ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/linux/drivers/pci/controller/dwc/pci-imx6.c b/marvell/linux/drivers/pci/controller/dwc/pci-imx6.c
new file mode 100644
index 0000000..30c259f
--- /dev/null
+++ b/marvell/linux/drivers/pci/controller/dwc/pci-imx6.c
@@ -0,0 +1,1318 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCIe host controller driver for Freescale i.MX6 SoCs
+ *
+ * Copyright (C) 2013 Kosagi
+ * http://www.kosagi.com
+ *
+ * Author: Sean Cross <xobs@kosagi.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/imx6q-iomuxc-gpr.h>
+#include <linux/mfd/syscon/imx7-iomuxc-gpr.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/of_device.h>
+#include <linux/of_address.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/resource.h>
+#include <linux/signal.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/reset.h>
+#include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
+
+#include "pcie-designware.h"
+
+#define IMX8MQ_GPR_PCIE_REF_USE_PAD BIT(9)
+#define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN BIT(10)
+#define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE BIT(11)
+#define IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE GENMASK(11, 8)
+#define IMX8MQ_PCIE2_BASE_ADDR 0x33c00000
+
+#define to_imx6_pcie(x) dev_get_drvdata((x)->dev)
+
+enum imx6_pcie_variants {
+ IMX6Q,
+ IMX6SX,
+ IMX6QP,
+ IMX7D,
+ IMX8MQ,
+};
+
+#define IMX6_PCIE_FLAG_IMX6_PHY BIT(0)
+#define IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE BIT(1)
+#define IMX6_PCIE_FLAG_SUPPORTS_SUSPEND BIT(2)
+
+struct imx6_pcie_drvdata {
+ enum imx6_pcie_variants variant;
+ u32 flags;
+ int dbi_length;
+};
+
+struct imx6_pcie {
+ struct dw_pcie *pci;
+ int reset_gpio;
+ bool gpio_active_high;
+ struct clk *pcie_bus;
+ struct clk *pcie_phy;
+ struct clk *pcie_inbound_axi;
+ struct clk *pcie;
+ struct clk *pcie_aux;
+ struct regmap *iomuxc_gpr;
+ u32 controller_id;
+ struct reset_control *pciephy_reset;
+ struct reset_control *apps_reset;
+ struct reset_control *turnoff_reset;
+ u32 tx_deemph_gen1;
+ u32 tx_deemph_gen2_3p5db;
+ u32 tx_deemph_gen2_6db;
+ u32 tx_swing_full;
+ u32 tx_swing_low;
+ int link_gen;
+ struct regulator *vpcie;
+ void __iomem *phy_base;
+
+ /* power domain for pcie */
+ struct device *pd_pcie;
+ /* power domain for pcie phy */
+ struct device *pd_pcie_phy;
+ const struct imx6_pcie_drvdata *drvdata;
+};
+
+/* Parameters for the waiting for PCIe PHY PLL to lock on i.MX7 */
+#define PHY_PLL_LOCK_WAIT_USLEEP_MAX 200
+#define PHY_PLL_LOCK_WAIT_TIMEOUT (2000 * PHY_PLL_LOCK_WAIT_USLEEP_MAX)
+
+/* PCIe Root Complex registers (memory-mapped) */
+#define PCIE_RC_IMX6_MSI_CAP 0x50
+#define PCIE_RC_LCR 0x7c
+#define PCIE_RC_LCR_MAX_LINK_SPEEDS_GEN1 0x1
+#define PCIE_RC_LCR_MAX_LINK_SPEEDS_GEN2 0x2
+#define PCIE_RC_LCR_MAX_LINK_SPEEDS_MASK 0xf
+
+#define PCIE_RC_LCSR 0x80
+
+/* PCIe Port Logic registers (memory-mapped) */
+#define PL_OFFSET 0x700
+
+#define PCIE_PHY_CTRL (PL_OFFSET + 0x114)
+#define PCIE_PHY_CTRL_DATA(x) FIELD_PREP(GENMASK(15, 0), (x))
+#define PCIE_PHY_CTRL_CAP_ADR BIT(16)
+#define PCIE_PHY_CTRL_CAP_DAT BIT(17)
+#define PCIE_PHY_CTRL_WR BIT(18)
+#define PCIE_PHY_CTRL_RD BIT(19)
+
+#define PCIE_PHY_STAT (PL_OFFSET + 0x110)
+#define PCIE_PHY_STAT_ACK BIT(16)
+
+#define PCIE_LINK_WIDTH_SPEED_CONTROL 0x80C
+
+/* PHY registers (not memory-mapped) */
+#define PCIE_PHY_ATEOVRD 0x10
+#define PCIE_PHY_ATEOVRD_EN BIT(2)
+#define PCIE_PHY_ATEOVRD_REF_CLKDIV_SHIFT 0
+#define PCIE_PHY_ATEOVRD_REF_CLKDIV_MASK 0x1
+
+#define PCIE_PHY_MPLL_OVRD_IN_LO 0x11
+#define PCIE_PHY_MPLL_MULTIPLIER_SHIFT 2
+#define PCIE_PHY_MPLL_MULTIPLIER_MASK 0x7f
+#define PCIE_PHY_MPLL_MULTIPLIER_OVRD BIT(9)
+
+#define PCIE_PHY_RX_ASIC_OUT 0x100D
+#define PCIE_PHY_RX_ASIC_OUT_VALID (1 << 0)
+
+/* iMX7 PCIe PHY registers */
+#define PCIE_PHY_CMN_REG4 0x14
+/* These are probably the bits that *aren't* DCC_FB_EN */
+#define PCIE_PHY_CMN_REG4_DCC_FB_EN 0x29
+
+#define PCIE_PHY_CMN_REG15 0x54
+#define PCIE_PHY_CMN_REG15_DLY_4 BIT(2)
+#define PCIE_PHY_CMN_REG15_PLL_PD BIT(5)
+#define PCIE_PHY_CMN_REG15_OVRD_PLL_PD BIT(7)
+
+#define PCIE_PHY_CMN_REG24 0x90
