ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/uboot/board/freescale/p1022ds/ddr.c b/marvell/uboot/board/freescale/p1022ds/ddr.c
new file mode 100644
index 0000000..09212bc
--- /dev/null
+++ b/marvell/uboot/board/freescale/p1022ds/ddr.c
@@ -0,0 +1,107 @@
+/*
+ * Copyright 2010 Freescale Semiconductor, Inc.
+ * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
+ * Timur Tabi <timur@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 clk_adjust; /* Range: 0-8 */
+ u32 cpo; /* Range: 2-31 */
+ u32 write_data_delay; /* Range: 0-6 */
+ u32 force_2t;
+};
+
+/*
+ * This table contains all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+static const struct board_specific_parameters dimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| clk| cpo|wrdata|2T
+ * ranks| mhz|adjst| | delay|
+ */
+ {1, 549, 5, 31, 3, 0},
+ {1, 850, 5, 31, 5, 0},
+ {2, 549, 5, 31, 3, 0},
+ {2, 850, 5, 31, 5, 0},
+ {}
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ unsigned long ddr_freq;
+ unsigned int i;
+
+
+ if (ctrl_num) {
+ printf("Wrong parameter for controller number %d", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ /* set odt_rd_cfg and odt_wr_cfg. */
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 1;
+ }
+
+ pbsp = dimm0;
+ /*
+ * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay =
+ pbsp->write_data_delay;
+ popts->twot_en = pbsp->force_2t;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found "
+ "for data rate %lu MT/s!\n"
+ "Trying to use the highest speed (%u) parameters\n",
+ ddr_freq, pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay = pbsp->write_data_delay;
+ popts->twot_en = pbsp->force_2t;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+
+found:
+ popts->half_strength_driver_enable = 1;
+
+ /* Per AN4039, enable ZQ calibration. */
+ popts->zq_en = 1;
+
+ /*
+ * For wake-up on ARP, we need auto self refresh enabled
+ */
+ popts->auto_self_refresh_en = 1;
+ popts->sr_it = 0xb;
+}