data_hi = data >> 32;
+ data_lo = (u32)data;
+ if (data_hi & (STATIC_MAC_TABLE_VALID | STATIC_MAC_TABLE_OVERRIDE)) {
+ alu->mac[5] = (u8)data_lo;
+ alu->mac[4] = (u8)(data_lo >> 8);
+ alu->mac[3] = (u8)(data_lo >> 16);
+ alu->mac[2] = (u8)(data_lo >> 24);
+ alu->mac[1] = (u8)data_hi;
+ alu->mac[0] = (u8)(data_hi >> 8);
+ alu->port_forward = (data_hi & STATIC_MAC_TABLE_FWD_PORTS) >>
+ STATIC_MAC_FWD_PORTS_S;
+ alu->is_override =
+ (data_hi & STATIC_MAC_TABLE_OVERRIDE) ? 1 : 0;
+ data_hi >>= 1;
+ alu->is_use_fid = (data_hi & STATIC_MAC_TABLE_USE_FID) ? 1 : 0;
+ alu->fid = (data_hi & STATIC_MAC_TABLE_FID) >>
+ STATIC_MAC_FID_S;
+ return 0;
+ }
+ return -ENXIO;
+}
+
+static void ksz8795_w_sta_mac_table(struct ksz_device *dev, u16 addr,
+ struct alu_struct *alu)
+{
+ u32 data_hi, data_lo;
+ u64 data;
+
+ data_lo = ((u32)alu->mac[2] << 24) |
+ ((u32)alu->mac[3] << 16) |
+ ((u32)alu->mac[4] << 8) | alu->mac[5];
+ data_hi = ((u32)alu->mac[0] << 8) | alu->mac[1];
+ data_hi |= (u32)alu->port_forward << STATIC_MAC_FWD_PORTS_S;
+
+ if (alu->is_override)
+ data_hi |= STATIC_MAC_TABLE_OVERRIDE;
+ if (alu->is_use_fid) {
+ data_hi |= STATIC_MAC_TABLE_USE_FID;
+ data_hi |= (u32)alu->fid << STATIC_MAC_FID_S;
+ }
+ if (alu->is_static)
+ data_hi |= STATIC_MAC_TABLE_VALID;
+ else
+ data_hi &= ~STATIC_MAC_TABLE_OVERRIDE;
+
+ data = (u64)data_hi << 32 | data_lo;
+ ksz8795_w_table(dev, TABLE_STATIC_MAC, addr, data);
+}
+
+static void ksz8795_from_vlan(u16 vlan, u8 *fid, u8 *member, u8 *valid)
+{
+ *fid = vlan & VLAN_TABLE_FID;
+ *member = (vlan & VLAN_TABLE_MEMBERSHIP) >> VLAN_TABLE_MEMBERSHIP_S;
+ *valid = !!(vlan & VLAN_TABLE_VALID);
+}
+
+static void ksz8795_to_vlan(u8 fid, u8 member, u8 valid, u16 *vlan)
+{
+ *vlan = fid;
+ *vlan |= (u16)member << VLAN_TABLE_MEMBERSHIP_S;
+ if (valid)
+ *vlan |= VLAN_TABLE_VALID;
+}
+
+static void ksz8795_r_vlan_entries(struct ksz_device *dev, u16 addr)
+{
+ u64 data;
+ int i;
+
+ ksz8795_r_table(dev, TABLE_VLAN, addr, &data);
+ addr *= 4;
+ for (i = 0; i < 4; i++) {
+ dev->vlan_cache[addr + i].table[0] = (u16)data;
+ data >>= VLAN_TABLE_S;
+ }
+}
+
+static void ksz8795_r_vlan_table(struct ksz_device *dev, u16 vid, u16 *vlan)
+{
+ int index;
+ u16 *data;
+ u16 addr;
+ u64 buf;
+
+ data = (u16 *)&buf;
+ addr = vid / 4;
+ index = vid & 3;
+ ksz8795_r_table(dev, TABLE_VLAN, addr, &buf);
+ *vlan = data[index];
+}
+
+static void ksz8795_w_vlan_table(struct ksz_device *dev, u16 vid, u16 vlan)
+{
+ int index;
+ u16 *data;
+ u16 addr;
+ u64 buf;
+
+ data = (u16 *)&buf;
+ addr = vid / 4;
+ index = vid & 3;
+ ksz8795_r_table(dev, TABLE_VLAN, addr, &buf);
+ data[index] = vlan;
+ dev->vlan_cache[vid].table[0] = vlan;
+ ksz8795_w_table(dev, TABLE_VLAN, addr, buf);
+}
+
+static void ksz8795_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
+{
+ u8 restart, speed, ctrl, link;
+ int processed = true;
+ u16 data = 0;
+ u8 p = phy;
+
+ switch (reg) {
+ case PHY_REG_CTRL:
+ ksz_pread8(dev, p, P_NEG_RESTART_CTRL, &restart);
+ ksz_pread8(dev, p, P_SPEED_STATUS, &speed);
+ ksz_pread8(dev, p, P_FORCE_CTRL, &ctrl);
+ if (restart & PORT_PHY_LOOPBACK)
+ data |= PHY_LOOPBACK;
+ if (ctrl & PORT_FORCE_100_MBIT)
+ data |= PHY_SPEED_100MBIT;
+ if (!(ctrl & PORT_AUTO_NEG_DISABLE))
+ data |= PHY_AUTO_NEG_ENABLE;
+ if (restart & PORT_POWER_DOWN)
+ data |= PHY_POWER_DOWN;
+ if (restart & PORT_AUTO_NEG_RESTART)
+ data |= PHY_AUTO_NEG_RESTART;
+ if (ctrl & PORT_FORCE_FULL_DUPLEX)
+ data |= PHY_FULL_DUPLEX;
+ if (speed & PORT_HP_MDIX)
+ data |= PHY_HP_MDIX;
+ if (restart & PORT_FORCE_MDIX)
+ data |= PHY_FORCE_MDIX;
+ if (restart & PORT_AUTO_MDIX_DISABLE)
+ data |= PHY_AUTO_MDIX_DISABLE;
+ if (restart & PORT_TX_DISABLE)
+ data |= PHY_TRANSMIT_DISABLE;
+ if (restart & PORT_LED_OFF)
+ data |= PHY_LED_DISABLE;
+ break;
+ case PHY_REG_STATUS:
+ ksz_pread8(dev, p, P_LINK_STATUS, &link);
+ data = PHY_100BTX_FD_CAPABLE |
+ PHY_100BTX_CAPABLE |
+ PHY_10BT_FD_CAPABLE |
+ PHY_10BT_CAPABLE |
+ PHY_AUTO_NEG_CAPABLE;
+ if (link & PORT_AUTO_NEG_COMPLETE)
+ data |= PHY_AUTO_NEG_ACKNOWLEDGE;
+ if (link & PORT_STAT_LINK_GOOD)
+ data |= PHY_LINK_STATUS;
+ break;
+ case PHY_REG_ID_1:
+ data = KSZ8795_ID_HI;
+ break;
+ case PHY_REG_ID_2:
+ data = KSZ8795_ID_LO;
+ break;
+ case PHY_REG_AUTO_NEGOTIATION:
+ ksz_pread8(dev, p, P_LOCAL_CTRL, &ctrl);
+ data = PHY_AUTO_NEG_802_3;
+ if (ctrl & PORT_AUTO_NEG_SYM_PAUSE)
+ data |= PHY_AUTO_NEG_SYM_PAUSE;
+ if (ctrl & PORT_AUTO_NEG_100BTX_FD)
+ data |= PHY_AUTO_NEG_100BTX_FD;
+ if (ctrl & PORT_AUTO_NEG_100BTX)
+ data |= PHY_AUTO_NEG_100BTX;
+ if (ctrl & PORT_AUTO_NEG_10BT_FD)
+ data |= PHY_AUTO_NEG_10BT_FD;
+ if (ctrl & PORT_AUTO_NEG_10BT)
+ data |= PHY_AUTO_NEG_10BT;
+ break;
+ case PHY_REG_REMOTE_CAPABILITY:
+ ksz_pread8(dev, p, P_REMOTE_STATUS, &link);
+ data = PHY_AUTO_NEG_802_3;
+ if (link & PORT_REMOTE_SYM_PAUSE)
+ data |= PHY_AUTO_NEG_SYM_PAUSE;
+ if (link & PORT_REMOTE_100BTX_FD)
+ data |= PHY_AUTO_NEG_100BTX_FD;
+ if (link & PORT_REMOTE_100BTX)
+ data |= PHY_AUTO_NEG_100BTX;
+ if (link & PORT_REMOTE_10BT_FD)
+ data |= PHY_AUTO_NEG_10BT_FD;
+ if (link & PORT_REMOTE_10BT)
+ data |= PHY_AUTO_NEG_10BT;
+ if (data & ~PHY_AUTO_NEG_802_3)
+ data |= PHY_REMOTE_ACKNOWLEDGE_NOT;
+ break;
+ default:
+ processed = false;
+ break;
+ }
+ if (processed)
+ *val = data;
+}
+
+static void ksz8795_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
+{
+ u8 p = phy;
+ u8 restart, speed, ctrl, data;
+
+ switch (reg) {
+ case PHY_REG_CTRL:
+
+ /* Do not support PHY reset function. */
+ if (val & PHY_RESET)
+ break;
+ ksz_pread8(dev, p, P_SPEED_STATUS, &speed);
+ data = speed;
+ if (val & PHY_HP_MDIX)
+ data |= PORT_HP_MDIX;
+ else
+ data &= ~PORT_HP_MDIX;
+ if (data != speed)
+ ksz_pwrite8(dev, p, P_SPEED_STATUS, data);
+ ksz_pread8(dev, p, P_FORCE_CTRL, &ctrl);
+ data = ctrl;
+ if (!(val & PHY_AUTO_NEG_ENABLE))
+ data |= PORT_AUTO_NEG_DISABLE;
+ else
+ data &= ~PORT_AUTO_NEG_DISABLE;
+
+ /* Fiber port does not support auto-negotiation. */
+ if (dev->ports[p].fiber)
+ data |= PORT_AUTO_NEG_DISABLE;
+ if (val & PHY_SPEED_100MBIT)
+ data |= PORT_FORCE_100_MBIT;
+ else
+ data &= ~PORT_FORCE_100_MBIT;
+ if (val & PHY_FULL_DUPLEX)
+ data |= PORT_FORCE_FULL_DUPLEX;
+ else
+ data &= ~PORT_FORCE_FULL_DUPLEX;
+ if (data != ctrl)
+ ksz_pwrite8(dev, p, P_FORCE_CTRL, data);
+ ksz_pread8(dev, p, P_NEG_RESTART_CTRL, &restart);
+ data = restart;
+ if (val & PHY_LED_DISABLE)
+ data |= PORT_LED_OFF;
+ else
+ data &= ~PORT_LED_OFF;
+ if (val & PHY_TRANSMIT_DISABLE)
+ data |= PORT_TX_DISABLE;
+ else
+ data &= ~PORT_TX_DISABLE;
+ if (val & PHY_AUTO_NEG_RESTART)
+ data |= PORT_AUTO_NEG_RESTART;
+ else
+ data &= ~(PORT_AUTO_NEG_RESTART);
+ if (val & PHY_POWER_DOWN)
+ data |= PORT_POWER_DOWN;
+ else
+ data &= ~PORT_POWER_DOWN;
+ if (val & PHY_AUTO_MDIX_DISABLE)
+ data |= PORT_AUTO_MDIX_DISABLE;
+ else
+ data &= ~PORT_AUTO_MDIX_DISABLE;
+ if (val & PHY_FORCE_MDIX)
+ data |= PORT_FORCE_MDIX;
+ else
+ data &= ~PORT_FORCE_MDIX;
+ if (val & PHY_LOOPBACK)
+ data |= PORT_PHY_LOOPBACK;
+ else
+ data &= ~PORT_PHY_LOOPBACK;
+ if (data != restart)
+ ksz_pwrite8(dev, p, P_NEG_RESTART_CTRL, data);
+ break;
+ case PHY_REG_AUTO_NEGOTIATION:
+ ksz_pread8(dev, p, P_LOCAL_CTRL, &ctrl);
+ data = ctrl;
+ data &= ~(PORT_AUTO_NEG_SYM_PAUSE |
+ PORT_AUTO_NEG_100BTX_FD |
+ PORT_AUTO_NEG_100BTX |
+ PORT_AUTO_NEG_10BT_FD |
+ PORT_AUTO_NEG_10BT);
+ if (val & PHY_AUTO_NEG_SYM_PAUSE)
+ data |= PORT_AUTO_NEG_SYM_PAUSE;
+ if (val & PHY_AUTO_NEG_100BTX_FD)
+ data |= PORT_AUTO_NEG_100BTX_FD;
+ if (val & PHY_AUTO_NEG_100BTX)
+ data |= PORT_AUTO_NEG_100BTX;
+ if (val & PHY_AUTO_NEG_10BT_FD)
+ data |= PORT_AUTO_NEG_10BT_FD;
+ if (val & PHY_AUTO_NEG_10BT)
+ data |= PORT_AUTO_NEG_10BT;
+ if (data != ctrl)
+ ksz_pwrite8(dev, p, P_LOCAL_CTRL, data);
+ break;
+ default:
+ break;
+ }
+}
+
+static enum dsa_tag_protocol ksz8795_get_tag_protocol(struct dsa_switch *ds,
+ int port,
+ enum dsa_tag_protocol mp)
+{
+ return DSA_TAG_PROTO_KSZ8795;
+}
+
+static void ksz8795_get_strings(struct dsa_switch *ds, int port,
+ u32 stringset, uint8_t *buf)
+{
+ int i;
+
+ for (i = 0; i < TOTAL_SWITCH_COUNTER_NUM; i++) {
+ memcpy(buf + i * ETH_GSTRING_LEN, mib_names[i].string,
+ ETH_GSTRING_LEN);
+ }
+}
+
+static void ksz8795_cfg_port_member(struct ksz_device *dev, int port,
+ u8 member)
+{
+ u8 data;
+
+ ksz_pread8(dev, port, P_MIRROR_CTRL, &data);
+ data &= ~PORT_VLAN_MEMBERSHIP;
+ data |= (member & dev->port_mask);
+ ksz_pwrite8(dev, port, P_MIRROR_CTRL, data);
+ dev->ports[port].member = member;
+}
+
+static void ksz8795_port_stp_state_set(struct dsa_switch *ds, int port,
+ u8 state)
+{
+ struct ksz_device *dev = ds->priv;
+ int forward = dev->member;
+ struct ksz_port *p;
+ int member = -1;
+ u8 data;
+
+ p = &dev->ports[port];
+
+ ksz_pread8(dev, port, P_STP_CTRL, &data);
+ data &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE | PORT_LEARN_DISABLE);
+
+ switch (state) {
+ case BR_STATE_DISABLED:
+ data |= PORT_LEARN_DISABLE;
+ if (port < SWITCH_PORT_NUM)
+ member = 0;
+ break;
+ case BR_STATE_LISTENING:
+ data |= (PORT_RX_ENABLE | PORT_LEARN_DISABLE);
+ if (port < SWITCH_PORT_NUM &&
+ p->stp_state == BR_STATE_DISABLED)
+ member = dev->host_mask | p->vid_member;
+ break;
+ case BR_STATE_LEARNING:
+ data |= PORT_RX_ENABLE;
+ break;
+ case BR_STATE_FORWARDING:
+ data |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
+
+ /* This function is also used internally. */
+ if (port == dev->cpu_port)
+ break;
+
+ /* Port is a member of a bridge. */
+ if (dev->br_member & BIT(port)) {
+ dev->member |= BIT(port);
+ member = dev->member;
+ } else {
+ member = dev->host_mask | p->vid_member;
+ }
+ break;
+ case BR_STATE_BLOCKING:
+ data |= PORT_LEARN_DISABLE;
+ if (port < SWITCH_PORT_NUM &&
+ p->stp_state == BR_STATE_DISABLED)
+ member = dev->host_mask | p->vid_member;
+ break;
+ default:
+ dev_err(ds->dev, "invalid STP state: %d\n", state);
+ return;
+ }
+
+ ksz_pwrite8(dev, port, P_STP_CTRL, data);
+ p->stp_state = state;
+ if (data & PORT_RX_ENABLE)
+ dev->rx_ports |= BIT(port);
+ else
+ dev->rx_ports &= ~BIT(port);
+ if (data & PORT_TX_ENABLE)
+ dev->tx_ports |= BIT(port);
+ else
+ dev->tx_ports &= ~BIT(port);
+
+ /* Port membership may share register with STP state. */
+ if (member >= 0 && member != p->member)
+ ksz8795_cfg_port_member(dev, port, (u8)member);
+
+ /* Check if forwarding needs to be updated. */
+ if (state != BR_STATE_FORWARDING) {
+ if (dev->br_member & BIT(port))
+ dev->member &= ~BIT(port);
+ }
+
+ /* When topology has changed the function ksz_update_port_member
+ * should be called to modify port forwarding behavior.
+ */
+ if (forward != dev->member)
+ ksz_update_port_member(dev, port);
+}
+
+static void ksz8795_flush_dyn_mac_table(struct ksz_device *dev, int port)
+{
+ u8 learn[TOTAL_PORT_NUM];
+ int first, index, cnt;
+ struct ksz_port *p;
+
+ if ((uint)port < TOTAL_PORT_NUM) {
+ first = port;
+ cnt = port + 1;
+ } else {
+ /* Flush all ports. */
+ first = 0;
+ cnt = dev->mib_port_cnt;
+ }
+ for (index = first; index < cnt; index++) {
+ p = &dev->ports[index];
+ if (!p->on)
+ continue;
+ ksz_pread8(dev, index, P_STP_CTRL, &learn[index]);
+ if (!(learn[index] & PORT_LEARN_DISABLE))
+ ksz_pwrite8(dev, index, P_STP_CTRL,
+ learn[index] | PORT_LEARN_DISABLE);
+ }
+ ksz_cfg(dev, S_FLUSH_TABLE_CTRL, SW_FLUSH_DYN_MAC_TABLE, true);
+ for (index = first; index < cnt; index++) {
+ p = &dev->ports[index];
+ if (!p->on)
+ continue;
+ if (!(learn[index] & PORT_LEARN_DISABLE))
+ ksz_pwrite8(dev, index, P_STP_CTRL, learn[index]);
+ }
+}
+
+static int ksz8795_port_vlan_filtering(struct dsa_switch *ds, int port,
+ bool flag)
+{
+ struct ksz_device *dev = ds->priv;
+
+ ksz_cfg(dev, S_MIRROR_CTRL, SW_VLAN_ENABLE, flag);
+
+ return 0;
+}
+
+static void ksz8795_port_vlan_add(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
+ struct ksz_device *dev = ds->priv;
+ u16 data, vid, new_pvid = 0;
+ u8 fid, member, valid;
+
+ ksz_port_cfg(dev, port, P_TAG_CTRL, PORT_REMOVE_TAG, untagged);
+
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) {
+ ksz8795_r_vlan_table(dev, vid, &data);
+ ksz8795_from_vlan(data, &fid, &member, &valid);
+
+ /* First time to setup the VLAN entry. */
+ if (!valid) {
+ /* Need to find a way to map VID to FID. */
+ fid = 1;
+ valid = 1;
+ }
+ member |= BIT(port);
+
+ ksz8795_to_vlan(fid, member, valid, &data);
+ ksz8795_w_vlan_table(dev, vid, data);
+
+ /* change PVID */
+ if (vlan->flags & BRIDGE_VLAN_INFO_PVID)
+ new_pvid = vid;
+ }
+
+ if (new_pvid) {
+ ksz_pread16(dev, port, REG_PORT_CTRL_VID, &vid);
+ vid &= 0xfff;
+ vid |= new_pvid;
+ ksz_pwrite16(dev, port, REG_PORT_CTRL_VID, vid);
+ }
+}
+
+static int ksz8795_port_vlan_del(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
+ struct ksz_device *dev = ds->priv;
+ u16 data, vid, pvid, new_pvid = 0;
+ u8 fid, member, valid;
+
+ ksz_pread16(dev, port, REG_PORT_CTRL_VID, &pvid);
+ pvid = pvid & 0xFFF;
+
+ ksz_port_cfg(dev, port, P_TAG_CTRL, PORT_REMOVE_TAG, untagged);
+
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) {
+ ksz8795_r_vlan_table(dev, vid, &data);
+ ksz8795_from_vlan(data, &fid, &member, &valid);
+
+ member &= ~BIT(port);
+
+ /* Invalidate the entry if no more member. */
+ if (!member) {
+ fid = 0;
+ valid = 0;
+ }
+
+ if (pvid == vid)
+ new_pvid = 1;
+
+ ksz8795_to_vlan(fid, member, valid, &data);
+ ksz8795_w_vlan_table(dev, vid, data);
+ }
+
+ if (new_pvid != pvid)
+ ksz_pwrite16(dev, port, REG_PORT_CTRL_VID, pvid);
+
+ return 0;
+}
+
+static int ksz8795_port_mirror_add(struct dsa_switch *ds, int port,
+ struct dsa_mall_mirror_tc_entry *mirror,
+ bool ingress)
+{
+ struct ksz_device *dev = ds->priv;
+
+ if (ingress) {
+ ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, true);
+ dev->mirror_rx |= BIT(port);
+ } else {
+ ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, true);
+ dev->mirror_tx |= BIT(port);
+ }
+
+ ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_SNIFFER, false);
+
+ /* configure mirror port */
+ if (dev->mirror_rx || dev->mirror_tx)
+ ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL,
+ PORT_MIRROR_SNIFFER, true);
+
+ return 0;
+}
+
+static void ksz8795_port_mirror_del(struct dsa_switch *ds, int port,
+ struct dsa_mall_mirror_tc_entry *mirror)
+{
+ struct ksz_device *dev = ds->priv;
+ u8 data;
+
+ if (mirror->ingress) {
+ ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, false);
+ dev->mirror_rx &= ~BIT(port);
+ } else {
+ ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, false);
+ dev->mirror_tx &= ~BIT(port);
+ }
+
+ ksz_pread8(dev, port, P_MIRROR_CTRL, &data);
+
+ if (!dev->mirror_rx && !dev->mirror_tx)
+ ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL,
+ PORT_MIRROR_SNIFFER, false);
+}
+
+static void ksz8795_port_setup(struct ksz_device *dev, int port, bool cpu_port)
+{
+ struct ksz_port *p = &dev->ports[port];
+ u8 data8, member;
+
+ /* enable broadcast storm limit */
+ ksz_port_cfg(dev, port, P_BCAST_STORM_CTRL, PORT_BROADCAST_STORM, true);
+
+ ksz8795_set_prio_queue(dev, port, 4);
+
+ /* disable DiffServ priority */
+ ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_DIFFSERV_ENABLE, false);
+
+ /* replace priority */
+ ksz_port_cfg(dev, port, P_802_1P_CTRL, PORT_802_1P_REMAPPING, false);
+
+ /* enable 802.1p priority */
+ ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_ENABLE, true);
+
+ if (cpu_port) {
+ /* Configure MII interface for proper network communication. */
+ ksz_read8(dev, REG_PORT_5_CTRL_6, &data8);
+ data8 &= ~PORT_INTERFACE_TYPE;
+ data8 &= ~PORT_GMII_1GPS_MODE;
+ switch (dev->interface) {
+ case PHY_INTERFACE_MODE_MII:
+ p->phydev.speed = SPEED_100;
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ data8 |= PORT_INTERFACE_RMII;
+ p->phydev.speed = SPEED_100;
+ break;
+ case PHY_INTERFACE_MODE_GMII:
+ data8 |= PORT_GMII_1GPS_MODE;
+ data8 |= PORT_INTERFACE_GMII;
+ p->phydev.speed = SPEED_1000;
+ break;
+ default:
+ data8 &= ~PORT_RGMII_ID_IN_ENABLE;
+ data8 &= ~PORT_RGMII_ID_OUT_ENABLE;
+ if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ dev->interface == PHY_INTERFACE_MODE_RGMII_RXID)
+ data8 |= PORT_RGMII_ID_IN_ENABLE;
+ if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ dev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
+ data8 |= PORT_RGMII_ID_OUT_ENABLE;
+ data8 |= PORT_GMII_1GPS_MODE;
+ data8 |= PORT_INTERFACE_RGMII;
+ p->phydev.speed = SPEED_1000;
+ break;
+ }
+ ksz_write8(dev, REG_PORT_5_CTRL_6, data8);
+ p->phydev.duplex = 1;
+
+ member = dev->port_mask;
+ dev->on_ports = dev->host_mask;
+ dev->live_ports = dev->host_mask;
+ } else {
+ member = dev->host_mask | p->vid_member;
+ dev->on_ports |= BIT(port);
+
+ /* Link was detected before port is enabled. */
+ if (p->phydev.link)
+ dev->live_ports |= BIT(port);
+ }
+ ksz8795_cfg_port_member(dev, port, member);
+}
+
+static void ksz8795_config_cpu_port(struct dsa_switch *ds)
+{
+ struct ksz_device *dev = ds->priv;
+ struct ksz_port *p;
+ u8 remote;
+ int i;
+
+ ds->num_ports = dev->port_cnt + 1;
+
+ /* Switch marks the maximum frame with extra byte as oversize. */
+ ksz_cfg(dev, REG_SW_CTRL_2, SW_LEGAL_PACKET_DISABLE, true);
+ ksz_cfg(dev, S_TAIL_TAG_CTRL, SW_TAIL_TAG_ENABLE, true);
+
+ p = &dev->ports[dev->cpu_port];
+ p->vid_member = dev->port_mask;
+ p->on = 1;
+
+ ksz8795_port_setup(dev, dev->cpu_port, true);
+ dev->member = dev->host_mask;
+
+ for (i = 0; i < SWITCH_PORT_NUM; i++) {
+ p = &dev->ports[i];
+
+ /* Initialize to non-zero so that ksz_cfg_port_member() will
+ * be called.
+ */
+ p->vid_member = BIT(i);
+ p->member = dev->port_mask;
+ ksz8795_port_stp_state_set(ds, i, BR_STATE_DISABLED);
+
+ /* Last port may be disabled. */
+ if (i == dev->port_cnt)
+ break;
+ p->on = 1;
+ p->phy = 1;
+ }
+ for (i = 0; i < dev->phy_port_cnt; i++) {
+ p = &dev->ports[i];
+ if (!p->on)
+ continue;
+ ksz_pread8(dev, i, P_REMOTE_STATUS, &remote);
+ if (remote & PORT_FIBER_MODE)
+ p->fiber = 1;
+ if (p->fiber)
+ ksz_port_cfg(dev, i, P_STP_CTRL, PORT_FORCE_FLOW_CTRL,
+ true);
+ else
+ ksz_port_cfg(dev, i, P_STP_CTRL, PORT_FORCE_FLOW_CTRL,
+ false);
+ }
+}
+
+static int ksz8795_setup(struct dsa_switch *ds)
+{
+ struct ksz_device *dev = ds->priv;
+ struct alu_struct alu;
+ int i, ret = 0;
+
+ dev->vlan_cache = devm_kcalloc(dev->dev, sizeof(struct vlan_table),
+ dev->num_vlans, GFP_KERNEL);
+ if (!dev->vlan_cache)
+ return -ENOMEM;
+
+ ret = ksz8795_reset_switch(dev);
+ if (ret) {
+ dev_err(ds->dev, "failed to reset switch\n");
+ return ret;
+ }
+
+ ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_FLOW_CTRL, true);
+
+ /* Enable automatic fast aging when link changed detected. */
+ ksz_cfg(dev, S_LINK_AGING_CTRL, SW_LINK_AUTO_AGING, true);
+
+ /* Enable aggressive back off algorithm in half duplex mode. */
+ regmap_update_bits(dev->regmap[0], REG_SW_CTRL_1,
+ SW_AGGR_BACKOFF, SW_AGGR_BACKOFF);
+
+ /*
+ * Make sure unicast VLAN boundary is set as default and
+ * enable no excessive collision drop.
+ */
+ regmap_update_bits(dev->regmap[0], REG_SW_CTRL_2,
+ UNICAST_VLAN_BOUNDARY | NO_EXC_COLLISION_DROP,
+ UNICAST_VLAN_BOUNDARY | NO_EXC_COLLISION_DROP);
+
+ ksz8795_config_cpu_port(ds);
+
+ ksz_cfg(dev, REG_SW_CTRL_2, MULTICAST_STORM_DISABLE, true);
+
+ ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_REPLACE_VID, false);
+
+ ksz_cfg(dev, S_MIRROR_CTRL, SW_MIRROR_RX_TX, false);
+
+ /* set broadcast storm protection 10% rate */
+ regmap_update_bits(dev->regmap[1], S_REPLACE_VID_CTRL,
+ BROADCAST_STORM_RATE,
+ (BROADCAST_STORM_VALUE *
+ BROADCAST_STORM_PROT_RATE) / 100);
+
+ for (i = 0; i < VLAN_TABLE_ENTRIES; i++)
+ ksz8795_r_vlan_entries(dev, i);
+
+ /* Setup STP address for STP operation. */
+ memset(&alu, 0, sizeof(alu));
+ ether_addr_copy(alu.mac, eth_stp_addr);
+ alu.is_static = true;
+ alu.is_override = true;
+ alu.port_forward = dev->host_mask;
+
+ ksz8795_w_sta_mac_table(dev, 0, &alu);
+
+ ksz_init_mib_timer(dev);
+
+ return 0;
+}
+
+static const struct dsa_switch_ops ksz8795_switch_ops = {
+ .get_tag_protocol = ksz8795_get_tag_protocol,
+ .setup = ksz8795_setup,
+ .phy_read = ksz_phy_read16,
+ .phy_write = ksz_phy_write16,
+ .adjust_link = ksz_adjust_link,
+ .port_enable = ksz_enable_port,
+ .port_disable = ksz_disable_port,
+ .get_strings = ksz8795_get_strings,
+ .get_ethtool_stats = ksz_get_ethtool_stats,
+ .get_sset_count = ksz_sset_count,
+ .port_bridge_join = ksz_port_bridge_join,
+ .port_bridge_leave = ksz_port_bridge_leave,
+ .port_stp_state_set = ksz8795_port_stp_state_set,
+ .port_fast_age = ksz_port_fast_age,
+ .port_vlan_filtering = ksz8795_port_vlan_filtering,
+ .port_vlan_prepare = ksz_port_vlan_prepare,
+ .port_vlan_add = ksz8795_port_vlan_add,
+ .port_vlan_del = ksz8795_port_vlan_del,
+ .port_fdb_dump = ksz_port_fdb_dump,
+ .port_mdb_prepare = ksz_port_mdb_prepare,
+ .port_mdb_add = ksz_port_mdb_add,
+ .port_mdb_del = ksz_port_mdb_del,
+ .port_mirror_add = ksz8795_port_mirror_add,
+ .port_mirror_del = ksz8795_port_mirror_del,
+};
+
+static u32 ksz8795_get_port_addr(int port, int offset)
+{
+ return PORT_CTRL_ADDR(port, offset);
+}
+
+static int ksz8795_switch_detect(struct ksz_device *dev)
+{
+ u8 id1, id2;
+ u16 id16;
+ int ret;
+
+ /* read chip id */
+ ret = ksz_read16(dev, REG_CHIP_ID0, &id16);
+ if (ret)
+ return ret;
+
+ id1 = id16 >> 8;
+ id2 = id16 & SW_CHIP_ID_M;
+ if (id1 != FAMILY_ID ||
+ (id2 != CHIP_ID_94 && id2 != CHIP_ID_95))
+ return -ENODEV;
+
+ dev->mib_port_cnt = TOTAL_PORT_NUM;
+ dev->phy_port_cnt = SWITCH_PORT_NUM;
+ dev->port_cnt = SWITCH_PORT_NUM;
+
+ if (id2 == CHIP_ID_95) {
+ u8 val;
+
+ id2 = 0x95;
+ ksz_read8(dev, REG_PORT_1_STATUS_0, &val);
+ if (val & PORT_FIBER_MODE)
+ id2 = 0x65;
+ } else if (id2 == CHIP_ID_94) {
+ dev->port_cnt--;
+ dev->last_port = dev->port_cnt;
+ id2 = 0x94;
+ }
+ id16 &= ~0xff;
+ id16 |= id2;
+ dev->chip_id = id16;
+
+ dev->cpu_port = dev->mib_port_cnt - 1;
+ dev->host_mask = BIT(dev->cpu_port);
+
+ return 0;
+}
+
+struct ksz_chip_data {
+ u16 chip_id;
+ const char *dev_name;
+ int num_vlans;
+ int num_alus;
+ int num_statics;
+ int cpu_ports;
+ int port_cnt;
+};
+
+static const struct ksz_chip_data ksz8795_switch_chips[] = {
+ {
+ .chip_id = 0x8795,
+ .dev_name = "KSZ8795",
+ .num_vlans = 4096,
+ .num_alus = 0,
+ .num_statics = 8,
+ .cpu_ports = 0x10, /* can be configured as cpu port */
+ .port_cnt = 4, /* total physical port count */
+ },
+ {
+ .chip_id = 0x8794,
+ .dev_name = "KSZ8794",
+ .num_vlans = 4096,
+ .num_alus = 0,
+ .num_statics = 8,
+ .cpu_ports = 0x10, /* can be configured as cpu port */
+ .port_cnt = 3, /* total physical port count */
+ },
+ {
+ .chip_id = 0x8765,
+ .dev_name = "KSZ8765",
+ .num_vlans = 4096,
+ .num_alus = 0,
+ .num_statics = 8,
+ .cpu_ports = 0x10, /* can be configured as cpu port */
+ .port_cnt = 4, /* total physical port count */
+ },
+};
+
+static int ksz8795_switch_init(struct ksz_device *dev)
+{
+ int i;
+
+ dev->ds->ops = &ksz8795_switch_ops;
+
+ for (i = 0; i < ARRAY_SIZE(ksz8795_switch_chips); i++) {
+ const struct ksz_chip_data *chip = &ksz8795_switch_chips[i];
+
+ if (dev->chip_id == chip->chip_id) {
+ dev->name = chip->dev_name;
+ dev->num_vlans = chip->num_vlans;
+ dev->num_alus = chip->num_alus;
+ dev->num_statics = chip->num_statics;
+ dev->port_cnt = chip->port_cnt;
+ dev->cpu_ports = chip->cpu_ports;
+
+ break;
+ }
+ }
+
+ /* no switch found */
+ if (!dev->cpu_ports)
+ return -ENODEV;
+
+ dev->port_mask = BIT(dev->port_cnt) - 1;
+ dev->port_mask |= dev->host_mask;
+
+ dev->reg_mib_cnt = SWITCH_COUNTER_NUM;
+ dev->mib_cnt = TOTAL_SWITCH_COUNTER_NUM;
+
+ i = dev->mib_port_cnt;
+ dev->ports = devm_kzalloc(dev->dev, sizeof(struct ksz_port) * i,
+ GFP_KERNEL);
+ if (!dev->ports)
+ return -ENOMEM;
+ for (i = 0; i < dev->mib_port_cnt; i++) {
+ mutex_init(&dev->ports[i].mib.cnt_mutex);
+ dev->ports[i].mib.counters =
+ devm_kzalloc(dev->dev,
+ sizeof(u64) *
+ (TOTAL_SWITCH_COUNTER_NUM + 1),
+ GFP_KERNEL);
+ if (!dev->ports[i].mib.counters)
+ return -ENOMEM;
+ }
+
+ /* set the real number of ports */
+ dev->ds->num_ports = dev->port_cnt;
+
+ return 0;
+}
+
+static void ksz8795_switch_exit(struct ksz_device *dev)
+{
+ ksz8795_reset_switch(dev);
+}
+
+static const struct ksz_dev_ops ksz8795_dev_ops = {
+ .get_port_addr = ksz8795_get_port_addr,
+ .cfg_port_member = ksz8795_cfg_port_member,
+ .flush_dyn_mac_table = ksz8795_flush_dyn_mac_table,
+ .port_setup = ksz8795_port_setup,
+ .r_phy = ksz8795_r_phy,
+ .w_phy = ksz8795_w_phy,
+ .r_dyn_mac_table = ksz8795_r_dyn_mac_table,
+ .r_sta_mac_table = ksz8795_r_sta_mac_table,
+ .w_sta_mac_table = ksz8795_w_sta_mac_table,
+ .r_mib_cnt = ksz8795_r_mib_cnt,
+ .r_mib_pkt = ksz8795_r_mib_pkt,
+ .freeze_mib = ksz8795_freeze_mib,
+ .port_init_cnt = ksz8795_port_init_cnt,
+ .shutdown = ksz8795_reset_switch,
+ .detect = ksz8795_switch_detect,
+ .init = ksz8795_switch_init,
+ .exit = ksz8795_switch_exit,
+};
+
+int ksz8795_switch_register(struct ksz_device *dev)
+{
+ return ksz_switch_register(dev, &ksz8795_dev_ops);
+}
+EXPORT_SYMBOL(ksz8795_switch_register);
+
+MODULE_AUTHOR("Tristram Ha <Tristram.Ha@microchip.com>");
+MODULE_DESCRIPTION("Microchip KSZ8795 Series Switch DSA Driver");
+MODULE_LICENSE("GPL");
diff --git a/marvell/linux/drivers/net/dsa/microchip/ksz8795_reg.h b/marvell/linux/drivers/net/dsa/microchip/ksz8795_reg.h
new file mode 100644
index 0000000..3a50462
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/ksz8795_reg.h
@@ -0,0 +1,1004 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Microchip KSZ8795 register definitions
+ *
+ * Copyright (c) 2017 Microchip Technology Inc.