+#define PCIE_PHY_CMN_REG24_RX_EQ BIT(6)
+#define PCIE_PHY_CMN_REG24_RX_EQ_SEL BIT(3)
+
+#define PCIE_PHY_CMN_REG26 0x98
+#define PCIE_PHY_CMN_REG26_ATT_MODE 0xBC
+
+#define PHY_RX_OVRD_IN_LO 0x1005
+#define PHY_RX_OVRD_IN_LO_RX_DATA_EN BIT(5)
+#define PHY_RX_OVRD_IN_LO_RX_PLL_EN BIT(3)
+
+static int pcie_phy_poll_ack(struct imx6_pcie *imx6_pcie, bool exp_val)
+{
+ struct dw_pcie *pci = imx6_pcie->pci;
+ bool val;
+ u32 max_iterations = 10;
+ u32 wait_counter = 0;
+
+ do {
+ val = dw_pcie_readl_dbi(pci, PCIE_PHY_STAT) &
+ PCIE_PHY_STAT_ACK;
+ wait_counter++;
+
+ if (val == exp_val)
+ return 0;
+
+ udelay(1);
+ } while (wait_counter < max_iterations);
+
+ return -ETIMEDOUT;
+}
+
+static int pcie_phy_wait_ack(struct imx6_pcie *imx6_pcie, int addr)
+{
+ struct dw_pcie *pci = imx6_pcie->pci;
+ u32 val;
+ int ret;
+
+ val = PCIE_PHY_CTRL_DATA(addr);
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, val);
+
+ val |= PCIE_PHY_CTRL_CAP_ADR;
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, val);
+
+ ret = pcie_phy_poll_ack(imx6_pcie, true);
+ if (ret)
+ return ret;
+
+ val = PCIE_PHY_CTRL_DATA(addr);
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, val);
+
+ return pcie_phy_poll_ack(imx6_pcie, false);
+}
+
+/* Read from the 16-bit PCIe PHY control registers (not memory-mapped) */
+static int pcie_phy_read(struct imx6_pcie *imx6_pcie, int addr, u16 *data)
+{
+ struct dw_pcie *pci = imx6_pcie->pci;
+ u32 phy_ctl;
+ int ret;
+
+ ret = pcie_phy_wait_ack(imx6_pcie, addr);
+ if (ret)
+ return ret;
+
+ /* assert Read signal */
+ phy_ctl = PCIE_PHY_CTRL_RD;
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, phy_ctl);
+
+ ret = pcie_phy_poll_ack(imx6_pcie, true);
+ if (ret)
+ return ret;
+
+ *data = dw_pcie_readl_dbi(pci, PCIE_PHY_STAT);
+
+ /* deassert Read signal */
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, 0x00);
+
+ return pcie_phy_poll_ack(imx6_pcie, false);
+}
+
+static int pcie_phy_write(struct imx6_pcie *imx6_pcie, int addr, u16 data)
+{
+ struct dw_pcie *pci = imx6_pcie->pci;
+ u32 var;
+ int ret;
+
+ /* write addr */
+ /* cap addr */
+ ret = pcie_phy_wait_ack(imx6_pcie, addr);
+ if (ret)
+ return ret;
+
+ var = PCIE_PHY_CTRL_DATA(data);
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, var);
+
+ /* capture data */
+ var |= PCIE_PHY_CTRL_CAP_DAT;
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, var);
+
+ ret = pcie_phy_poll_ack(imx6_pcie, true);
+ if (ret)
+ return ret;
+
+ /* deassert cap data */
+ var = PCIE_PHY_CTRL_DATA(data);
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, var);
+
+ /* wait for ack de-assertion */
+ ret = pcie_phy_poll_ack(imx6_pcie, false);
+ if (ret)
+ return ret;
+
+ /* assert wr signal */
+ var = PCIE_PHY_CTRL_WR;
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, var);
+
+ /* wait for ack */
+ ret = pcie_phy_poll_ack(imx6_pcie, true);
+ if (ret)
+ return ret;
+
+ /* deassert wr signal */
+ var = PCIE_PHY_CTRL_DATA(data);
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, var);
+
+ /* wait for ack de-assertion */
+ ret = pcie_phy_poll_ack(imx6_pcie, false);
+ if (ret)
+ return ret;
+
+ dw_pcie_writel_dbi(pci, PCIE_PHY_CTRL, 0x0);
+
+ return 0;
+}
+
+static void imx6_pcie_reset_phy(struct imx6_pcie *imx6_pcie)
+{
+ u16 tmp;
+
+ if (!(imx6_pcie->drvdata->flags & IMX6_PCIE_FLAG_IMX6_PHY))
+ return;
+
+ pcie_phy_read(imx6_pcie, PHY_RX_OVRD_IN_LO, &tmp);
+ tmp |= (PHY_RX_OVRD_IN_LO_RX_DATA_EN |
+ PHY_RX_OVRD_IN_LO_RX_PLL_EN);
+ pcie_phy_write(imx6_pcie, PHY_RX_OVRD_IN_LO, tmp);
+
+ usleep_range(2000, 3000);
+
+ pcie_phy_read(imx6_pcie, PHY_RX_OVRD_IN_LO, &tmp);
+ tmp &= ~(PHY_RX_OVRD_IN_LO_RX_DATA_EN |
+ PHY_RX_OVRD_IN_LO_RX_PLL_EN);
+ pcie_phy_write(imx6_pcie, PHY_RX_OVRD_IN_LO, tmp);
+}
+
+#ifdef CONFIG_ARM
+/* Added for PCI abort handling */
+static int imx6q_pcie_abort_handler(unsigned long addr,
+ unsigned int fsr, struct pt_regs *regs)
+{
+ unsigned long pc = instruction_pointer(regs);
+ unsigned long instr = *(unsigned long *)pc;
+ int reg = (instr >> 12) & 15;
+
+ /*
+ * If the instruction being executed was a read,
+ * make it look like it read all-ones.
