ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/uboot/board/atmel/at91sam9261ek/at91sam9261ek.c b/marvell/uboot/board/atmel/at91sam9261ek/at91sam9261ek.c
new file mode 100644
index 0000000..3e8f062
--- /dev/null
+++ b/marvell/uboot/board/atmel/at91sam9261ek/at91sam9261ek.c
@@ -0,0 +1,281 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian@popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/at91sam9261.h>
+#include <asm/arch/at91sam9261_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/gpio.h>
+#include <lcd.h>
+#include <atmel_lcdc.h>
+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
+#include <net.h>
+#include <netdev.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+#ifdef CONFIG_CMD_NAND
+static void at91sam9261ek_nand_hw_init(void)
+{
+ struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+ struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ unsigned long csa;
+
+ /* Enable CS3 */
+ csa = readl(&matrix->ebicsa);
+ csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
+
+ writel(csa, &matrix->ebicsa);
+
+ /* Configure SMC CS3 for NAND/SmartMedia */
+#ifdef CONFIG_AT91SAM9G10EK
+ writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[3].setup);
+ writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(7) |
+ AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(7),
+ &smc->cs[3].pulse);
+ writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
+ &smc->cs[3].cycle);
+#else
+ writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[3].setup);
+ writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
+ AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
+ &smc->cs[3].pulse);
+ writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
+ &smc->cs[3].cycle);
+#endif
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+#ifdef CONFIG_SYS_NAND_DBW_16
+ AT91_SMC_MODE_DBW_16 |
+#else /* CONFIG_SYS_NAND_DBW_8 */
+ AT91_SMC_MODE_DBW_8 |
+#endif
+ AT91_SMC_MODE_TDF_CYCLE(2),
+ &smc->cs[3].mode);
+
+ writel(1 << ATMEL_ID_PIOC, &pmc->pcer);
+
+ /* Configure RDY/BSY */
+ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+
+ /* Enable NandFlash */
+ at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+
+ at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */
+ at91_set_A_periph(AT91_PIN_PC1, 0); /* NANDWE */
+}
+#endif
+
+#ifdef CONFIG_DRIVER_DM9000
+static void at91sam9261ek_dm9000_hw_init(void)
+{
+ struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+
+ /* Configure SMC CS2 for DM9000 */
+#ifdef CONFIG_AT91SAM9G10EK
+ writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(3) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[2].setup);
+ writel(AT91_SMC_PULSE_NWE(6) | AT91_SMC_PULSE_NCS_WR(8) |
+ AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(8),
+ &smc->cs[2].pulse);
+ writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20),
+ &smc->cs[2].cycle);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+ AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
+ AT91_SMC_MODE_TDF_CYCLE(1),
+ &smc->cs[2].mode);
+#else
+ writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[2].setup);
+ writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
+ AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
+ &smc->cs[2].pulse);
+ writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
+ &smc->cs[2].cycle);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+ AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
+ AT91_SMC_MODE_TDF_CYCLE(1),
+ &smc->cs[2].mode);
+#endif
+
+ /* Configure Reset signal as output */
+ at91_set_gpio_output(AT91_PIN_PC10, 0);
+
+ /* Configure Interrupt pin as input, no pull-up */
+ at91_set_gpio_input(AT91_PIN_PC11, 0);