+ * Tristram Ha <Tristram.Ha@microchip.com>
+ */
+
+#ifndef __KSZ8795_REG_H
+#define __KSZ8795_REG_H
+
+#define KS_PORT_M 0x1F
+
+#define KS_PRIO_M 0x3
+#define KS_PRIO_S 2
+
+#define REG_CHIP_ID0 0x00
+
+#define FAMILY_ID 0x87
+
+#define REG_CHIP_ID1 0x01
+
+#define SW_CHIP_ID_M 0xF0
+#define SW_CHIP_ID_S 4
+#define SW_REVISION_M 0x0E
+#define SW_REVISION_S 1
+#define SW_START 0x01
+
+#define CHIP_ID_94 0x60
+#define CHIP_ID_95 0x90
+
+#define REG_SW_CTRL_0 0x02
+
+#define SW_NEW_BACKOFF BIT(7)
+#define SW_GLOBAL_RESET BIT(6)
+#define SW_FLUSH_DYN_MAC_TABLE BIT(5)
+#define SW_FLUSH_STA_MAC_TABLE BIT(4)
+#define SW_LINK_AUTO_AGING BIT(0)
+
+#define REG_SW_CTRL_1 0x03
+
+#define SW_HUGE_PACKET BIT(6)
+#define SW_TX_FLOW_CTRL_DISABLE BIT(5)
+#define SW_RX_FLOW_CTRL_DISABLE BIT(4)
+#define SW_CHECK_LENGTH BIT(3)
+#define SW_AGING_ENABLE BIT(2)
+#define SW_FAST_AGING BIT(1)
+#define SW_AGGR_BACKOFF BIT(0)
+
+#define REG_SW_CTRL_2 0x04
+
+#define UNICAST_VLAN_BOUNDARY BIT(7)
+#define MULTICAST_STORM_DISABLE BIT(6)
+#define SW_BACK_PRESSURE BIT(5)
+#define FAIR_FLOW_CTRL BIT(4)
+#define NO_EXC_COLLISION_DROP BIT(3)
+#define SW_LEGAL_PACKET_DISABLE BIT(1)
+
+#define REG_SW_CTRL_3 0x05
+ #define WEIGHTED_FAIR_QUEUE_ENABLE BIT(3)
+
+#define SW_VLAN_ENABLE BIT(7)
+#define SW_IGMP_SNOOP BIT(6)
+#define SW_MIRROR_RX_TX BIT(0)
+
+#define REG_SW_CTRL_4 0x06
+
+#define SW_HALF_DUPLEX_FLOW_CTRL BIT(7)
+#define SW_HALF_DUPLEX BIT(6)
+#define SW_FLOW_CTRL BIT(5)
+#define SW_10_MBIT BIT(4)
+#define SW_REPLACE_VID BIT(3)
+#define BROADCAST_STORM_RATE_HI 0x07
+
+#define REG_SW_CTRL_5 0x07
+
+#define BROADCAST_STORM_RATE_LO 0xFF
+#define BROADCAST_STORM_RATE 0x07FF
+
+#define REG_SW_CTRL_6 0x08
+
+#define SW_MIB_COUNTER_FLUSH BIT(7)
+#define SW_MIB_COUNTER_FREEZE BIT(6)
+#define SW_MIB_COUNTER_CTRL_ENABLE KS_PORT_M
+
+#define REG_SW_CTRL_9 0x0B
+
+#define SPI_CLK_125_MHZ 0x80
+#define SPI_CLK_62_5_MHZ 0x40
+#define SPI_CLK_31_25_MHZ 0x00
+
+#define SW_LED_MODE_M 0x3
+#define SW_LED_MODE_S 4
+#define SW_LED_LINK_ACT_SPEED 0
+#define SW_LED_LINK_ACT 1
+#define SW_LED_LINK_ACT_DUPLEX 2
+#define SW_LED_LINK_DUPLEX 3
+
+#define REG_SW_CTRL_10 0x0C
+
+#define SW_TAIL_TAG_ENABLE BIT(1)
+#define SW_PASS_PAUSE BIT(0)
+
+#define REG_SW_CTRL_11 0x0D
+
+#define REG_POWER_MANAGEMENT_1 0x0E
+
+#define SW_PLL_POWER_DOWN BIT(5)
+#define SW_POWER_MANAGEMENT_MODE_M 0x3
+#define SW_POWER_MANAGEMENT_MODE_S 3
+#define SW_POWER_NORMAL 0
+#define SW_ENERGY_DETECTION 1
+#define SW_SOFTWARE_POWER_DOWN 2
+
+#define REG_POWER_MANAGEMENT_2 0x0F
+
+#define REG_PORT_1_CTRL_0 0x10
+#define REG_PORT_2_CTRL_0 0x20
+#define REG_PORT_3_CTRL_0 0x30
+#define REG_PORT_4_CTRL_0 0x40
+#define REG_PORT_5_CTRL_0 0x50
+
+#define PORT_BROADCAST_STORM BIT(7)
+#define PORT_DIFFSERV_ENABLE BIT(6)
+#define PORT_802_1P_ENABLE BIT(5)
+#define PORT_BASED_PRIO_S 3
+#define PORT_BASED_PRIO_M KS_PRIO_M
+#define PORT_BASED_PRIO_0 0
+#define PORT_BASED_PRIO_1 1
+#define PORT_BASED_PRIO_2 2
+#define PORT_BASED_PRIO_3 3
+#define PORT_INSERT_TAG BIT(2)
+#define PORT_REMOVE_TAG BIT(1)
+#define PORT_QUEUE_SPLIT_L BIT(0)
+
+#define REG_PORT_1_CTRL_1 0x11
+#define REG_PORT_2_CTRL_1 0x21
+#define REG_PORT_3_CTRL_1 0x31
+#define REG_PORT_4_CTRL_1 0x41
+#define REG_PORT_5_CTRL_1 0x51
+
+#define PORT_MIRROR_SNIFFER BIT(7)
+#define PORT_MIRROR_RX BIT(6)
+#define PORT_MIRROR_TX BIT(5)
+#define PORT_VLAN_MEMBERSHIP KS_PORT_M
+
+#define REG_PORT_1_CTRL_2 0x12
+#define REG_PORT_2_CTRL_2 0x22
+#define REG_PORT_3_CTRL_2 0x32
+#define REG_PORT_4_CTRL_2 0x42
+#define REG_PORT_5_CTRL_2 0x52
+
+#define PORT_802_1P_REMAPPING BIT(7)
+#define PORT_INGRESS_FILTER BIT(6)
+#define PORT_DISCARD_NON_VID BIT(5)
+#define PORT_FORCE_FLOW_CTRL BIT(4)
+#define PORT_BACK_PRESSURE BIT(3)
+#define PORT_TX_ENABLE BIT(2)
+#define PORT_RX_ENABLE BIT(1)
+#define PORT_LEARN_DISABLE BIT(0)
+
+#define REG_PORT_1_CTRL_3 0x13
+#define REG_PORT_2_CTRL_3 0x23
+#define REG_PORT_3_CTRL_3 0x33
+#define REG_PORT_4_CTRL_3 0x43
+#define REG_PORT_5_CTRL_3 0x53
+#define REG_PORT_1_CTRL_4 0x14
+#define REG_PORT_2_CTRL_4 0x24
+#define REG_PORT_3_CTRL_4 0x34
+#define REG_PORT_4_CTRL_4 0x44
+#define REG_PORT_5_CTRL_4 0x54
+
+#define PORT_DEFAULT_VID 0x0001
+
+#define REG_PORT_1_CTRL_5 0x15
+#define REG_PORT_2_CTRL_5 0x25
+#define REG_PORT_3_CTRL_5 0x35
+#define REG_PORT_4_CTRL_5 0x45
+#define REG_PORT_5_CTRL_5 0x55
+
+#define PORT_ACL_ENABLE BIT(2)
+#define PORT_AUTHEN_MODE 0x3
+#define PORT_AUTHEN_PASS 0
+#define PORT_AUTHEN_BLOCK 1
+#define PORT_AUTHEN_TRAP 2
+
+#define REG_PORT_5_CTRL_6 0x56
+
+#define PORT_MII_INTERNAL_CLOCK BIT(7)
+#define PORT_GMII_1GPS_MODE BIT(6)
+#define PORT_RGMII_ID_IN_ENABLE BIT(4)
+#define PORT_RGMII_ID_OUT_ENABLE BIT(3)
+#define PORT_GMII_MAC_MODE BIT(2)
+#define PORT_INTERFACE_TYPE 0x3
+#define PORT_INTERFACE_MII 0
+#define PORT_INTERFACE_RMII 1
+#define PORT_INTERFACE_GMII 2
+#define PORT_INTERFACE_RGMII 3
+
+#define REG_PORT_1_CTRL_7 0x17
+#define REG_PORT_2_CTRL_7 0x27
+#define REG_PORT_3_CTRL_7 0x37
+#define REG_PORT_4_CTRL_7 0x47
+
+#define PORT_AUTO_NEG_ASYM_PAUSE BIT(5)
+#define PORT_AUTO_NEG_SYM_PAUSE BIT(4)
+#define PORT_AUTO_NEG_100BTX_FD BIT(3)
+#define PORT_AUTO_NEG_100BTX BIT(2)
+#define PORT_AUTO_NEG_10BT_FD BIT(1)
+#define PORT_AUTO_NEG_10BT BIT(0)
+
+#define REG_PORT_1_STATUS_0 0x18
+#define REG_PORT_2_STATUS_0 0x28
+#define REG_PORT_3_STATUS_0 0x38
+#define REG_PORT_4_STATUS_0 0x48
+
+/* For KSZ8765. */
+#define PORT_FIBER_MODE BIT(7)
+
+#define PORT_REMOTE_ASYM_PAUSE BIT(5)
+#define PORT_REMOTE_SYM_PAUSE BIT(4)
+#define PORT_REMOTE_100BTX_FD BIT(3)
+#define PORT_REMOTE_100BTX BIT(2)
+#define PORT_REMOTE_10BT_FD BIT(1)
+#define PORT_REMOTE_10BT BIT(0)
+
+#define REG_PORT_1_STATUS_1 0x19
+#define REG_PORT_2_STATUS_1 0x29
+#define REG_PORT_3_STATUS_1 0x39
+#define REG_PORT_4_STATUS_1 0x49
+
+#define PORT_HP_MDIX BIT(7)
+#define PORT_REVERSED_POLARITY BIT(5)
+#define PORT_TX_FLOW_CTRL BIT(4)
+#define PORT_RX_FLOW_CTRL BIT(3)
+#define PORT_STAT_SPEED_100MBIT BIT(2)
+#define PORT_STAT_FULL_DUPLEX BIT(1)
+
+#define PORT_REMOTE_FAULT BIT(0)
+
+#define REG_PORT_1_LINK_MD_CTRL 0x1A
+#define REG_PORT_2_LINK_MD_CTRL 0x2A
+#define REG_PORT_3_LINK_MD_CTRL 0x3A
+#define REG_PORT_4_LINK_MD_CTRL 0x4A
+
+#define PORT_CABLE_10M_SHORT BIT(7)
+#define PORT_CABLE_DIAG_RESULT_M 0x3
+#define PORT_CABLE_DIAG_RESULT_S 5
+#define PORT_CABLE_STAT_NORMAL 0
+#define PORT_CABLE_STAT_OPEN 1
+#define PORT_CABLE_STAT_SHORT 2
+#define PORT_CABLE_STAT_FAILED 3
+#define PORT_START_CABLE_DIAG BIT(4)
+#define PORT_FORCE_LINK BIT(3)
+#define PORT_POWER_SAVING BIT(2)
+#define PORT_PHY_REMOTE_LOOPBACK BIT(1)
+#define PORT_CABLE_FAULT_COUNTER_H 0x01
+
+#define REG_PORT_1_LINK_MD_RESULT 0x1B
+#define REG_PORT_2_LINK_MD_RESULT 0x2B
+#define REG_PORT_3_LINK_MD_RESULT 0x3B
+#define REG_PORT_4_LINK_MD_RESULT 0x4B
+
+#define PORT_CABLE_FAULT_COUNTER_L 0xFF
+#define PORT_CABLE_FAULT_COUNTER 0x1FF
+
+#define REG_PORT_1_CTRL_9 0x1C
+#define REG_PORT_2_CTRL_9 0x2C
+#define REG_PORT_3_CTRL_9 0x3C
+#define REG_PORT_4_CTRL_9 0x4C
+
+#define PORT_AUTO_NEG_DISABLE BIT(7)
+#define PORT_FORCE_100_MBIT BIT(6)
+#define PORT_FORCE_FULL_DUPLEX BIT(5)
+
+#define REG_PORT_1_CTRL_10 0x1D
+#define REG_PORT_2_CTRL_10 0x2D
+#define REG_PORT_3_CTRL_10 0x3D
+#define REG_PORT_4_CTRL_10 0x4D
+
+#define PORT_LED_OFF BIT(7)
+#define PORT_TX_DISABLE BIT(6)
+#define PORT_AUTO_NEG_RESTART BIT(5)
+#define PORT_POWER_DOWN BIT(3)
+#define PORT_AUTO_MDIX_DISABLE BIT(2)
+#define PORT_FORCE_MDIX BIT(1)
+#define PORT_MAC_LOOPBACK BIT(0)
+
+#define REG_PORT_1_STATUS_2 0x1E
+#define REG_PORT_2_STATUS_2 0x2E
+#define REG_PORT_3_STATUS_2 0x3E
+#define REG_PORT_4_STATUS_2 0x4E
+
+#define PORT_MDIX_STATUS BIT(7)
+#define PORT_AUTO_NEG_COMPLETE BIT(6)
+#define PORT_STAT_LINK_GOOD BIT(5)
+
+#define REG_PORT_1_STATUS_3 0x1F
+#define REG_PORT_2_STATUS_3 0x2F
+#define REG_PORT_3_STATUS_3 0x3F
+#define REG_PORT_4_STATUS_3 0x4F
+
+#define PORT_PHY_LOOPBACK BIT(7)
+#define PORT_PHY_ISOLATE BIT(5)
+#define PORT_PHY_SOFT_RESET BIT(4)
+#define PORT_PHY_FORCE_LINK BIT(3)
+#define PORT_PHY_MODE_M 0x7
+#define PHY_MODE_IN_AUTO_NEG 1
+#define PHY_MODE_10BT_HALF 2
+#define PHY_MODE_100BT_HALF 3
+#define PHY_MODE_10BT_FULL 5
+#define PHY_MODE_100BT_FULL 6
+#define PHY_MODE_ISOLDATE 7
+
+#define REG_PORT_CTRL_0 0x00
+#define REG_PORT_CTRL_1 0x01
+#define REG_PORT_CTRL_2 0x02
+#define REG_PORT_CTRL_VID 0x03
+
+#define REG_PORT_CTRL_5 0x05
+
+#define REG_PORT_CTRL_7 0x07
+#define REG_PORT_STATUS_0 0x08
+#define REG_PORT_STATUS_1 0x09
+#define REG_PORT_LINK_MD_CTRL 0x0A
+#define REG_PORT_LINK_MD_RESULT 0x0B
+#define REG_PORT_CTRL_9 0x0C
+#define REG_PORT_CTRL_10 0x0D
+#define REG_PORT_STATUS_2 0x0E
+#define REG_PORT_STATUS_3 0x0F
+
+#define REG_PORT_CTRL_12 0xA0
+#define REG_PORT_CTRL_13 0xA1
+#define REG_PORT_RATE_CTRL_3 0xA2
+#define REG_PORT_RATE_CTRL_2 0xA3
+#define REG_PORT_RATE_CTRL_1 0xA4
+#define REG_PORT_RATE_CTRL_0 0xA5
+#define REG_PORT_RATE_LIMIT 0xA6
+#define REG_PORT_IN_RATE_0 0xA7
+#define REG_PORT_IN_RATE_1 0xA8
+#define REG_PORT_IN_RATE_2 0xA9
+#define REG_PORT_IN_RATE_3 0xAA
+#define REG_PORT_OUT_RATE_0 0xAB
+#define REG_PORT_OUT_RATE_1 0xAC
+#define REG_PORT_OUT_RATE_2 0xAD
+#define REG_PORT_OUT_RATE_3 0xAE
+
+#define PORT_CTRL_ADDR(port, addr) \
+ ((addr) + REG_PORT_1_CTRL_0 + (port) * \
+ (REG_PORT_2_CTRL_0 - REG_PORT_1_CTRL_0))
+
+#define REG_SW_MAC_ADDR_0 0x68
+#define REG_SW_MAC_ADDR_1 0x69
+#define REG_SW_MAC_ADDR_2 0x6A
+#define REG_SW_MAC_ADDR_3 0x6B
+#define REG_SW_MAC_ADDR_4 0x6C
+#define REG_SW_MAC_ADDR_5 0x6D
+
+#define REG_IND_CTRL_0 0x6E
+
+#define TABLE_EXT_SELECT_S 5
+#define TABLE_EEE_V 1
+#define TABLE_ACL_V 2
+#define TABLE_PME_V 4
+#define TABLE_LINK_MD_V 5
+#define TABLE_EEE (TABLE_EEE_V << TABLE_EXT_SELECT_S)
+#define TABLE_ACL (TABLE_ACL_V << TABLE_EXT_SELECT_S)
+#define TABLE_PME (TABLE_PME_V << TABLE_EXT_SELECT_S)
+#define TABLE_LINK_MD (TABLE_LINK_MD << TABLE_EXT_SELECT_S)
+#define TABLE_READ BIT(4)
+#define TABLE_SELECT_S 2
+#define TABLE_STATIC_MAC_V 0
+#define TABLE_VLAN_V 1
+#define TABLE_DYNAMIC_MAC_V 2
+#define TABLE_MIB_V 3
+#define TABLE_STATIC_MAC (TABLE_STATIC_MAC_V << TABLE_SELECT_S)
+#define TABLE_VLAN (TABLE_VLAN_V << TABLE_SELECT_S)
+#define TABLE_DYNAMIC_MAC (TABLE_DYNAMIC_MAC_V << TABLE_SELECT_S)
+#define TABLE_MIB (TABLE_MIB_V << TABLE_SELECT_S)
+
+#define REG_IND_CTRL_1 0x6F
+
+#define TABLE_ENTRY_MASK 0x03FF
+#define TABLE_EXT_ENTRY_MASK 0x0FFF
+
+#define REG_IND_DATA_8 0x70
+#define REG_IND_DATA_7 0x71
+#define REG_IND_DATA_6 0x72
+#define REG_IND_DATA_5 0x73
+#define REG_IND_DATA_4 0x74
+#define REG_IND_DATA_3 0x75
+#define REG_IND_DATA_2 0x76
+#define REG_IND_DATA_1 0x77
+#define REG_IND_DATA_0 0x78
+
+#define REG_IND_DATA_PME_EEE_ACL 0xA0
+
+#define REG_IND_DATA_CHECK REG_IND_DATA_6
+#define REG_IND_MIB_CHECK REG_IND_DATA_4
+#define REG_IND_DATA_HI REG_IND_DATA_7
+#define REG_IND_DATA_LO REG_IND_DATA_3
+
+#define REG_INT_STATUS 0x7C
+#define REG_INT_ENABLE 0x7D
+
+#define INT_PME BIT(4)
+
+#define REG_ACL_INT_STATUS 0x7E
+#define REG_ACL_INT_ENABLE 0x7F
+
+#define INT_PORT_5 BIT(4)
+#define INT_PORT_4 BIT(3)
+#define INT_PORT_3 BIT(2)
+#define INT_PORT_2 BIT(1)
+#define INT_PORT_1 BIT(0)
+
+#define INT_PORT_ALL \
+ (INT_PORT_5 | INT_PORT_4 | INT_PORT_3 | INT_PORT_2 | INT_PORT_1)
+
+#define REG_SW_CTRL_12 0x80
+#define REG_SW_CTRL_13 0x81
+
+#define SWITCH_802_1P_MASK 3
+#define SWITCH_802_1P_BASE 3
+#define SWITCH_802_1P_SHIFT 2
+
+#define SW_802_1P_MAP_M KS_PRIO_M
+#define SW_802_1P_MAP_S KS_PRIO_S
+
+#define REG_SWITCH_CTRL_14 0x82
+
+#define SW_PRIO_MAPPING_M KS_PRIO_M
+#define SW_PRIO_MAPPING_S 6
+#define SW_PRIO_MAP_3_HI 0
+#define SW_PRIO_MAP_2_HI 2
+#define SW_PRIO_MAP_0_LO 3
+
+#define REG_SW_CTRL_15 0x83
+#define REG_SW_CTRL_16 0x84
+#define REG_SW_CTRL_17 0x85
+#define REG_SW_CTRL_18 0x86
+
+#define SW_SELF_ADDR_FILTER_ENABLE BIT(6)
+
+#define REG_SW_UNK_UCAST_CTRL 0x83
+#define REG_SW_UNK_MCAST_CTRL 0x84
+#define REG_SW_UNK_VID_CTRL 0x85
+#define REG_SW_UNK_IP_MCAST_CTRL 0x86
+
+#define SW_UNK_FWD_ENABLE BIT(5)
+#define SW_UNK_FWD_MAP KS_PORT_M
+
+#define REG_SW_CTRL_19 0x87
+
+#define SW_IN_RATE_LIMIT_PERIOD_M 0x3
+#define SW_IN_RATE_LIMIT_PERIOD_S 4
+#define SW_IN_RATE_LIMIT_16_MS 0
+#define SW_IN_RATE_LIMIT_64_MS 1
+#define SW_IN_RATE_LIMIT_256_MS 2
+#define SW_OUT_RATE_LIMIT_QUEUE_BASED BIT(3)
+#define SW_INS_TAG_ENABLE BIT(2)
+
+#define REG_TOS_PRIO_CTRL_0 0x90
+#define REG_TOS_PRIO_CTRL_1 0x91
+#define REG_TOS_PRIO_CTRL_2 0x92
+#define REG_TOS_PRIO_CTRL_3 0x93
+#define REG_TOS_PRIO_CTRL_4 0x94
+#define REG_TOS_PRIO_CTRL_5 0x95
+#define REG_TOS_PRIO_CTRL_6 0x96
+#define REG_TOS_PRIO_CTRL_7 0x97
+#define REG_TOS_PRIO_CTRL_8 0x98
+#define REG_TOS_PRIO_CTRL_9 0x99
+#define REG_TOS_PRIO_CTRL_10 0x9A
+#define REG_TOS_PRIO_CTRL_11 0x9B
+#define REG_TOS_PRIO_CTRL_12 0x9C
+#define REG_TOS_PRIO_CTRL_13 0x9D
+#define REG_TOS_PRIO_CTRL_14 0x9E
+#define REG_TOS_PRIO_CTRL_15 0x9F
+
+#define TOS_PRIO_M KS_PRIO_M
+#define TOS_PRIO_S KS_PRIO_S
+
+#define REG_SW_CTRL_20 0xA3
+
+#define SW_GMII_DRIVE_STRENGTH_S 4
+#define SW_DRIVE_STRENGTH_M 0x7
+#define SW_DRIVE_STRENGTH_2MA 0
+#define SW_DRIVE_STRENGTH_4MA 1
+#define SW_DRIVE_STRENGTH_8MA 2
+#define SW_DRIVE_STRENGTH_12MA 3
+#define SW_DRIVE_STRENGTH_16MA 4
+#define SW_DRIVE_STRENGTH_20MA 5
+#define SW_DRIVE_STRENGTH_24MA 6
+#define SW_DRIVE_STRENGTH_28MA 7
+#define SW_MII_DRIVE_STRENGTH_S 0
+
+#define REG_SW_CTRL_21 0xA4
+
+#define SW_IPV6_MLD_OPTION BIT(3)
+#define SW_IPV6_MLD_SNOOP BIT(2)
+
+#define REG_PORT_1_CTRL_12 0xB0
+#define REG_PORT_2_CTRL_12 0xC0
+#define REG_PORT_3_CTRL_12 0xD0
+#define REG_PORT_4_CTRL_12 0xE0
+#define REG_PORT_5_CTRL_12 0xF0
+
+#define PORT_PASS_ALL BIT(6)
+#define PORT_INS_TAG_FOR_PORT_5_S 3
+#define PORT_INS_TAG_FOR_PORT_5 BIT(3)
+#define PORT_INS_TAG_FOR_PORT_4 BIT(2)
+#define PORT_INS_TAG_FOR_PORT_3 BIT(1)
+#define PORT_INS_TAG_FOR_PORT_2 BIT(0)
+
+#define REG_PORT_1_CTRL_13 0xB1
+#define REG_PORT_2_CTRL_13 0xC1
+#define REG_PORT_3_CTRL_13 0xD1
+#define REG_PORT_4_CTRL_13 0xE1
+#define REG_PORT_5_CTRL_13 0xF1
+
+#define PORT_QUEUE_SPLIT_H BIT(1)
+#define PORT_QUEUE_SPLIT_1 0
+#define PORT_QUEUE_SPLIT_2 1
+#define PORT_QUEUE_SPLIT_4 2
+#define PORT_DROP_TAG BIT(0)
+
+#define REG_PORT_1_CTRL_14 0xB2
+#define REG_PORT_2_CTRL_14 0xC2
+#define REG_PORT_3_CTRL_14 0xD2
+#define REG_PORT_4_CTRL_14 0xE2
+#define REG_PORT_5_CTRL_14 0xF2
+#define REG_PORT_1_CTRL_15 0xB3
+#define REG_PORT_2_CTRL_15 0xC3
+#define REG_PORT_3_CTRL_15 0xD3
+#define REG_PORT_4_CTRL_15 0xE3
+#define REG_PORT_5_CTRL_15 0xF3
+#define REG_PORT_1_CTRL_16 0xB4
+#define REG_PORT_2_CTRL_16 0xC4
+#define REG_PORT_3_CTRL_16 0xD4
+#define REG_PORT_4_CTRL_16 0xE4
+#define REG_PORT_5_CTRL_16 0xF4
+#define REG_PORT_1_CTRL_17 0xB5
+#define REG_PORT_2_CTRL_17 0xC5
+#define REG_PORT_3_CTRL_17 0xD5
+#define REG_PORT_4_CTRL_17 0xE5
+#define REG_PORT_5_CTRL_17 0xF5
+
+#define REG_PORT_1_RATE_CTRL_3 0xB2
+#define REG_PORT_1_RATE_CTRL_2 0xB3
+#define REG_PORT_1_RATE_CTRL_1 0xB4
+#define REG_PORT_1_RATE_CTRL_0 0xB5
+#define REG_PORT_2_RATE_CTRL_3 0xC2
+#define REG_PORT_2_RATE_CTRL_2 0xC3
+#define REG_PORT_2_RATE_CTRL_1 0xC4
+#define REG_PORT_2_RATE_CTRL_0 0xC5
+#define REG_PORT_3_RATE_CTRL_3 0xD2
+#define REG_PORT_3_RATE_CTRL_2 0xD3
+#define REG_PORT_3_RATE_CTRL_1 0xD4
+#define REG_PORT_3_RATE_CTRL_0 0xD5
+#define REG_PORT_4_RATE_CTRL_3 0xE2
+#define REG_PORT_4_RATE_CTRL_2 0xE3
+#define REG_PORT_4_RATE_CTRL_1 0xE4
+#define REG_PORT_4_RATE_CTRL_0 0xE5
+#define REG_PORT_5_RATE_CTRL_3 0xF2
+#define REG_PORT_5_RATE_CTRL_2 0xF3
+#define REG_PORT_5_RATE_CTRL_1 0xF4
+#define REG_PORT_5_RATE_CTRL_0 0xF5
+
+#define RATE_CTRL_ENABLE BIT(7)
+#define RATE_RATIO_M (BIT(7) - 1)
+
+#define PORT_OUT_RATE_ENABLE BIT(7)
+
+#define REG_PORT_1_RATE_LIMIT 0xB6
+#define REG_PORT_2_RATE_LIMIT 0xC6
+#define REG_PORT_3_RATE_LIMIT 0xD6
+#define REG_PORT_4_RATE_LIMIT 0xE6
+#define REG_PORT_5_RATE_LIMIT 0xF6
+
+#define PORT_IN_PORT_BASED_S 6
+#define PORT_RATE_PACKET_BASED_S 5
+#define PORT_IN_FLOW_CTRL_S 4
+#define PORT_IN_LIMIT_MODE_M 0x3
+#define PORT_IN_LIMIT_MODE_S 2
+#define PORT_COUNT_IFG_S 1
+#define PORT_COUNT_PREAMBLE_S 0
+#define PORT_IN_PORT_BASED BIT(PORT_IN_PORT_BASED_S)
+#define PORT_RATE_PACKET_BASED BIT(PORT_RATE_PACKET_BASED_S)
+#define PORT_IN_FLOW_CTRL BIT(PORT_IN_FLOW_CTRL_S)
+#define PORT_IN_ALL 0
+#define PORT_IN_UNICAST 1
+#define PORT_IN_MULTICAST 2
+#define PORT_IN_BROADCAST 3
+#define PORT_COUNT_IFG BIT(PORT_COUNT_IFG_S)
+#define PORT_COUNT_PREAMBLE BIT(PORT_COUNT_PREAMBLE_S)
+
+#define REG_PORT_1_IN_RATE_0 0xB7
+#define REG_PORT_2_IN_RATE_0 0xC7
+#define REG_PORT_3_IN_RATE_0 0xD7
+#define REG_PORT_4_IN_RATE_0 0xE7
+#define REG_PORT_5_IN_RATE_0 0xF7
+#define REG_PORT_1_IN_RATE_1 0xB8
+#define REG_PORT_2_IN_RATE_1 0xC8
+#define REG_PORT_3_IN_RATE_1 0xD8
+#define REG_PORT_4_IN_RATE_1 0xE8
+#define REG_PORT_5_IN_RATE_1 0xF8
+#define REG_PORT_1_IN_RATE_2 0xB9
+#define REG_PORT_2_IN_RATE_2 0xC9
+#define REG_PORT_3_IN_RATE_2 0xD9
+#define REG_PORT_4_IN_RATE_2 0xE9
+#define REG_PORT_5_IN_RATE_2 0xF9
+#define REG_PORT_1_IN_RATE_3 0xBA
+#define REG_PORT_2_IN_RATE_3 0xCA
+#define REG_PORT_3_IN_RATE_3 0xDA
+#define REG_PORT_4_IN_RATE_3 0xEA
+#define REG_PORT_5_IN_RATE_3 0xFA
+
+#define PORT_IN_RATE_ENABLE BIT(7)
+#define PORT_RATE_LIMIT_M (BIT(7) - 1)
+
+#define REG_PORT_1_OUT_RATE_0 0xBB
+#define REG_PORT_2_OUT_RATE_0 0xCB
+#define REG_PORT_3_OUT_RATE_0 0xDB
+#define REG_PORT_4_OUT_RATE_0 0xEB
+#define REG_PORT_5_OUT_RATE_0 0xFB
+#define REG_PORT_1_OUT_RATE_1 0xBC
+#define REG_PORT_2_OUT_RATE_1 0xCC
+#define REG_PORT_3_OUT_RATE_1 0xDC
+#define REG_PORT_4_OUT_RATE_1 0xEC
+#define REG_PORT_5_OUT_RATE_1 0xFC
+#define REG_PORT_1_OUT_RATE_2 0xBD
+#define REG_PORT_2_OUT_RATE_2 0xCD
+#define REG_PORT_3_OUT_RATE_2 0xDD
+#define REG_PORT_4_OUT_RATE_2 0xED
+#define REG_PORT_5_OUT_RATE_2 0xFD
+#define REG_PORT_1_OUT_RATE_3 0xBE
+#define REG_PORT_2_OUT_RATE_3 0xCE
+#define REG_PORT_3_OUT_RATE_3 0xDE
+#define REG_PORT_4_OUT_RATE_3 0xEE
+#define REG_PORT_5_OUT_RATE_3 0xFE
+
+/* PME */
+
+#define SW_PME_OUTPUT_ENABLE BIT(1)
+#define SW_PME_ACTIVE_HIGH BIT(0)
+
+#define PORT_MAGIC_PACKET_DETECT BIT(2)
+#define PORT_LINK_UP_DETECT BIT(1)
+#define PORT_ENERGY_DETECT BIT(0)
+
+/* ACL */
+
+#define ACL_FIRST_RULE_M 0xF
+
+#define ACL_MODE_M 0x3
+#define ACL_MODE_S 4
+#define ACL_MODE_DISABLE 0
+#define ACL_MODE_LAYER_2 1
+#define ACL_MODE_LAYER_3 2
+#define ACL_MODE_LAYER_4 3
+#define ACL_ENABLE_M 0x3
+#define ACL_ENABLE_S 2
+#define ACL_ENABLE_2_COUNT 0
+#define ACL_ENABLE_2_TYPE 1
+#define ACL_ENABLE_2_MAC 2
+#define ACL_ENABLE_2_BOTH 3
+#define ACL_ENABLE_3_IP 1
+#define ACL_ENABLE_3_SRC_DST_COMP 2
+#define ACL_ENABLE_4_PROTOCOL 0
+#define ACL_ENABLE_4_TCP_PORT_COMP 1
+#define ACL_ENABLE_4_UDP_PORT_COMP 2
+#define ACL_ENABLE_4_TCP_SEQN_COMP 3
+#define ACL_SRC BIT(1)
+#define ACL_EQUAL BIT(0)
+
+#define ACL_MAX_PORT 0xFFFF
+
+#define ACL_MIN_PORT 0xFFFF
+#define ACL_IP_ADDR 0xFFFFFFFF
+#define ACL_TCP_SEQNUM 0xFFFFFFFF
+
+#define ACL_RESERVED 0xF8
+#define ACL_PORT_MODE_M 0x3
+#define ACL_PORT_MODE_S 1
+#define ACL_PORT_MODE_DISABLE 0
+#define ACL_PORT_MODE_EITHER 1
+#define ACL_PORT_MODE_IN_RANGE 2
+#define ACL_PORT_MODE_OUT_OF_RANGE 3
+
+#define ACL_TCP_FLAG_ENABLE BIT(0)
+
+#define ACL_TCP_FLAG_M 0xFF
+
+#define ACL_TCP_FLAG 0xFF
+#define ACL_ETH_TYPE 0xFFFF
+#define ACL_IP_M 0xFFFFFFFF
+
+#define ACL_PRIO_MODE_M 0x3
+#define ACL_PRIO_MODE_S 6
+#define ACL_PRIO_MODE_DISABLE 0
+#define ACL_PRIO_MODE_HIGHER 1
+#define ACL_PRIO_MODE_LOWER 2
+#define ACL_PRIO_MODE_REPLACE 3
+#define ACL_PRIO_M 0x7
+#define ACL_PRIO_S 3
+#define ACL_VLAN_PRIO_REPLACE BIT(2)
+#define ACL_VLAN_PRIO_M 0x7
+#define ACL_VLAN_PRIO_HI_M 0x3
+
+#define ACL_VLAN_PRIO_LO_M 0x8
+#define ACL_VLAN_PRIO_S 7
+#define ACL_MAP_MODE_M 0x3
+#define ACL_MAP_MODE_S 5
+#define ACL_MAP_MODE_DISABLE 0
+#define ACL_MAP_MODE_OR 1
+#define ACL_MAP_MODE_AND 2
+#define ACL_MAP_MODE_REPLACE 3
+#define ACL_MAP_PORT_M 0x1F