+ */
+ if ((instr & 0x0c100000) == 0x04100000) {
+ unsigned long val;
+
+ if (instr & 0x00400000)
+ val = 255;
+ else
+ val = -1;
+
+ regs->uregs[reg] = val;
+ regs->ARM_pc += 4;
+ return 0;
+ }
+
+ if ((instr & 0x0e100090) == 0x00100090) {
+ regs->uregs[reg] = -1;
+ regs->ARM_pc += 4;
+ return 0;
+ }
+
+ return 1;
+}
+#endif
+
+static int imx6_pcie_attach_pd(struct device *dev)
+{
+ struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev);
+ struct device_link *link;
+
+ /* Do nothing when in a single power domain */
+ if (dev->pm_domain)
+ return 0;
+
+ imx6_pcie->pd_pcie = dev_pm_domain_attach_by_name(dev, "pcie");
+ if (IS_ERR(imx6_pcie->pd_pcie))
+ return PTR_ERR(imx6_pcie->pd_pcie);
+ /* Do nothing when power domain missing */
+ if (!imx6_pcie->pd_pcie)
+ return 0;
+ link = device_link_add(dev, imx6_pcie->pd_pcie,
+ DL_FLAG_STATELESS |
+ DL_FLAG_PM_RUNTIME |
+ DL_FLAG_RPM_ACTIVE);
+ if (!link) {
+ dev_err(dev, "Failed to add device_link to pcie pd.\n");
+ return -EINVAL;
+ }
+
+ imx6_pcie->pd_pcie_phy = dev_pm_domain_attach_by_name(dev, "pcie_phy");
+ if (IS_ERR(imx6_pcie->pd_pcie_phy))
+ return PTR_ERR(imx6_pcie->pd_pcie_phy);
+
+ link = device_link_add(dev, imx6_pcie->pd_pcie_phy,
+ DL_FLAG_STATELESS |
+ DL_FLAG_PM_RUNTIME |
+ DL_FLAG_RPM_ACTIVE);
+ if (!link) {
+ dev_err(dev, "Failed to add device_link to pcie_phy pd.\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie)
+{
+ struct device *dev = imx6_pcie->pci->dev;
+
+ switch (imx6_pcie->drvdata->variant) {
+ case IMX7D:
+ case IMX8MQ:
+ reset_control_assert(imx6_pcie->pciephy_reset);
+ reset_control_assert(imx6_pcie->apps_reset);
+ break;
+ case IMX6SX:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6SX_GPR12_PCIE_TEST_POWERDOWN,
+ IMX6SX_GPR12_PCIE_TEST_POWERDOWN);
+ /* Force PCIe PHY reset */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR5,
+ IMX6SX_GPR5_PCIE_BTNRST_RESET,
+ IMX6SX_GPR5_PCIE_BTNRST_RESET);
+ break;
+ case IMX6QP:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_SW_RST,
+ IMX6Q_GPR1_PCIE_SW_RST);
+ break;
+ case IMX6Q:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_TEST_PD, 1 << 18);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_REF_CLK_EN, 0 << 16);
+ break;
+ }
+
+ if (imx6_pcie->vpcie && regulator_is_enabled(imx6_pcie->vpcie) > 0) {
+ int ret = regulator_disable(imx6_pcie->vpcie);
+
+ if (ret)
+ dev_err(dev, "failed to disable vpcie regulator: %d\n",
+ ret);
+ }
+
+ /* Some boards don't have PCIe reset GPIO. */
+ if (gpio_is_valid(imx6_pcie->reset_gpio))
+ gpio_set_value_cansleep(imx6_pcie->reset_gpio,
+ imx6_pcie->gpio_active_high);
+}
+
+static unsigned int imx6_pcie_grp_offset(const struct imx6_pcie *imx6_pcie)
+{
+ WARN_ON(imx6_pcie->drvdata->variant != IMX8MQ);
+ return imx6_pcie->controller_id == 1 ? IOMUXC_GPR16 : IOMUXC_GPR14;
+}
+
+static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
+{
+ struct dw_pcie *pci = imx6_pcie->pci;
+ struct device *dev = pci->dev;
+ unsigned int offset;
+ int ret = 0;
+
+ switch (imx6_pcie->drvdata->variant) {
+ case IMX6SX:
+ ret = clk_prepare_enable(imx6_pcie->pcie_inbound_axi);
+ if (ret) {
+ dev_err(dev, "unable to enable pcie_axi clock\n");
+ break;
+ }
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6SX_GPR12_PCIE_TEST_POWERDOWN, 0);
+ break;
+ case IMX6QP: /* FALLTHROUGH */
+ case IMX6Q:
+ /* power up core phy and enable ref clock */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_TEST_PD, 0 << 18);
+ /*
+ * the async reset input need ref clock to sync internally,
+ * when the ref clock comes after reset, internal synced
+ * reset time is too short, cannot meet the requirement.
+ * add one ~10us delay here.
+ */
+ usleep_range(10, 100);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_REF_CLK_EN, 1 << 16);
+ break;
+ case IMX7D:
+ break;
+ case IMX8MQ:
+ ret = clk_prepare_enable(imx6_pcie->pcie_aux);
+ if (ret) {
+ dev_err(dev, "unable to enable pcie_aux clock\n");
+ break;
+ }
+
+ offset = imx6_pcie_grp_offset(imx6_pcie);
+ /*
+ * Set the over ride low and enabled
+ * make sure that REF_CLK is turned on.
