ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/uboot/drivers/mtd/nand/davinci_nand.c b/marvell/uboot/drivers/mtd/nand/davinci_nand.c
new file mode 100644
index 0000000..5b17d7b
--- /dev/null
+++ b/marvell/uboot/drivers/mtd/nand/davinci_nand.c
@@ -0,0 +1,650 @@
+/*
+ * NAND driver for TI DaVinci based boards.
+ *
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * Based on Linux DaVinci NAND driver by TI. Original copyright follows:
+ */
+
+/*
+ *
+ * linux/drivers/mtd/nand/nand_davinci.c
+ *
+ * NAND Flash Driver
+ *
+ * Copyright (C) 2006 Texas Instruments.
+ *
+ * ----------------------------------------------------------------------------
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * ----------------------------------------------------------------------------
+ *
+ * Overview:
+ * This is a device driver for the NAND flash device found on the
+ * DaVinci board which utilizes the Samsung k9k2g08 part.
+ *
+ Modifications:
+ ver. 1.0: Feb 2005, Vinod/Sudhakar
+ -
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <nand.h>
+#include <asm/arch/nand_defs.h>
+#include <asm/arch/emif_defs.h>
+
+/* Definitions for 4-bit hardware ECC */
+#define NAND_TIMEOUT 10240
+#define NAND_ECC_BUSY 0xC
+#define NAND_4BITECC_MASK 0x03FF03FF
+#define EMIF_NANDFSR_ECC_STATE_MASK 0x00000F00
+#define ECC_STATE_NO_ERR 0x0
+#define ECC_STATE_TOO_MANY_ERRS 0x1
+#define ECC_STATE_ERR_CORR_COMP_P 0x2
+#define ECC_STATE_ERR_CORR_COMP_N 0x3
+
+/*
+ * Exploit the little endianness of the ARM to do multi-byte transfers
+ * per device read. This can perform over twice as quickly as individual
+ * byte transfers when buffer alignment is conducive.
+ *
+ * NOTE: This only works if the NAND is not connected to the 2 LSBs of
+ * the address bus. On Davinci EVM platforms this has always been true.
+ */
+static void nand_davinci_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ const u32 *nand = chip->IO_ADDR_R;
+
+ /* Make sure that buf is 32 bit aligned */
+ if (((int)buf & 0x3) != 0) {
+ if (((int)buf & 0x1) != 0) {
+ if (len) {
+ *buf = readb(nand);
+ buf += 1;
+ len--;
+ }
+ }
+
+ if (((int)buf & 0x3) != 0) {
+ if (len >= 2) {
+ *(u16 *)buf = readw(nand);
+ buf += 2;
+ len -= 2;
+ }
+ }
+ }
+
+ /* copy aligned data */
+ while (len >= 4) {
+ *(u32 *)buf = __raw_readl(nand);
+ buf += 4;
+ len -= 4;
+ }
+
+ /* mop up any remaining bytes */
+ if (len) {
+ if (len >= 2) {
+ *(u16 *)buf = readw(nand);
+ buf += 2;
+ len -= 2;
+ }
+
+ if (len)
+ *buf = readb(nand);
+ }
+}
+
+static void nand_davinci_write_buf(struct mtd_info *mtd, const uint8_t *buf,
+ int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ const u32 *nand = chip->IO_ADDR_W;
+
+ /* Make sure that buf is 32 bit aligned */
+ if (((int)buf & 0x3) != 0) {
+ if (((int)buf & 0x1) != 0) {
+ if (len) {
+ writeb(*buf, nand);
+ buf += 1;
+ len--;
+ }
+ }
+
+ if (((int)buf & 0x3) != 0) {
+ if (len >= 2) {
+ writew(*(u16 *)buf, nand);
+ buf += 2;
+ len -= 2;
+ }
+ }
+ }
+
+ /* copy aligned data */
+ while (len >= 4) {
+ __raw_writel(*(u32 *)buf, nand);
+ buf += 4;
+ len -= 4;
+ }
+
+ /* mop up any remaining bytes */
+ if (len) {
+ if (len >= 2) {
+ writew(*(u16 *)buf, nand);
+ buf += 2;
+ len -= 2;
+ }
+
+ if (len)
+ writeb(*buf, nand);
+ }
+}
+
+static void nand_davinci_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ u_int32_t IO_ADDR_W = (u_int32_t)this->IO_ADDR_W;
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+ IO_ADDR_W &= ~(MASK_ALE|MASK_CLE);
+
+ if (ctrl & NAND_CLE)