+
+#define ACL_CNT_M (BIT(11) - 1)
+#define ACL_CNT_S 5
+#define ACL_MSEC_UNIT BIT(4)
+#define ACL_INTR_MODE BIT(3)
+
+#define REG_PORT_ACL_BYTE_EN_MSB 0x10
+
+#define ACL_BYTE_EN_MSB_M 0x3F
+
+#define REG_PORT_ACL_BYTE_EN_LSB 0x11
+
+#define ACL_ACTION_START 0xA
+#define ACL_ACTION_LEN 2
+#define ACL_INTR_CNT_START 0xB
+#define ACL_RULESET_START 0xC
+#define ACL_RULESET_LEN 2
+#define ACL_TABLE_LEN 14
+
+#define ACL_ACTION_ENABLE 0x000C
+#define ACL_MATCH_ENABLE 0x1FF0
+#define ACL_RULESET_ENABLE 0x2003
+#define ACL_BYTE_ENABLE ((ACL_BYTE_EN_MSB_M << 8) | 0xFF)
+#define ACL_MODE_ENABLE (0x10 << 8)
+
+#define REG_PORT_ACL_CTRL_0 0x12
+
+#define PORT_ACL_WRITE_DONE BIT(6)
+#define PORT_ACL_READ_DONE BIT(5)
+#define PORT_ACL_WRITE BIT(4)
+#define PORT_ACL_INDEX_M 0xF
+
+#define REG_PORT_ACL_CTRL_1 0x13
+
+#define PORT_ACL_FORCE_DLR_MISS BIT(0)
+
+#ifndef PHY_REG_CTRL
+#define PHY_REG_CTRL 0
+
+#define PHY_RESET BIT(15)
+#define PHY_LOOPBACK BIT(14)
+#define PHY_SPEED_100MBIT BIT(13)
+#define PHY_AUTO_NEG_ENABLE BIT(12)
+#define PHY_POWER_DOWN BIT(11)
+#define PHY_MII_DISABLE BIT(10)
+#define PHY_AUTO_NEG_RESTART BIT(9)
+#define PHY_FULL_DUPLEX BIT(8)
+#define PHY_COLLISION_TEST_NOT BIT(7)
+#define PHY_HP_MDIX BIT(5)
+#define PHY_FORCE_MDIX BIT(4)
+#define PHY_AUTO_MDIX_DISABLE BIT(3)
+#define PHY_REMOTE_FAULT_DISABLE BIT(2)
+#define PHY_TRANSMIT_DISABLE BIT(1)
+#define PHY_LED_DISABLE BIT(0)
+
+#define PHY_REG_STATUS 1
+
+#define PHY_100BT4_CAPABLE BIT(15)
+#define PHY_100BTX_FD_CAPABLE BIT(14)
+#define PHY_100BTX_CAPABLE BIT(13)
+#define PHY_10BT_FD_CAPABLE BIT(12)
+#define PHY_10BT_CAPABLE BIT(11)
+#define PHY_MII_SUPPRESS_CAPABLE_NOT BIT(6)
+#define PHY_AUTO_NEG_ACKNOWLEDGE BIT(5)
+#define PHY_REMOTE_FAULT BIT(4)
+#define PHY_AUTO_NEG_CAPABLE BIT(3)
+#define PHY_LINK_STATUS BIT(2)
+#define PHY_JABBER_DETECT_NOT BIT(1)
+#define PHY_EXTENDED_CAPABILITY BIT(0)
+
+#define PHY_REG_ID_1 2
+#define PHY_REG_ID_2 3
+
+#define PHY_REG_AUTO_NEGOTIATION 4
+
+#define PHY_AUTO_NEG_NEXT_PAGE_NOT BIT(15)
+#define PHY_AUTO_NEG_REMOTE_FAULT_NOT BIT(13)
+#define PHY_AUTO_NEG_SYM_PAUSE BIT(10)
+#define PHY_AUTO_NEG_100BT4 BIT(9)
+#define PHY_AUTO_NEG_100BTX_FD BIT(8)
+#define PHY_AUTO_NEG_100BTX BIT(7)
+#define PHY_AUTO_NEG_10BT_FD BIT(6)
+#define PHY_AUTO_NEG_10BT BIT(5)
+#define PHY_AUTO_NEG_SELECTOR 0x001F
+#define PHY_AUTO_NEG_802_3 0x0001
+
+#define PHY_REG_REMOTE_CAPABILITY 5
+
+#define PHY_REMOTE_NEXT_PAGE_NOT BIT(15)
+#define PHY_REMOTE_ACKNOWLEDGE_NOT BIT(14)
+#define PHY_REMOTE_REMOTE_FAULT_NOT BIT(13)
+#define PHY_REMOTE_SYM_PAUSE BIT(10)
+#define PHY_REMOTE_100BTX_FD BIT(8)
+#define PHY_REMOTE_100BTX BIT(7)
+#define PHY_REMOTE_10BT_FD BIT(6)
+#define PHY_REMOTE_10BT BIT(5)
+#endif
+
+#define KSZ8795_ID_HI 0x0022
+#define KSZ8795_ID_LO 0x1550
+
+#define KSZ8795_SW_ID 0x8795
+
+#define PHY_REG_LINK_MD 0x1D
+
+#define PHY_START_CABLE_DIAG BIT(15)
+#define PHY_CABLE_DIAG_RESULT 0x6000
+#define PHY_CABLE_STAT_NORMAL 0x0000
+#define PHY_CABLE_STAT_OPEN 0x2000
+#define PHY_CABLE_STAT_SHORT 0x4000
+#define PHY_CABLE_STAT_FAILED 0x6000
+#define PHY_CABLE_10M_SHORT BIT(12)
+#define PHY_CABLE_FAULT_COUNTER 0x01FF
+
+#define PHY_REG_PHY_CTRL 0x1F
+
+#define PHY_MODE_M 0x7
+#define PHY_MODE_S 8
+#define PHY_STAT_REVERSED_POLARITY BIT(5)
+#define PHY_STAT_MDIX BIT(4)
+#define PHY_FORCE_LINK BIT(3)
+#define PHY_POWER_SAVING_ENABLE BIT(2)
+#define PHY_REMOTE_LOOPBACK BIT(1)
+
+/* Chip resource */
+
+#define PRIO_QUEUES 4
+
+#define KS_PRIO_IN_REG 4
+
+#define TOTAL_PORT_NUM 5
+
+/* Host port can only be last of them. */
+#define SWITCH_PORT_NUM (TOTAL_PORT_NUM - 1)
+
+#define KSZ8795_COUNTER_NUM 0x20
+#define TOTAL_KSZ8795_COUNTER_NUM (KSZ8795_COUNTER_NUM + 4)
+
+#define SWITCH_COUNTER_NUM KSZ8795_COUNTER_NUM
+#define TOTAL_SWITCH_COUNTER_NUM TOTAL_KSZ8795_COUNTER_NUM
+
+/* Common names used by other drivers */
+
+#define P_BCAST_STORM_CTRL REG_PORT_CTRL_0
+#define P_PRIO_CTRL REG_PORT_CTRL_0
+#define P_TAG_CTRL REG_PORT_CTRL_0
+#define P_MIRROR_CTRL REG_PORT_CTRL_1
+#define P_802_1P_CTRL REG_PORT_CTRL_2
+#define P_STP_CTRL REG_PORT_CTRL_2
+#define P_LOCAL_CTRL REG_PORT_CTRL_7
+#define P_REMOTE_STATUS REG_PORT_STATUS_0
+#define P_FORCE_CTRL REG_PORT_CTRL_9
+#define P_NEG_RESTART_CTRL REG_PORT_CTRL_10
+#define P_SPEED_STATUS REG_PORT_STATUS_1
+#define P_LINK_STATUS REG_PORT_STATUS_2
+#define P_PASS_ALL_CTRL REG_PORT_CTRL_12
+#define P_INS_SRC_PVID_CTRL REG_PORT_CTRL_12
+#define P_DROP_TAG_CTRL REG_PORT_CTRL_13
+#define P_RATE_LIMIT_CTRL REG_PORT_RATE_LIMIT
+
+#define S_UNKNOWN_DA_CTRL REG_SWITCH_CTRL_12
+#define S_FORWARD_INVALID_VID_CTRL REG_FORWARD_INVALID_VID
+
+#define S_FLUSH_TABLE_CTRL REG_SW_CTRL_0
+#define S_LINK_AGING_CTRL REG_SW_CTRL_0
+#define S_HUGE_PACKET_CTRL REG_SW_CTRL_1
+#define S_MIRROR_CTRL REG_SW_CTRL_3
+#define S_REPLACE_VID_CTRL REG_SW_CTRL_4
+#define S_PASS_PAUSE_CTRL REG_SW_CTRL_10
+#define S_TAIL_TAG_CTRL REG_SW_CTRL_10
+#define S_802_1P_PRIO_CTRL REG_SW_CTRL_12
+#define S_TOS_PRIO_CTRL REG_TOS_PRIO_CTRL_0
+#define S_IPV6_MLD_CTRL REG_SW_CTRL_21
+
+#define IND_ACC_TABLE(table) ((table) << 8)
+
+/* Driver set switch broadcast storm protection at 10% rate. */
+#define BROADCAST_STORM_PROT_RATE 10
+
+/* 148,800 frames * 67 ms / 100 */
+#define BROADCAST_STORM_VALUE 9969
+
+/**
+ * STATIC_MAC_TABLE_ADDR 00-0000FFFF-FFFFFFFF
+ * STATIC_MAC_TABLE_FWD_PORTS 00-001F0000-00000000
+ * STATIC_MAC_TABLE_VALID 00-00200000-00000000
+ * STATIC_MAC_TABLE_OVERRIDE 00-00400000-00000000
+ * STATIC_MAC_TABLE_USE_FID 00-00800000-00000000
+ * STATIC_MAC_TABLE_FID 00-7F000000-00000000
+ */
+
+#define STATIC_MAC_TABLE_ADDR 0x0000FFFF
+#define STATIC_MAC_TABLE_FWD_PORTS 0x001F0000
+#define STATIC_MAC_TABLE_VALID 0x00200000
+#define STATIC_MAC_TABLE_OVERRIDE 0x00400000
+#define STATIC_MAC_TABLE_USE_FID 0x00800000
+#define STATIC_MAC_TABLE_FID 0x7F000000
+
+#define STATIC_MAC_FWD_PORTS_S 16
+#define STATIC_MAC_FID_S 24
+
+/**
+ * VLAN_TABLE_FID 00-007F007F-007F007F
+ * VLAN_TABLE_MEMBERSHIP 00-0F800F80-0F800F80
+ * VLAN_TABLE_VALID 00-10001000-10001000
+ */
+
+#define VLAN_TABLE_FID 0x007F
+#define VLAN_TABLE_MEMBERSHIP 0x0F80
+#define VLAN_TABLE_VALID 0x1000
+
+#define VLAN_TABLE_MEMBERSHIP_S 7
+#define VLAN_TABLE_S 16
+
+/**
+ * DYNAMIC_MAC_TABLE_ADDR 00-0000FFFF-FFFFFFFF
+ * DYNAMIC_MAC_TABLE_FID 00-007F0000-00000000
+ * DYNAMIC_MAC_TABLE_NOT_READY 00-00800000-00000000
+ * DYNAMIC_MAC_TABLE_SRC_PORT 00-07000000-00000000
+ * DYNAMIC_MAC_TABLE_TIMESTAMP 00-18000000-00000000
+ * DYNAMIC_MAC_TABLE_ENTRIES 7F-E0000000-00000000
+ * DYNAMIC_MAC_TABLE_MAC_EMPTY 80-00000000-00000000
+ */
+
+#define DYNAMIC_MAC_TABLE_ADDR 0x0000FFFF
+#define DYNAMIC_MAC_TABLE_FID 0x007F0000
+#define DYNAMIC_MAC_TABLE_SRC_PORT 0x07000000
+#define DYNAMIC_MAC_TABLE_TIMESTAMP 0x18000000
+#define DYNAMIC_MAC_TABLE_ENTRIES 0xE0000000
+
+#define DYNAMIC_MAC_TABLE_NOT_READY 0x80
+
+#define DYNAMIC_MAC_TABLE_ENTRIES_H 0x7F
+#define DYNAMIC_MAC_TABLE_MAC_EMPTY 0x80
+
+#define DYNAMIC_MAC_FID_S 16
+#define DYNAMIC_MAC_SRC_PORT_S 24
+#define DYNAMIC_MAC_TIMESTAMP_S 27
+#define DYNAMIC_MAC_ENTRIES_S 29
+#define DYNAMIC_MAC_ENTRIES_H_S 3
+
+/**
+ * MIB_COUNTER_VALUE 00-00000000-3FFFFFFF
+ * MIB_TOTAL_BYTES 00-0000000F-FFFFFFFF
+ * MIB_PACKET_DROPPED 00-00000000-0000FFFF
+ * MIB_COUNTER_VALID 00-00000020-00000000
+ * MIB_COUNTER_OVERFLOW 00-00000040-00000000
+ */
+
+#define MIB_COUNTER_OVERFLOW BIT(6)
+#define MIB_COUNTER_VALID BIT(5)
+
+#define MIB_COUNTER_VALUE 0x3FFFFFFF
+
+#define KS_MIB_TOTAL_RX_0 0x100
+#define KS_MIB_TOTAL_TX_0 0x101
+#define KS_MIB_PACKET_DROPPED_RX_0 0x102
+#define KS_MIB_PACKET_DROPPED_TX_0 0x103
+#define KS_MIB_TOTAL_RX_1 0x104
+#define KS_MIB_TOTAL_TX_1 0x105
+#define KS_MIB_PACKET_DROPPED_TX_1 0x106
+#define KS_MIB_PACKET_DROPPED_RX_1 0x107
+#define KS_MIB_TOTAL_RX_2 0x108
+#define KS_MIB_TOTAL_TX_2 0x109
+#define KS_MIB_PACKET_DROPPED_TX_2 0x10A
+#define KS_MIB_PACKET_DROPPED_RX_2 0x10B
+#define KS_MIB_TOTAL_RX_3 0x10C
+#define KS_MIB_TOTAL_TX_3 0x10D
+#define KS_MIB_PACKET_DROPPED_TX_3 0x10E
+#define KS_MIB_PACKET_DROPPED_RX_3 0x10F
+#define KS_MIB_TOTAL_RX_4 0x110
+#define KS_MIB_TOTAL_TX_4 0x111
+#define KS_MIB_PACKET_DROPPED_TX_4 0x112
+#define KS_MIB_PACKET_DROPPED_RX_4 0x113
+
+#define MIB_PACKET_DROPPED 0x0000FFFF
+
+#define MIB_TOTAL_BYTES_H 0x0000000F
+
+#define TAIL_TAG_OVERRIDE BIT(6)
+#define TAIL_TAG_LOOKUP BIT(7)
+
+#define VLAN_TABLE_ENTRIES (4096 / 4)
+#define FID_ENTRIES 128
+
+#endif
diff --git a/marvell/linux/drivers/net/dsa/microchip/ksz8795_spi.c b/marvell/linux/drivers/net/dsa/microchip/ksz8795_spi.c
new file mode 100644
index 0000000..5639c5c
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/ksz8795_spi.c
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Microchip KSZ8795 series register access through SPI
+ *
+ * Copyright (C) 2017 Microchip Technology Inc.
+ * Tristram Ha <Tristram.Ha@microchip.com>
+ */
+
+#include <asm/unaligned.h>
+
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+#include "ksz_common.h"
+
+#define SPI_ADDR_SHIFT 12
+#define SPI_ADDR_ALIGN 3
+#define SPI_TURNAROUND_SHIFT 1
+
+KSZ_REGMAP_TABLE(ksz8795, 16, SPI_ADDR_SHIFT,
+ SPI_TURNAROUND_SHIFT, SPI_ADDR_ALIGN);
+
+static int ksz8795_spi_probe(struct spi_device *spi)
+{
+ struct regmap_config rc;
+ struct ksz_device *dev;
+ int i, ret;
+
+ dev = ksz_switch_alloc(&spi->dev, spi);
+ if (!dev)
+ return -ENOMEM;
+
+ for (i = 0; i < ARRAY_SIZE(ksz8795_regmap_config); i++) {
+ rc = ksz8795_regmap_config[i];
+ rc.lock_arg = &dev->regmap_mutex;
+ dev->regmap[i] = devm_regmap_init_spi(spi, &rc);
+ if (IS_ERR(dev->regmap[i])) {
+ ret = PTR_ERR(dev->regmap[i]);
+ dev_err(&spi->dev,
+ "Failed to initialize regmap%i: %d\n",
+ ksz8795_regmap_config[i].val_bits, ret);
+ return ret;
+ }
+ }
+
+ if (spi->dev.platform_data)
+ dev->pdata = spi->dev.platform_data;
+
+ ret = ksz8795_switch_register(dev);
+
+ /* Main DSA driver may not be started yet. */
+ if (ret)
+ return ret;
+
+ spi_set_drvdata(spi, dev);
+
+ return 0;
+}
+
+static int ksz8795_spi_remove(struct spi_device *spi)
+{
+ struct ksz_device *dev = spi_get_drvdata(spi);
+
+ if (dev)
+ ksz_switch_remove(dev);
+
+ return 0;
+}
+
+static void ksz8795_spi_shutdown(struct spi_device *spi)
+{
+ struct ksz_device *dev = spi_get_drvdata(spi);
+
+ if (dev && dev->dev_ops->shutdown)
+ dev->dev_ops->shutdown(dev);
+}
+
+static const struct of_device_id ksz8795_dt_ids[] = {
+ { .compatible = "microchip,ksz8765" },
+ { .compatible = "microchip,ksz8794" },
+ { .compatible = "microchip,ksz8795" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ksz8795_dt_ids);
+
+static const struct spi_device_id ksz8795_spi_ids[] = {
+ { "ksz8765" },
+ { "ksz8794" },
+ { "ksz8795" },
+ { "ksz8863" },
+ { "ksz8873" },
+ { },
+};
+MODULE_DEVICE_TABLE(spi, ksz8795_spi_ids);
+
+static struct spi_driver ksz8795_spi_driver = {
+ .driver = {
+ .name = "ksz8795-switch",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(ksz8795_dt_ids),
+ },
+ .id_table = ksz8795_spi_ids,
+ .probe = ksz8795_spi_probe,
+ .remove = ksz8795_spi_remove,
+ .shutdown = ksz8795_spi_shutdown,
+};
+
+module_spi_driver(ksz8795_spi_driver);
+
+MODULE_AUTHOR("Tristram Ha <Tristram.Ha@microchip.com>");
+MODULE_DESCRIPTION("Microchip KSZ8795 Series Switch SPI Driver");
+MODULE_LICENSE("GPL");
diff --git a/marvell/linux/drivers/net/dsa/microchip/ksz9477.c b/marvell/linux/drivers/net/dsa/microchip/ksz9477.c
new file mode 100644
index 0000000..3475f82
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/ksz9477.c
@@ -0,0 +1,1632 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Microchip KSZ9477 switch driver main logic
+ *
+ * Copyright (C) 2017-2019 Microchip Technology Inc.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/iopoll.h>
+#include <linux/platform_data/microchip-ksz.h>
+#include <linux/phy.h>
+#include <linux/if_bridge.h>
+#include <net/dsa.h>
+#include <net/switchdev.h>
+
+#include "ksz9477_reg.h"
+#include "ksz_common.h"
+
+/* Used with variable features to indicate capabilities. */
+#define GBIT_SUPPORT BIT(0)
+#define NEW_XMII BIT(1)
+#define IS_9893 BIT(2)
+
+static const struct {
+ int index;
+ char string[ETH_GSTRING_LEN];
+} ksz9477_mib_names[TOTAL_SWITCH_COUNTER_NUM] = {
+ { 0x00, "rx_hi" },
+ { 0x01, "rx_undersize" },
+ { 0x02, "rx_fragments" },
+ { 0x03, "rx_oversize" },
+ { 0x04, "rx_jabbers" },
+ { 0x05, "rx_symbol_err" },
+ { 0x06, "rx_crc_err" },
+ { 0x07, "rx_align_err" },
+ { 0x08, "rx_mac_ctrl" },
+ { 0x09, "rx_pause" },
+ { 0x0A, "rx_bcast" },
+ { 0x0B, "rx_mcast" },
+ { 0x0C, "rx_ucast" },
+ { 0x0D, "rx_64_or_less" },
+ { 0x0E, "rx_65_127" },
+ { 0x0F, "rx_128_255" },
+ { 0x10, "rx_256_511" },
+ { 0x11, "rx_512_1023" },
+ { 0x12, "rx_1024_1522" },
+ { 0x13, "rx_1523_2000" },
+ { 0x14, "rx_2001" },
+ { 0x15, "tx_hi" },
+ { 0x16, "tx_late_col" },
+ { 0x17, "tx_pause" },
+ { 0x18, "tx_bcast" },
+ { 0x19, "tx_mcast" },
+ { 0x1A, "tx_ucast" },
+ { 0x1B, "tx_deferred" },
+ { 0x1C, "tx_total_col" },
+ { 0x1D, "tx_exc_col" },
+ { 0x1E, "tx_single_col" },
+ { 0x1F, "tx_mult_col" },
+ { 0x80, "rx_total" },
+ { 0x81, "tx_total" },
+ { 0x82, "rx_discards" },
+ { 0x83, "tx_discards" },
+};
+
+static void ksz_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set)
+{
+ regmap_update_bits(dev->regmap[0], addr, bits, set ? bits : 0);
+}
+
+static void ksz_port_cfg(struct ksz_device *dev, int port, int offset, u8 bits,
+ bool set)
+{
+ regmap_update_bits(dev->regmap[0], PORT_CTRL_ADDR(port, offset),
+ bits, set ? bits : 0);
+}
+
+static void ksz9477_cfg32(struct ksz_device *dev, u32 addr, u32 bits, bool set)
+{
+ regmap_update_bits(dev->regmap[2], addr, bits, set ? bits : 0);
+}
+
+static void ksz9477_port_cfg32(struct ksz_device *dev, int port, int offset,
+ u32 bits, bool set)
+{
+ regmap_update_bits(dev->regmap[2], PORT_CTRL_ADDR(port, offset),
+ bits, set ? bits : 0);
+}
+
+static int ksz9477_wait_vlan_ctrl_ready(struct ksz_device *dev)
+{
+ unsigned int val;
+
+ return regmap_read_poll_timeout(dev->regmap[0], REG_SW_VLAN_CTRL,
+ val, !(val & VLAN_START), 10, 1000);
+}
+
+static int ksz9477_get_vlan_table(struct ksz_device *dev, u16 vid,
+ u32 *vlan_table)
+{
+ int ret;
+
+ mutex_lock(&dev->vlan_mutex);
+
+ ksz_write16(dev, REG_SW_VLAN_ENTRY_INDEX__2, vid & VLAN_INDEX_M);
+ ksz_write8(dev, REG_SW_VLAN_CTRL, VLAN_READ | VLAN_START);
+
+ /* wait to be cleared */
+ ret = ksz9477_wait_vlan_ctrl_ready(dev);
+ if (ret) {
+ dev_dbg(dev->dev, "Failed to read vlan table\n");
+ goto exit;
+ }
+
+ ksz_read32(dev, REG_SW_VLAN_ENTRY__4, &vlan_table[0]);
+ ksz_read32(dev, REG_SW_VLAN_ENTRY_UNTAG__4, &vlan_table[1]);
+ ksz_read32(dev, REG_SW_VLAN_ENTRY_PORTS__4, &vlan_table[2]);
+
+ ksz_write8(dev, REG_SW_VLAN_CTRL, 0);
+
+exit:
+ mutex_unlock(&dev->vlan_mutex);
+
+ return ret;
+}
+
+static int ksz9477_set_vlan_table(struct ksz_device *dev, u16 vid,
+ u32 *vlan_table)
+{
+ int ret;
+
+ mutex_lock(&dev->vlan_mutex);
+
+ ksz_write32(dev, REG_SW_VLAN_ENTRY__4, vlan_table[0]);
+ ksz_write32(dev, REG_SW_VLAN_ENTRY_UNTAG__4, vlan_table[1]);
+ ksz_write32(dev, REG_SW_VLAN_ENTRY_PORTS__4, vlan_table[2]);
+
+ ksz_write16(dev, REG_SW_VLAN_ENTRY_INDEX__2, vid & VLAN_INDEX_M);
+ ksz_write8(dev, REG_SW_VLAN_CTRL, VLAN_START | VLAN_WRITE);
+
+ /* wait to be cleared */
+ ret = ksz9477_wait_vlan_ctrl_ready(dev);
+ if (ret) {
+ dev_dbg(dev->dev, "Failed to write vlan table\n");
+ goto exit;
+ }
+
+ ksz_write8(dev, REG_SW_VLAN_CTRL, 0);
+
+ /* update vlan cache table */
+ dev->vlan_cache[vid].table[0] = vlan_table[0];
+ dev->vlan_cache[vid].table[1] = vlan_table[1];
+ dev->vlan_cache[vid].table[2] = vlan_table[2];
+
+exit:
+ mutex_unlock(&dev->vlan_mutex);
+
+ return ret;
+}
+
+static void ksz9477_read_table(struct ksz_device *dev, u32 *table)
+{
+ ksz_read32(dev, REG_SW_ALU_VAL_A, &table[0]);
+ ksz_read32(dev, REG_SW_ALU_VAL_B, &table[1]);
+ ksz_read32(dev, REG_SW_ALU_VAL_C, &table[2]);
+ ksz_read32(dev, REG_SW_ALU_VAL_D, &table[3]);
+}
+
+static void ksz9477_write_table(struct ksz_device *dev, u32 *table)
+{
+ ksz_write32(dev, REG_SW_ALU_VAL_A, table[0]);
+ ksz_write32(dev, REG_SW_ALU_VAL_B, table[1]);
+ ksz_write32(dev, REG_SW_ALU_VAL_C, table[2]);
+ ksz_write32(dev, REG_SW_ALU_VAL_D, table[3]);
+}
+
+static int ksz9477_wait_alu_ready(struct ksz_device *dev)
+{
+ unsigned int val;
+
+ return regmap_read_poll_timeout(dev->regmap[2], REG_SW_ALU_CTRL__4,
+ val, !(val & ALU_START), 10, 1000);
+}
+
+static int ksz9477_wait_alu_sta_ready(struct ksz_device *dev)
+{
+ unsigned int val;
+
+ return regmap_read_poll_timeout(dev->regmap[2],
+ REG_SW_ALU_STAT_CTRL__4,
+ val, !(val & ALU_STAT_START),
+ 10, 1000);
+}
+
+static int ksz9477_reset_switch(struct ksz_device *dev)
+{
+ u8 data8;
+ u32 data32;
+
+ /* reset switch */
+ ksz_cfg(dev, REG_SW_OPERATION, SW_RESET, true);
+
+ /* turn off SPI DO Edge select */
+ regmap_update_bits(dev->regmap[0], REG_SW_GLOBAL_SERIAL_CTRL_0,
+ SPI_AUTO_EDGE_DETECTION, 0);
+
+ /* default configuration */
+ ksz_write8(dev, REG_SW_LUE_CTRL_1,
+ SW_AGING_ENABLE | SW_LINK_AUTO_AGING | SW_SRC_ADDR_FILTER);
+
+ /* disable interrupts */
+ ksz_write32(dev, REG_SW_INT_MASK__4, SWITCH_INT_MASK);
+ ksz_write32(dev, REG_SW_PORT_INT_MASK__4, 0x7F);
+ ksz_read32(dev, REG_SW_PORT_INT_STATUS__4, &data32);
+
+ /* set broadcast storm protection 10% rate */
+ regmap_update_bits(dev->regmap[1], REG_SW_MAC_CTRL_2,
+ BROADCAST_STORM_RATE,
+ (BROADCAST_STORM_VALUE *
+ BROADCAST_STORM_PROT_RATE) / 100);
+
+ if (dev->synclko_125)
+ ksz_write8(dev, REG_SW_GLOBAL_OUTPUT_CTRL__1,
+ SW_ENABLE_REFCLKO | SW_REFCLKO_IS_125MHZ);
+
+ return 0;
+}
+
+static void ksz9477_r_mib_cnt(struct ksz_device *dev, int port, u16 addr,
+ u64 *cnt)
+{
+ struct ksz_port *p = &dev->ports[port];
+ unsigned int val;
+ u32 data;
+ int ret;
+
+ /* retain the flush/freeze bit */
+ data = p->freeze ? MIB_COUNTER_FLUSH_FREEZE : 0;
+ data |= MIB_COUNTER_READ;
+ data |= (addr << MIB_COUNTER_INDEX_S);
+ ksz_pwrite32(dev, port, REG_PORT_MIB_CTRL_STAT__4, data);
+
+ ret = regmap_read_poll_timeout(dev->regmap[2],
+ PORT_CTRL_ADDR(port, REG_PORT_MIB_CTRL_STAT__4),
+ val, !(val & MIB_COUNTER_READ), 10, 1000);
+ /* failed to read MIB. get out of loop */
+ if (ret) {
+ dev_dbg(dev->dev, "Failed to get MIB\n");
+ return;
+ }
+
+ /* count resets upon read */
+ ksz_pread32(dev, port, REG_PORT_MIB_DATA, &data);
+ *cnt += data;
+}
+
+static void ksz9477_r_mib_pkt(struct ksz_device *dev, int port, u16 addr,
+ u64 *dropped, u64 *cnt)
+{
+ addr = ksz9477_mib_names[addr].index;
+ ksz9477_r_mib_cnt(dev, port, addr, cnt);
+}
+
+static void ksz9477_freeze_mib(struct ksz_device *dev, int port, bool freeze)
+{
+ u32 val = freeze ? MIB_COUNTER_FLUSH_FREEZE : 0;
+ struct ksz_port *p = &dev->ports[port];
+
+ /* enable/disable the port for flush/freeze function */
+ mutex_lock(&p->mib.cnt_mutex);
+ ksz_pwrite32(dev, port, REG_PORT_MIB_CTRL_STAT__4, val);
+
+ /* used by MIB counter reading code to know freeze is enabled */
+ p->freeze = freeze;
+ mutex_unlock(&p->mib.cnt_mutex);
+}
+
+static void ksz9477_port_init_cnt(struct ksz_device *dev, int port)
+{
+ struct ksz_port_mib *mib = &dev->ports[port].mib;
+
+ /* flush all enabled port MIB counters */
+ mutex_lock(&mib->cnt_mutex);
+ ksz_pwrite32(dev, port, REG_PORT_MIB_CTRL_STAT__4,
+ MIB_COUNTER_FLUSH_FREEZE);
+ ksz_write8(dev, REG_SW_MAC_CTRL_6, SW_MIB_COUNTER_FLUSH);
+ ksz_pwrite32(dev, port, REG_PORT_MIB_CTRL_STAT__4, 0);
+ mutex_unlock(&mib->cnt_mutex);
+
+ mib->cnt_ptr = 0;
+ memset(mib->counters, 0, dev->mib_cnt * sizeof(u64));
+}
+
+static enum dsa_tag_protocol ksz9477_get_tag_protocol(struct dsa_switch *ds,
+ int port,
+ enum dsa_tag_protocol mp)
+{
+ enum dsa_tag_protocol proto = DSA_TAG_PROTO_KSZ9477;
+ struct ksz_device *dev = ds->priv;
+
+ if (dev->features & IS_9893)
+ proto = DSA_TAG_PROTO_KSZ9893;
+ return proto;
+}
+
+static int ksz9477_phy_read16(struct dsa_switch *ds, int addr, int reg)
+{
+ struct ksz_device *dev = ds->priv;
+ u16 val = 0xffff;
+
+ /* No real PHY after this. Simulate the PHY.