+ */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, offset,
+ IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE,
+ 0);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, offset,
+ IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN,
+ IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN);
+ break;
+ }
+
+ return ret;
+}
+
+static void imx7d_pcie_wait_for_phy_pll_lock(struct imx6_pcie *imx6_pcie)
+{
+ u32 val;
+ struct device *dev = imx6_pcie->pci->dev;
+
+ if (regmap_read_poll_timeout(imx6_pcie->iomuxc_gpr,
+ IOMUXC_GPR22, val,
+ val & IMX7D_GPR22_PCIE_PHY_PLL_LOCKED,
+ PHY_PLL_LOCK_WAIT_USLEEP_MAX,
+ PHY_PLL_LOCK_WAIT_TIMEOUT))
+ dev_err(dev, "PCIe PLL lock timeout\n");
+}
+
+static void imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie)
+{
+ struct dw_pcie *pci = imx6_pcie->pci;
+ struct device *dev = pci->dev;
+ int ret;
+
+ if (imx6_pcie->vpcie && !regulator_is_enabled(imx6_pcie->vpcie)) {
+ ret = regulator_enable(imx6_pcie->vpcie);
+ if (ret) {
+ dev_err(dev, "failed to enable vpcie regulator: %d\n",
+ ret);
+ return;
+ }
+ }
+
+ ret = clk_prepare_enable(imx6_pcie->pcie_phy);
+ if (ret) {
+ dev_err(dev, "unable to enable pcie_phy clock\n");
+ goto err_pcie_phy;
+ }
+
+ ret = clk_prepare_enable(imx6_pcie->pcie_bus);
+ if (ret) {
+ dev_err(dev, "unable to enable pcie_bus clock\n");
+ goto err_pcie_bus;
+ }
+
+ ret = clk_prepare_enable(imx6_pcie->pcie);
+ if (ret) {
+ dev_err(dev, "unable to enable pcie clock\n");
+ goto err_pcie;
+ }
+
+ ret = imx6_pcie_enable_ref_clk(imx6_pcie);
+ if (ret) {
+ dev_err(dev, "unable to enable pcie ref clock\n");
+ goto err_ref_clk;
+ }
+
+ /* allow the clocks to stabilize */
+ usleep_range(200, 500);
+
+ switch (imx6_pcie->drvdata->variant) {
+ case IMX8MQ:
+ reset_control_deassert(imx6_pcie->pciephy_reset);
+ break;
+ case IMX7D:
+ reset_control_deassert(imx6_pcie->pciephy_reset);
+
+ /* Workaround for ERR010728, failure of PCI-e PLL VCO to
+ * oscillate, especially when cold. This turns off "Duty-cycle
+ * Corrector" and other mysterious undocumented things.
+ */
+ if (likely(imx6_pcie->phy_base)) {
+ /* De-assert DCC_FB_EN */
+ writel(PCIE_PHY_CMN_REG4_DCC_FB_EN,
+ imx6_pcie->phy_base + PCIE_PHY_CMN_REG4);
+ /* Assert RX_EQS and RX_EQS_SEL */
+ writel(PCIE_PHY_CMN_REG24_RX_EQ_SEL
+ | PCIE_PHY_CMN_REG24_RX_EQ,
+ imx6_pcie->phy_base + PCIE_PHY_CMN_REG24);
+ /* Assert ATT_MODE */
+ writel(PCIE_PHY_CMN_REG26_ATT_MODE,
+ imx6_pcie->phy_base + PCIE_PHY_CMN_REG26);
+ } else {
+ dev_warn(dev, "Unable to apply ERR010728 workaround. DT missing fsl,imx7d-pcie-phy phandle ?\n");
+ }
+
+ imx7d_pcie_wait_for_phy_pll_lock(imx6_pcie);
+ break;
+ case IMX6SX:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR5,
+ IMX6SX_GPR5_PCIE_BTNRST_RESET, 0);
+ break;
+ case IMX6QP:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_SW_RST, 0);
+
+ usleep_range(200, 500);
+ break;
+ case IMX6Q: /* Nothing to do */
+ break;
+ }
+
+ /* Some boards don't have PCIe reset GPIO. */
+ if (gpio_is_valid(imx6_pcie->reset_gpio)) {
+ msleep(100);
+ gpio_set_value_cansleep(imx6_pcie->reset_gpio,
+ !imx6_pcie->gpio_active_high);
+ /* Wait for 100ms after PERST# deassertion (PCIe r5.0, 6.6.1) */
+ msleep(100);
+ }
+
+ return;
+
+err_ref_clk:
+ clk_disable_unprepare(imx6_pcie->pcie);
+err_pcie:
+ clk_disable_unprepare(imx6_pcie->pcie_bus);
+err_pcie_bus:
+ clk_disable_unprepare(imx6_pcie->pcie_phy);
+err_pcie_phy:
+ if (imx6_pcie->vpcie && regulator_is_enabled(imx6_pcie->vpcie) > 0) {
+ ret = regulator_disable(imx6_pcie->vpcie);
+ if (ret)
+ dev_err(dev, "failed to disable vpcie regulator: %d\n",
+ ret);
+ }
+}
+
+static void imx6_pcie_configure_type(struct imx6_pcie *imx6_pcie)
+{
+ unsigned int mask, val;
+
+ if (imx6_pcie->drvdata->variant == IMX8MQ &&
+ imx6_pcie->controller_id == 1) {
+ mask = IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE;
+ val = FIELD_PREP(IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE,
+ PCI_EXP_TYPE_ROOT_PORT);
+ } else {
+ mask = IMX6Q_GPR12_DEVICE_TYPE;
+ val = FIELD_PREP(IMX6Q_GPR12_DEVICE_TYPE,
+ PCI_EXP_TYPE_ROOT_PORT);
+ }
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, mask, val);
+}
+
+static void imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie)
+{
+ switch (imx6_pcie->drvdata->variant) {
+ case IMX8MQ:
+ /*
+ * TODO: Currently this code assumes external
+ * oscillator is being used
+ */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr,
+ imx6_pcie_grp_offset(imx6_pcie),
+ IMX8MQ_GPR_PCIE_REF_USE_PAD,
+ IMX8MQ_GPR_PCIE_REF_USE_PAD);
+ break;
+ case IMX7D:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX7D_GPR12_PCIE_PHY_REFCLK_SEL, 0);
+ break;
+ case IMX6SX:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6SX_GPR12_PCIE_RX_EQ_MASK,
+ IMX6SX_GPR12_PCIE_RX_EQ_2);
+ /* FALLTHROUGH */
+ default:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
+
+ /* configure constant input signal to the pcie ctrl and phy */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_LOS_LEVEL, 9 << 4);
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_DEEMPH_GEN1,
+ imx6_pcie->tx_deemph_gen1 << 0);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_DEEMPH_GEN2_3P5DB,
+ imx6_pcie->tx_deemph_gen2_3p5db << 6);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_DEEMPH_GEN2_6DB,
+ imx6_pcie->tx_deemph_gen2_6db << 12);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_SWING_FULL,
+ imx6_pcie->tx_swing_full << 18);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_SWING_LOW,
+ imx6_pcie->tx_swing_low << 25);
+ break;
+ }
+
+ imx6_pcie_configure_type(imx6_pcie);
+}
+
+static int imx6_setup_phy_mpll(struct imx6_pcie *imx6_pcie)
+{
+ unsigned long phy_rate = clk_get_rate(imx6_pcie->pcie_phy);
+ int mult, div;
+ u16 val;
+
+ if (!(imx6_pcie->drvdata->flags & IMX6_PCIE_FLAG_IMX6_PHY))
+ return 0;
+
+ switch (phy_rate) {
+ case 125000000:
+ /*
+ * The default settings of the MPLL are for a 125MHz input
+ * clock, so no need to reconfigure anything in that case.