+}
+#endif
+
+#ifdef CONFIG_LCD
+vidinfo_t panel_info = {
+ vl_col: 240,
+ vl_row: 320,
+ vl_clk: 4965000,
+ vl_sync: ATMEL_LCDC_INVLINE_INVERTED |
+ ATMEL_LCDC_INVFRAME_INVERTED,
+ vl_bpix: 3,
+ vl_tft: 1,
+ vl_hsync_len: 5,
+ vl_left_margin: 1,
+ vl_right_margin:33,
+ vl_vsync_len: 1,
+ vl_upper_margin:1,
+ vl_lower_margin:0,
+ mmio: ATMEL_BASE_LCDC,
+};
+
+void lcd_enable(void)
+{
+ at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
+}
+
+void lcd_disable(void)
+{
+ at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
+}
+
+static void at91sam9261ek_lcd_hw_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+ at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */
+ at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */
+ at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */
+ at91_set_A_periph(AT91_PIN_PB4, 0); /* LCDCC */
+ at91_set_A_periph(AT91_PIN_PB7, 0); /* LCDD2 */
+ at91_set_A_periph(AT91_PIN_PB8, 0); /* LCDD3 */
+ at91_set_A_periph(AT91_PIN_PB9, 0); /* LCDD4 */
+ at91_set_A_periph(AT91_PIN_PB10, 0); /* LCDD5 */
+ at91_set_A_periph(AT91_PIN_PB11, 0); /* LCDD6 */
+ at91_set_A_periph(AT91_PIN_PB12, 0); /* LCDD7 */
+ at91_set_A_periph(AT91_PIN_PB15, 0); /* LCDD10 */
+ at91_set_A_periph(AT91_PIN_PB16, 0); /* LCDD11 */
+ at91_set_A_periph(AT91_PIN_PB17, 0); /* LCDD12 */
+ at91_set_A_periph(AT91_PIN_PB18, 0); /* LCDD13 */
+ at91_set_A_periph(AT91_PIN_PB19, 0); /* LCDD14 */
+ at91_set_A_periph(AT91_PIN_PB20, 0); /* LCDD15 */
+ at91_set_B_periph(AT91_PIN_PB23, 0); /* LCDD18 */
+ at91_set_B_periph(AT91_PIN_PB24, 0); /* LCDD19 */
+ at91_set_B_periph(AT91_PIN_PB25, 0); /* LCDD20 */
+ at91_set_B_periph(AT91_PIN_PB26, 0); /* LCDD21 */
+ at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */
+ at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */
+
+ writel(AT91_PMC_HCK1, &pmc->scer);
+
+ /* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */
+#ifdef CONFIG_AT91SAM9261EK
+ gd->fb_base = ATMEL_BASE_SRAM;
+#endif
+}
+
+#ifdef CONFIG_LCD_INFO
+#include <nand.h>
+#include <version.h>
+
+void lcd_show_board_info(void)
+{
+ ulong dram_size, nand_size;
+ int i;
+ char temp[32];
+
+ lcd_printf ("%s\n", U_BOOT_VERSION);
+ lcd_printf ("(C) 2008 ATMEL Corp\n");
+ lcd_printf ("at91support@atmel.com\n");
+ lcd_printf ("%s CPU at %s MHz\n",
+ ATMEL_CPU_NAME,
+ strmhz(temp, get_cpu_clk_rate()));
+
+ dram_size = 0;
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
+ dram_size += gd->bd->bi_dram[i].size;
+ nand_size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
+ nand_size += nand_info[i].size;
+ lcd_printf (" %ld MB SDRAM, %ld MB NAND\n",
+ dram_size >> 20,
+ nand_size >> 20 );
+}
+#endif /* CONFIG_LCD_INFO */
+#endif
+
+int board_init(void)
+{
+#ifdef CONFIG_AT91SAM9G10EK
+ /* arch number of AT91SAM9G10EK-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK;
+#else
+ /* arch number of AT91SAM9261EK-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK;
+#endif
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ at91_seriald_hw_init();
+#ifdef CONFIG_CMD_NAND
+ at91sam9261ek_nand_hw_init();
+#endif
+#ifdef CONFIG_HAS_DATAFLASH
+ at91_spi0_hw_init(1 << 0);
+#endif
+#ifdef CONFIG_DRIVER_DM9000
+ at91sam9261ek_dm9000_hw_init();
+#endif
+#ifdef CONFIG_LCD
+ at91sam9261ek_lcd_hw_init();
+#endif
+ return 0;
+}
+
+#ifdef CONFIG_DRIVER_DM9000
+int board_eth_init(bd_t *bis)
+{
+ return dm9000_initialize(bis);
+}
+#endif
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
+
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+#ifdef CONFIG_DRIVER_DM9000
+ /*
+ * Initialize ethernet HW addr prior to starting Linux,
+ * needed for nfsroot
+ */
+ eth_init(gd->bd);
+#endif
+}
+#endif