+ * A fixed PHY can be setup in the device tree, but this function is
+ * still called for that port during initialization.
+ * For RGMII PHY there is no way to access it so the fixed PHY should
+ * be used. For SGMII PHY the supporting code will be added later.
+ */
+ if (addr >= dev->phy_port_cnt) {
+ struct ksz_port *p = &dev->ports[addr];
+
+ switch (reg) {
+ case MII_BMCR:
+ val = 0x1140;
+ break;
+ case MII_BMSR:
+ val = 0x796d;
+ break;
+ case MII_PHYSID1:
+ val = 0x0022;
+ break;
+ case MII_PHYSID2:
+ val = 0x1631;
+ break;
+ case MII_ADVERTISE:
+ val = 0x05e1;
+ break;
+ case MII_LPA:
+ val = 0xc5e1;
+ break;
+ case MII_CTRL1000:
+ val = 0x0700;
+ break;
+ case MII_STAT1000:
+ if (p->phydev.speed == SPEED_1000)
+ val = 0x3800;
+ else
+ val = 0;
+ break;
+ }
+ } else {
+ ksz_pread16(dev, addr, 0x100 + (reg << 1), &val);
+ }
+
+ return val;
+}
+
+static int ksz9477_phy_write16(struct dsa_switch *ds, int addr, int reg,
+ u16 val)
+{
+ struct ksz_device *dev = ds->priv;
+
+ /* No real PHY after this. */
+ if (addr >= dev->phy_port_cnt)
+ return 0;
+
+ /* No gigabit support. Do not write to this register. */
+ if (!(dev->features & GBIT_SUPPORT) && reg == MII_CTRL1000)
+ return 0;
+ ksz_pwrite16(dev, addr, 0x100 + (reg << 1), val);
+
+ return 0;
+}
+
+static void ksz9477_get_strings(struct dsa_switch *ds, int port,
+ u32 stringset, uint8_t *buf)
+{
+ int i;
+
+ if (stringset != ETH_SS_STATS)
+ return;
+
+ for (i = 0; i < TOTAL_SWITCH_COUNTER_NUM; i++) {
+ memcpy(buf + i * ETH_GSTRING_LEN, ksz9477_mib_names[i].string,
+ ETH_GSTRING_LEN);
+ }
+}
+
+static void ksz9477_cfg_port_member(struct ksz_device *dev, int port,
+ u8 member)
+{
+ ksz_pwrite32(dev, port, REG_PORT_VLAN_MEMBERSHIP__4, member);
+ dev->ports[port].member = member;
+}
+
+static void ksz9477_port_stp_state_set(struct dsa_switch *ds, int port,
+ u8 state)
+{
+ struct ksz_device *dev = ds->priv;
+ struct ksz_port *p = &dev->ports[port];
+ u8 data;
+ int member = -1;
+ int forward = dev->member;
+
+ ksz_pread8(dev, port, P_STP_CTRL, &data);
+ data &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE | PORT_LEARN_DISABLE);
+
+ switch (state) {
+ case BR_STATE_DISABLED:
+ data |= PORT_LEARN_DISABLE;
+ if (port != dev->cpu_port)
+ member = 0;
+ break;
+ case BR_STATE_LISTENING:
+ data |= (PORT_RX_ENABLE | PORT_LEARN_DISABLE);
+ if (port != dev->cpu_port &&
+ p->stp_state == BR_STATE_DISABLED)
+ member = dev->host_mask | p->vid_member;
+ break;
+ case BR_STATE_LEARNING:
+ data |= PORT_RX_ENABLE;
+ break;
+ case BR_STATE_FORWARDING:
+ data |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
+
+ /* This function is also used internally. */
+ if (port == dev->cpu_port)
+ break;
+
+ member = dev->host_mask | p->vid_member;
+ mutex_lock(&dev->dev_mutex);
+
+ /* Port is a member of a bridge. */
+ if (dev->br_member & (1 << port)) {
+ dev->member |= (1 << port);
+ member = dev->member;
+ }
+ mutex_unlock(&dev->dev_mutex);
+ break;
+ case BR_STATE_BLOCKING:
+ data |= PORT_LEARN_DISABLE;
+ if (port != dev->cpu_port &&
+ p->stp_state == BR_STATE_DISABLED)
+ member = dev->host_mask | p->vid_member;
+ break;
+ default:
+ dev_err(ds->dev, "invalid STP state: %d\n", state);
+ return;
+ }
+
+ ksz_pwrite8(dev, port, P_STP_CTRL, data);
+ p->stp_state = state;
+ mutex_lock(&dev->dev_mutex);
+ if (data & PORT_RX_ENABLE)
+ dev->rx_ports |= (1 << port);
+ else
+ dev->rx_ports &= ~(1 << port);
+ if (data & PORT_TX_ENABLE)
+ dev->tx_ports |= (1 << port);
+ else
+ dev->tx_ports &= ~(1 << port);
+
+ /* Port membership may share register with STP state. */
+ if (member >= 0 && member != p->member)
+ ksz9477_cfg_port_member(dev, port, (u8)member);
+
+ /* Check if forwarding needs to be updated. */
+ if (state != BR_STATE_FORWARDING) {
+ if (dev->br_member & (1 << port))
+ dev->member &= ~(1 << port);
+ }
+
+ /* When topology has changed the function ksz_update_port_member
+ * should be called to modify port forwarding behavior.
+ */
+ if (forward != dev->member)
+ ksz_update_port_member(dev, port);
+ mutex_unlock(&dev->dev_mutex);
+}
+
+static void ksz9477_flush_dyn_mac_table(struct ksz_device *dev, int port)
+{
+ u8 data;
+
+ regmap_update_bits(dev->regmap[0], REG_SW_LUE_CTRL_2,
+ SW_FLUSH_OPTION_M << SW_FLUSH_OPTION_S,
+ SW_FLUSH_OPTION_DYN_MAC << SW_FLUSH_OPTION_S);
+
+ if (port < dev->mib_port_cnt) {
+ /* flush individual port */
+ ksz_pread8(dev, port, P_STP_CTRL, &data);
+ if (!(data & PORT_LEARN_DISABLE))
+ ksz_pwrite8(dev, port, P_STP_CTRL,
+ data | PORT_LEARN_DISABLE);
+ ksz_cfg(dev, S_FLUSH_TABLE_CTRL, SW_FLUSH_DYN_MAC_TABLE, true);
+ ksz_pwrite8(dev, port, P_STP_CTRL, data);
+ } else {
+ /* flush all */
+ ksz_cfg(dev, S_FLUSH_TABLE_CTRL, SW_FLUSH_STP_TABLE, true);
+ }
+}
+
+static int ksz9477_port_vlan_filtering(struct dsa_switch *ds, int port,
+ bool flag)
+{
+ struct ksz_device *dev = ds->priv;
+
+ if (flag) {
+ ksz_port_cfg(dev, port, REG_PORT_LUE_CTRL,
+ PORT_VLAN_LOOKUP_VID_0, true);
+ ksz_cfg(dev, REG_SW_LUE_CTRL_0, SW_VLAN_ENABLE, true);
+ } else {
+ ksz_cfg(dev, REG_SW_LUE_CTRL_0, SW_VLAN_ENABLE, false);
+ ksz_port_cfg(dev, port, REG_PORT_LUE_CTRL,
+ PORT_VLAN_LOOKUP_VID_0, false);
+ }
+
+ return 0;
+}
+
+static void ksz9477_port_vlan_add(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ struct ksz_device *dev = ds->priv;
+ u32 vlan_table[3];
+ u16 vid;
+ bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
+
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) {
+ if (ksz9477_get_vlan_table(dev, vid, vlan_table)) {
+ dev_dbg(dev->dev, "Failed to get vlan table\n");
+ return;
+ }
+
+ vlan_table[0] = VLAN_VALID | (vid & VLAN_FID_M);
+ if (untagged)
+ vlan_table[1] |= BIT(port);
+ else
+ vlan_table[1] &= ~BIT(port);
+ vlan_table[1] &= ~(BIT(dev->cpu_port));
+
+ vlan_table[2] |= BIT(port) | BIT(dev->cpu_port);
+
+ if (ksz9477_set_vlan_table(dev, vid, vlan_table)) {
+ dev_dbg(dev->dev, "Failed to set vlan table\n");
+ return;
+ }
+
+ /* change PVID */
+ if (vlan->flags & BRIDGE_VLAN_INFO_PVID)
+ ksz_pwrite16(dev, port, REG_PORT_DEFAULT_VID, vid);
+ }
+}
+
+static int ksz9477_port_vlan_del(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ struct ksz_device *dev = ds->priv;
+ bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
+ u32 vlan_table[3];
+ u16 vid;
+ u16 pvid;
+
+ ksz_pread16(dev, port, REG_PORT_DEFAULT_VID, &pvid);
+ pvid = pvid & 0xFFF;
+
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) {
+ if (ksz9477_get_vlan_table(dev, vid, vlan_table)) {
+ dev_dbg(dev->dev, "Failed to get vlan table\n");
+ return -ETIMEDOUT;
+ }
+
+ vlan_table[2] &= ~BIT(port);
+
+ if (pvid == vid)
+ pvid = 1;
+
+ if (untagged)
+ vlan_table[1] &= ~BIT(port);
+
+ if (ksz9477_set_vlan_table(dev, vid, vlan_table)) {
+ dev_dbg(dev->dev, "Failed to set vlan table\n");
+ return -ETIMEDOUT;
+ }
+ }
+
+ ksz_pwrite16(dev, port, REG_PORT_DEFAULT_VID, pvid);
+
+ return 0;
+}
+
+static int ksz9477_port_fdb_add(struct dsa_switch *ds, int port,
+ const unsigned char *addr, u16 vid)
+{
+ struct ksz_device *dev = ds->priv;
+ u32 alu_table[4];
+ u32 data;
+ int ret = 0;
+
+ mutex_lock(&dev->alu_mutex);
+
+ /* find any entry with mac & vid */
+ data = vid << ALU_FID_INDEX_S;
+ data |= ((addr[0] << 8) | addr[1]);
+ ksz_write32(dev, REG_SW_ALU_INDEX_0, data);
+
+ data = ((addr[2] << 24) | (addr[3] << 16));
+ data |= ((addr[4] << 8) | addr[5]);
+ ksz_write32(dev, REG_SW_ALU_INDEX_1, data);
+
+ /* start read operation */
+ ksz_write32(dev, REG_SW_ALU_CTRL__4, ALU_READ | ALU_START);
+
+ /* wait to be finished */
+ ret = ksz9477_wait_alu_ready(dev);
+ if (ret) {
+ dev_dbg(dev->dev, "Failed to read ALU\n");
+ goto exit;
+ }
+
+ /* read ALU entry */
+ ksz9477_read_table(dev, alu_table);
+
+ /* update ALU entry */
+ alu_table[0] = ALU_V_STATIC_VALID;
+ alu_table[1] |= BIT(port);
+ if (vid)
+ alu_table[1] |= ALU_V_USE_FID;
+ alu_table[2] = (vid << ALU_V_FID_S);
+ alu_table[2] |= ((addr[0] << 8) | addr[1]);
+ alu_table[3] = ((addr[2] << 24) | (addr[3] << 16));
+ alu_table[3] |= ((addr[4] << 8) | addr[5]);
+
+ ksz9477_write_table(dev, alu_table);
+
+ ksz_write32(dev, REG_SW_ALU_CTRL__4, ALU_WRITE | ALU_START);
+
+ /* wait to be finished */
+ ret = ksz9477_wait_alu_ready(dev);
+ if (ret)
+ dev_dbg(dev->dev, "Failed to write ALU\n");
+
+exit:
+ mutex_unlock(&dev->alu_mutex);
+
+ return ret;
+}
+
+static int ksz9477_port_fdb_del(struct dsa_switch *ds, int port,
+ const unsigned char *addr, u16 vid)
+{
+ struct ksz_device *dev = ds->priv;
+ u32 alu_table[4];
+ u32 data;
+ int ret = 0;
+
+ mutex_lock(&dev->alu_mutex);
+
+ /* read any entry with mac & vid */
+ data = vid << ALU_FID_INDEX_S;
+ data |= ((addr[0] << 8) | addr[1]);
+ ksz_write32(dev, REG_SW_ALU_INDEX_0, data);
+
+ data = ((addr[2] << 24) | (addr[3] << 16));
+ data |= ((addr[4] << 8) | addr[5]);
+ ksz_write32(dev, REG_SW_ALU_INDEX_1, data);
+
+ /* start read operation */
+ ksz_write32(dev, REG_SW_ALU_CTRL__4, ALU_READ | ALU_START);
+
+ /* wait to be finished */
+ ret = ksz9477_wait_alu_ready(dev);
+ if (ret) {
+ dev_dbg(dev->dev, "Failed to read ALU\n");
+ goto exit;
+ }
+
+ ksz_read32(dev, REG_SW_ALU_VAL_A, &alu_table[0]);
+ if (alu_table[0] & ALU_V_STATIC_VALID) {
+ ksz_read32(dev, REG_SW_ALU_VAL_B, &alu_table[1]);
+ ksz_read32(dev, REG_SW_ALU_VAL_C, &alu_table[2]);
+ ksz_read32(dev, REG_SW_ALU_VAL_D, &alu_table[3]);
+
+ /* clear forwarding port */
+ alu_table[1] &= ~BIT(port);
+
+ /* if there is no port to forward, clear table */
+ if ((alu_table[1] & ALU_V_PORT_MAP) == 0) {
+ alu_table[0] = 0;
+ alu_table[1] = 0;
+ alu_table[2] = 0;
+ alu_table[3] = 0;
+ }
+ } else {
+ alu_table[0] = 0;
+ alu_table[1] = 0;
+ alu_table[2] = 0;
+ alu_table[3] = 0;
+ }
+
+ ksz9477_write_table(dev, alu_table);
+
+ ksz_write32(dev, REG_SW_ALU_CTRL__4, ALU_WRITE | ALU_START);
+
+ /* wait to be finished */
+ ret = ksz9477_wait_alu_ready(dev);
+ if (ret)
+ dev_dbg(dev->dev, "Failed to write ALU\n");
+
+exit:
+ mutex_unlock(&dev->alu_mutex);
+
+ return ret;
+}
+
+static void ksz9477_convert_alu(struct alu_struct *alu, u32 *alu_table)
+{
+ alu->is_static = !!(alu_table[0] & ALU_V_STATIC_VALID);
+ alu->is_src_filter = !!(alu_table[0] & ALU_V_SRC_FILTER);
+ alu->is_dst_filter = !!(alu_table[0] & ALU_V_DST_FILTER);
+ alu->prio_age = (alu_table[0] >> ALU_V_PRIO_AGE_CNT_S) &
+ ALU_V_PRIO_AGE_CNT_M;
+ alu->mstp = alu_table[0] & ALU_V_MSTP_M;
+
+ alu->is_override = !!(alu_table[1] & ALU_V_OVERRIDE);
+ alu->is_use_fid = !!(alu_table[1] & ALU_V_USE_FID);
+ alu->port_forward = alu_table[1] & ALU_V_PORT_MAP;
+
+ alu->fid = (alu_table[2] >> ALU_V_FID_S) & ALU_V_FID_M;
+
+ alu->mac[0] = (alu_table[2] >> 8) & 0xFF;
+ alu->mac[1] = alu_table[2] & 0xFF;
+ alu->mac[2] = (alu_table[3] >> 24) & 0xFF;
+ alu->mac[3] = (alu_table[3] >> 16) & 0xFF;
+ alu->mac[4] = (alu_table[3] >> 8) & 0xFF;
+ alu->mac[5] = alu_table[3] & 0xFF;
+}
+
+static int ksz9477_port_fdb_dump(struct dsa_switch *ds, int port,
+ dsa_fdb_dump_cb_t *cb, void *data)
+{
+ struct ksz_device *dev = ds->priv;
+ int ret = 0;
+ u32 ksz_data;
+ u32 alu_table[4];
+ struct alu_struct alu;
+ int timeout;
+
+ mutex_lock(&dev->alu_mutex);
+
+ /* start ALU search */
+ ksz_write32(dev, REG_SW_ALU_CTRL__4, ALU_START | ALU_SEARCH);
+
+ do {
+ timeout = 1000;
+ do {
+ ksz_read32(dev, REG_SW_ALU_CTRL__4, &ksz_data);
+ if ((ksz_data & ALU_VALID) || !(ksz_data & ALU_START))
+ break;
+ usleep_range(1, 10);
+ } while (timeout-- > 0);
+
+ if (!timeout) {
+ dev_dbg(dev->dev, "Failed to search ALU\n");
+ ret = -ETIMEDOUT;
+ goto exit;
+ }
+
+ if (!(ksz_data & ALU_VALID))
+ continue;
+
+ /* read ALU table */
+ ksz9477_read_table(dev, alu_table);
+
+ ksz9477_convert_alu(&alu, alu_table);
+
+ if (alu.port_forward & BIT(port)) {
+ ret = cb(alu.mac, alu.fid, alu.is_static, data);
+ if (ret)
+ goto exit;
+ }
+ } while (ksz_data & ALU_START);
+
+exit:
+
+ /* stop ALU search */
+ ksz_write32(dev, REG_SW_ALU_CTRL__4, 0);
+
+ mutex_unlock(&dev->alu_mutex);
+
+ return ret;
+}
+
+static void ksz9477_port_mdb_add(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_mdb *mdb)
+{
+ struct ksz_device *dev = ds->priv;
+ u32 static_table[4];
+ u32 data;
+ int index;
+ u32 mac_hi, mac_lo;
+
+ mac_hi = ((mdb->addr[0] << 8) | mdb->addr[1]);
+ mac_lo = ((mdb->addr[2] << 24) | (mdb->addr[3] << 16));
+ mac_lo |= ((mdb->addr[4] << 8) | mdb->addr[5]);
+
+ mutex_lock(&dev->alu_mutex);
+
+ for (index = 0; index < dev->num_statics; index++) {
+ /* find empty slot first */
+ data = (index << ALU_STAT_INDEX_S) |
+ ALU_STAT_READ | ALU_STAT_START;
+ ksz_write32(dev, REG_SW_ALU_STAT_CTRL__4, data);
+
+ /* wait to be finished */
+ if (ksz9477_wait_alu_sta_ready(dev)) {
+ dev_dbg(dev->dev, "Failed to read ALU STATIC\n");
+ goto exit;
+ }
+
+ /* read ALU static table */
+ ksz9477_read_table(dev, static_table);
+
+ if (static_table[0] & ALU_V_STATIC_VALID) {
+ /* check this has same vid & mac address */
+ if (((static_table[2] >> ALU_V_FID_S) == mdb->vid) &&
+ ((static_table[2] & ALU_V_MAC_ADDR_HI) == mac_hi) &&
+ static_table[3] == mac_lo) {
+ /* found matching one */
+ break;
+ }
+ } else {
+ /* found empty one */
+ break;
+ }
+ }
+
+ /* no available entry */
+ if (index == dev->num_statics)
+ goto exit;
+
+ /* add entry */
+ static_table[0] = ALU_V_STATIC_VALID;
+ static_table[1] |= BIT(port);
+ if (mdb->vid)
+ static_table[1] |= ALU_V_USE_FID;
+ static_table[2] = (mdb->vid << ALU_V_FID_S);
+ static_table[2] |= mac_hi;
+ static_table[3] = mac_lo;
+
+ ksz9477_write_table(dev, static_table);
+
+ data = (index << ALU_STAT_INDEX_S) | ALU_STAT_START;
+ ksz_write32(dev, REG_SW_ALU_STAT_CTRL__4, data);
+
+ /* wait to be finished */
+ if (ksz9477_wait_alu_sta_ready(dev))
+ dev_dbg(dev->dev, "Failed to read ALU STATIC\n");
+
+exit:
+ mutex_unlock(&dev->alu_mutex);
+}
+
+static int ksz9477_port_mdb_del(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_mdb *mdb)
+{
+ struct ksz_device *dev = ds->priv;
+ u32 static_table[4];
+ u32 data;
+ int index;
+ int ret = 0;
+ u32 mac_hi, mac_lo;
+
+ mac_hi = ((mdb->addr[0] << 8) | mdb->addr[1]);
+ mac_lo = ((mdb->addr[2] << 24) | (mdb->addr[3] << 16));
+ mac_lo |= ((mdb->addr[4] << 8) | mdb->addr[5]);
+
+ mutex_lock(&dev->alu_mutex);
+
+ for (index = 0; index < dev->num_statics; index++) {
+ /* find empty slot first */
+ data = (index << ALU_STAT_INDEX_S) |
+ ALU_STAT_READ | ALU_STAT_START;
+ ksz_write32(dev, REG_SW_ALU_STAT_CTRL__4, data);
+
+ /* wait to be finished */
+ ret = ksz9477_wait_alu_sta_ready(dev);
+ if (ret) {
+ dev_dbg(dev->dev, "Failed to read ALU STATIC\n");
+ goto exit;
+ }
+
+ /* read ALU static table */
+ ksz9477_read_table(dev, static_table);
+
+ if (static_table[0] & ALU_V_STATIC_VALID) {
+ /* check this has same vid & mac address */
+
+ if (((static_table[2] >> ALU_V_FID_S) == mdb->vid) &&
+ ((static_table[2] & ALU_V_MAC_ADDR_HI) == mac_hi) &&
+ static_table[3] == mac_lo) {
+ /* found matching one */
+ break;
+ }
+ }
+ }
+
+ /* no available entry */
+ if (index == dev->num_statics)
+ goto exit;
+
+ /* clear port */
+ static_table[1] &= ~BIT(port);
+
+ if ((static_table[1] & ALU_V_PORT_MAP) == 0) {
+ /* delete entry */
+ static_table[0] = 0;
+ static_table[1] = 0;
+ static_table[2] = 0;
+ static_table[3] = 0;
+ }
+
+ ksz9477_write_table(dev, static_table);
+
+ data = (index << ALU_STAT_INDEX_S) | ALU_STAT_START;
+ ksz_write32(dev, REG_SW_ALU_STAT_CTRL__4, data);
+
+ /* wait to be finished */
+ ret = ksz9477_wait_alu_sta_ready(dev);
+ if (ret)
+ dev_dbg(dev->dev, "Failed to read ALU STATIC\n");
+
+exit:
+ mutex_unlock(&dev->alu_mutex);
+
+ return ret;
+}
+
+static int ksz9477_port_mirror_add(struct dsa_switch *ds, int port,
+ struct dsa_mall_mirror_tc_entry *mirror,
+ bool ingress)
+{
+ struct ksz_device *dev = ds->priv;
+
+ if (ingress)
+ ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, true);
+ else
+ ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, true);
+
+ ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_SNIFFER, false);
+
+ /* configure mirror port */
+ ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL,
+ PORT_MIRROR_SNIFFER, true);
+
+ ksz_cfg(dev, S_MIRROR_CTRL, SW_MIRROR_RX_TX, false);
+
+ return 0;
+}
+
+static void ksz9477_port_mirror_del(struct dsa_switch *ds, int port,
+ struct dsa_mall_mirror_tc_entry *mirror)
+{
+ struct ksz_device *dev = ds->priv;
+ u8 data;
+
+ if (mirror->ingress)
+ ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, false);
+ else
+ ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, false);
+
+ ksz_pread8(dev, port, P_MIRROR_CTRL, &data);
+
+ if (!(data & (PORT_MIRROR_RX | PORT_MIRROR_TX)))
+ ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL,
+ PORT_MIRROR_SNIFFER, false);
+}
+
+static bool ksz9477_get_gbit(struct ksz_device *dev, u8 data)
+{
+ bool gbit;
+
+ if (dev->features & NEW_XMII)
+ gbit = !(data & PORT_MII_NOT_1GBIT);
+ else
+ gbit = !!(data & PORT_MII_1000MBIT_S1);
+ return gbit;
+}
+
+static void ksz9477_set_gbit(struct ksz_device *dev, bool gbit, u8 *data)
+{
+ if (dev->features & NEW_XMII) {
+ if (gbit)
+ *data &= ~PORT_MII_NOT_1GBIT;
+ else
+ *data |= PORT_MII_NOT_1GBIT;
+ } else {
+ if (gbit)
+ *data |= PORT_MII_1000MBIT_S1;
+ else
+ *data &= ~PORT_MII_1000MBIT_S1;
+ }
+}
+
+static int ksz9477_get_xmii(struct ksz_device *dev, u8 data)
+{
+ int mode;
+
+ if (dev->features & NEW_XMII) {
+ switch (data & PORT_MII_SEL_M) {
+ case PORT_MII_SEL:
+ mode = 0;
+ break;
+ case PORT_RMII_SEL:
+ mode = 1;
+ break;
+ case PORT_GMII_SEL:
+ mode = 2;
+ break;
+ default:
+ mode = 3;
+ }
+ } else {
+ switch (data & PORT_MII_SEL_M) {
+ case PORT_MII_SEL_S1:
+ mode = 0;
+ break;
+ case PORT_RMII_SEL_S1:
+ mode = 1;
+ break;
+ case PORT_GMII_SEL_S1:
+ mode = 2;
+ break;
+ default:
+ mode = 3;
+ }
+ }
+ return mode;
+}
+
+static void ksz9477_set_xmii(struct ksz_device *dev, int mode, u8 *data)
+{
+ u8 xmii;
+
+ if (dev->features & NEW_XMII) {
+ switch (mode) {
+ case 0:
+ xmii = PORT_MII_SEL;
+ break;
+ case 1:
+ xmii = PORT_RMII_SEL;
+ break;
+ case 2:
+ xmii = PORT_GMII_SEL;
+ break;
+ default:
+ xmii = PORT_RGMII_SEL;
+ break;
+ }
+ } else {
+ switch (mode) {
+ case 0:
+ xmii = PORT_MII_SEL_S1;
+ break;
+ case 1:
+ xmii = PORT_RMII_SEL_S1;
+ break;
+ case 2:
+ xmii = PORT_GMII_SEL_S1;
+ break;
+ default:
+ xmii = PORT_RGMII_SEL_S1;
+ break;
+ }
+ }
+ *data &= ~PORT_MII_SEL_M;
+ *data |= xmii;
+}
+
+static phy_interface_t ksz9477_get_interface(struct ksz_device *dev, int port)
+{
+ phy_interface_t interface;
+ bool gbit;
+ int mode;
+ u8 data8;
+
+ if (port < dev->phy_port_cnt)
+ return PHY_INTERFACE_MODE_NA;
+ ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
+ gbit = ksz9477_get_gbit(dev, data8);
+ mode = ksz9477_get_xmii(dev, data8);
+ switch (mode) {
+ case 2:
+ interface = PHY_INTERFACE_MODE_GMII;
+ if (gbit)
+ break;
+ /* fall through */
+ case 0:
+ interface = PHY_INTERFACE_MODE_MII;
+ break;
+ case 1:
+ interface = PHY_INTERFACE_MODE_RMII;
+ break;
+ default:
+ interface = PHY_INTERFACE_MODE_RGMII;
+ if (data8 & PORT_RGMII_ID_EG_ENABLE)
+ interface = PHY_INTERFACE_MODE_RGMII_TXID;
+ if (data8 & PORT_RGMII_ID_IG_ENABLE) {
+ interface = PHY_INTERFACE_MODE_RGMII_RXID;
+ if (data8 & PORT_RGMII_ID_EG_ENABLE)
+ interface = PHY_INTERFACE_MODE_RGMII_ID;
+ }
+ break;
+ }
+ return interface;
+}
+
+static void ksz9477_port_mmd_write(struct ksz_device *dev, int port,
+ u8 dev_addr, u16 reg_addr, u16 val)
+{
+ ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_SETUP,
+ MMD_SETUP(PORT_MMD_OP_INDEX, dev_addr));
+ ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_INDEX_DATA, reg_addr);
+ ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_SETUP,
+ MMD_SETUP(PORT_MMD_OP_DATA_NO_INCR, dev_addr));
+ ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_INDEX_DATA, val);
+}
+
+static void ksz9477_phy_errata_setup(struct ksz_device *dev, int port)
+{
+ /* Apply PHY settings to address errata listed in
+ * KSZ9477, KSZ9897, KSZ9896, KSZ9567, KSZ8565
+ * Silicon Errata and Data Sheet Clarification documents:
+ *
+ * Register settings are needed to improve PHY receive performance
+ */
+ ksz9477_port_mmd_write(dev, port, 0x01, 0x6f, 0xdd0b);
+ ksz9477_port_mmd_write(dev, port, 0x01, 0x8f, 0x6032);
+ ksz9477_port_mmd_write(dev, port, 0x01, 0x9d, 0x248c);
+ ksz9477_port_mmd_write(dev, port, 0x01, 0x75, 0x0060);
+ ksz9477_port_mmd_write(dev, port, 0x01, 0xd3, 0x7777);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x06, 0x3008);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x08, 0x2001);
+
+ /* Transmit waveform amplitude can be improved
+ * (1000BASE-T, 100BASE-TX, 10BASE-Te)
+ */
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x04, 0x00d0);
+
+ /* Energy Efficient Ethernet (EEE) feature select must
+ * be manually disabled (except on KSZ8565 which is 100Mbit)
+ */
+ if (dev->features & GBIT_SUPPORT)
+ ksz9477_port_mmd_write(dev, port, 0x07, 0x3c, 0x0000);
+
+ /* Register settings are required to meet data sheet
+ * supply current specifications
+ */
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x13, 0x6eff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x14, 0xe6ff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x15, 0x6eff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x16, 0xe6ff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x17, 0x00ff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x18, 0x43ff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x19, 0xc3ff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x1a, 0x6fff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x1b, 0x07ff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x1c, 0x0fff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x1d, 0xe7ff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x1e, 0xefff);
+ ksz9477_port_mmd_write(dev, port, 0x1c, 0x20, 0xeeee);
+}
+
+static void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
+{
+ u8 data8;
+ u8 member;
+ u16 data16;
+ struct ksz_port *p = &dev->ports[port];
+
+ /* enable tag tail for host port */
+ if (cpu_port)
+ ksz_port_cfg(dev, port, REG_PORT_CTRL_0, PORT_TAIL_TAG_ENABLE,
+ true);
+
+ ksz_port_cfg(dev, port, REG_PORT_CTRL_0, PORT_MAC_LOOPBACK, false);
+
+ /* set back pressure */
+ ksz_port_cfg(dev, port, REG_PORT_MAC_CTRL_1, PORT_BACK_PRESSURE, true);
+
+ /* enable broadcast storm limit */
+ ksz_port_cfg(dev, port, P_BCAST_STORM_CTRL, PORT_BROADCAST_STORM, true);
+
+ /* disable DiffServ priority */
+ ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_DIFFSERV_PRIO_ENABLE, false);
+
+ /* replace priority */
+ ksz_port_cfg(dev, port, REG_PORT_MRI_MAC_CTRL, PORT_USER_PRIO_CEILING,
+ false);
+ ksz9477_port_cfg32(dev, port, REG_PORT_MTI_QUEUE_CTRL_0__4,
+ MTI_PVID_REPLACE, false);
+
+ /* enable 802.1p priority */
+ ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_PRIO_ENABLE, true);
+
+ if (port < dev->phy_port_cnt) {
+ /* do not force flow control */
+ ksz_port_cfg(dev, port, REG_PORT_CTRL_0,
+ PORT_FORCE_TX_FLOW_CTRL | PORT_FORCE_RX_FLOW_CTRL,
+ false);
+
+ if (dev->phy_errata_9477)
+ ksz9477_phy_errata_setup(dev, port);
+ } else {
+ /* force flow control */
+ ksz_port_cfg(dev, port, REG_PORT_CTRL_0,
+ PORT_FORCE_TX_FLOW_CTRL | PORT_FORCE_RX_FLOW_CTRL,
+ true);
+
+ /* configure MAC to 1G & RGMII mode */
+ ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
+ switch (dev->interface) {
+ case PHY_INTERFACE_MODE_MII:
+ ksz9477_set_xmii(dev, 0, &data8);
+ ksz9477_set_gbit(dev, false, &data8);
+ p->phydev.speed = SPEED_100;
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ ksz9477_set_xmii(dev, 1, &data8);
+ ksz9477_set_gbit(dev, false, &data8);
+ p->phydev.speed = SPEED_100;
+ break;
+ case PHY_INTERFACE_MODE_GMII:
+ ksz9477_set_xmii(dev, 2, &data8);
+ ksz9477_set_gbit(dev, true, &data8);
+ p->phydev.speed = SPEED_1000;
+ break;
+ default:
+ ksz9477_set_xmii(dev, 3, &data8);
+ ksz9477_set_gbit(dev, true, &data8);
+ data8 &= ~PORT_RGMII_ID_IG_ENABLE;
+ data8 &= ~PORT_RGMII_ID_EG_ENABLE;
+ if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ dev->interface == PHY_INTERFACE_MODE_RGMII_RXID)
+ data8 |= PORT_RGMII_ID_IG_ENABLE;
+ if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ dev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
+ data8 |= PORT_RGMII_ID_EG_ENABLE;
+ p->phydev.speed = SPEED_1000;
+ break;
+ }
+ ksz_pwrite8(dev, port, REG_PORT_XMII_CTRL_1, data8);
+ p->phydev.duplex = 1;
+ }
+ mutex_lock(&dev->dev_mutex);
+ if (cpu_port) {
+ member = dev->port_mask;
+ dev->on_ports = dev->host_mask;
+ dev->live_ports = dev->host_mask;
+ } else {
+ member = dev->host_mask | p->vid_member;
+ dev->on_ports |= (1 << port);
+
+ /* Link was detected before port is enabled. */
+ if (p->phydev.link)
+ dev->live_ports |= (1 << port);
+ }
+ mutex_unlock(&dev->dev_mutex);
+ ksz9477_cfg_port_member(dev, port, member);
+
+ /* clear pending interrupts */
+ if (port < dev->phy_port_cnt)
+ ksz_pread16(dev, port, REG_PORT_PHY_INT_ENABLE, &data16);
+}
+
+static void ksz9477_config_cpu_port(struct dsa_switch *ds)
+{
+ struct ksz_device *dev = ds->priv;
+ struct ksz_port *p;
+ int i;
+
+ ds->num_ports = dev->port_cnt;
+
+ for (i = 0; i < dev->port_cnt; i++) {
+ if (dsa_is_cpu_port(ds, i) && (dev->cpu_ports & (1 << i))) {
+ phy_interface_t interface;
+
+ dev->cpu_port = i;
+ dev->host_mask = (1 << dev->cpu_port);
+ dev->port_mask |= dev->host_mask;
+
+ /* Read from XMII register to determine host port
+ * interface. If set specifically in device tree
+ * note the difference to help debugging.