+ */
+ return 0;
+ case 100000000:
+ mult = 25;
+ div = 0;
+ break;
+ case 200000000:
+ mult = 25;
+ div = 1;
+ break;
+ default:
+ dev_err(imx6_pcie->pci->dev,
+ "Unsupported PHY reference clock rate %lu\n", phy_rate);
+ return -EINVAL;
+ }
+
+ pcie_phy_read(imx6_pcie, PCIE_PHY_MPLL_OVRD_IN_LO, &val);
+ val &= ~(PCIE_PHY_MPLL_MULTIPLIER_MASK <<
+ PCIE_PHY_MPLL_MULTIPLIER_SHIFT);
+ val |= mult << PCIE_PHY_MPLL_MULTIPLIER_SHIFT;
+ val |= PCIE_PHY_MPLL_MULTIPLIER_OVRD;
+ pcie_phy_write(imx6_pcie, PCIE_PHY_MPLL_OVRD_IN_LO, val);
+
+ pcie_phy_read(imx6_pcie, PCIE_PHY_ATEOVRD, &val);
+ val &= ~(PCIE_PHY_ATEOVRD_REF_CLKDIV_MASK <<
+ PCIE_PHY_ATEOVRD_REF_CLKDIV_SHIFT);
+ val |= div << PCIE_PHY_ATEOVRD_REF_CLKDIV_SHIFT;
+ val |= PCIE_PHY_ATEOVRD_EN;
+ pcie_phy_write(imx6_pcie, PCIE_PHY_ATEOVRD, val);
+
+ return 0;
+}
+
+static int imx6_pcie_wait_for_speed_change(struct imx6_pcie *imx6_pcie)
+{
+ struct dw_pcie *pci = imx6_pcie->pci;
+ struct device *dev = pci->dev;
+ u32 tmp;
+ unsigned int retries;
+
+ for (retries = 0; retries < 200; retries++) {
+ tmp = dw_pcie_readl_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL);
+ /* Test if the speed change finished. */
+ if (!(tmp & PORT_LOGIC_SPEED_CHANGE))
+ return 0;
+ usleep_range(100, 1000);
+ }
+
+ dev_err(dev, "Speed change timeout\n");
+ return -ETIMEDOUT;
+}
+
+static void imx6_pcie_ltssm_enable(struct device *dev)
+{
+ struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev);
+
+ switch (imx6_pcie->drvdata->variant) {
+ case IMX6Q:
+ case IMX6SX:
+ case IMX6QP:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_PCIE_CTL_2,
+ IMX6Q_GPR12_PCIE_CTL_2);
+ break;
+ case IMX7D:
+ case IMX8MQ:
+ reset_control_deassert(imx6_pcie->apps_reset);
+ break;
+ }
+}
+
+static int imx6_pcie_establish_link(struct imx6_pcie *imx6_pcie)
+{
+ struct dw_pcie *pci = imx6_pcie->pci;
+ struct device *dev = pci->dev;
+ u32 tmp;
+ int ret;
+
+ /*
+ * Force Gen1 operation when starting the link. In case the link is
+ * started in Gen2 mode, there is a possibility the devices on the
+ * bus will not be detected at all. This happens with PCIe switches.
+ */
+ tmp = dw_pcie_readl_dbi(pci, PCIE_RC_LCR);
+ tmp &= ~PCIE_RC_LCR_MAX_LINK_SPEEDS_MASK;
+ tmp |= PCIE_RC_LCR_MAX_LINK_SPEEDS_GEN1;
+ dw_pcie_writel_dbi(pci, PCIE_RC_LCR, tmp);
+
+ /* Start LTSSM. */
+ imx6_pcie_ltssm_enable(dev);
+
+ ret = dw_pcie_wait_for_link(pci);
+ if (ret)
+ goto err_reset_phy;
+
+ if (imx6_pcie->link_gen == 2) {
+ /* Allow Gen2 mode after the link is up. */
+ tmp = dw_pcie_readl_dbi(pci, PCIE_RC_LCR);
+ tmp &= ~PCIE_RC_LCR_MAX_LINK_SPEEDS_MASK;
+ tmp |= PCIE_RC_LCR_MAX_LINK_SPEEDS_GEN2;
+ dw_pcie_writel_dbi(pci, PCIE_RC_LCR, tmp);
+
+ /*
+ * Start Directed Speed Change so the best possible
+ * speed both link partners support can be negotiated.
+ */
+ tmp = dw_pcie_readl_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL);
+ tmp |= PORT_LOGIC_SPEED_CHANGE;
+ dw_pcie_writel_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL, tmp);
+
+ if (imx6_pcie->drvdata->flags &
+ IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE) {
+ /*
+ * On i.MX7, DIRECT_SPEED_CHANGE behaves differently
+ * from i.MX6 family when no link speed transition
+ * occurs and we go Gen1 -> yep, Gen1. The difference
+ * is that, in such case, it will not be cleared by HW
+ * which will cause the following code to report false
+ * failure.
