ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/uboot/board/sbc8548/ddr.c b/marvell/uboot/board/sbc8548/ddr.c
new file mode 100644
index 0000000..24cc776
--- /dev/null
+++ b/marvell/uboot/board/sbc8548/ddr.c
@@ -0,0 +1,134 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ /*
+ * Factors to consider for clock adjust:
+ * - number of chips on bus
+ * - position of slot
+ * - DDR1 vs. DDR2?
+ * - ???
+ *
+ * This needs to be determined on a board-by-board basis.
+ * 0110 3/4 cycle late
+ * 0111 7/8 cycle late
+ */
+ popts->clk_adjust = 7;
+
+ /*
+ * Factors to consider for CPO:
+ * - frequency
+ * - ddr1 vs. ddr2
+ */
+ popts->cpo_override = 10;
+
+ /*
+ * Factors to consider for write data delay:
+ * - number of DIMMs
+ *
+ * 1 = 1/4 clock delay
+ * 2 = 1/2 clock delay
+ * 3 = 3/4 clock delay
+ * 4 = 1 clock delay
+ * 5 = 5/4 clock delay
+ * 6 = 3/2 clock delay
+ */
+ popts->write_data_delay = 3;
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+}
+
+#ifdef CONFIG_SPD_EEPROM
+/*
+ * Workaround for hardware errata. An i2c address conflict
+ * existed on earlier boards; the workaround moved the DDR
+ * SPD from 0x51 to 0x53. So we try and read 0x53 1st, and
+ * if that fails, then fall back to reading at 0x51.
+ */
+void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address)
+{
+ int ret;
+
+#ifdef ALT_SPD_EEPROM_ADDRESS
+ if (i2c_address == SPD_EEPROM_ADDRESS) {
+ ret = i2c_read(ALT_SPD_EEPROM_ADDRESS, 0, 1, (uchar *)spd,
+ sizeof(generic_spd_eeprom_t));
+ if (ret == 0)
+ return; /* Good data at 0x53 */
+ memset(spd, 0, sizeof(generic_spd_eeprom_t));
+ }
+#endif
+ ret = i2c_read(i2c_address, 0, 1, (uchar *)spd,
+ sizeof(generic_spd_eeprom_t));
+ if (ret) {
+ printf("DDR: failed to read SPD from addr %u\n", i2c_address);
+ memset(spd, 0, sizeof(generic_spd_eeprom_t));
+ }
+}
+
+#else
+/*
+ * fixed_sdram init -- doesn't use serial presence detect.
+ * Assumes 256MB DDR2 SDRAM SODIMM, without ECC, running at DDR400 speed.
+ */
+phys_size_t fixed_sdram(void)
+{
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
+
+ out_be32(&ddr->cs0_bnds, 0x0000007f);
+ out_be32(&ddr->cs1_bnds, 0x008000ff);
+ out_be32(&ddr->cs2_bnds, 0x00000000);
+ out_be32(&ddr->cs3_bnds, 0x00000000);
+
+ out_be32(&ddr->cs0_config, 0x80010101);
+ out_be32(&ddr->cs1_config, 0x80010101);
+ out_be32(&ddr->cs2_config, 0x00000000);
+ out_be32(&ddr->cs3_config, 0x00000000);
+
+ out_be32(&ddr->timing_cfg_3, 0x00000000);
+ out_be32(&ddr->timing_cfg_0, 0x00220802);
+ out_be32(&ddr->timing_cfg_1, 0x38377322);
+ out_be32(&ddr->timing_cfg_2, 0x0fa044C7);
+
+ out_be32(&ddr->sdram_cfg, 0x4300C000);
+ out_be32(&ddr->sdram_cfg_2, 0x24401000);
+
+ out_be32(&ddr->sdram_mode, 0x23C00542);
+ out_be32(&ddr->sdram_mode_2, 0x00000000);
+
+ out_be32(&ddr->sdram_interval, 0x05080100);
+ out_be32(&ddr->sdram_md_cntl, 0x00000000);
+ out_be32(&ddr->sdram_data_init, 0x00000000);
+ out_be32(&ddr->sdram_clk_cntl, 0x03800000);
+ asm("sync;isync;msync");
+ udelay(500);
+
+ #ifdef CONFIG_DDR_ECC
+ /* Enable ECC checking */
+ out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | 0x20000000);
+ #else
+ out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
+ #endif
+
+ return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+}
+#endif