+ */
+ interface = ksz9477_get_interface(dev, i);
+ if (!dev->interface)
+ dev->interface = interface;
+ if (interface && interface != dev->interface)
+ dev_info(dev->dev,
+ "use %s instead of %s\n",
+ phy_modes(dev->interface),
+ phy_modes(interface));
+
+ /* enable cpu port */
+ ksz9477_port_setup(dev, i, true);
+ p = &dev->ports[dev->cpu_port];
+ p->vid_member = dev->port_mask;
+ p->on = 1;
+ }
+ }
+
+ dev->member = dev->host_mask;
+
+ for (i = 0; i < dev->mib_port_cnt; i++) {
+ if (i == dev->cpu_port)
+ continue;
+ p = &dev->ports[i];
+
+ /* Initialize to non-zero so that ksz_cfg_port_member() will
+ * be called.
+ */
+ p->vid_member = (1 << i);
+ p->member = dev->port_mask;
+ ksz9477_port_stp_state_set(ds, i, BR_STATE_DISABLED);
+ p->on = 1;
+ if (i < dev->phy_port_cnt)
+ p->phy = 1;
+ if (dev->chip_id == 0x00947700 && i == 6) {
+ p->sgmii = 1;
+
+ /* SGMII PHY detection code is not implemented yet. */
+ p->phy = 0;
+ }
+ }
+}
+
+static int ksz9477_setup(struct dsa_switch *ds)
+{
+ struct ksz_device *dev = ds->priv;
+ int ret = 0;
+
+ dev->vlan_cache = devm_kcalloc(dev->dev, sizeof(struct vlan_table),
+ dev->num_vlans, GFP_KERNEL);
+ if (!dev->vlan_cache)
+ return -ENOMEM;
+
+ ret = ksz9477_reset_switch(dev);
+ if (ret) {
+ dev_err(ds->dev, "failed to reset switch\n");
+ return ret;
+ }
+
+ /* Required for port partitioning. */
+ ksz9477_cfg32(dev, REG_SW_QM_CTRL__4, UNICAST_VLAN_BOUNDARY,
+ true);
+
+ /* Do not work correctly with tail tagging. */
+ ksz_cfg(dev, REG_SW_MAC_CTRL_0, SW_CHECK_LENGTH, false);
+
+ /* accept packet up to 2000bytes */
+ ksz_cfg(dev, REG_SW_MAC_CTRL_1, SW_LEGAL_PACKET_DISABLE, true);
+
+ ksz9477_config_cpu_port(ds);
+
+ ksz_cfg(dev, REG_SW_MAC_CTRL_1, MULTICAST_STORM_DISABLE, true);
+
+ /* queue based egress rate limit */
+ ksz_cfg(dev, REG_SW_MAC_CTRL_5, SW_OUT_RATE_LIMIT_QUEUE_BASED, true);
+
+ /* enable global MIB counter freeze function */
+ ksz_cfg(dev, REG_SW_MAC_CTRL_6, SW_MIB_COUNTER_FREEZE, true);
+
+ /* start switch */
+ ksz_cfg(dev, REG_SW_OPERATION, SW_START, true);
+
+ ksz_init_mib_timer(dev);
+
+ return 0;
+}
+
+static const struct dsa_switch_ops ksz9477_switch_ops = {
+ .get_tag_protocol = ksz9477_get_tag_protocol,
+ .setup = ksz9477_setup,
+ .phy_read = ksz9477_phy_read16,
+ .phy_write = ksz9477_phy_write16,
+ .adjust_link = ksz_adjust_link,
+ .port_enable = ksz_enable_port,
+ .port_disable = ksz_disable_port,
+ .get_strings = ksz9477_get_strings,
+ .get_ethtool_stats = ksz_get_ethtool_stats,
+ .get_sset_count = ksz_sset_count,
+ .port_bridge_join = ksz_port_bridge_join,
+ .port_bridge_leave = ksz_port_bridge_leave,
+ .port_stp_state_set = ksz9477_port_stp_state_set,
+ .port_fast_age = ksz_port_fast_age,
+ .port_vlan_filtering = ksz9477_port_vlan_filtering,
+ .port_vlan_prepare = ksz_port_vlan_prepare,
+ .port_vlan_add = ksz9477_port_vlan_add,
+ .port_vlan_del = ksz9477_port_vlan_del,
+ .port_fdb_dump = ksz9477_port_fdb_dump,
+ .port_fdb_add = ksz9477_port_fdb_add,
+ .port_fdb_del = ksz9477_port_fdb_del,
+ .port_mdb_prepare = ksz_port_mdb_prepare,
+ .port_mdb_add = ksz9477_port_mdb_add,
+ .port_mdb_del = ksz9477_port_mdb_del,
+ .port_mirror_add = ksz9477_port_mirror_add,
+ .port_mirror_del = ksz9477_port_mirror_del,
+};
+
+static u32 ksz9477_get_port_addr(int port, int offset)
+{
+ return PORT_CTRL_ADDR(port, offset);
+}
+
+static int ksz9477_switch_detect(struct ksz_device *dev)
+{
+ u8 data8;
+ u8 id_hi;
+ u8 id_lo;
+ u32 id32;
+ int ret;
+
+ /* turn off SPI DO Edge select */
+ ret = ksz_read8(dev, REG_SW_GLOBAL_SERIAL_CTRL_0, &data8);
+ if (ret)
+ return ret;
+
+ data8 &= ~SPI_AUTO_EDGE_DETECTION;
+ ret = ksz_write8(dev, REG_SW_GLOBAL_SERIAL_CTRL_0, data8);
+ if (ret)
+ return ret;
+
+ /* read chip id */
+ ret = ksz_read32(dev, REG_CHIP_ID0__1, &id32);
+ if (ret)
+ return ret;
+ ret = ksz_read8(dev, REG_GLOBAL_OPTIONS, &data8);
+ if (ret)
+ return ret;
+
+ /* Number of ports can be reduced depending on chip. */
+ dev->mib_port_cnt = TOTAL_PORT_NUM;
+ dev->phy_port_cnt = 5;
+
+ /* Default capability is gigabit capable. */
+ dev->features = GBIT_SUPPORT;
+
+ id_hi = (u8)(id32 >> 16);
+ id_lo = (u8)(id32 >> 8);
+ if ((id_lo & 0xf) == 3) {
+ /* Chip is from KSZ9893 design. */
+ dev->features |= IS_9893;
+
+ /* Chip does not support gigabit. */
+ if (data8 & SW_QW_ABLE)
+ dev->features &= ~GBIT_SUPPORT;
+ dev->mib_port_cnt = 3;
+ dev->phy_port_cnt = 2;
+ } else {
+ /* Chip uses new XMII register definitions. */
+ dev->features |= NEW_XMII;
+
+ /* Chip does not support gigabit. */
+ if (!(data8 & SW_GIGABIT_ABLE))
+ dev->features &= ~GBIT_SUPPORT;
+ }
+
+ /* Change chip id to known ones so it can be matched against them. */
+ id32 = (id_hi << 16) | (id_lo << 8);
+
+ dev->chip_id = id32;
+
+ return 0;
+}
+
+struct ksz_chip_data {
+ u32 chip_id;
+ const char *dev_name;
+ int num_vlans;
+ int num_alus;
+ int num_statics;
+ int cpu_ports;
+ int port_cnt;
+ bool phy_errata_9477;
+};
+
+static const struct ksz_chip_data ksz9477_switch_chips[] = {
+ {
+ .chip_id = 0x00947700,
+ .dev_name = "KSZ9477",
+ .num_vlans = 4096,
+ .num_alus = 4096,
+ .num_statics = 16,
+ .cpu_ports = 0x7F, /* can be configured as cpu port */
+ .port_cnt = 7, /* total physical port count */
+ .phy_errata_9477 = true,
+ },
+ {
+ .chip_id = 0x00989700,
+ .dev_name = "KSZ9897",
+ .num_vlans = 4096,
+ .num_alus = 4096,
+ .num_statics = 16,
+ .cpu_ports = 0x7F, /* can be configured as cpu port */
+ .port_cnt = 7, /* total physical port count */
+ .phy_errata_9477 = true,
+ },
+ {
+ .chip_id = 0x00989300,
+ .dev_name = "KSZ9893",
+ .num_vlans = 4096,
+ .num_alus = 4096,
+ .num_statics = 16,
+ .cpu_ports = 0x07, /* can be configured as cpu port */
+ .port_cnt = 3, /* total port count */
+ },
+ {
+ .chip_id = 0x00956700,
+ .dev_name = "KSZ9567",
+ .num_vlans = 4096,
+ .num_alus = 4096,
+ .num_statics = 16,
+ .cpu_ports = 0x7F, /* can be configured as cpu port */
+ .port_cnt = 7, /* total physical port count */
+ .phy_errata_9477 = true,
+ },
+};
+
+static int ksz9477_switch_init(struct ksz_device *dev)
+{
+ int i;
+
+ dev->ds->ops = &ksz9477_switch_ops;
+
+ for (i = 0; i < ARRAY_SIZE(ksz9477_switch_chips); i++) {
+ const struct ksz_chip_data *chip = &ksz9477_switch_chips[i];
+
+ if (dev->chip_id == chip->chip_id) {
+ dev->name = chip->dev_name;
+ dev->num_vlans = chip->num_vlans;
+ dev->num_alus = chip->num_alus;
+ dev->num_statics = chip->num_statics;
+ dev->port_cnt = chip->port_cnt;
+ dev->cpu_ports = chip->cpu_ports;
+ dev->phy_errata_9477 = chip->phy_errata_9477;
+
+ break;
+ }
+ }
+
+ /* no switch found */
+ if (!dev->port_cnt)
+ return -ENODEV;
+
+ dev->port_mask = (1 << dev->port_cnt) - 1;
+
+ dev->reg_mib_cnt = SWITCH_COUNTER_NUM;
+ dev->mib_cnt = TOTAL_SWITCH_COUNTER_NUM;
+
+ i = dev->mib_port_cnt;
+ dev->ports = devm_kzalloc(dev->dev, sizeof(struct ksz_port) * i,
+ GFP_KERNEL);
+ if (!dev->ports)
+ return -ENOMEM;
+ for (i = 0; i < dev->mib_port_cnt; i++) {
+ mutex_init(&dev->ports[i].mib.cnt_mutex);
+ dev->ports[i].mib.counters =
+ devm_kzalloc(dev->dev,
+ sizeof(u64) *
+ (TOTAL_SWITCH_COUNTER_NUM + 1),
+ GFP_KERNEL);
+ if (!dev->ports[i].mib.counters)
+ return -ENOMEM;
+ }
+
+ /* set the real number of ports */
+ dev->ds->num_ports = dev->port_cnt;
+
+ return 0;
+}
+
+static void ksz9477_switch_exit(struct ksz_device *dev)
+{
+ ksz9477_reset_switch(dev);
+}
+
+static const struct ksz_dev_ops ksz9477_dev_ops = {
+ .get_port_addr = ksz9477_get_port_addr,
+ .cfg_port_member = ksz9477_cfg_port_member,
+ .flush_dyn_mac_table = ksz9477_flush_dyn_mac_table,
+ .port_setup = ksz9477_port_setup,
+ .r_mib_cnt = ksz9477_r_mib_cnt,
+ .r_mib_pkt = ksz9477_r_mib_pkt,
+ .freeze_mib = ksz9477_freeze_mib,
+ .port_init_cnt = ksz9477_port_init_cnt,
+ .shutdown = ksz9477_reset_switch,
+ .detect = ksz9477_switch_detect,
+ .init = ksz9477_switch_init,
+ .exit = ksz9477_switch_exit,
+};
+
+int ksz9477_switch_register(struct ksz_device *dev)
+{
+ int ret, i;
+ struct phy_device *phydev;
+
+ ret = ksz_switch_register(dev, &ksz9477_dev_ops);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < dev->phy_port_cnt; ++i) {
+ if (!dsa_is_user_port(dev->ds, i))
+ continue;
+
+ phydev = dsa_to_port(dev->ds, i)->slave->phydev;
+
+ /* The MAC actually cannot run in 1000 half-duplex mode. */
+ phy_remove_link_mode(phydev,
+ ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
+
+ /* PHY does not support gigabit. */
+ if (!(dev->features & GBIT_SUPPORT))
+ phy_remove_link_mode(phydev,
+ ETHTOOL_LINK_MODE_1000baseT_Full_BIT);
+ }
+ return ret;
+}
+EXPORT_SYMBOL(ksz9477_switch_register);
+
+MODULE_AUTHOR("Woojung Huh <Woojung.Huh@microchip.com>");
+MODULE_DESCRIPTION("Microchip KSZ9477 Series Switch DSA Driver");
+MODULE_LICENSE("GPL");
diff --git a/marvell/linux/drivers/net/dsa/microchip/ksz9477_i2c.c b/marvell/linux/drivers/net/dsa/microchip/ksz9477_i2c.c
new file mode 100644
index 0000000..fdffd9e
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/ksz9477_i2c.c
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Microchip KSZ9477 series register access through I2C
+ *
+ * Copyright (C) 2018-2019 Microchip Technology Inc.
+ */
+
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+
+#include "ksz_common.h"
+
+KSZ_REGMAP_TABLE(ksz9477, not_used, 16, 0, 0);
+
+static int ksz9477_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *i2c_id)
+{
+ struct regmap_config rc;
+ struct ksz_device *dev;
+ int i, ret;
+
+ dev = ksz_switch_alloc(&i2c->dev, i2c);
+ if (!dev)
+ return -ENOMEM;
+
+ for (i = 0; i < ARRAY_SIZE(ksz9477_regmap_config); i++) {
+ rc = ksz9477_regmap_config[i];
+ rc.lock_arg = &dev->regmap_mutex;
+ dev->regmap[i] = devm_regmap_init_i2c(i2c, &rc);
+ if (IS_ERR(dev->regmap[i])) {
+ ret = PTR_ERR(dev->regmap[i]);
+ dev_err(&i2c->dev,
+ "Failed to initialize regmap%i: %d\n",
+ ksz9477_regmap_config[i].val_bits, ret);
+ return ret;
+ }
+ }
+
+ if (i2c->dev.platform_data)
+ dev->pdata = i2c->dev.platform_data;
+
+ ret = ksz9477_switch_register(dev);
+
+ /* Main DSA driver may not be started yet. */
+ if (ret)
+ return ret;
+
+ i2c_set_clientdata(i2c, dev);
+
+ return 0;
+}
+
+static int ksz9477_i2c_remove(struct i2c_client *i2c)
+{
+ struct ksz_device *dev = i2c_get_clientdata(i2c);
+
+ ksz_switch_remove(dev);
+
+ return 0;
+}
+
+static void ksz9477_i2c_shutdown(struct i2c_client *i2c)
+{
+ struct ksz_device *dev = i2c_get_clientdata(i2c);
+
+ if (dev && dev->dev_ops->shutdown)
+ dev->dev_ops->shutdown(dev);
+}
+
+static const struct i2c_device_id ksz9477_i2c_id[] = {
+ { "ksz9477-switch", 0 },
+ {},
+};
+
+MODULE_DEVICE_TABLE(i2c, ksz9477_i2c_id);
+
+static const struct of_device_id ksz9477_dt_ids[] = {
+ { .compatible = "microchip,ksz9477" },
+ { .compatible = "microchip,ksz9897" },
+ { .compatible = "microchip,ksz9567" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ksz9477_dt_ids);
+
+static struct i2c_driver ksz9477_i2c_driver = {
+ .driver = {
+ .name = "ksz9477-switch",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(ksz9477_dt_ids),
+ },
+ .probe = ksz9477_i2c_probe,
+ .remove = ksz9477_i2c_remove,
+ .shutdown = ksz9477_i2c_shutdown,
+ .id_table = ksz9477_i2c_id,
+};
+
+module_i2c_driver(ksz9477_i2c_driver);
+
+MODULE_AUTHOR("Tristram Ha <Tristram.Ha@microchip.com>");
+MODULE_DESCRIPTION("Microchip KSZ9477 Series Switch I2C access Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/marvell/linux/drivers/net/dsa/microchip/ksz9477_reg.h b/marvell/linux/drivers/net/dsa/microchip/ksz9477_reg.h
new file mode 100644
index 0000000..16939f2
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/ksz9477_reg.h
@@ -0,0 +1,1665 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Microchip KSZ9477 register definitions
+ *
+ * Copyright (C) 2017-2018 Microchip Technology Inc.