+ */
+
+ ret = imx6_pcie_wait_for_speed_change(imx6_pcie);
+ if (ret) {
+ dev_err(dev, "Failed to bring link up!\n");
+ goto err_reset_phy;
+ }
+ }
+
+ /* Make sure link training is finished as well! */
+ ret = dw_pcie_wait_for_link(pci);
+ if (ret) {
+ dev_err(dev, "Failed to bring link up!\n");
+ goto err_reset_phy;
+ }
+ } else {
+ dev_info(dev, "Link: Gen2 disabled\n");
+ }
+
+ tmp = dw_pcie_readl_dbi(pci, PCIE_RC_LCSR);
+ dev_info(dev, "Link up, Gen%i\n", (tmp >> 16) & 0xf);
+ return 0;
+
+err_reset_phy:
+ dev_dbg(dev, "PHY DEBUG_R0=0x%08x DEBUG_R1=0x%08x\n",
+ dw_pcie_readl_dbi(pci, PCIE_PORT_DEBUG0),
+ dw_pcie_readl_dbi(pci, PCIE_PORT_DEBUG1));
+ imx6_pcie_reset_phy(imx6_pcie);
+ return ret;
+}
+
+static int imx6_pcie_host_init(struct pcie_port *pp)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ struct imx6_pcie *imx6_pcie = to_imx6_pcie(pci);
+
+ imx6_pcie_assert_core_reset(imx6_pcie);
+ imx6_pcie_init_phy(imx6_pcie);
+ imx6_pcie_deassert_core_reset(imx6_pcie);
+ imx6_setup_phy_mpll(imx6_pcie);
+ dw_pcie_setup_rc(pp);
+ imx6_pcie_establish_link(imx6_pcie);
+
+ if (IS_ENABLED(CONFIG_PCI_MSI))
+ dw_pcie_msi_init(pp);
+
+ return 0;
+}
+
+static const struct dw_pcie_host_ops imx6_pcie_host_ops = {
+ .host_init = imx6_pcie_host_init,
+};
+
+static int imx6_add_pcie_port(struct imx6_pcie *imx6_pcie,
+ struct platform_device *pdev)
+{
+ struct dw_pcie *pci = imx6_pcie->pci;
+ struct pcie_port *pp = &pci->pp;
+ struct device *dev = &pdev->dev;
+ int ret;
+
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+ pp->msi_irq = platform_get_irq_byname(pdev, "msi");
+ if (pp->msi_irq <= 0) {
+ dev_err(dev, "failed to get MSI irq\n");
+ return -ENODEV;
+ }
+ }
+
+ pp->ops = &imx6_pcie_host_ops;
+
+ ret = dw_pcie_host_init(pp);
+ if (ret) {
+ dev_err(dev, "failed to initialize host\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+ /* No special ops needed, but pcie-designware still expects this struct */
+};
+
+#ifdef CONFIG_PM_SLEEP
+static void imx6_pcie_ltssm_disable(struct device *dev)
+{
+ struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev);
+
+ switch (imx6_pcie->drvdata->variant) {
+ case IMX6SX:
+ case IMX6QP:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_PCIE_CTL_2, 0);
+ break;
+ case IMX7D:
+ reset_control_assert(imx6_pcie->apps_reset);
+ break;
+ default:
+ dev_err(dev, "ltssm_disable not supported\n");
+ }
+}
+
+static void imx6_pcie_pm_turnoff(struct imx6_pcie *imx6_pcie)
+{
+ struct device *dev = imx6_pcie->pci->dev;
+
+ /* Some variants have a turnoff reset in DT */
+ if (imx6_pcie->turnoff_reset) {
+ reset_control_assert(imx6_pcie->turnoff_reset);
+ reset_control_deassert(imx6_pcie->turnoff_reset);
+ goto pm_turnoff_sleep;
+ }
+
+ /* Others poke directly at IOMUXC registers */
+ switch (imx6_pcie->drvdata->variant) {
+ case IMX6SX:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6SX_GPR12_PCIE_PM_TURN_OFF,
+ IMX6SX_GPR12_PCIE_PM_TURN_OFF);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6SX_GPR12_PCIE_PM_TURN_OFF, 0);
+ break;
+ default:
+ dev_err(dev, "PME_Turn_Off not implemented\n");
+ return;
+ }
+
+ /*
+ * Components with an upstream port must respond to
+ * PME_Turn_Off with PME_TO_Ack but we can't check.
+ *
+ * The standard recommends a 1-10ms timeout after which to
+ * proceed anyway as if acks were received.
+ */
+pm_turnoff_sleep:
+ usleep_range(1000, 10000);
+}
+
+static void imx6_pcie_clk_disable(struct imx6_pcie *imx6_pcie)
+{
+ clk_disable_unprepare(imx6_pcie->pcie);
+ clk_disable_unprepare(imx6_pcie->pcie_phy);
+ clk_disable_unprepare(imx6_pcie->pcie_bus);
+
+ switch (imx6_pcie->drvdata->variant) {
+ case IMX6SX:
+ clk_disable_unprepare(imx6_pcie->pcie_inbound_axi);
+ break;
+ case IMX7D:
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX7D_GPR12_PCIE_PHY_REFCLK_SEL,
+ IMX7D_GPR12_PCIE_PHY_REFCLK_SEL);
+ break;
+ case IMX8MQ:
+ clk_disable_unprepare(imx6_pcie->pcie_aux);
+ break;
+ default:
+ break;
+ }
+}
+
+static int imx6_pcie_suspend_noirq(struct device *dev)
+{
+ struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev);
+
+ if (!(imx6_pcie->drvdata->flags & IMX6_PCIE_FLAG_SUPPORTS_SUSPEND))
+ return 0;
+
+ imx6_pcie_pm_turnoff(imx6_pcie);
+ imx6_pcie_clk_disable(imx6_pcie);
+ imx6_pcie_ltssm_disable(dev);
+
+ return 0;
+}
+
+static int imx6_pcie_resume_noirq(struct device *dev)
+{
+ int ret;
+ struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev);
+ struct pcie_port *pp = &imx6_pcie->pci->pp;
+
+ if (!(imx6_pcie->drvdata->flags & IMX6_PCIE_FLAG_SUPPORTS_SUSPEND))
+ return 0;
+
+ imx6_pcie_assert_core_reset(imx6_pcie);
