ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/uboot/drivers/i2c/omap24xx_i2c.h b/marvell/uboot/drivers/i2c/omap24xx_i2c.h
new file mode 100644
index 0000000..3dae295
--- /dev/null
+++ b/marvell/uboot/drivers/i2c/omap24xx_i2c.h
@@ -0,0 +1,154 @@
+/*
+ * (C) Copyright 2004-2010
+ * Texas Instruments, <www.ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef _OMAP2PLUS_I2C_H_
+#define _OMAP2PLUS_I2C_H_
+
+/* I2C masks */
+
+/* I2C Interrupt Enable Register (I2C_IE): */
+#define I2C_IE_GC_IE (1 << 5)
+#define I2C_IE_XRDY_IE (1 << 4) /* Transmit data ready interrupt enable */
+#define I2C_IE_RRDY_IE (1 << 3) /* Receive data ready interrupt enable */
+#define I2C_IE_ARDY_IE (1 << 2) /* Register access ready interrupt enable */
+#define I2C_IE_NACK_IE (1 << 1) /* No acknowledgment interrupt enable */
+#define I2C_IE_AL_IE (1 << 0) /* Arbitration lost interrupt enable */
+
+/* I2C Status Register (I2C_STAT): */
+
+#define I2C_STAT_SBD (1 << 15) /* Single byte data */
+#define I2C_STAT_BB (1 << 12) /* Bus busy */
+#define I2C_STAT_ROVR (1 << 11) /* Receive overrun */
+#define I2C_STAT_XUDF (1 << 10) /* Transmit underflow */
+#define I2C_STAT_AAS (1 << 9) /* Address as slave */
+#define I2C_STAT_GC (1 << 5)
+#define I2C_STAT_XRDY (1 << 4) /* Transmit data ready */
+#define I2C_STAT_RRDY (1 << 3) /* Receive data ready */
+#define I2C_STAT_ARDY (1 << 2) /* Register access ready */
+#define I2C_STAT_NACK (1 << 1) /* No acknowledgment interrupt enable */
+#define I2C_STAT_AL (1 << 0) /* Arbitration lost interrupt enable */
+
+/* I2C Interrupt Code Register (I2C_INTCODE): */
+
+#define I2C_INTCODE_MASK 7
+#define I2C_INTCODE_NONE 0
+#define I2C_INTCODE_AL 1 /* Arbitration lost */
+#define I2C_INTCODE_NAK 2 /* No acknowledgement/general call */
+#define I2C_INTCODE_ARDY 3 /* Register access ready */
+#define I2C_INTCODE_RRDY 4 /* Rcv data ready */
+#define I2C_INTCODE_XRDY 5 /* Xmit data ready */
+
+/* I2C Buffer Configuration Register (I2C_BUF): */
+
+#define I2C_BUF_RDMA_EN (1 << 15) /* Receive DMA channel enable */
+#define I2C_BUF_XDMA_EN (1 << 7) /* Transmit DMA channel enable */
+
+/* I2C Configuration Register (I2C_CON): */
+
+#define I2C_CON_EN (1 << 15) /* I2C module enable */
+#define I2C_CON_BE (1 << 14) /* Big endian mode */
+#define I2C_CON_STB (1 << 11) /* Start byte mode (master mode only) */
+#define I2C_CON_MST (1 << 10) /* Master/slave mode */
+#define I2C_CON_TRX (1 << 9) /* Transmitter/receiver mode */
+ /* (master mode only) */
+#define I2C_CON_XA (1 << 8) /* Expand address */
+#define I2C_CON_STP (1 << 1) /* Stop condition (master mode only) */
+#define I2C_CON_STT (1 << 0) /* Start condition (master mode only) */
+
+/* I2C System Test Register (I2C_SYSTEST): */
+
+#define I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */
+#define I2C_SYSTEST_FREE (1 << 14) /* Free running mode, on brkpoint) */
+#define I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */
+#define I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */
+#define I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense input value */
+#define I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive output value */
+#define I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense input value */
+#define I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive output value */
+
+/* I2C System Status Register (I2C_SYSS): */
+
+#define I2C_SYSS_RDONE (1 << 0) /* Internel reset monitoring */
+
+#define I2C_SCLL_SCLL 0
+#define I2C_SCLL_SCLL_M 0xFF
+#define I2C_SCLL_HSSCLL 8
+#define I2C_SCLH_HSSCLL_M 0xFF
+#define I2C_SCLH_SCLH 0
+#define I2C_SCLH_SCLH_M 0xFF
+#define I2C_SCLH_HSSCLH 8
+#define I2C_SCLH_HSSCLH_M 0xFF
+
+#define OMAP_I2C_STANDARD 100000
+#define OMAP_I2C_FAST_MODE 400000
+#define OMAP_I2C_HIGH_SPEED 3400000
+
+#define SYSTEM_CLOCK_12 12000000
+#define SYSTEM_CLOCK_13 13000000
+#define SYSTEM_CLOCK_192 19200000
+#define SYSTEM_CLOCK_96 96000000
+
+/* Use the reference value of 96MHz if not explicitly set by the board */
+#ifndef I2C_IP_CLK
+#define I2C_IP_CLK SYSTEM_CLOCK_96
+#endif
+
+/*
+ * The reference minimum clock for high speed is 19.2MHz.
+ * The linux 2.6.30 kernel uses this value.
+ * The reference minimum clock for fast mode is 9.6MHz
+ * The reference minimum clock for standard mode is 4MHz
+ * In TRM, the value of 12MHz is used.
+ */
+#ifndef I2C_INTERNAL_SAMPLING_CLK
+#define I2C_INTERNAL_SAMPLING_CLK 19200000
+#endif
+
+/*
+ * The equation for the low and high time is
+ * tlow = scll + scll_trim = (sampling clock * tlow_duty) / speed
+ * thigh = sclh + sclh_trim = (sampling clock * (1 - tlow_duty)) / speed
+ *
+ * If the duty cycle is 50%
+ *
+ * tlow = scll + scll_trim = sampling clock / (2 * speed)
+ * thigh = sclh + sclh_trim = sampling clock / (2 * speed)
+ *
+ * In TRM
+ * scll_trim = 7
+ * sclh_trim = 5
+ *
+ * The linux 2.6.30 kernel uses
+ * scll_trim = 6
+ * sclh_trim = 6
+ *
+ * These are the trim values for standard and fast speed
+ */
+#ifndef I2C_FASTSPEED_SCLL_TRIM
+#define I2C_FASTSPEED_SCLL_TRIM 6
+#endif
+#ifndef I2C_FASTSPEED_SCLH_TRIM
+#define I2C_FASTSPEED_SCLH_TRIM 6
+#endif
+
+/* These are the trim values for high speed */
+#ifndef I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM
+#define I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM
+#endif
+#ifndef I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM
+#define I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM
+#endif
+#ifndef I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM
+#define I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM
+#endif
+#ifndef I2C_HIGHSPEED_PHASE_TWO_SCLH_TRIM
+#define I2C_HIGHSPEED_PHASE_TWO_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM
+#endif
+
+#define I2C_PSC_MAX 0x0f
+#define I2C_PSC_MIN 0x00
+
+#endif /* _OMAP24XX_I2C_H_ */