+ */
+
+#ifndef __KSZ9477_REGS_H
+#define __KSZ9477_REGS_H
+
+#define KS_PRIO_M 0x7
+#define KS_PRIO_S 4
+
+/* 0 - Operation */
+#define REG_CHIP_ID0__1 0x0000
+
+#define REG_CHIP_ID1__1 0x0001
+
+#define FAMILY_ID 0x95
+#define FAMILY_ID_94 0x94
+#define FAMILY_ID_95 0x95
+#define FAMILY_ID_85 0x85
+#define FAMILY_ID_98 0x98
+#define FAMILY_ID_88 0x88
+
+#define REG_CHIP_ID2__1 0x0002
+
+#define CHIP_ID_63 0x63
+#define CHIP_ID_66 0x66
+#define CHIP_ID_67 0x67
+#define CHIP_ID_77 0x77
+#define CHIP_ID_93 0x93
+#define CHIP_ID_96 0x96
+#define CHIP_ID_97 0x97
+
+#define REG_CHIP_ID3__1 0x0003
+
+#define SWITCH_REVISION_M 0x0F
+#define SWITCH_REVISION_S 4
+#define SWITCH_RESET 0x01
+
+#define REG_SW_PME_CTRL 0x0006
+
+#define PME_ENABLE BIT(1)
+#define PME_POLARITY BIT(0)
+
+#define REG_GLOBAL_OPTIONS 0x000F
+
+#define SW_GIGABIT_ABLE BIT(6)
+#define SW_REDUNDANCY_ABLE BIT(5)
+#define SW_AVB_ABLE BIT(4)
+#define SW_9567_RL_5_2 0xC
+#define SW_9477_SL_5_2 0xD
+
+#define SW_9896_GL_5_1 0xB
+#define SW_9896_RL_5_1 0x8
+#define SW_9896_SL_5_1 0x9
+
+#define SW_9895_GL_4_1 0x7
+#define SW_9895_RL_4_1 0x4
+#define SW_9895_SL_4_1 0x5
+
+#define SW_9896_RL_4_2 0x6
+
+#define SW_9893_RL_2_1 0x0
+#define SW_9893_SL_2_1 0x1
+#define SW_9893_GL_2_1 0x3
+
+#define SW_QW_ABLE BIT(5)
+#define SW_9893_RN_2_1 0xC
+
+#define REG_SW_INT_STATUS__4 0x0010
+#define REG_SW_INT_MASK__4 0x0014
+
+#define LUE_INT BIT(31)
+#define TRIG_TS_INT BIT(30)
+#define APB_TIMEOUT_INT BIT(29)
+
+#define SWITCH_INT_MASK (TRIG_TS_INT | APB_TIMEOUT_INT)
+
+#define REG_SW_PORT_INT_STATUS__4 0x0018
+#define REG_SW_PORT_INT_MASK__4 0x001C
+#define REG_SW_PHY_INT_STATUS 0x0020
+#define REG_SW_PHY_INT_ENABLE 0x0024
+
+/* 1 - Global */
+#define REG_SW_GLOBAL_SERIAL_CTRL_0 0x0100
+#define SW_SPARE_REG_2 BIT(7)
+#define SW_SPARE_REG_1 BIT(6)
+#define SW_SPARE_REG_0 BIT(5)
+#define SW_BIG_ENDIAN BIT(4)
+#define SPI_AUTO_EDGE_DETECTION BIT(1)
+#define SPI_CLOCK_OUT_RISING_EDGE BIT(0)
+
+#define REG_SW_GLOBAL_OUTPUT_CTRL__1 0x0103
+#define SW_ENABLE_REFCLKO BIT(1)
+#define SW_REFCLKO_IS_125MHZ BIT(0)
+
+#define REG_SW_IBA__4 0x0104
+
+#define SW_IBA_ENABLE BIT(31)
+#define SW_IBA_DA_MATCH BIT(30)
+#define SW_IBA_INIT BIT(29)
+#define SW_IBA_QID_M 0xF
+#define SW_IBA_QID_S 22
+#define SW_IBA_PORT_M 0x2F
+#define SW_IBA_PORT_S 16
+#define SW_IBA_FRAME_TPID_M 0xFFFF
+
+#define REG_SW_APB_TIMEOUT_ADDR__4 0x0108
+
+#define APB_TIMEOUT_ACKNOWLEDGE BIT(31)
+
+#define REG_SW_IBA_SYNC__1 0x010C
+
+#define REG_SW_IO_STRENGTH__1 0x010D
+#define SW_DRIVE_STRENGTH_M 0x7
+#define SW_DRIVE_STRENGTH_2MA 0
+#define SW_DRIVE_STRENGTH_4MA 1
+#define SW_DRIVE_STRENGTH_8MA 2
+#define SW_DRIVE_STRENGTH_12MA 3
+#define SW_DRIVE_STRENGTH_16MA 4
+#define SW_DRIVE_STRENGTH_20MA 5
+#define SW_DRIVE_STRENGTH_24MA 6
+#define SW_DRIVE_STRENGTH_28MA 7
+#define SW_HI_SPEED_DRIVE_STRENGTH_S 4
+#define SW_LO_SPEED_DRIVE_STRENGTH_S 0
+
+#define REG_SW_IBA_STATUS__4 0x0110
+
+#define SW_IBA_REQ BIT(31)
+#define SW_IBA_RESP BIT(30)
+#define SW_IBA_DA_MISMATCH BIT(14)
+#define SW_IBA_FMT_MISMATCH BIT(13)
+#define SW_IBA_CODE_ERROR BIT(12)
+#define SW_IBA_CMD_ERROR BIT(11)
+#define SW_IBA_CMD_LOC_M (BIT(6) - 1)
+
+#define REG_SW_IBA_STATES__4 0x0114
+
+#define SW_IBA_BUF_STATE_S 30
+#define SW_IBA_CMD_STATE_S 28
+#define SW_IBA_RESP_STATE_S 26
+#define SW_IBA_STATE_M 0x3
+#define SW_IBA_PACKET_SIZE_M 0x7F
+#define SW_IBA_PACKET_SIZE_S 16
+#define SW_IBA_FMT_ID_M 0xFFFF
+
+#define REG_SW_IBA_RESULT__4 0x0118
+
+#define SW_IBA_SIZE_S 24
+
+#define SW_IBA_RETRY_CNT_M (BIT(5) - 1)
+
+/* 2 - PHY */
+#define REG_SW_POWER_MANAGEMENT_CTRL 0x0201
+
+#define SW_PLL_POWER_DOWN BIT(5)
+#define SW_POWER_DOWN_MODE 0x3
+#define SW_ENERGY_DETECTION 1
+#define SW_SOFT_POWER_DOWN 2
+#define SW_POWER_SAVING 3
+
+/* 3 - Operation Control */
+#define REG_SW_OPERATION 0x0300
+
+#define SW_DOUBLE_TAG BIT(7)
+#define SW_RESET BIT(1)
+#define SW_START BIT(0)
+
+#define REG_SW_MAC_ADDR_0 0x0302
+#define REG_SW_MAC_ADDR_1 0x0303
+#define REG_SW_MAC_ADDR_2 0x0304
+#define REG_SW_MAC_ADDR_3 0x0305
+#define REG_SW_MAC_ADDR_4 0x0306
+#define REG_SW_MAC_ADDR_5 0x0307
+
+#define REG_SW_MTU__2 0x0308
+
+#define REG_SW_ISP_TPID__2 0x030A
+
+#define REG_SW_HSR_TPID__2 0x030C
+
+#define REG_AVB_STRATEGY__2 0x030E
+
+#define SW_SHAPING_CREDIT_ACCT BIT(1)
+#define SW_POLICING_CREDIT_ACCT BIT(0)
+
+#define REG_SW_LUE_CTRL_0 0x0310
+
+#define SW_VLAN_ENABLE BIT(7)
+#define SW_DROP_INVALID_VID BIT(6)
+#define SW_AGE_CNT_M 0x7
+#define SW_AGE_CNT_S 3
+#define SW_RESV_MCAST_ENABLE BIT(2)
+#define SW_HASH_OPTION_M 0x03
+#define SW_HASH_OPTION_CRC 1
+#define SW_HASH_OPTION_XOR 2
+#define SW_HASH_OPTION_DIRECT 3
+
+#define REG_SW_LUE_CTRL_1 0x0311
+
+#define UNICAST_LEARN_DISABLE BIT(7)
+#define SW_SRC_ADDR_FILTER BIT(6)
+#define SW_FLUSH_STP_TABLE BIT(5)
+#define SW_FLUSH_MSTP_TABLE BIT(4)
+#define SW_FWD_MCAST_SRC_ADDR BIT(3)
+#define SW_AGING_ENABLE BIT(2)
+#define SW_FAST_AGING BIT(1)
+#define SW_LINK_AUTO_AGING BIT(0)
+
+#define REG_SW_LUE_CTRL_2 0x0312
+
+#define SW_TRAP_DOUBLE_TAG BIT(6)
+#define SW_EGRESS_VLAN_FILTER_DYN BIT(5)
+#define SW_EGRESS_VLAN_FILTER_STA BIT(4)
+#define SW_FLUSH_OPTION_M 0x3
+#define SW_FLUSH_OPTION_S 2
+#define SW_FLUSH_OPTION_DYN_MAC 1
+#define SW_FLUSH_OPTION_STA_MAC 2
+#define SW_FLUSH_OPTION_BOTH 3
+#define SW_PRIO_M 0x3
+#define SW_PRIO_DA 0
+#define SW_PRIO_SA 1
+#define SW_PRIO_HIGHEST_DA_SA 2
+#define SW_PRIO_LOWEST_DA_SA 3
+
+#define REG_SW_LUE_CTRL_3 0x0313
+
+#define REG_SW_LUE_INT_STATUS 0x0314
+#define REG_SW_LUE_INT_ENABLE 0x0315
+
+#define LEARN_FAIL_INT BIT(2)
+#define ALMOST_FULL_INT BIT(1)
+#define WRITE_FAIL_INT BIT(0)
+
+#define REG_SW_LUE_INDEX_0__2 0x0316
+
+#define ENTRY_INDEX_M 0x0FFF
+
+#define REG_SW_LUE_INDEX_1__2 0x0318
+
+#define FAIL_INDEX_M 0x03FF
+
+#define REG_SW_LUE_INDEX_2__2 0x031A
+
+#define REG_SW_LUE_UNK_UCAST_CTRL__4 0x0320
+
+#define SW_UNK_UCAST_ENABLE BIT(31)
+
+#define REG_SW_LUE_UNK_MCAST_CTRL__4 0x0324
+
+#define SW_UNK_MCAST_ENABLE BIT(31)
+
+#define REG_SW_LUE_UNK_VID_CTRL__4 0x0328
+
+#define SW_UNK_VID_ENABLE BIT(31)
+
+#define REG_SW_MAC_CTRL_0 0x0330
+
+#define SW_NEW_BACKOFF BIT(7)
+#define SW_CHECK_LENGTH BIT(3)
+#define SW_PAUSE_UNH_MODE BIT(1)
+#define SW_AGGR_BACKOFF BIT(0)
+
+#define REG_SW_MAC_CTRL_1 0x0331
+
+#define MULTICAST_STORM_DISABLE BIT(6)
+#define SW_BACK_PRESSURE BIT(5)
+#define FAIR_FLOW_CTRL BIT(4)
+#define NO_EXC_COLLISION_DROP BIT(3)
+#define SW_JUMBO_PACKET BIT(2)
+#define SW_LEGAL_PACKET_DISABLE BIT(1)
+#define SW_PASS_SHORT_FRAME BIT(0)
+
+#define REG_SW_MAC_CTRL_2 0x0332
+
+#define SW_REPLACE_VID BIT(3)
+#define BROADCAST_STORM_RATE_HI 0x07
+
+#define REG_SW_MAC_CTRL_3 0x0333
+
+#define BROADCAST_STORM_RATE_LO 0xFF
+#define BROADCAST_STORM_RATE 0x07FF
+
+#define REG_SW_MAC_CTRL_4 0x0334
+
+#define SW_PASS_PAUSE BIT(3)
+
+#define REG_SW_MAC_CTRL_5 0x0335
+
+#define SW_OUT_RATE_LIMIT_QUEUE_BASED BIT(3)
+
+#define REG_SW_MAC_CTRL_6 0x0336
+
+#define SW_MIB_COUNTER_FLUSH BIT(7)
+#define SW_MIB_COUNTER_FREEZE BIT(6)
+
+#define REG_SW_MAC_802_1P_MAP_0 0x0338
+#define REG_SW_MAC_802_1P_MAP_1 0x0339
+#define REG_SW_MAC_802_1P_MAP_2 0x033A
+#define REG_SW_MAC_802_1P_MAP_3 0x033B
+
+#define SW_802_1P_MAP_M KS_PRIO_M
+#define SW_802_1P_MAP_S KS_PRIO_S
+
+#define REG_SW_MAC_ISP_CTRL 0x033C
+
+#define REG_SW_MAC_TOS_CTRL 0x033E
+
+#define SW_TOS_DSCP_REMARK BIT(1)
+#define SW_TOS_DSCP_REMAP BIT(0)
+
+#define REG_SW_MAC_TOS_PRIO_0 0x0340
+#define REG_SW_MAC_TOS_PRIO_1 0x0341
+#define REG_SW_MAC_TOS_PRIO_2 0x0342
+#define REG_SW_MAC_TOS_PRIO_3 0x0343
+#define REG_SW_MAC_TOS_PRIO_4 0x0344
+#define REG_SW_MAC_TOS_PRIO_5 0x0345
+#define REG_SW_MAC_TOS_PRIO_6 0x0346
+#define REG_SW_MAC_TOS_PRIO_7 0x0347
+#define REG_SW_MAC_TOS_PRIO_8 0x0348
+#define REG_SW_MAC_TOS_PRIO_9 0x0349
+#define REG_SW_MAC_TOS_PRIO_10 0x034A
+#define REG_SW_MAC_TOS_PRIO_11 0x034B
+#define REG_SW_MAC_TOS_PRIO_12 0x034C
+#define REG_SW_MAC_TOS_PRIO_13 0x034D
+#define REG_SW_MAC_TOS_PRIO_14 0x034E
+#define REG_SW_MAC_TOS_PRIO_15 0x034F
+#define REG_SW_MAC_TOS_PRIO_16 0x0350
+#define REG_SW_MAC_TOS_PRIO_17 0x0351
+#define REG_SW_MAC_TOS_PRIO_18 0x0352
+#define REG_SW_MAC_TOS_PRIO_19 0x0353
+#define REG_SW_MAC_TOS_PRIO_20 0x0354
+#define REG_SW_MAC_TOS_PRIO_21 0x0355
+#define REG_SW_MAC_TOS_PRIO_22 0x0356
+#define REG_SW_MAC_TOS_PRIO_23 0x0357
+#define REG_SW_MAC_TOS_PRIO_24 0x0358
+#define REG_SW_MAC_TOS_PRIO_25 0x0359
+#define REG_SW_MAC_TOS_PRIO_26 0x035A
+#define REG_SW_MAC_TOS_PRIO_27 0x035B
+#define REG_SW_MAC_TOS_PRIO_28 0x035C
+#define REG_SW_MAC_TOS_PRIO_29 0x035D
+#define REG_SW_MAC_TOS_PRIO_30 0x035E
+#define REG_SW_MAC_TOS_PRIO_31 0x035F
+
+#define REG_SW_MRI_CTRL_0 0x0370
+
+#define SW_IGMP_SNOOP BIT(6)
+#define SW_IPV6_MLD_OPTION BIT(3)
+#define SW_IPV6_MLD_SNOOP BIT(2)
+#define SW_MIRROR_RX_TX BIT(0)
+
+#define REG_SW_CLASS_D_IP_CTRL__4 0x0374
+
+#define SW_CLASS_D_IP_ENABLE BIT(31)
+
+#define REG_SW_MRI_CTRL_8 0x0378
+
+#define SW_NO_COLOR_S 6
+#define SW_RED_COLOR_S 4
+#define SW_YELLOW_COLOR_S 2
+#define SW_GREEN_COLOR_S 0
+#define SW_COLOR_M 0x3
+
+#define REG_SW_QM_CTRL__4 0x0390
+
+#define PRIO_SCHEME_SELECT_M KS_PRIO_M
+#define PRIO_SCHEME_SELECT_S 6
+#define PRIO_MAP_3_HI 0
+#define PRIO_MAP_2_HI 2
+#define PRIO_MAP_0_LO 3
+#define UNICAST_VLAN_BOUNDARY BIT(1)
+
+#define REG_SW_EEE_QM_CTRL__2 0x03C0
+
+#define REG_SW_EEE_TXQ_WAIT_TIME__2 0x03C2
+
+/* 4 - */
+#define REG_SW_VLAN_ENTRY__4 0x0400
+
+#define VLAN_VALID BIT(31)
+#define VLAN_FORWARD_OPTION BIT(27)
+#define VLAN_PRIO_M KS_PRIO_M
+#define VLAN_PRIO_S 24
+#define VLAN_MSTP_M 0x7
+#define VLAN_MSTP_S 12
+#define VLAN_FID_M 0x7F
+
+#define REG_SW_VLAN_ENTRY_UNTAG__4 0x0404
+#define REG_SW_VLAN_ENTRY_PORTS__4 0x0408
+
+#define REG_SW_VLAN_ENTRY_INDEX__2 0x040C
+
+#define VLAN_INDEX_M 0x0FFF
+
+#define REG_SW_VLAN_CTRL 0x040E
+
+#define VLAN_START BIT(7)
+#define VLAN_ACTION 0x3
+#define VLAN_WRITE 1
+#define VLAN_READ 2
+#define VLAN_CLEAR 3
+
+#define REG_SW_ALU_INDEX_0 0x0410
+
+#define ALU_FID_INDEX_S 16
+#define ALU_MAC_ADDR_HI 0xFFFF
+
+#define REG_SW_ALU_INDEX_1 0x0414
+
+#define ALU_DIRECT_INDEX_M (BIT(12) - 1)
+
+#define REG_SW_ALU_CTRL__4 0x0418
+
+#define ALU_VALID_CNT_M (BIT(14) - 1)
+#define ALU_VALID_CNT_S 16
+#define ALU_START BIT(7)
+#define ALU_VALID BIT(6)
+#define ALU_DIRECT BIT(2)
+#define ALU_ACTION 0x3
+#define ALU_WRITE 1
+#define ALU_READ 2
+#define ALU_SEARCH 3
+
+#define REG_SW_ALU_STAT_CTRL__4 0x041C
+
+#define ALU_STAT_INDEX_M (BIT(4) - 1)
+#define ALU_STAT_INDEX_S 16
+#define ALU_RESV_MCAST_INDEX_M (BIT(6) - 1)
+#define ALU_STAT_START BIT(7)
+#define ALU_RESV_MCAST_ADDR BIT(1)
+#define ALU_STAT_READ BIT(0)
+
+#define REG_SW_ALU_VAL_A 0x0420
+
+#define ALU_V_STATIC_VALID BIT(31)
+#define ALU_V_SRC_FILTER BIT(30)
+#define ALU_V_DST_FILTER BIT(29)
+#define ALU_V_PRIO_AGE_CNT_M (BIT(3) - 1)
+#define ALU_V_PRIO_AGE_CNT_S 26
+#define ALU_V_MSTP_M 0x7
+
+#define REG_SW_ALU_VAL_B 0x0424
+
+#define ALU_V_OVERRIDE BIT(31)
+#define ALU_V_USE_FID BIT(30)
+#define ALU_V_PORT_MAP (BIT(24) - 1)
+
+#define REG_SW_ALU_VAL_C 0x0428
+
+#define ALU_V_FID_M (BIT(16) - 1)
+#define ALU_V_FID_S 16
+#define ALU_V_MAC_ADDR_HI 0xFFFF
+
+#define REG_SW_ALU_VAL_D 0x042C
+
+#define REG_HSR_ALU_INDEX_0 0x0440
+
+#define REG_HSR_ALU_INDEX_1 0x0444
+
+#define HSR_DST_MAC_INDEX_LO_S 16
+#define HSR_SRC_MAC_INDEX_HI 0xFFFF
+
+#define REG_HSR_ALU_INDEX_2 0x0448
+
+#define HSR_INDEX_MAX BIT(9)
+#define HSR_DIRECT_INDEX_M (HSR_INDEX_MAX - 1)
+
+#define REG_HSR_ALU_INDEX_3 0x044C
+
+#define HSR_PATH_INDEX_M (BIT(4) - 1)
+
+#define REG_HSR_ALU_CTRL__4 0x0450
+
+#define HSR_VALID_CNT_M (BIT(14) - 1)
+#define HSR_VALID_CNT_S 16
+#define HSR_START BIT(7)
+#define HSR_VALID BIT(6)
+#define HSR_SEARCH_END BIT(5)
+#define HSR_DIRECT BIT(2)
+#define HSR_ACTION 0x3
+#define HSR_WRITE 1
+#define HSR_READ 2
+#define HSR_SEARCH 3
+
+#define REG_HSR_ALU_VAL_A 0x0454
+
+#define HSR_V_STATIC_VALID BIT(31)
+#define HSR_V_AGE_CNT_M (BIT(3) - 1)
+#define HSR_V_AGE_CNT_S 26
+#define HSR_V_PATH_ID_M (BIT(4) - 1)
+
+#define REG_HSR_ALU_VAL_B 0x0458
+
+#define REG_HSR_ALU_VAL_C 0x045C
+
+#define HSR_V_DST_MAC_ADDR_LO_S 16
+#define HSR_V_SRC_MAC_ADDR_HI 0xFFFF
+
+#define REG_HSR_ALU_VAL_D 0x0460
+
+#define REG_HSR_ALU_VAL_E 0x0464
+
+#define HSR_V_START_SEQ_1_S 16
+#define HSR_V_START_SEQ_2_S 0
+
+#define REG_HSR_ALU_VAL_F 0x0468
+
+#define HSR_V_EXP_SEQ_1_S 16
+#define HSR_V_EXP_SEQ_2_S 0
+
+#define REG_HSR_ALU_VAL_G 0x046C
+
+#define HSR_V_SEQ_CNT_1_S 16
+#define HSR_V_SEQ_CNT_2_S 0
+
+#define HSR_V_SEQ_M (BIT(16) - 1)
+
+/* 5 - PTP Clock */
+#define REG_PTP_CLK_CTRL 0x0500
+
+#define PTP_STEP_ADJ BIT(6)
+#define PTP_STEP_DIR BIT(5)
+#define PTP_READ_TIME BIT(4)
+#define PTP_LOAD_TIME BIT(3)
+#define PTP_CLK_ADJ_ENABLE BIT(2)
+#define PTP_CLK_ENABLE BIT(1)
+#define PTP_CLK_RESET BIT(0)
+
+#define REG_PTP_RTC_SUB_NANOSEC__2 0x0502
+
+#define PTP_RTC_SUB_NANOSEC_M 0x0007
+
+#define REG_PTP_RTC_NANOSEC 0x0504
+#define REG_PTP_RTC_NANOSEC_H 0x0504
+#define REG_PTP_RTC_NANOSEC_L 0x0506
+
+#define REG_PTP_RTC_SEC 0x0508
+#define REG_PTP_RTC_SEC_H 0x0508
+#define REG_PTP_RTC_SEC_L 0x050A
+
+#define REG_PTP_SUBNANOSEC_RATE 0x050C
+#define REG_PTP_SUBNANOSEC_RATE_H 0x050C
+
+#define PTP_RATE_DIR BIT(31)
+#define PTP_TMP_RATE_ENABLE BIT(30)
+
+#define REG_PTP_SUBNANOSEC_RATE_L 0x050E
+
+#define REG_PTP_RATE_DURATION 0x0510
+#define REG_PTP_RATE_DURATION_H 0x0510
+#define REG_PTP_RATE_DURATION_L 0x0512
+
+#define REG_PTP_MSG_CONF1 0x0514
+
+#define PTP_802_1AS BIT(7)
+#define PTP_ENABLE BIT(6)
+#define PTP_ETH_ENABLE BIT(5)
+#define PTP_IPV4_UDP_ENABLE BIT(4)
+#define PTP_IPV6_UDP_ENABLE BIT(3)
+#define PTP_TC_P2P BIT(2)
+#define PTP_MASTER BIT(1)
+#define PTP_1STEP BIT(0)
+
+#define REG_PTP_MSG_CONF2 0x0516
+
+#define PTP_UNICAST_ENABLE BIT(12)
+#define PTP_ALTERNATE_MASTER BIT(11)
+#define PTP_ALL_HIGH_PRIO BIT(10)
+#define PTP_SYNC_CHECK BIT(9)
+#define PTP_DELAY_CHECK BIT(8)
+#define PTP_PDELAY_CHECK BIT(7)
+#define PTP_DROP_SYNC_DELAY_REQ BIT(5)
+#define PTP_DOMAIN_CHECK BIT(4)
+#define PTP_UDP_CHECKSUM BIT(2)
+
+#define REG_PTP_DOMAIN_VERSION 0x0518
+#define PTP_VERSION_M 0xFF00
+#define PTP_DOMAIN_M 0x00FF
+
+#define REG_PTP_UNIT_INDEX__4 0x0520
+
+#define PTP_UNIT_M 0xF
+
+#define PTP_GPIO_INDEX_S 16
+#define PTP_TSI_INDEX_S 8
+#define PTP_TOU_INDEX_S 0
+
+#define REG_PTP_TRIG_STATUS__4 0x0524
+
+#define TRIG_ERROR_S 16
+#define TRIG_DONE_S 0
+
+#define REG_PTP_INT_STATUS__4 0x0528
+
+#define TRIG_INT_S 16
+#define TS_INT_S 0
+
+#define TRIG_UNIT_M 0x7
+#define TS_UNIT_M 0x3
+
+#define REG_PTP_CTRL_STAT__4 0x052C
+
+#define GPIO_IN BIT(7)
+#define GPIO_OUT BIT(6)
+#define TS_INT_ENABLE BIT(5)
+#define TRIG_ACTIVE BIT(4)
+#define TRIG_ENABLE BIT(3)
+#define TRIG_RESET BIT(2)
+#define TS_ENABLE BIT(1)
+#define TS_RESET BIT(0)
+
+#define GPIO_CTRL_M (GPIO_IN | GPIO_OUT)
+
+#define TRIG_CTRL_M \
+ (TRIG_ACTIVE | TRIG_ENABLE | TRIG_RESET)
+
+#define TS_CTRL_M \
+ (TS_INT_ENABLE | TS_ENABLE | TS_RESET)
+
+#define REG_TRIG_TARGET_NANOSEC 0x0530
+#define REG_TRIG_TARGET_SEC 0x0534
+
+#define REG_TRIG_CTRL__4 0x0538
+
+#define TRIG_CASCADE_ENABLE BIT(31)
+#define TRIG_CASCADE_TAIL BIT(30)
+#define TRIG_CASCADE_UPS_M 0xF
+#define TRIG_CASCADE_UPS_S 26
+#define TRIG_NOW BIT(25)
+#define TRIG_NOTIFY BIT(24)
+#define TRIG_EDGE BIT(23)
+#define TRIG_PATTERN_S 20
+#define TRIG_PATTERN_M 0x7
+#define TRIG_NEG_EDGE 0
+#define TRIG_POS_EDGE 1
+#define TRIG_NEG_PULSE 2
+#define TRIG_POS_PULSE 3
+#define TRIG_NEG_PERIOD 4
+#define TRIG_POS_PERIOD 5
+#define TRIG_REG_OUTPUT 6
+#define TRIG_GPO_S 16
+#define TRIG_GPO_M 0xF
+#define TRIG_CASCADE_ITERATE_CNT_M 0xFFFF
+
+#define REG_TRIG_CYCLE_WIDTH 0x053C
+
+#define REG_TRIG_CYCLE_CNT 0x0540
+
+#define TRIG_CYCLE_CNT_M 0xFFFF
+#define TRIG_CYCLE_CNT_S 16
+#define TRIG_BIT_PATTERN_M 0xFFFF
+
+#define REG_TRIG_ITERATE_TIME 0x0544
+
+#define REG_TRIG_PULSE_WIDTH__4 0x0548
+
+#define TRIG_PULSE_WIDTH_M 0x00FFFFFF
+
+#define REG_TS_CTRL_STAT__4 0x0550
+
+#define TS_EVENT_DETECT_M 0xF
+#define TS_EVENT_DETECT_S 17
+#define TS_EVENT_OVERFLOW BIT(16)
+#define TS_GPI_M 0xF
+#define TS_GPI_S 8
+#define TS_DETECT_RISE BIT(7)
+#define TS_DETECT_FALL BIT(6)
+#define TS_DETECT_S 6
+#define TS_CASCADE_TAIL BIT(5)
+#define TS_CASCADE_UPS_M 0xF
+#define TS_CASCADE_UPS_S 1
+#define TS_CASCADE_ENABLE BIT(0)
+
+#define DETECT_RISE (TS_DETECT_RISE >> TS_DETECT_S)
+#define DETECT_FALL (TS_DETECT_FALL >> TS_DETECT_S)
+
+#define REG_TS_EVENT_0_NANOSEC 0x0554
+#define REG_TS_EVENT_0_SEC 0x0558
+#define REG_TS_EVENT_0_SUB_NANOSEC 0x055C
+
+#define REG_TS_EVENT_1_NANOSEC 0x0560
+#define REG_TS_EVENT_1_SEC 0x0564
+#define REG_TS_EVENT_1_SUB_NANOSEC 0x0568
+
+#define REG_TS_EVENT_2_NANOSEC 0x056C
+#define REG_TS_EVENT_2_SEC 0x0570
+#define REG_TS_EVENT_2_SUB_NANOSEC 0x0574
+
+#define REG_TS_EVENT_3_NANOSEC 0x0578
+#define REG_TS_EVENT_3_SEC 0x057C
+#define REG_TS_EVENT_3_SUB_NANOSEC 0x0580
+
+#define REG_TS_EVENT_4_NANOSEC 0x0584
+#define REG_TS_EVENT_4_SEC 0x0588
+#define REG_TS_EVENT_4_SUB_NANOSEC 0x058C
+
+#define REG_TS_EVENT_5_NANOSEC 0x0590
+#define REG_TS_EVENT_5_SEC 0x0594
+#define REG_TS_EVENT_5_SUB_NANOSEC 0x0598
+
+#define REG_TS_EVENT_6_NANOSEC 0x059C
+#define REG_TS_EVENT_6_SEC 0x05A0
+#define REG_TS_EVENT_6_SUB_NANOSEC 0x05A4
+
+#define REG_TS_EVENT_7_NANOSEC 0x05A8
+#define REG_TS_EVENT_7_SEC 0x05AC
+#define REG_TS_EVENT_7_SUB_NANOSEC 0x05B0
+
+#define TS_EVENT_EDGE_M 0x1
+#define TS_EVENT_EDGE_S 30
+#define TS_EVENT_NANOSEC_M (BIT(30) - 1)
+
+#define TS_EVENT_SUB_NANOSEC_M 0x7
+
+#define TS_EVENT_SAMPLE \
+ (REG_TS_EVENT_1_NANOSEC - REG_TS_EVENT_0_NANOSEC)
+
+#define PORT_CTRL_ADDR(port, addr) ((addr) | (((port) + 1) << 12))
+
+#define REG_GLOBAL_RR_INDEX__1 0x0600
+
+/* DLR */
+#define REG_DLR_SRC_PORT__4 0x0604
+
+#define DLR_SRC_PORT_UNICAST BIT(31)
+#define DLR_SRC_PORT_M 0x3
+#define DLR_SRC_PORT_BOTH 0
+#define DLR_SRC_PORT_EACH 1
+
+#define REG_DLR_IP_ADDR__4 0x0608
+
+#define REG_DLR_CTRL__1 0x0610
+
+#define DLR_RESET_SEQ_ID BIT(3)
+#define DLR_BACKUP_AUTO_ON BIT(2)
+#define DLR_BEACON_TX_ENABLE BIT(1)
+#define DLR_ASSIST_ENABLE BIT(0)
+
+#define REG_DLR_STATE__1 0x0611
+
+#define DLR_NODE_STATE_M 0x3
+#define DLR_NODE_STATE_S 1
+#define DLR_NODE_STATE_IDLE 0
+#define DLR_NODE_STATE_FAULT 1
+#define DLR_NODE_STATE_NORMAL 2
+#define DLR_RING_STATE_FAULT 0
+#define DLR_RING_STATE_NORMAL 1
+
+#define REG_DLR_PRECEDENCE__1 0x0612
+
+#define REG_DLR_BEACON_INTERVAL__4 0x0614
+
+#define REG_DLR_BEACON_TIMEOUT__4 0x0618
+
+#define REG_DLR_TIMEOUT_WINDOW__4 0x061C
+
+#define DLR_TIMEOUT_WINDOW_M (BIT(22) - 1)
+
+#define REG_DLR_VLAN_ID__2 0x0620
+
+#define DLR_VLAN_ID_M (BIT(12) - 1)
+
+#define REG_DLR_DEST_ADDR_0 0x0622
+#define REG_DLR_DEST_ADDR_1 0x0623
+#define REG_DLR_DEST_ADDR_2 0x0624
+#define REG_DLR_DEST_ADDR_3 0x0625
+#define REG_DLR_DEST_ADDR_4 0x0626
+#define REG_DLR_DEST_ADDR_5 0x0627
+
+#define REG_DLR_PORT_MAP__4 0x0628
+
+#define REG_DLR_CLASS__1 0x062C
+
+#define DLR_FRAME_QID_M 0x3
+
+/* HSR */
+#define REG_HSR_PORT_MAP__4 0x0640
+
+#define REG_HSR_ALU_CTRL_0__1 0x0644
+
+#define HSR_DUPLICATE_DISCARD BIT(7)
+#define HSR_NODE_UNICAST BIT(6)
+#define HSR_AGE_CNT_DEFAULT_M 0x7
+#define HSR_AGE_CNT_DEFAULT_S 3
+#define HSR_LEARN_MCAST_DISABLE BIT(2)
+#define HSR_HASH_OPTION_M 0x3
+#define HSR_HASH_DISABLE 0
+#define HSR_HASH_UPPER_BITS 1
+#define HSR_HASH_LOWER_BITS 2
+#define HSR_HASH_XOR_BOTH_BITS 3
+
+#define REG_HSR_ALU_CTRL_1__1 0x0645
+
+#define HSR_LEARN_UCAST_DISABLE BIT(7)
+#define HSR_FLUSH_TABLE BIT(5)
+#define HSR_PROC_MCAST_SRC BIT(3)
+#define HSR_AGING_ENABLE BIT(2)
+
+#define REG_HSR_ALU_CTRL_2__2 0x0646
+
+#define REG_HSR_ALU_AGE_PERIOD__4 0x0648
+
+#define REG_HSR_ALU_INT_STATUS__1 0x064C
+#define REG_HSR_ALU_INT_MASK__1 0x064D
+
+#define HSR_WINDOW_OVERFLOW_INT BIT(3)
+#define HSR_LEARN_FAIL_INT BIT(2)
+#define HSR_ALMOST_FULL_INT BIT(1)
+#define HSR_WRITE_FAIL_INT BIT(0)
+
+#define REG_HSR_ALU_ENTRY_0__2 0x0650
+
+#define HSR_ENTRY_INDEX_M (BIT(10) - 1)
+#define HSR_FAIL_INDEX_M (BIT(8) - 1)
+
+#define REG_HSR_ALU_ENTRY_1__2 0x0652
+
+#define HSR_FAIL_LEARN_INDEX_M (BIT(8) - 1)
+
+#define REG_HSR_ALU_ENTRY_3__2 0x0654
+
+#define HSR_CPU_ACCESS_ENTRY_INDEX_M (BIT(8) - 1)
+
+/* 0 - Operation */
+#define REG_PORT_DEFAULT_VID 0x0000
+
+#define REG_PORT_CUSTOM_VID 0x0002
+#define REG_PORT_AVB_SR_1_VID 0x0004
+#define REG_PORT_AVB_SR_2_VID 0x0006
+
+#define REG_PORT_AVB_SR_1_TYPE 0x0008
+#define REG_PORT_AVB_SR_2_TYPE 0x000A
+
+#define REG_PORT_PME_STATUS 0x0013
+#define REG_PORT_PME_CTRL 0x0017
+
+#define PME_WOL_MAGICPKT BIT(2)
+#define PME_WOL_LINKUP BIT(1)
+#define PME_WOL_ENERGY BIT(0)
+
+#define REG_PORT_INT_STATUS 0x001B
+#define REG_PORT_INT_MASK 0x001F
+
+#define PORT_SGMII_INT BIT(3)
+#define PORT_PTP_INT BIT(2)
+#define PORT_PHY_INT BIT(1)
+#define PORT_ACL_INT BIT(0)
+
+#define PORT_INT_MASK \
+ (PORT_SGMII_INT | PORT_PTP_INT | PORT_PHY_INT | PORT_ACL_INT)
+
+#define REG_PORT_CTRL_0 0x0020
+
+#define PORT_MAC_LOOPBACK BIT(7)
+#define PORT_FORCE_TX_FLOW_CTRL BIT(4)
+#define PORT_FORCE_RX_FLOW_CTRL BIT(3)
+#define PORT_TAIL_TAG_ENABLE BIT(2)
+#define PORT_QUEUE_SPLIT_ENABLE 0x3
+
+#define REG_PORT_CTRL_1 0x0021
+
+#define PORT_SRP_ENABLE 0x3
+
+#define REG_PORT_STATUS_0 0x0030
+
+#define PORT_INTF_SPEED_M 0x3
+#define PORT_INTF_SPEED_S 3
+#define PORT_INTF_FULL_DUPLEX BIT(2)
+#define PORT_TX_FLOW_CTRL BIT(1)
+#define PORT_RX_FLOW_CTRL BIT(0)
+
+#define REG_PORT_STATUS_1 0x0034
+
+/* 1 - PHY */
+#define REG_PORT_PHY_CTRL 0x0100
+
+#define PORT_PHY_RESET BIT(15)
+#define PORT_PHY_LOOPBACK BIT(14)
+#define PORT_SPEED_100MBIT BIT(13)
+#define PORT_AUTO_NEG_ENABLE BIT(12)