+ imx6_pcie_init_phy(imx6_pcie);
+ imx6_pcie_deassert_core_reset(imx6_pcie);
+ dw_pcie_setup_rc(pp);
+
+ ret = imx6_pcie_establish_link(imx6_pcie);
+ if (ret < 0)
+ dev_info(dev, "pcie link is down after resume.\n");
+
+ return 0;
+}
+#endif
+
+static const struct dev_pm_ops imx6_pcie_pm_ops = {
+ SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(imx6_pcie_suspend_noirq,
+ imx6_pcie_resume_noirq)
+};
+
+static int imx6_pcie_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct dw_pcie *pci;
+ struct imx6_pcie *imx6_pcie;
+ struct device_node *np;
+ struct resource *dbi_base;
+ struct device_node *node = dev->of_node;
+ int ret;
+ u16 val;
+
+ imx6_pcie = devm_kzalloc(dev, sizeof(*imx6_pcie), GFP_KERNEL);
+ if (!imx6_pcie)
+ return -ENOMEM;
+
+ pci = devm_kzalloc(dev, sizeof(*pci), GFP_KERNEL);
+ if (!pci)
+ return -ENOMEM;
+
+ pci->dev = dev;
+ pci->ops = &dw_pcie_ops;
+
+ imx6_pcie->pci = pci;
+ imx6_pcie->drvdata = of_device_get_match_data(dev);
+
+ /* Find the PHY if one is defined, only imx7d uses it */
+ np = of_parse_phandle(node, "fsl,imx7d-pcie-phy", 0);
+ if (np) {
+ struct resource res;
+
+ ret = of_address_to_resource(np, 0, &res);
+ if (ret) {
+ dev_err(dev, "Unable to map PCIe PHY\n");
+ return ret;
+ }
+ imx6_pcie->phy_base = devm_ioremap_resource(dev, &res);
+ if (IS_ERR(imx6_pcie->phy_base)) {
+ dev_err(dev, "Unable to map PCIe PHY\n");
+ return PTR_ERR(imx6_pcie->phy_base);
+ }
+ }
+
+ dbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ pci->dbi_base = devm_ioremap_resource(dev, dbi_base);
+ if (IS_ERR(pci->dbi_base))
+ return PTR_ERR(pci->dbi_base);
+
+ /* Fetch GPIOs */
+ imx6_pcie->reset_gpio = of_get_named_gpio(node, "reset-gpio", 0);
+ imx6_pcie->gpio_active_high = of_property_read_bool(node,
+ "reset-gpio-active-high");
+ if (gpio_is_valid(imx6_pcie->reset_gpio)) {
+ ret = devm_gpio_request_one(dev, imx6_pcie->reset_gpio,
+ imx6_pcie->gpio_active_high ?
+ GPIOF_OUT_INIT_HIGH :
+ GPIOF_OUT_INIT_LOW,
+ "PCIe reset");
+ if (ret) {
+ dev_err(dev, "unable to get reset gpio\n");
+ return ret;
+ }
+ } else if (imx6_pcie->reset_gpio == -EPROBE_DEFER) {
+ return imx6_pcie->reset_gpio;
+ }
+
+ /* Fetch clocks */
+ imx6_pcie->pcie_phy = devm_clk_get(dev, "pcie_phy");
+ if (IS_ERR(imx6_pcie->pcie_phy)) {
+ dev_err(dev, "pcie_phy clock source missing or invalid\n");
+ return PTR_ERR(imx6_pcie->pcie_phy);
+ }
+
+ imx6_pcie->pcie_bus = devm_clk_get(dev, "pcie_bus");
+ if (IS_ERR(imx6_pcie->pcie_bus)) {
+ dev_err(dev, "pcie_bus clock source missing or invalid\n");
+ return PTR_ERR(imx6_pcie->pcie_bus);
+ }
+
+ imx6_pcie->pcie = devm_clk_get(dev, "pcie");
+ if (IS_ERR(imx6_pcie->pcie)) {
+ dev_err(dev, "pcie clock source missing or invalid\n");
+ return PTR_ERR(imx6_pcie->pcie);
+ }
+
+ switch (imx6_pcie->drvdata->variant) {
+ case IMX6SX:
+ imx6_pcie->pcie_inbound_axi = devm_clk_get(dev,
+ "pcie_inbound_axi");
+ if (IS_ERR(imx6_pcie->pcie_inbound_axi)) {
+ dev_err(dev, "pcie_inbound_axi clock missing or invalid\n");
+ return PTR_ERR(imx6_pcie->pcie_inbound_axi);
+ }
+ break;
+ case IMX8MQ:
+ imx6_pcie->pcie_aux = devm_clk_get(dev, "pcie_aux");
+ if (IS_ERR(imx6_pcie->pcie_aux)) {
+ dev_err(dev, "pcie_aux clock source missing or invalid\n");
+ return PTR_ERR(imx6_pcie->pcie_aux);
+ }
+ /* fall through */
+ case IMX7D:
+ if (dbi_base->start == IMX8MQ_PCIE2_BASE_ADDR)
+ imx6_pcie->controller_id = 1;
+
+ imx6_pcie->pciephy_reset = devm_reset_control_get_exclusive(dev,
+ "pciephy");
+ if (IS_ERR(imx6_pcie->pciephy_reset)) {
+ dev_err(dev, "Failed to get PCIEPHY reset control\n");
+ return PTR_ERR(imx6_pcie->pciephy_reset);
+ }
+
+ imx6_pcie->apps_reset = devm_reset_control_get_exclusive(dev,
+ "apps");
+ if (IS_ERR(imx6_pcie->apps_reset)) {
+ dev_err(dev, "Failed to get PCIE APPS reset control\n");
+ return PTR_ERR(imx6_pcie->apps_reset);
+ }
+ break;
+ default:
+ break;
+ }
+
+ /* Grab turnoff reset */
+ imx6_pcie->turnoff_reset = devm_reset_control_get_optional_exclusive(dev, "turnoff");
+ if (IS_ERR(imx6_pcie->turnoff_reset)) {
+ dev_err(dev, "Failed to get TURNOFF reset control\n");
+ return PTR_ERR(imx6_pcie->turnoff_reset);
+ }
+
+ /* Grab GPR config register range */
+ imx6_pcie->iomuxc_gpr =
+ syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
+ if (IS_ERR(imx6_pcie->iomuxc_gpr)) {
+ dev_err(dev, "unable to find iomuxc registers\n");
+ return PTR_ERR(imx6_pcie->iomuxc_gpr);
+ }
+
+ /* Grab PCIe PHY Tx Settings */
+ if (of_property_read_u32(node, "fsl,tx-deemph-gen1",
+ &imx6_pcie->tx_deemph_gen1))
+ imx6_pcie->tx_deemph_gen1 = 0;
+
+ if (of_property_read_u32(node, "fsl,tx-deemph-gen2-3p5db",
+ &imx6_pcie->tx_deemph_gen2_3p5db))
+ imx6_pcie->tx_deemph_gen2_3p5db = 0;
+
+ if (of_property_read_u32(node, "fsl,tx-deemph-gen2-6db",
+ &imx6_pcie->tx_deemph_gen2_6db))
+ imx6_pcie->tx_deemph_gen2_6db = 20;
+
+ if (of_property_read_u32(node, "fsl,tx-swing-full",
+ &imx6_pcie->tx_swing_full))
+ imx6_pcie->tx_swing_full = 127;
+
+ if (of_property_read_u32(node, "fsl,tx-swing-low",
+ &imx6_pcie->tx_swing_low))
+ imx6_pcie->tx_swing_low = 127;
+
+ /* Limit link speed */
+ ret = of_property_read_u32(node, "fsl,max-link-speed",
+ &imx6_pcie->link_gen);
+ if (ret)
+ imx6_pcie->link_gen = 1;
+
+ imx6_pcie->vpcie = devm_regulator_get_optional(&pdev->dev, "vpcie");
+ if (IS_ERR(imx6_pcie->vpcie)) {
+ if (PTR_ERR(imx6_pcie->vpcie) != -ENODEV)
+ return PTR_ERR(imx6_pcie->vpcie);
+ imx6_pcie->vpcie = NULL;
+ }
+
+ platform_set_drvdata(pdev, imx6_pcie);
+
+ ret = imx6_pcie_attach_pd(dev);
+ if (ret)
+ return ret;
+
+ ret = imx6_add_pcie_port(imx6_pcie, pdev);
+ if (ret < 0)
+ return ret;
+
+ if (pci_msi_enabled()) {
+ val = dw_pcie_readw_dbi(pci, PCIE_RC_IMX6_MSI_CAP +
+ PCI_MSI_FLAGS);
+ val |= PCI_MSI_FLAGS_ENABLE;
+ dw_pcie_writew_dbi(pci, PCIE_RC_IMX6_MSI_CAP + PCI_MSI_FLAGS,
+ val);
+ }
+
+ return 0;
+}
+
+static void imx6_pcie_shutdown(struct platform_device *pdev)
+{
+ struct imx6_pcie *imx6_pcie = platform_get_drvdata(pdev);
+
+ /* bring down link, so bootloader gets clean state in case of reboot */
+ imx6_pcie_assert_core_reset(imx6_pcie);
+}
+
+static const struct imx6_pcie_drvdata drvdata[] = {
+ [IMX6Q] = {
+ .variant = IMX6Q,
+ .flags = IMX6_PCIE_FLAG_IMX6_PHY |
+ IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE,
+ .dbi_length = 0x200,
+ },
+ [IMX6SX] = {
+ .variant = IMX6SX,
+ .flags = IMX6_PCIE_FLAG_IMX6_PHY |
+ IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE |
+ IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
+ },
+ [IMX6QP] = {
+ .variant = IMX6QP,
+ .flags = IMX6_PCIE_FLAG_IMX6_PHY |
+ IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE,
+ },
+ [IMX7D] = {
+ .variant = IMX7D,
+ .flags = IMX6_PCIE_FLAG_SUPPORTS_SUSPEND,
+ },
+ [IMX8MQ] = {
+ .variant = IMX8MQ,
+ },
+};
+
+static const struct of_device_id imx6_pcie_of_match[] = {
+ { .compatible = "fsl,imx6q-pcie", .data = &drvdata[IMX6Q], },
+ { .compatible = "fsl,imx6sx-pcie", .data = &drvdata[IMX6SX], },
+ { .compatible = "fsl,imx6qp-pcie", .data = &drvdata[IMX6QP], },
+ { .compatible = "fsl,imx7d-pcie", .data = &drvdata[IMX7D], },
+ { .compatible = "fsl,imx8mq-pcie", .data = &drvdata[IMX8MQ], } ,
+ {},
+};
+
+static struct platform_driver imx6_pcie_driver = {
+ .driver = {
+ .name = "imx6q-pcie",
+ .of_match_table = imx6_pcie_of_match,
+ .suppress_bind_attrs = true,
+ .pm = &imx6_pcie_pm_ops,
+ .probe_type = PROBE_PREFER_ASYNCHRONOUS,
+ },
+ .probe = imx6_pcie_probe,
+ .shutdown = imx6_pcie_shutdown,
+};
+
+static void imx6_pcie_quirk(struct pci_dev *dev)
+{
+ struct pci_bus *bus = dev->bus;
+ struct pcie_port *pp = bus->sysdata;
+
+ /* Bus parent is the PCI bridge, its parent is this platform driver */
+ if (!bus->dev.parent || !bus->dev.parent->parent)
+ return;
+
+ /* Make sure we only quirk devices associated with this driver */
+ if (bus->dev.parent->parent->driver != &imx6_pcie_driver.driver)
+ return;
+
+ if (bus->number == pp->root_bus_nr) {
+ struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ struct imx6_pcie *imx6_pcie = to_imx6_pcie(pci);
+
+ /*
+ * Limit config length to avoid the kernel reading beyond
+ * the register set and causing an abort on i.MX 6Quad
+ */
+ if (imx6_pcie->drvdata->dbi_length) {
+ dev->cfg_size = imx6_pcie->drvdata->dbi_length;
+ dev_info(&dev->dev, "Limiting cfg_size to %d\n",
+ dev->cfg_size);
+ }
+ }
+}
+DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_SYNOPSYS, 0xabcd,
+ PCI_CLASS_BRIDGE_PCI, 8, imx6_pcie_quirk);
+
+static int __init imx6_pcie_init(void)
+{
+#ifdef CONFIG_ARM
+ struct device_node *np;
+
+ np = of_find_matching_node(NULL, imx6_pcie_of_match);
+ if (!np)
+ return -ENODEV;
+ of_node_put(np);
+
+ /*
+ * Since probe() can be deferred we need to make sure that
+ * hook_fault_code is not called after __init memory is freed
+ * by kernel and since imx6q_pcie_abort_handler() is a no-op,
+ * we can install the handler here without risking it
+ * accessing some uninitialized driver state.
+ */
+ hook_fault_code(8, imx6q_pcie_abort_handler, SIGBUS, 0,
+ "external abort on non-linefetch");
+#endif
+
+ return platform_driver_register(&imx6_pcie_driver);
+}
+device_initcall(imx6_pcie_init);