+#define PORT_POWER_DOWN BIT(11)
+#define PORT_ISOLATE BIT(10)
+#define PORT_AUTO_NEG_RESTART BIT(9)
+#define PORT_FULL_DUPLEX BIT(8)
+#define PORT_COLLISION_TEST BIT(7)
+#define PORT_SPEED_1000MBIT BIT(6)
+
+#define REG_PORT_PHY_STATUS 0x0102
+
+#define PORT_100BT4_CAPABLE BIT(15)
+#define PORT_100BTX_FD_CAPABLE BIT(14)
+#define PORT_100BTX_CAPABLE BIT(13)
+#define PORT_10BT_FD_CAPABLE BIT(12)
+#define PORT_10BT_CAPABLE BIT(11)
+#define PORT_EXTENDED_STATUS BIT(8)
+#define PORT_MII_SUPPRESS_CAPABLE BIT(6)
+#define PORT_AUTO_NEG_ACKNOWLEDGE BIT(5)
+#define PORT_REMOTE_FAULT BIT(4)
+#define PORT_AUTO_NEG_CAPABLE BIT(3)
+#define PORT_LINK_STATUS BIT(2)
+#define PORT_JABBER_DETECT BIT(1)
+#define PORT_EXTENDED_CAPABILITY BIT(0)
+
+#define REG_PORT_PHY_ID_HI 0x0104
+#define REG_PORT_PHY_ID_LO 0x0106
+
+#define KSZ9477_ID_HI 0x0022
+#define KSZ9477_ID_LO 0x1622
+
+#define REG_PORT_PHY_AUTO_NEGOTIATION 0x0108
+
+#define PORT_AUTO_NEG_NEXT_PAGE BIT(15)
+#define PORT_AUTO_NEG_REMOTE_FAULT BIT(13)
+#define PORT_AUTO_NEG_ASYM_PAUSE BIT(11)
+#define PORT_AUTO_NEG_SYM_PAUSE BIT(10)
+#define PORT_AUTO_NEG_100BT4 BIT(9)
+#define PORT_AUTO_NEG_100BTX_FD BIT(8)
+#define PORT_AUTO_NEG_100BTX BIT(7)
+#define PORT_AUTO_NEG_10BT_FD BIT(6)
+#define PORT_AUTO_NEG_10BT BIT(5)
+#define PORT_AUTO_NEG_SELECTOR 0x001F
+#define PORT_AUTO_NEG_802_3 0x0001
+
+#define PORT_AUTO_NEG_PAUSE \
+ (PORT_AUTO_NEG_ASYM_PAUSE | PORT_AUTO_NEG_SYM_PAUSE)
+
+#define REG_PORT_PHY_REMOTE_CAPABILITY 0x010A
+
+#define PORT_REMOTE_NEXT_PAGE BIT(15)
+#define PORT_REMOTE_ACKNOWLEDGE BIT(14)
+#define PORT_REMOTE_REMOTE_FAULT BIT(13)
+#define PORT_REMOTE_ASYM_PAUSE BIT(11)
+#define PORT_REMOTE_SYM_PAUSE BIT(10)
+#define PORT_REMOTE_100BTX_FD BIT(8)
+#define PORT_REMOTE_100BTX BIT(7)
+#define PORT_REMOTE_10BT_FD BIT(6)
+#define PORT_REMOTE_10BT BIT(5)
+
+#define REG_PORT_PHY_1000_CTRL 0x0112
+
+#define PORT_AUTO_NEG_MANUAL BIT(12)
+#define PORT_AUTO_NEG_MASTER BIT(11)
+#define PORT_AUTO_NEG_MASTER_PREFERRED BIT(10)
+#define PORT_AUTO_NEG_1000BT_FD BIT(9)
+#define PORT_AUTO_NEG_1000BT BIT(8)
+
+#define REG_PORT_PHY_1000_STATUS 0x0114
+
+#define PORT_MASTER_FAULT BIT(15)
+#define PORT_LOCAL_MASTER BIT(14)
+#define PORT_LOCAL_RX_OK BIT(13)
+#define PORT_REMOTE_RX_OK BIT(12)
+#define PORT_REMOTE_1000BT_FD BIT(11)
+#define PORT_REMOTE_1000BT BIT(10)
+#define PORT_REMOTE_IDLE_CNT_M 0x0F
+
+#define PORT_PHY_1000_STATIC_STATUS \
+ (PORT_LOCAL_RX_OK | \
+ PORT_REMOTE_RX_OK | \
+ PORT_REMOTE_1000BT_FD | \
+ PORT_REMOTE_1000BT)
+
+#define REG_PORT_PHY_MMD_SETUP 0x011A
+
+#define PORT_MMD_OP_MODE_M 0x3
+#define PORT_MMD_OP_MODE_S 14
+#define PORT_MMD_OP_INDEX 0
+#define PORT_MMD_OP_DATA_NO_INCR 1
+#define PORT_MMD_OP_DATA_INCR_RW 2
+#define PORT_MMD_OP_DATA_INCR_W 3
+#define PORT_MMD_DEVICE_ID_M 0x1F
+
+#define MMD_SETUP(mode, dev) \
+ (((u16)(mode) << PORT_MMD_OP_MODE_S) | (dev))
+
+#define REG_PORT_PHY_MMD_INDEX_DATA 0x011C
+
+#define MMD_DEVICE_ID_DSP 1
+
+#define MMD_DSP_SQI_CHAN_A 0xAC
+#define MMD_DSP_SQI_CHAN_B 0xAD
+#define MMD_DSP_SQI_CHAN_C 0xAE
+#define MMD_DSP_SQI_CHAN_D 0xAF
+
+#define DSP_SQI_ERR_DETECTED BIT(15)
+#define DSP_SQI_AVG_ERR 0x7FFF
+
+#define MMD_DEVICE_ID_COMMON 2
+
+#define MMD_DEVICE_ID_EEE_ADV 7
+
+#define MMD_EEE_ADV 0x3C
+#define EEE_ADV_100MBIT BIT(1)
+#define EEE_ADV_1GBIT BIT(2)
+
+#define MMD_EEE_LP_ADV 0x3D
+#define MMD_EEE_MSG_CODE 0x3F
+
+#define MMD_DEVICE_ID_AFED 0x1C
+
+#define REG_PORT_PHY_EXTENDED_STATUS 0x011E
+
+#define PORT_100BTX_FD_ABLE BIT(15)
+#define PORT_100BTX_ABLE BIT(14)
+#define PORT_10BT_FD_ABLE BIT(13)
+#define PORT_10BT_ABLE BIT(12)
+
+#define REG_PORT_SGMII_ADDR__4 0x0200
+#define PORT_SGMII_AUTO_INCR BIT(23)
+#define PORT_SGMII_DEVICE_ID_M 0x1F
+#define PORT_SGMII_DEVICE_ID_S 16
+#define PORT_SGMII_ADDR_M (BIT(21) - 1)
+
+#define REG_PORT_SGMII_DATA__4 0x0204
+#define PORT_SGMII_DATA_M (BIT(16) - 1)
+
+#define MMD_DEVICE_ID_PMA 0x01
+#define MMD_DEVICE_ID_PCS 0x03
+#define MMD_DEVICE_ID_PHY_XS 0x04
+#define MMD_DEVICE_ID_DTE_XS 0x05
+#define MMD_DEVICE_ID_AN 0x07
+#define MMD_DEVICE_ID_VENDOR_CTRL 0x1E
+#define MMD_DEVICE_ID_VENDOR_MII 0x1F
+
+#define SR_MII MMD_DEVICE_ID_VENDOR_MII
+
+#define MMD_SR_MII_CTRL 0x0000
+
+#define SR_MII_RESET BIT(15)
+#define SR_MII_LOOPBACK BIT(14)
+#define SR_MII_SPEED_100MBIT BIT(13)
+#define SR_MII_AUTO_NEG_ENABLE BIT(12)
+#define SR_MII_POWER_DOWN BIT(11)
+#define SR_MII_AUTO_NEG_RESTART BIT(9)
+#define SR_MII_FULL_DUPLEX BIT(8)
+#define SR_MII_SPEED_1000MBIT BIT(6)
+
+#define MMD_SR_MII_STATUS 0x0001
+#define MMD_SR_MII_ID_1 0x0002
+#define MMD_SR_MII_ID_2 0x0003
+#define MMD_SR_MII_AUTO_NEGOTIATION 0x0004
+
+#define SR_MII_AUTO_NEG_NEXT_PAGE BIT(15)
+#define SR_MII_AUTO_NEG_REMOTE_FAULT_M 0x3
+#define SR_MII_AUTO_NEG_REMOTE_FAULT_S 12
+#define SR_MII_AUTO_NEG_NO_ERROR 0
+#define SR_MII_AUTO_NEG_OFFLINE 1
+#define SR_MII_AUTO_NEG_LINK_FAILURE 2
+#define SR_MII_AUTO_NEG_ERROR 3
+#define SR_MII_AUTO_NEG_PAUSE_M 0x3
+#define SR_MII_AUTO_NEG_PAUSE_S 7
+#define SR_MII_AUTO_NEG_NO_PAUSE 0
+#define SR_MII_AUTO_NEG_ASYM_PAUSE_TX 1
+#define SR_MII_AUTO_NEG_SYM_PAUSE 2
+#define SR_MII_AUTO_NEG_ASYM_PAUSE_RX 3
+#define SR_MII_AUTO_NEG_HALF_DUPLEX BIT(6)
+#define SR_MII_AUTO_NEG_FULL_DUPLEX BIT(5)
+
+#define MMD_SR_MII_REMOTE_CAPABILITY 0x0005
+#define MMD_SR_MII_AUTO_NEG_EXP 0x0006
+#define MMD_SR_MII_AUTO_NEG_EXT 0x000F
+
+#define MMD_SR_MII_DIGITAL_CTRL_1 0x8000
+
+#define MMD_SR_MII_AUTO_NEG_CTRL 0x8001
+
+#define SR_MII_8_BIT BIT(8)
+#define SR_MII_SGMII_LINK_UP BIT(4)
+#define SR_MII_TX_CFG_PHY_MASTER BIT(3)
+#define SR_MII_PCS_MODE_M 0x3
+#define SR_MII_PCS_MODE_S 1
+#define SR_MII_PCS_SGMII 2
+#define SR_MII_AUTO_NEG_COMPLETE_INTR BIT(0)
+
+#define MMD_SR_MII_AUTO_NEG_STATUS 0x8002
+
+#define SR_MII_STAT_LINK_UP BIT(4)
+#define SR_MII_STAT_M 0x3
+#define SR_MII_STAT_S 2
+#define SR_MII_STAT_10_MBPS 0
+#define SR_MII_STAT_100_MBPS 1
+#define SR_MII_STAT_1000_MBPS 2
+#define SR_MII_STAT_FULL_DUPLEX BIT(1)
+
+#define MMD_SR_MII_PHY_CTRL 0x80A0
+
+#define SR_MII_PHY_LANE_SEL_M 0xF
+#define SR_MII_PHY_LANE_SEL_S 8
+#define SR_MII_PHY_WRITE BIT(1)
+#define SR_MII_PHY_START_BUSY BIT(0)
+
+#define MMD_SR_MII_PHY_ADDR 0x80A1
+
+#define SR_MII_PHY_ADDR_M (BIT(16) - 1)
+
+#define MMD_SR_MII_PHY_DATA 0x80A2
+
+#define SR_MII_PHY_DATA_M (BIT(16) - 1)
+
+#define SR_MII_PHY_JTAG_CHIP_ID_HI 0x000C
+#define SR_MII_PHY_JTAG_CHIP_ID_LO 0x000D
+
+#define REG_PORT_PHY_REMOTE_LB_LED 0x0122
+
+#define PORT_REMOTE_LOOPBACK BIT(8)
+#define PORT_LED_SELECT (3 << 6)
+#define PORT_LED_CTRL (3 << 4)
+#define PORT_LED_CTRL_TEST BIT(3)
+#define PORT_10BT_PREAMBLE BIT(2)
+#define PORT_LINK_MD_10BT_ENABLE BIT(1)
+#define PORT_LINK_MD_PASS BIT(0)
+
+#define REG_PORT_PHY_LINK_MD 0x0124
+
+#define PORT_START_CABLE_DIAG BIT(15)
+#define PORT_TX_DISABLE BIT(14)
+#define PORT_CABLE_DIAG_PAIR_M 0x3
+#define PORT_CABLE_DIAG_PAIR_S 12
+#define PORT_CABLE_DIAG_SELECT_M 0x3
+#define PORT_CABLE_DIAG_SELECT_S 10
+#define PORT_CABLE_DIAG_RESULT_M 0x3
+#define PORT_CABLE_DIAG_RESULT_S 8
+#define PORT_CABLE_STAT_NORMAL 0
+#define PORT_CABLE_STAT_OPEN 1
+#define PORT_CABLE_STAT_SHORT 2
+#define PORT_CABLE_STAT_FAILED 3
+#define PORT_CABLE_FAULT_COUNTER 0x00FF
+
+#define REG_PORT_PHY_PMA_STATUS 0x0126
+
+#define PORT_1000_LINK_GOOD BIT(1)
+#define PORT_100_LINK_GOOD BIT(0)
+
+#define REG_PORT_PHY_DIGITAL_STATUS 0x0128
+
+#define PORT_LINK_DETECT BIT(14)
+#define PORT_SIGNAL_DETECT BIT(13)
+#define PORT_PHY_STAT_MDI BIT(12)
+#define PORT_PHY_STAT_MASTER BIT(11)
+
+#define REG_PORT_PHY_RXER_COUNTER 0x012A
+
+#define REG_PORT_PHY_INT_ENABLE 0x0136
+#define REG_PORT_PHY_INT_STATUS 0x0137
+
+#define JABBER_INT BIT(7)
+#define RX_ERR_INT BIT(6)
+#define PAGE_RX_INT BIT(5)
+#define PARALLEL_DETECT_FAULT_INT BIT(4)
+#define LINK_PARTNER_ACK_INT BIT(3)
+#define LINK_DOWN_INT BIT(2)
+#define REMOTE_FAULT_INT BIT(1)
+#define LINK_UP_INT BIT(0)
+
+#define REG_PORT_PHY_DIGITAL_DEBUG_1 0x0138
+
+#define PORT_REG_CLK_SPEED_25_MHZ BIT(14)
+#define PORT_PHY_FORCE_MDI BIT(7)
+#define PORT_PHY_AUTO_MDIX_DISABLE BIT(6)
+
+/* Same as PORT_PHY_LOOPBACK */
+#define PORT_PHY_PCS_LOOPBACK BIT(0)
+
+#define REG_PORT_PHY_DIGITAL_DEBUG_2 0x013A
+
+#define REG_PORT_PHY_DIGITAL_DEBUG_3 0x013C
+
+#define PORT_100BT_FIXED_LATENCY BIT(15)
+
+#define REG_PORT_PHY_PHY_CTRL 0x013E
+
+#define PORT_INT_PIN_HIGH BIT(14)
+#define PORT_ENABLE_JABBER BIT(9)
+#define PORT_STAT_SPEED_1000MBIT BIT(6)
+#define PORT_STAT_SPEED_100MBIT BIT(5)
+#define PORT_STAT_SPEED_10MBIT BIT(4)
+#define PORT_STAT_FULL_DUPLEX BIT(3)
+
+/* Same as PORT_PHY_STAT_MASTER */
+#define PORT_STAT_MASTER BIT(2)
+#define PORT_RESET BIT(1)
+#define PORT_LINK_STATUS_FAIL BIT(0)
+
+/* 3 - xMII */
+#define REG_PORT_XMII_CTRL_0 0x0300
+
+#define PORT_SGMII_SEL BIT(7)
+#define PORT_MII_FULL_DUPLEX BIT(6)
+#define PORT_MII_100MBIT BIT(4)
+#define PORT_GRXC_ENABLE BIT(0)
+
+#define REG_PORT_XMII_CTRL_1 0x0301
+
+#define PORT_RMII_CLK_SEL BIT(7)
+/* S1 */
+#define PORT_MII_1000MBIT_S1 BIT(6)
+/* S2 */
+#define PORT_MII_NOT_1GBIT BIT(6)
+#define PORT_MII_SEL_EDGE BIT(5)
+#define PORT_RGMII_ID_IG_ENABLE BIT(4)
+#define PORT_RGMII_ID_EG_ENABLE BIT(3)
+#define PORT_MII_MAC_MODE BIT(2)
+#define PORT_MII_SEL_M 0x3
+/* S1 */
+#define PORT_MII_SEL_S1 0x0
+#define PORT_RMII_SEL_S1 0x1
+#define PORT_GMII_SEL_S1 0x2
+#define PORT_RGMII_SEL_S1 0x3
+/* S2 */
+#define PORT_RGMII_SEL 0x0
+#define PORT_RMII_SEL 0x1
+#define PORT_GMII_SEL 0x2
+#define PORT_MII_SEL 0x3
+
+/* 4 - MAC */
+#define REG_PORT_MAC_CTRL_0 0x0400
+
+#define PORT_BROADCAST_STORM BIT(1)
+#define PORT_JUMBO_FRAME BIT(0)
+
+#define REG_PORT_MAC_CTRL_1 0x0401
+
+#define PORT_BACK_PRESSURE BIT(3)
+#define PORT_PASS_ALL BIT(0)
+
+#define REG_PORT_MAC_CTRL_2 0x0402
+
+#define PORT_100BT_EEE_DISABLE BIT(7)
+#define PORT_1000BT_EEE_DISABLE BIT(6)
+
+#define REG_PORT_MAC_IN_RATE_LIMIT 0x0403
+
+#define PORT_IN_PORT_BASED_S 6
+#define PORT_RATE_PACKET_BASED_S 5
+#define PORT_IN_FLOW_CTRL_S 4
+#define PORT_COUNT_IFG_S 1
+#define PORT_COUNT_PREAMBLE_S 0
+#define PORT_IN_PORT_BASED BIT(6)
+#define PORT_IN_PACKET_BASED BIT(5)
+#define PORT_IN_FLOW_CTRL BIT(4)
+#define PORT_IN_LIMIT_MODE_M 0x3
+#define PORT_IN_LIMIT_MODE_S 2
+#define PORT_IN_ALL 0
+#define PORT_IN_UNICAST 1
+#define PORT_IN_MULTICAST 2
+#define PORT_IN_BROADCAST 3
+#define PORT_COUNT_IFG BIT(1)
+#define PORT_COUNT_PREAMBLE BIT(0)
+
+#define REG_PORT_IN_RATE_0 0x0410
+#define REG_PORT_IN_RATE_1 0x0411
+#define REG_PORT_IN_RATE_2 0x0412
+#define REG_PORT_IN_RATE_3 0x0413
+#define REG_PORT_IN_RATE_4 0x0414
+#define REG_PORT_IN_RATE_5 0x0415
+#define REG_PORT_IN_RATE_6 0x0416
+#define REG_PORT_IN_RATE_7 0x0417
+
+#define REG_PORT_OUT_RATE_0 0x0420
+#define REG_PORT_OUT_RATE_1 0x0421
+#define REG_PORT_OUT_RATE_2 0x0422
+#define REG_PORT_OUT_RATE_3 0x0423
+
+#define PORT_RATE_LIMIT_M (BIT(7) - 1)
+
+/* 5 - MIB Counters */
+#define REG_PORT_MIB_CTRL_STAT__4 0x0500
+
+#define MIB_COUNTER_OVERFLOW BIT(31)
+#define MIB_COUNTER_VALID BIT(30)
+#define MIB_COUNTER_READ BIT(25)
+#define MIB_COUNTER_FLUSH_FREEZE BIT(24)
+#define MIB_COUNTER_INDEX_M (BIT(8) - 1)
+#define MIB_COUNTER_INDEX_S 16
+#define MIB_COUNTER_DATA_HI_M 0xF
+
+#define REG_PORT_MIB_DATA 0x0504
+
+/* 6 - ACL */
+#define REG_PORT_ACL_0 0x0600
+
+#define ACL_FIRST_RULE_M 0xF
+
+#define REG_PORT_ACL_1 0x0601
+
+#define ACL_MODE_M 0x3
+#define ACL_MODE_S 4
+#define ACL_MODE_DISABLE 0
+#define ACL_MODE_LAYER_2 1
+#define ACL_MODE_LAYER_3 2
+#define ACL_MODE_LAYER_4 3
+#define ACL_ENABLE_M 0x3
+#define ACL_ENABLE_S 2
+#define ACL_ENABLE_2_COUNT 0
+#define ACL_ENABLE_2_TYPE 1
+#define ACL_ENABLE_2_MAC 2
+#define ACL_ENABLE_2_BOTH 3
+#define ACL_ENABLE_3_IP 1
+#define ACL_ENABLE_3_SRC_DST_COMP 2
+#define ACL_ENABLE_4_PROTOCOL 0
+#define ACL_ENABLE_4_TCP_PORT_COMP 1
+#define ACL_ENABLE_4_UDP_PORT_COMP 2
+#define ACL_ENABLE_4_TCP_SEQN_COMP 3
+#define ACL_SRC BIT(1)
+#define ACL_EQUAL BIT(0)
+
+#define REG_PORT_ACL_2 0x0602
+#define REG_PORT_ACL_3 0x0603
+
+#define ACL_MAX_PORT 0xFFFF
+
+#define REG_PORT_ACL_4 0x0604
+#define REG_PORT_ACL_5 0x0605
+
+#define ACL_MIN_PORT 0xFFFF
+#define ACL_IP_ADDR 0xFFFFFFFF
+#define ACL_TCP_SEQNUM 0xFFFFFFFF
+
+#define REG_PORT_ACL_6 0x0606
+
+#define ACL_RESERVED 0xF8
+#define ACL_PORT_MODE_M 0x3
+#define ACL_PORT_MODE_S 1
+#define ACL_PORT_MODE_DISABLE 0
+#define ACL_PORT_MODE_EITHER 1
+#define ACL_PORT_MODE_IN_RANGE 2
+#define ACL_PORT_MODE_OUT_OF_RANGE 3
+
+#define REG_PORT_ACL_7 0x0607
+
+#define ACL_TCP_FLAG_ENABLE BIT(0)
+
+#define REG_PORT_ACL_8 0x0608
+
+#define ACL_TCP_FLAG_M 0xFF
+
+#define REG_PORT_ACL_9 0x0609
+
+#define ACL_TCP_FLAG 0xFF
+#define ACL_ETH_TYPE 0xFFFF
+#define ACL_IP_M 0xFFFFFFFF
+
+#define REG_PORT_ACL_A 0x060A
+
+#define ACL_PRIO_MODE_M 0x3
+#define ACL_PRIO_MODE_S 6
+#define ACL_PRIO_MODE_DISABLE 0
+#define ACL_PRIO_MODE_HIGHER 1
+#define ACL_PRIO_MODE_LOWER 2
+#define ACL_PRIO_MODE_REPLACE 3
+#define ACL_PRIO_M KS_PRIO_M
+#define ACL_PRIO_S 3
+#define ACL_VLAN_PRIO_REPLACE BIT(2)
+#define ACL_VLAN_PRIO_M KS_PRIO_M
+#define ACL_VLAN_PRIO_HI_M 0x3
+
+#define REG_PORT_ACL_B 0x060B
+
+#define ACL_VLAN_PRIO_LO_M 0x8
+#define ACL_VLAN_PRIO_S 7
+#define ACL_MAP_MODE_M 0x3
+#define ACL_MAP_MODE_S 5
+#define ACL_MAP_MODE_DISABLE 0
+#define ACL_MAP_MODE_OR 1
+#define ACL_MAP_MODE_AND 2
+#define ACL_MAP_MODE_REPLACE 3
+
+#define ACL_CNT_M (BIT(11) - 1)
+#define ACL_CNT_S 5
+
+#define REG_PORT_ACL_C 0x060C
+
+#define REG_PORT_ACL_D 0x060D
+#define ACL_MSEC_UNIT BIT(6)
+#define ACL_INTR_MODE BIT(5)
+#define ACL_PORT_MAP 0x7F
+
+#define REG_PORT_ACL_E 0x060E
+#define REG_PORT_ACL_F 0x060F
+
+#define REG_PORT_ACL_BYTE_EN_MSB 0x0610
+#define REG_PORT_ACL_BYTE_EN_LSB 0x0611
+
+#define ACL_ACTION_START 0xA
+#define ACL_ACTION_LEN 4
+#define ACL_INTR_CNT_START 0xD
+#define ACL_RULESET_START 0xE
+#define ACL_RULESET_LEN 2
+#define ACL_TABLE_LEN 16
+
+#define ACL_ACTION_ENABLE 0x003C
+#define ACL_MATCH_ENABLE 0x7FC3
+#define ACL_RULESET_ENABLE 0x8003
+#define ACL_BYTE_ENABLE 0xFFFF
+
+#define REG_PORT_ACL_CTRL_0 0x0612
+
+#define PORT_ACL_WRITE_DONE BIT(6)
+#define PORT_ACL_READ_DONE BIT(5)
+#define PORT_ACL_WRITE BIT(4)
+#define PORT_ACL_INDEX_M 0xF
+
+#define REG_PORT_ACL_CTRL_1 0x0613
+
+/* 8 - Classification and Policing */
+#define REG_PORT_MRI_MIRROR_CTRL 0x0800
+
+#define PORT_MIRROR_RX BIT(6)
+#define PORT_MIRROR_TX BIT(5)
+#define PORT_MIRROR_SNIFFER BIT(1)
+
+#define REG_PORT_MRI_PRIO_CTRL 0x0801
+
+#define PORT_HIGHEST_PRIO BIT(7)
+#define PORT_OR_PRIO BIT(6)
+#define PORT_MAC_PRIO_ENABLE BIT(4)
+#define PORT_VLAN_PRIO_ENABLE BIT(3)
+#define PORT_802_1P_PRIO_ENABLE BIT(2)
+#define PORT_DIFFSERV_PRIO_ENABLE BIT(1)
+#define PORT_ACL_PRIO_ENABLE BIT(0)
+
+#define REG_PORT_MRI_MAC_CTRL 0x0802
+
+#define PORT_USER_PRIO_CEILING BIT(7)
+#define PORT_DROP_NON_VLAN BIT(4)
+#define PORT_DROP_TAG BIT(3)
+#define PORT_BASED_PRIO_M KS_PRIO_M
+#define PORT_BASED_PRIO_S 0
+
+#define REG_PORT_MRI_AUTHEN_CTRL 0x0803
+
+#define PORT_ACL_ENABLE BIT(2)
+#define PORT_AUTHEN_MODE 0x3
+#define PORT_AUTHEN_PASS 0
+#define PORT_AUTHEN_BLOCK 1
+#define PORT_AUTHEN_TRAP 2
+
+#define REG_PORT_MRI_INDEX__4 0x0804
+
+#define MRI_INDEX_P_M 0x7
+#define MRI_INDEX_P_S 16
+#define MRI_INDEX_Q_M 0x3
+#define MRI_INDEX_Q_S 0
+
+#define REG_PORT_MRI_TC_MAP__4 0x0808
+
+#define PORT_TC_MAP_M 0xf
+#define PORT_TC_MAP_S 4
+
+#define REG_PORT_MRI_POLICE_CTRL__4 0x080C
+
+#define POLICE_DROP_ALL BIT(10)
+#define POLICE_PACKET_TYPE_M 0x3
+#define POLICE_PACKET_TYPE_S 8
+#define POLICE_PACKET_DROPPED 0
+#define POLICE_PACKET_GREEN 1
+#define POLICE_PACKET_YELLOW 2
+#define POLICE_PACKET_RED 3
+#define PORT_BASED_POLICING BIT(7)
+#define NON_DSCP_COLOR_M 0x3
+#define NON_DSCP_COLOR_S 5
+#define COLOR_MARK_ENABLE BIT(4)
+#define COLOR_REMAP_ENABLE BIT(3)
+#define POLICE_DROP_SRP BIT(2)
+#define POLICE_COLOR_NOT_AWARE BIT(1)
+#define POLICE_ENABLE BIT(0)
+
+#define REG_PORT_POLICE_COLOR_0__4 0x0810
+#define REG_PORT_POLICE_COLOR_1__4 0x0814
+#define REG_PORT_POLICE_COLOR_2__4 0x0818
+#define REG_PORT_POLICE_COLOR_3__4 0x081C
+
+#define POLICE_COLOR_MAP_S 2
+#define POLICE_COLOR_MAP_M (BIT(POLICE_COLOR_MAP_S) - 1)
+
+#define REG_PORT_POLICE_RATE__4 0x0820
+
+#define POLICE_CIR_S 16
+#define POLICE_PIR_S 0
+
+#define REG_PORT_POLICE_BURST_SIZE__4 0x0824
+
+#define POLICE_BURST_SIZE_M 0x3FFF
+#define POLICE_CBS_S 16
+#define POLICE_PBS_S 0
+
+#define REG_PORT_WRED_PM_CTRL_0__4 0x0830
+
+#define WRED_PM_CTRL_M (BIT(11) - 1)
+
+#define WRED_PM_MAX_THRESHOLD_S 16
+#define WRED_PM_MIN_THRESHOLD_S 0
+
+#define REG_PORT_WRED_PM_CTRL_1__4 0x0834
+
+#define WRED_PM_MULTIPLIER_S 16
+#define WRED_PM_AVG_QUEUE_SIZE_S 0
+
+#define REG_PORT_WRED_QUEUE_CTRL_0__4 0x0840
+#define REG_PORT_WRED_QUEUE_CTRL_1__4 0x0844
+
+#define REG_PORT_WRED_QUEUE_PMON__4 0x0848
+
+#define WRED_RANDOM_DROP_ENABLE BIT(31)
+#define WRED_PMON_FLUSH BIT(30)
+#define WRED_DROP_GYR_DISABLE BIT(29)
+#define WRED_DROP_YR_DISABLE BIT(28)
+#define WRED_DROP_R_DISABLE BIT(27)
+#define WRED_DROP_ALL BIT(26)
+#define WRED_PMON_M (BIT(24) - 1)
+
+/* 9 - Shaping */
+
+#define REG_PORT_MTI_QUEUE_INDEX__4 0x0900
+
+#define REG_PORT_MTI_QUEUE_CTRL_0__4 0x0904
+
+#define MTI_PVID_REPLACE BIT(0)
+
+#define REG_PORT_MTI_QUEUE_CTRL_0 0x0914
+
+#define MTI_SCHEDULE_MODE_M 0x3
+#define MTI_SCHEDULE_MODE_S 6
+#define MTI_SCHEDULE_STRICT_PRIO 0
+#define MTI_SCHEDULE_WRR 2
+#define MTI_SHAPING_M 0x3
+#define MTI_SHAPING_S 4
+#define MTI_SHAPING_OFF 0
+#define MTI_SHAPING_SRP 1
+#define MTI_SHAPING_TIME_AWARE 2
+
+#define REG_PORT_MTI_QUEUE_CTRL_1 0x0915
+
+#define MTI_TX_RATIO_M (BIT(7) - 1)
+
+#define REG_PORT_MTI_QUEUE_CTRL_2__2 0x0916
+#define REG_PORT_MTI_HI_WATER_MARK 0x0916
+#define REG_PORT_MTI_QUEUE_CTRL_3__2 0x0918
+#define REG_PORT_MTI_LO_WATER_MARK 0x0918
+#define REG_PORT_MTI_QUEUE_CTRL_4__2 0x091A
+#define REG_PORT_MTI_CREDIT_INCREMENT 0x091A
+
+/* A - QM */
+
+#define REG_PORT_QM_CTRL__4 0x0A00
+
+#define PORT_QM_DROP_PRIO_M 0x3
+
+#define REG_PORT_VLAN_MEMBERSHIP__4 0x0A04
+
+#define REG_PORT_QM_QUEUE_INDEX__4 0x0A08
+
+#define PORT_QM_QUEUE_INDEX_S 24
+#define PORT_QM_BURST_SIZE_S 16
+#define PORT_QM_MIN_RESV_SPACE_M (BIT(11) - 1)
+
+#define REG_PORT_QM_WATER_MARK__4 0x0A0C
+
+#define PORT_QM_HI_WATER_MARK_S 16
+#define PORT_QM_LO_WATER_MARK_S 0
+#define PORT_QM_WATER_MARK_M (BIT(11) - 1)
+
+#define REG_PORT_QM_TX_CNT_0__4 0x0A10
+
+#define PORT_QM_TX_CNT_USED_S 0
+#define PORT_QM_TX_CNT_M (BIT(11) - 1)
+
+#define REG_PORT_QM_TX_CNT_1__4 0x0A14
+
+#define PORT_QM_TX_CNT_CALCULATED_S 16
+#define PORT_QM_TX_CNT_AVAIL_S 0
+
+/* B - LUE */
+#define REG_PORT_LUE_CTRL 0x0B00
+
+#define PORT_VLAN_LOOKUP_VID_0 BIT(7)
+#define PORT_INGRESS_FILTER BIT(6)
+#define PORT_DISCARD_NON_VID BIT(5)
+#define PORT_MAC_BASED_802_1X BIT(4)
+#define PORT_SRC_ADDR_FILTER BIT(3)
+
+#define REG_PORT_LUE_MSTP_INDEX 0x0B01
+
+#define REG_PORT_LUE_MSTP_STATE 0x0B04
+
+#define PORT_TX_ENABLE BIT(2)
+#define PORT_RX_ENABLE BIT(1)
+#define PORT_LEARN_DISABLE BIT(0)
+
+/* C - PTP */
+
+#define REG_PTP_PORT_RX_DELAY__2 0x0C00
+#define REG_PTP_PORT_TX_DELAY__2 0x0C02
+#define REG_PTP_PORT_ASYM_DELAY__2 0x0C04
+
+#define REG_PTP_PORT_XDELAY_TS 0x0C08
+#define REG_PTP_PORT_XDELAY_TS_H 0x0C08
+#define REG_PTP_PORT_XDELAY_TS_L 0x0C0A
+
+#define REG_PTP_PORT_SYNC_TS 0x0C0C
+#define REG_PTP_PORT_SYNC_TS_H 0x0C0C
+#define REG_PTP_PORT_SYNC_TS_L 0x0C0E
+
+#define REG_PTP_PORT_PDRESP_TS 0x0C10
+#define REG_PTP_PORT_PDRESP_TS_H 0x0C10
+#define REG_PTP_PORT_PDRESP_TS_L 0x0C12
+
+#define REG_PTP_PORT_TX_INT_STATUS__2 0x0C14
+#define REG_PTP_PORT_TX_INT_ENABLE__2 0x0C16
+
+#define PTP_PORT_SYNC_INT BIT(15)
+#define PTP_PORT_XDELAY_REQ_INT BIT(14)
+#define PTP_PORT_PDELAY_RESP_INT BIT(13)
+
+#define REG_PTP_PORT_LINK_DELAY__4 0x0C18
+
+#define PRIO_QUEUES 4
+#define RX_PRIO_QUEUES 8
+
+#define KS_PRIO_IN_REG 2
+
+#define TOTAL_PORT_NUM 7
+
+#define KSZ9477_COUNTER_NUM 0x20
+#define TOTAL_KSZ9477_COUNTER_NUM (KSZ9477_COUNTER_NUM + 2 + 2)
+
+#define SWITCH_COUNTER_NUM KSZ9477_COUNTER_NUM
+#define TOTAL_SWITCH_COUNTER_NUM TOTAL_KSZ9477_COUNTER_NUM
+
+#define P_BCAST_STORM_CTRL REG_PORT_MAC_CTRL_0
+#define P_PRIO_CTRL REG_PORT_MRI_PRIO_CTRL
+#define P_MIRROR_CTRL REG_PORT_MRI_MIRROR_CTRL
+#define P_STP_CTRL REG_PORT_LUE_MSTP_STATE
+#define P_PHY_CTRL REG_PORT_PHY_CTRL
+#define P_NEG_RESTART_CTRL REG_PORT_PHY_CTRL
+#define P_LINK_STATUS REG_PORT_PHY_STATUS
+#define P_SPEED_STATUS REG_PORT_PHY_PHY_CTRL
+#define P_RATE_LIMIT_CTRL REG_PORT_MAC_IN_RATE_LIMIT
+
+#define S_LINK_AGING_CTRL REG_SW_LUE_CTRL_1
+#define S_MIRROR_CTRL REG_SW_MRI_CTRL_0
+#define S_REPLACE_VID_CTRL REG_SW_MAC_CTRL_2
+#define S_802_1P_PRIO_CTRL REG_SW_MAC_802_1P_MAP_0
+#define S_TOS_PRIO_CTRL REG_SW_MAC_TOS_PRIO_0
+#define S_FLUSH_TABLE_CTRL REG_SW_LUE_CTRL_1
+
+#define SW_FLUSH_DYN_MAC_TABLE SW_FLUSH_MSTP_TABLE
+
+#define MAX_TIMESTAMP_UNIT 2
+#define MAX_TRIG_UNIT 3
+#define MAX_TIMESTAMP_EVENT_UNIT 8
+#define MAX_GPIO 4
+
+#define PTP_TRIG_UNIT_M (BIT(MAX_TRIG_UNIT) - 1)
+#define PTP_TS_UNIT_M (BIT(MAX_TIMESTAMP_UNIT) - 1)
+
+/* Driver set switch broadcast storm protection at 10% rate. */
+#define BROADCAST_STORM_PROT_RATE 10
+
+/* 148,800 frames * 67 ms / 100 */
+#define BROADCAST_STORM_VALUE 9969
+
+#endif /* KSZ9477_REGS_H */
diff --git a/marvell/linux/drivers/net/dsa/microchip/ksz9477_spi.c b/marvell/linux/drivers/net/dsa/microchip/ksz9477_spi.c
new file mode 100644
index 0000000..9bda83d
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/ksz9477_spi.c
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Microchip KSZ9477 series register access through SPI
+ *
+ * Copyright (C) 2017-2019 Microchip Technology Inc.
+ */
+
+#include <asm/unaligned.h>
+
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+#include "ksz_common.h"
+
+#define SPI_ADDR_SHIFT 24
+#define SPI_ADDR_ALIGN 3
+#define SPI_TURNAROUND_SHIFT 5
+
+KSZ_REGMAP_TABLE(ksz9477, 32, SPI_ADDR_SHIFT,
+ SPI_TURNAROUND_SHIFT, SPI_ADDR_ALIGN);
+
+static int ksz9477_spi_probe(struct spi_device *spi)
+{
+ struct regmap_config rc;
+ struct ksz_device *dev;
+ int i, ret;
+
+ dev = ksz_switch_alloc(&spi->dev, spi);
+ if (!dev)
+ return -ENOMEM;
+
+ for (i = 0; i < ARRAY_SIZE(ksz9477_regmap_config); i++) {
+ rc = ksz9477_regmap_config[i];
+ rc.lock_arg = &dev->regmap_mutex;
+ dev->regmap[i] = devm_regmap_init_spi(spi, &rc);
+ if (IS_ERR(dev->regmap[i])) {
+ ret = PTR_ERR(dev->regmap[i]);
+ dev_err(&spi->dev,
+ "Failed to initialize regmap%i: %d\n",
+ ksz9477_regmap_config[i].val_bits, ret);
+ return ret;
+ }
+ }
+
+ if (spi->dev.platform_data)
+ dev->pdata = spi->dev.platform_data;
+
+ ret = ksz9477_switch_register(dev);
+
+ /* Main DSA driver may not be started yet. */
+ if (ret)
+ return ret;
+
+ spi_set_drvdata(spi, dev);
+
+ return 0;
+}
+
+static int ksz9477_spi_remove(struct spi_device *spi)
+{
+ struct ksz_device *dev = spi_get_drvdata(spi);
+
+ if (dev)
+ ksz_switch_remove(dev);
+
+ return 0;
+}
+
+static void ksz9477_spi_shutdown(struct spi_device *spi)
+{
+ struct ksz_device *dev = spi_get_drvdata(spi);
+
+ if (dev && dev->dev_ops->shutdown)
+ dev->dev_ops->shutdown(dev);
+}
+
+static const struct of_device_id ksz9477_dt_ids[] = {
+ { .compatible = "microchip,ksz9477" },
+ { .compatible = "microchip,ksz9897" },
+ { .compatible = "microchip,ksz9893" },
+ { .compatible = "microchip,ksz9563" },
+ { .compatible = "microchip,ksz8563" },
+ { .compatible = "microchip,ksz9567" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ksz9477_dt_ids);
+
+static const struct spi_device_id ksz9477_spi_ids[] = {
+ { "ksz9477" },
+ { "ksz9897" },
+ { "ksz9893" },
+ { "ksz9563" },
+ { "ksz8563" },
+ { "ksz9567" },
+ { },
+};
+MODULE_DEVICE_TABLE(spi, ksz9477_spi_ids);
+
+static struct spi_driver ksz9477_spi_driver = {
+ .driver = {
+ .name = "ksz9477-switch",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(ksz9477_dt_ids),
+ },
+ .id_table = ksz9477_spi_ids,
+ .probe = ksz9477_spi_probe,
+ .remove = ksz9477_spi_remove,
+ .shutdown = ksz9477_spi_shutdown,
+};
+
+module_spi_driver(ksz9477_spi_driver);
+
+MODULE_ALIAS("spi:ksz9477");
+MODULE_ALIAS("spi:ksz9897");
+MODULE_ALIAS("spi:ksz9893");
+MODULE_ALIAS("spi:ksz9563");
+MODULE_ALIAS("spi:ksz8563");
+MODULE_ALIAS("spi:ksz9567");
+MODULE_AUTHOR("Woojung Huh <Woojung.Huh@microchip.com>");
+MODULE_DESCRIPTION("Microchip KSZ9477 Series Switch SPI access Driver");
+MODULE_LICENSE("GPL");
diff --git a/marvell/linux/drivers/net/dsa/microchip/ksz_common.c b/marvell/linux/drivers/net/dsa/microchip/ksz_common.c
new file mode 100644
index 0000000..7fabc0e
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/ksz_common.c
@@ -0,0 +1,490 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Microchip switch driver main logic
+ *
+ * Copyright (C) 2017-2019 Microchip Technology Inc.
+ */
+
+#include <linux/delay.h>
+#include <linux/export.h>
+#include <linux/gpio/consumer.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_data/microchip-ksz.h>
+#include <linux/phy.h>
+#include <linux/etherdevice.h>
+#include <linux/if_bridge.h>
+#include <linux/of_net.h>
+#include <net/dsa.h>
+#include <net/switchdev.h>
+
+#include "ksz_common.h"
+
+void ksz_update_port_member(struct ksz_device *dev, int port)
+{
+ struct ksz_port *p;
+ int i;
+
+ for (i = 0; i < dev->port_cnt; i++) {
+ if (i == port || i == dev->cpu_port)
+ continue;
+ p = &dev->ports[i];
+ if (!(dev->member & (1 << i)))
+ continue;
+
+ /* Port is a member of the bridge and is forwarding. */
+ if (p->stp_state == BR_STATE_FORWARDING &&
+ p->member != dev->member)
+ dev->dev_ops->cfg_port_member(dev, i, dev->member);
+ }
+}
+EXPORT_SYMBOL_GPL(ksz_update_port_member);
+
+static void port_r_cnt(struct ksz_device *dev, int port)
+{
+ struct ksz_port_mib *mib = &dev->ports[port].mib;
+ u64 *dropped;
+
+ /* Some ports may not have MIB counters before SWITCH_COUNTER_NUM. */
+ while (mib->cnt_ptr < dev->reg_mib_cnt) {
+ dev->dev_ops->r_mib_cnt(dev, port, mib->cnt_ptr,
+ &mib->counters[mib->cnt_ptr]);
+ ++mib->cnt_ptr;
+ }
+
+ /* last one in storage */
+ dropped = &mib->counters[dev->mib_cnt];
+
+ /* Some ports may not have MIB counters after SWITCH_COUNTER_NUM. */
+ while (mib->cnt_ptr < dev->mib_cnt) {
+ dev->dev_ops->r_mib_pkt(dev, port, mib->cnt_ptr,
+ dropped, &mib->counters[mib->cnt_ptr]);
+ ++mib->cnt_ptr;
+ }
+ mib->cnt_ptr = 0;
+}
+
+static void ksz_mib_read_work(struct work_struct *work)
+{
+ struct ksz_device *dev = container_of(work, struct ksz_device,
+ mib_read);
+ struct ksz_port_mib *mib;
+ struct ksz_port *p;
+ int i;
+
+ for (i = 0; i < dev->mib_port_cnt; i++) {
+ if (dsa_is_unused_port(dev->ds, i))
+ continue;
+
+ p = &dev->ports[i];
+ mib = &p->mib;
+ mutex_lock(&mib->cnt_mutex);
+
+ /* Only read MIB counters when the port is told to do.
+ * If not, read only dropped counters when link is not up.
+ */
+ if (!p->read) {
+ const struct dsa_port *dp = dsa_to_port(dev->ds, i);
+
+ if (!netif_carrier_ok(dp->slave))
+ mib->cnt_ptr = dev->reg_mib_cnt;
+ }
+ port_r_cnt(dev, i);
+ p->read = false;
+ mutex_unlock(&mib->cnt_mutex);
+ }
+}
+
+static void mib_monitor(struct timer_list *t)
+{
+ struct ksz_device *dev = from_timer(dev, t, mib_read_timer);
+
+ mod_timer(&dev->mib_read_timer, jiffies + dev->mib_read_interval);
+ schedule_work(&dev->mib_read);
+}
+
+void ksz_init_mib_timer(struct ksz_device *dev)
+{
+ int i;
+
+ /* Read MIB counters every 30 seconds to avoid overflow. */
+ dev->mib_read_interval = msecs_to_jiffies(30000);
+
+ INIT_WORK(&dev->mib_read, ksz_mib_read_work);
+ timer_setup(&dev->mib_read_timer, mib_monitor, 0);
+
+ for (i = 0; i < dev->mib_port_cnt; i++)
+ dev->dev_ops->port_init_cnt(dev, i);
+
+ /* Start the timer 2 seconds later. */
+ dev->mib_read_timer.expires = jiffies + msecs_to_jiffies(2000);
+ add_timer(&dev->mib_read_timer);
+}
+EXPORT_SYMBOL_GPL(ksz_init_mib_timer);
+
+int ksz_phy_read16(struct dsa_switch *ds, int addr, int reg)
+{
+ struct ksz_device *dev = ds->priv;
+ u16 val = 0xffff;
+
+ dev->dev_ops->r_phy(dev, addr, reg, &val);
+
+ return val;
+}
+EXPORT_SYMBOL_GPL(ksz_phy_read16);
+
+int ksz_phy_write16(struct dsa_switch *ds, int addr, int reg, u16 val)
+{
+ struct ksz_device *dev = ds->priv;
+
+ dev->dev_ops->w_phy(dev, addr, reg, val);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ksz_phy_write16);
+
+void ksz_adjust_link(struct dsa_switch *ds, int port,
+ struct phy_device *phydev)
+{
+ struct ksz_device *dev = ds->priv;
+ struct ksz_port *p = &dev->ports[port];
+
+ /* Read all MIB counters when the link is going down. */
+ if (!phydev->link) {
+ p->read = true;
+ schedule_work(&dev->mib_read);
+ }
+ mutex_lock(&dev->dev_mutex);
+ if (!phydev->link)
+ dev->live_ports &= ~(1 << port);
+ else
+ /* Remember which port is connected and active. */
+ dev->live_ports |= (1 << port) & dev->on_ports;
+ mutex_unlock(&dev->dev_mutex);
+}
+EXPORT_SYMBOL_GPL(ksz_adjust_link);
+
+int ksz_sset_count(struct dsa_switch *ds, int port, int sset)
+{
+ struct ksz_device *dev = ds->priv;
+
+ if (sset != ETH_SS_STATS)
+ return 0;
+
+ return dev->mib_cnt;
+}
+EXPORT_SYMBOL_GPL(ksz_sset_count);
+
+void ksz_get_ethtool_stats(struct dsa_switch *ds, int port, uint64_t *buf)
+{
+ const struct dsa_port *dp = dsa_to_port(ds, port);
+ struct ksz_device *dev = ds->priv;
+ struct ksz_port_mib *mib;
+
+ mib = &dev->ports[port].mib;
+ mutex_lock(&mib->cnt_mutex);
+
+ /* Only read dropped counters if no link. */
+ if (!netif_carrier_ok(dp->slave))
+ mib->cnt_ptr = dev->reg_mib_cnt;
+ port_r_cnt(dev, port);
+ memcpy(buf, mib->counters, dev->mib_cnt * sizeof(u64));
+ mutex_unlock(&mib->cnt_mutex);
+}
+EXPORT_SYMBOL_GPL(ksz_get_ethtool_stats);
+
+int ksz_port_bridge_join(struct dsa_switch *ds, int port,
+ struct net_device *br)
+{
+ struct ksz_device *dev = ds->priv;
+
+ mutex_lock(&dev->dev_mutex);
+ dev->br_member |= (1 << port);
+ mutex_unlock(&dev->dev_mutex);
+
+ /* port_stp_state_set() will be called after to put the port in
+ * appropriate state so there is no need to do anything.
+ */
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ksz_port_bridge_join);
+
+void ksz_port_bridge_leave(struct dsa_switch *ds, int port,
+ struct net_device *br)
+{
+ struct ksz_device *dev = ds->priv;
+
+ mutex_lock(&dev->dev_mutex);
+ dev->br_member &= ~(1 << port);
+ dev->member &= ~(1 << port);
+ mutex_unlock(&dev->dev_mutex);
+
+ /* port_stp_state_set() will be called after to put the port in
+ * forwarding state so there is no need to do anything.
+ */
+}
+EXPORT_SYMBOL_GPL(ksz_port_bridge_leave);
+
+void ksz_port_fast_age(struct dsa_switch *ds, int port)
+{
+ struct ksz_device *dev = ds->priv;
+
+ dev->dev_ops->flush_dyn_mac_table(dev, port);
+}
+EXPORT_SYMBOL_GPL(ksz_port_fast_age);
+
+int ksz_port_vlan_prepare(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ /* nothing needed */
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ksz_port_vlan_prepare);
+
+int ksz_port_fdb_dump(struct dsa_switch *ds, int port, dsa_fdb_dump_cb_t *cb,
+ void *data)
+{
+ struct ksz_device *dev = ds->priv;
+ int ret = 0;
+ u16 i = 0;
+ u16 entries = 0;
+ u8 timestamp = 0;
+ u8 fid;
+ u8 member;
+ struct alu_struct alu;
+
+ do {
+ alu.is_static = false;
+ ret = dev->dev_ops->r_dyn_mac_table(dev, i, alu.mac, &fid,
+ &member, ×tamp,
+ &entries);
+ if (!ret && (member & BIT(port))) {
+ ret = cb(alu.mac, alu.fid, alu.is_static, data);
+ if (ret)
+ break;
+ }
+ i++;
+ } while (i < entries);
+ if (i >= entries)
+ ret = 0;
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(ksz_port_fdb_dump);
+
+int ksz_port_mdb_prepare(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_mdb *mdb)
+{
+ /* nothing to do */
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ksz_port_mdb_prepare);
+
+void ksz_port_mdb_add(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_mdb *mdb)
+{
+ struct ksz_device *dev = ds->priv;
+ struct alu_struct alu;
+ int index;
+ int empty = 0;
+
+ alu.port_forward = 0;
+ for (index = 0; index < dev->num_statics; index++) {
+ if (!dev->dev_ops->r_sta_mac_table(dev, index, &alu)) {
+ /* Found one already in static MAC table. */
+ if (!memcmp(alu.mac, mdb->addr, ETH_ALEN) &&
+ alu.fid == mdb->vid)
+ break;
+ /* Remember the first empty entry. */
+ } else if (!empty) {
+ empty = index + 1;
+ }
+ }
+
+ /* no available entry */
+ if (index == dev->num_statics && !empty)
+ return;
+
+ /* add entry */
+ if (index == dev->num_statics) {
+ index = empty - 1;
+ memset(&alu, 0, sizeof(alu));
+ memcpy(alu.mac, mdb->addr, ETH_ALEN);
+ alu.is_static = true;
+ }
+ alu.port_forward |= BIT(port);
+ if (mdb->vid) {
+ alu.is_use_fid = true;
+
+ /* Need a way to map VID to FID. */
+ alu.fid = mdb->vid;
+ }
+ dev->dev_ops->w_sta_mac_table(dev, index, &alu);
+}
+EXPORT_SYMBOL_GPL(ksz_port_mdb_add);
+
+int ksz_port_mdb_del(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_mdb *mdb)
+{
+ struct ksz_device *dev = ds->priv;
+ struct alu_struct alu;
+ int index;
+ int ret = 0;
+
+ for (index = 0; index < dev->num_statics; index++) {
+ if (!dev->dev_ops->r_sta_mac_table(dev, index, &alu)) {
+ /* Found one already in static MAC table. */
+ if (!memcmp(alu.mac, mdb->addr, ETH_ALEN) &&
+ alu.fid == mdb->vid)
+ break;
+ }
+ }
+
+ /* no available entry */
+ if (index == dev->num_statics)
+ goto exit;
+
+ /* clear port */
+ alu.port_forward &= ~BIT(port);
+ if (!alu.port_forward)
+ alu.is_static = false;
+ dev->dev_ops->w_sta_mac_table(dev, index, &alu);
+
+exit:
+ return ret;
+}
+EXPORT_SYMBOL_GPL(ksz_port_mdb_del);
+
+int ksz_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
+{
+ struct ksz_device *dev = ds->priv;
+
+ if (!dsa_is_user_port(ds, port))
+ return 0;
+
+ /* setup slave port */
+ dev->dev_ops->port_setup(dev, port, false);
+
+ /* port_stp_state_set() will be called after to enable the port so
+ * there is no need to do anything.
+ */
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ksz_enable_port);
+
+void ksz_disable_port(struct dsa_switch *ds, int port)
+{
+ struct ksz_device *dev = ds->priv;
+
+ if (!dsa_is_user_port(ds, port))
+ return;
+
+ dev->on_ports &= ~(1 << port);
+ dev->live_ports &= ~(1 << port);
+
+ /* port_stp_state_set() will be called after to disable the port so
+ * there is no need to do anything.
+ */
+}
+EXPORT_SYMBOL_GPL(ksz_disable_port);
+
+struct ksz_device *ksz_switch_alloc(struct device *base, void *priv)
+{
+ struct dsa_switch *ds;
+ struct ksz_device *swdev;
+
+ ds = dsa_switch_alloc(base, DSA_MAX_PORTS);
+ if (!ds)
+ return NULL;
+
+ swdev = devm_kzalloc(base, sizeof(*swdev), GFP_KERNEL);
+ if (!swdev)
+ return NULL;
+
+ ds->priv = swdev;
+ swdev->dev = base;
+
+ swdev->ds = ds;
+ swdev->priv = priv;
+
+ return swdev;
+}
+EXPORT_SYMBOL(ksz_switch_alloc);
+
+int ksz_switch_register(struct ksz_device *dev,
+ const struct ksz_dev_ops *ops)
+{
+ int ret;
+
+ if (dev->pdata)
+ dev->chip_id = dev->pdata->chip_id;
+
+ dev->reset_gpio = devm_gpiod_get_optional(dev->dev, "reset",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(dev->reset_gpio))
+ return PTR_ERR(dev->reset_gpio);
+
+ if (dev->reset_gpio) {
+ gpiod_set_value_cansleep(dev->reset_gpio, 1);
+ mdelay(10);
+ gpiod_set_value_cansleep(dev->reset_gpio, 0);
+ }
+
+ mutex_init(&dev->dev_mutex);
+ mutex_init(&dev->regmap_mutex);
+ mutex_init(&dev->alu_mutex);
+ mutex_init(&dev->vlan_mutex);
+
+ dev->dev_ops = ops;
+
+ if (dev->dev_ops->detect(dev))
+ return -EINVAL;
+
+ ret = dev->dev_ops->init(dev);
+ if (ret)
+ return ret;
+
+ /* Host port interface will be self detected, or specifically set in
+ * device tree.
+ */
+ if (dev->dev->of_node) {
+ ret = of_get_phy_mode(dev->dev->of_node);
+ if (ret >= 0)
+ dev->interface = ret;
+ dev->synclko_125 = of_property_read_bool(dev->dev->of_node,
+ "microchip,synclko-125");
+ }
+
+ ret = dsa_register_switch(dev->ds);
+ if (ret) {
+ dev->dev_ops->exit(dev);
+ return ret;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(ksz_switch_register);
+
+void ksz_switch_remove(struct ksz_device *dev)
+{
+ /* timer started */
+ if (dev->mib_read_timer.expires) {
+ del_timer_sync(&dev->mib_read_timer);
+ flush_work(&dev->mib_read);
+ }
+
+ dev->dev_ops->exit(dev);
+ dsa_unregister_switch(dev->ds);
+
+ if (dev->reset_gpio)
+ gpiod_set_value_cansleep(dev->reset_gpio, 1);
+
+}
+EXPORT_SYMBOL(ksz_switch_remove);
+
+MODULE_AUTHOR("Woojung Huh <Woojung.Huh@microchip.com>");
+MODULE_DESCRIPTION("Microchip KSZ Series Switch DSA Driver");
+MODULE_LICENSE("GPL");
diff --git a/marvell/linux/drivers/net/dsa/microchip/ksz_common.h b/marvell/linux/drivers/net/dsa/microchip/ksz_common.h
new file mode 100644
index 0000000..d601341
--- /dev/null
+++ b/marvell/linux/drivers/net/dsa/microchip/ksz_common.h
@@ -0,0 +1,336 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Microchip switch driver common header
+ *
+ * Copyright (C) 2017-2019 Microchip Technology Inc.
+ */
+
+#ifndef __KSZ_COMMON_H
+#define __KSZ_COMMON_H
+
+#include <linux/etherdevice.h>
+#include <linux/kernel.h>
+#include <linux/mutex.h>
+#include <linux/phy.h>
+#include <linux/regmap.h>
+#include <net/dsa.h>
+
+struct vlan_table {
+ u32 table[3];
+};
+
+struct ksz_port_mib {
+ struct mutex cnt_mutex; /* structure access */
+ u8 cnt_ptr;
+ u64 *counters;
+};
+
+struct ksz_port {
+ u16 member;
+ u16 vid_member;
+ int stp_state;
+ struct phy_device phydev;
+
+ u32 on:1; /* port is not disabled by hardware */
+ u32 phy:1; /* port has a PHY */
+ u32 fiber:1; /* port is fiber */
+ u32 sgmii:1; /* port is SGMII */
+ u32 force:1;
+ u32 read:1; /* read MIB counters in background */
+ u32 freeze:1; /* MIB counter freeze is enabled */
+
+ struct ksz_port_mib mib;
+};
+
+struct ksz_device {
+ struct dsa_switch *ds;
+ struct ksz_platform_data *pdata;
+ const char *name;
+
+ struct mutex dev_mutex; /* device access */
+ struct mutex regmap_mutex; /* regmap access */
+ struct mutex alu_mutex; /* ALU access */
+ struct mutex vlan_mutex; /* vlan access */
+ const struct ksz_dev_ops *dev_ops;
+
+ struct device *dev;
+ struct regmap *regmap[3];
+
+ void *priv;
+
+ struct gpio_desc *reset_gpio; /* Optional reset GPIO */
+
+ /* chip specific data */
+ u32 chip_id;
+ int num_vlans;
+ int num_alus;
+ int num_statics;
+ int cpu_port; /* port connected to CPU */
+ int cpu_ports; /* port bitmap can be cpu port */
+ int phy_port_cnt;
+ int port_cnt;
+ int reg_mib_cnt;
+ int mib_cnt;
+ int mib_port_cnt;
+ int last_port; /* ports after that not used */
+ phy_interface_t interface;
+ u32 regs_size;
+ bool phy_errata_9477;
+ bool synclko_125;
+
+ struct vlan_table *vlan_cache;
+
+ struct ksz_port *ports;
+ struct timer_list mib_read_timer;
+ struct work_struct mib_read;
+ unsigned long mib_read_interval;
+ u16 br_member;
+ u16 member;
+ u16 live_ports;
+ u16 on_ports; /* ports enabled by DSA */
+ u16 rx_ports;
+ u16 tx_ports;
+ u16 mirror_rx;
+ u16 mirror_tx;
+ u32 features; /* chip specific features */
+ u32 overrides; /* chip functions set by user */
+ u16 host_mask;
+ u16 port_mask;
+};
+
+struct alu_struct {
+ /* entry 1 */
+ u8 is_static:1;
+ u8 is_src_filter:1;
+ u8 is_dst_filter:1;
+ u8 prio_age:3;
+ u32 _reserv_0_1:23;
+ u8 mstp:3;
+ /* entry 2 */
+ u8 is_override:1;
+ u8 is_use_fid:1;
+ u32 _reserv_1_1:23;
+ u8 port_forward:7;
+ /* entry 3 & 4*/
+ u32 _reserv_2_1:9;
+ u8 fid:7;
+ u8 mac[ETH_ALEN];
+};
+
+struct ksz_dev_ops {
+ u32 (*get_port_addr)(int port, int offset);
+ void (*cfg_port_member)(struct ksz_device *dev, int port, u8 member);
+ void (*flush_dyn_mac_table)(struct ksz_device *dev, int port);
+ void (*port_cleanup)(struct ksz_device *dev, int port);
+ void (*port_setup)(struct ksz_device *dev, int port, bool cpu_port);
+ void (*r_phy)(struct ksz_device *dev, u16 phy, u16 reg, u16 *val);
+ void (*w_phy)(struct ksz_device *dev, u16 phy, u16 reg, u16 val);
+ int (*r_dyn_mac_table)(struct ksz_device *dev, u16 addr, u8 *mac_addr,
+ u8 *fid, u8 *src_port, u8 *timestamp,
+ u16 *entries);
+ int (*r_sta_mac_table)(struct ksz_device *dev, u16 addr,
+ struct alu_struct *alu);
+ void (*w_sta_mac_table)(struct ksz_device *dev, u16 addr,
+ struct alu_struct *alu);
+ void (*r_mib_cnt)(struct ksz_device *dev, int port, u16 addr,
+ u64 *cnt);
+ void (*r_mib_pkt)(struct ksz_device *dev, int port, u16 addr,
+ u64 *dropped, u64 *cnt);
+ void (*freeze_mib)(struct ksz_device *dev, int port, bool freeze);
+ void (*port_init_cnt)(struct ksz_device *dev, int port);
+ int (*shutdown)(struct ksz_device *dev);
+ int (*detect)(struct ksz_device *dev);
+ int (*init)(struct ksz_device *dev);
+ void (*exit)(struct ksz_device *dev);
+};
+
+struct ksz_device *ksz_switch_alloc(struct device *base, void *priv);
+int ksz_switch_register(struct ksz_device *dev,
+ const struct ksz_dev_ops *ops);
+void ksz_switch_remove(struct ksz_device *dev);
+
+int ksz8795_switch_register(struct ksz_device *dev);
+int ksz9477_switch_register(struct ksz_device *dev);
+
+void ksz_update_port_member(struct ksz_device *dev, int port);
+void ksz_init_mib_timer(struct ksz_device *dev);
+
+/* Common DSA access functions */
+
+int ksz_phy_read16(struct dsa_switch *ds, int addr, int reg);
+int ksz_phy_write16(struct dsa_switch *ds, int addr, int reg, u16 val);
+void ksz_adjust_link(struct dsa_switch *ds, int port,
+ struct phy_device *phydev);
+int ksz_sset_count(struct dsa_switch *ds, int port, int sset);
+void ksz_get_ethtool_stats(struct dsa_switch *ds, int port, uint64_t *buf);
+int ksz_port_bridge_join(struct dsa_switch *ds, int port,
+ struct net_device *br);
+void ksz_port_bridge_leave(struct dsa_switch *ds, int port,
+ struct net_device *br);
+void ksz_port_fast_age(struct dsa_switch *ds, int port);
+int ksz_port_vlan_prepare(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan);
+int ksz_port_fdb_dump(struct dsa_switch *ds, int port, dsa_fdb_dump_cb_t *cb,
+ void *data);
+int ksz_port_mdb_prepare(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_mdb *mdb);
+void ksz_port_mdb_add(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_mdb *mdb);
+int ksz_port_mdb_del(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_mdb *mdb);
+int ksz_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy);
+void ksz_disable_port(struct dsa_switch *ds, int port);
+
+/* Common register access functions */
+
+static inline int ksz_read8(struct ksz_device *dev, u32 reg, u8 *val)
+{
+ unsigned int value;
+ int ret = regmap_read(dev->regmap[0], reg, &value);
+
+ *val = value;
+ return ret;
+}
+
+static inline int ksz_read16(struct ksz_device *dev, u32 reg, u16 *val)
+{
+ unsigned int value;
+ int ret = regmap_read(dev->regmap[1], reg, &value);
+
+ *val = value;
+ return ret;
+}
+
+static inline int ksz_read32(struct ksz_device *dev, u32 reg, u32 *val)
+{
+ unsigned int value;
+ int ret = regmap_read(dev->regmap[2], reg, &value);
+
+ *val = value;
+ return ret;
+}
+
+static inline int ksz_read64(struct ksz_device *dev, u32 reg, u64 *val)
+{
+ u32 value[2];
+ int ret;
+
+ ret = regmap_bulk_read(dev->regmap[2], reg, value, 2);
+ if (!ret)
+ *val = (u64)value[0] << 32 | value[1];
+
+ return ret;
+}
+
+static inline int ksz_write8(struct ksz_device *dev, u32 reg, u8 value)
+{
+ return regmap_write(dev->regmap[0], reg, value);
+}
+
+static inline int ksz_write16(struct ksz_device *dev, u32 reg, u16 value)
+{
+ return regmap_write(dev->regmap[1], reg, value);
+}
+
+static inline int ksz_write32(struct ksz_device *dev, u32 reg, u32 value)
+{
+ return regmap_write(dev->regmap[2], reg, value);
+}
+
+static inline int ksz_write64(struct ksz_device *dev, u32 reg, u64 value)
+{
+ u32 val[2];
+
+ /* Ick! ToDo: Add 64bit R/W to regmap on 32bit systems */
+ value = swab64(value);
+ val[0] = swab32(value & 0xffffffffULL);
+ val[1] = swab32(value >> 32ULL);
+
+ return regmap_bulk_write(dev->regmap[2], reg, val, 2);
+}
+
+static inline void ksz_pread8(struct ksz_device *dev, int port, int offset,
+ u8 *data)
+{
+ ksz_read8(dev, dev->dev_ops->get_port_addr(port, offset), data);
+}
+
+static inline void ksz_pread16(struct ksz_device *dev, int port, int offset,
+ u16 *data)
+{
+ ksz_read16(dev, dev->dev_ops->get_port_addr(port, offset), data);
+}
+
+static inline void ksz_pread32(struct ksz_device *dev, int port, int offset,
+ u32 *data)
+{
+ ksz_read32(dev, dev->dev_ops->get_port_addr(port, offset), data);
+}
+
+static inline void ksz_pwrite8(struct ksz_device *dev, int port, int offset,
+ u8 data)
+{
+ ksz_write8(dev, dev->dev_ops->get_port_addr(port, offset), data);
+}
+
+static inline void ksz_pwrite16(struct ksz_device *dev, int port, int offset,
+ u16 data)
+{
+ ksz_write16(dev, dev->dev_ops->get_port_addr(port, offset), data);
+}
+
+static inline void ksz_pwrite32(struct ksz_device *dev, int port, int offset,
+ u32 data)
+{
+ ksz_write32(dev, dev->dev_ops->get_port_addr(port, offset), data);
+}
+
+static inline void ksz_regmap_lock(void *__mtx)
+{
+ struct mutex *mtx = __mtx;
+ mutex_lock(mtx);
+}
+
+static inline void ksz_regmap_unlock(void *__mtx)
+{
+ struct mutex *mtx = __mtx;
+ mutex_unlock(mtx);
+}
+
+/* Regmap tables generation */
+#define KSZ_SPI_OP_RD 3
+#define KSZ_SPI_OP_WR 2
+
+#define swabnot_used(x) 0
+
+#define KSZ_SPI_OP_FLAG_MASK(opcode, swp, regbits, regpad) \
+ swab##swp((opcode) << ((regbits) + (regpad)))
+
+#define KSZ_REGMAP_ENTRY(width, swp, regbits, regpad, regalign) \
+ { \
+ .name = #width, \
+ .val_bits = (width), \
+ .reg_stride = 1, \
+ .reg_bits = (regbits) + (regalign), \
+ .pad_bits = (regpad), \
+ .max_register = BIT(regbits) - 1, \
+ .cache_type = REGCACHE_NONE, \
+ .read_flag_mask = \
+ KSZ_SPI_OP_FLAG_MASK(KSZ_SPI_OP_RD, swp, \
+ regbits, regpad), \
+ .write_flag_mask = \
+ KSZ_SPI_OP_FLAG_MASK(KSZ_SPI_OP_WR, swp, \
+ regbits, regpad), \
+ .lock = ksz_regmap_lock, \
+ .unlock = ksz_regmap_unlock, \
+ .reg_format_endian = REGMAP_ENDIAN_BIG, \
+ .val_format_endian = REGMAP_ENDIAN_BIG \
+ }
+
+#define KSZ_REGMAP_TABLE(ksz, swp, regbits, regpad, regalign) \
+ static const struct regmap_config ksz##_regmap_config[] = { \
+ KSZ_REGMAP_ENTRY(8, swp, (regbits), (regpad), (regalign)), \
+ KSZ_REGMAP_ENTRY(16, swp, (regbits), (regpad), (regalign)), \
+ KSZ_REGMAP_ENTRY(32, swp, (regbits), (regpad), (regalign)), \
+ }
+
+#endif