+ IO_ADDR_W |= MASK_CLE;
+ if (ctrl & NAND_ALE)
+ IO_ADDR_W |= MASK_ALE;
+ this->IO_ADDR_W = (void __iomem *) IO_ADDR_W;
+ }
+
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, IO_ADDR_W);
+}
+
+#ifdef CONFIG_SYS_NAND_HW_ECC
+
+static u_int32_t nand_davinci_readecc(struct mtd_info *mtd)
+{
+ u_int32_t ecc = 0;
+
+ ecc = __raw_readl(&(davinci_emif_regs->nandfecc[
+ CONFIG_SYS_NAND_CS - 2]));
+
+ return ecc;
+}
+
+static void nand_davinci_enable_hwecc(struct mtd_info *mtd, int mode)
+{
+ u_int32_t val;
+
+ /* reading the ECC result register resets the ECC calculation */
+ nand_davinci_readecc(mtd);
+
+ val = __raw_readl(&davinci_emif_regs->nandfcr);
+ val |= DAVINCI_NANDFCR_NAND_ENABLE(CONFIG_SYS_NAND_CS);
+ val |= DAVINCI_NANDFCR_1BIT_ECC_START(CONFIG_SYS_NAND_CS);
+ __raw_writel(val, &davinci_emif_regs->nandfcr);
+}
+
+static int nand_davinci_calculate_ecc(struct mtd_info *mtd, const u_char *dat,
+ u_char *ecc_code)
+{
+ u_int32_t tmp;
+
+ tmp = nand_davinci_readecc(mtd);
+
+ /* Squeeze 4 bytes ECC into 3 bytes by removing RESERVED bits
+ * and shifting. RESERVED bits are 31 to 28 and 15 to 12. */
+ tmp = (tmp & 0x00000fff) | ((tmp & 0x0fff0000) >> 4);
+
+ /* Invert so that erased block ECC is correct */
+ tmp = ~tmp;
+
+ *ecc_code++ = tmp;
+ *ecc_code++ = tmp >> 8;
+ *ecc_code++ = tmp >> 16;
+
+ /* NOTE: the above code matches mainline Linux:
+ * .PQR.stu ==> ~PQRstu
+ *
+ * MontaVista/TI kernels encode those bytes differently, use
+ * complicated (and allegedly sometimes-wrong) correction code,
+ * and usually shipped with U-Boot that uses software ECC:
+ * .PQR.stu ==> PsQRtu
+ *
+ * If you need MV/TI compatible NAND I/O in U-Boot, it should
+ * be possible to (a) change the mangling above, (b) reverse
+ * that mangling in nand_davinci_correct_data() below.
+ */
+
+ return 0;
+}
+
+static int nand_davinci_correct_data(struct mtd_info *mtd, u_char *dat,
+ u_char *read_ecc, u_char *calc_ecc)
+{
+ struct nand_chip *this = mtd->priv;
+ u_int32_t ecc_nand = read_ecc[0] | (read_ecc[1] << 8) |
+ (read_ecc[2] << 16);
+ u_int32_t ecc_calc = calc_ecc[0] | (calc_ecc[1] << 8) |
+ (calc_ecc[2] << 16);
+ u_int32_t diff = ecc_calc ^ ecc_nand;
+
+ if (diff) {
+ if ((((diff >> 12) ^ diff) & 0xfff) == 0xfff) {
+ /* Correctable error */
+ if ((diff >> (12 + 3)) < this->ecc.size) {
+ uint8_t find_bit = 1 << ((diff >> 12) & 7);
+ uint32_t find_byte = diff >> (12 + 3);
+
+ dat[find_byte] ^= find_bit;
+ MTDDEBUG(MTD_DEBUG_LEVEL0, "Correcting single "
+ "bit ECC error at offset: %d, bit: "
+ "%d\n", find_byte, find_bit);
+ return 1;
+ } else {
+ return -1;
+ }
+ } else if (!(diff & (diff - 1))) {
+ /* Single bit ECC error in the ECC itself,
+ nothing to fix */
+ MTDDEBUG(MTD_DEBUG_LEVEL0, "Single bit ECC error in "
+ "ECC.\n");
+ return 1;
+ } else {
+ /* Uncorrectable error */
+ MTDDEBUG(MTD_DEBUG_LEVEL0, "ECC UNCORRECTED_ERROR 1\n");
+ return -1;
+ }
+ }
+ return 0;
+}
+#endif /* CONFIG_SYS_NAND_HW_ECC */
+
+#ifdef CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
+static struct nand_ecclayout nand_davinci_4bit_layout_oobfirst = {
+#if defined(CONFIG_SYS_NAND_PAGE_2K)
+ .eccbytes = 40,
+#ifdef CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
+ .eccpos = {
+ 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,
+ 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
+ 38, 39, 40, 41, 42, 43, 44, 45, 46, 47,
+ 54, 55, 56, 57, 58, 59, 60, 61, 62, 63,
+ },
+ .oobfree = {
+ {2, 4}, {16, 6}, {32, 6}, {48, 6},
+ },
+#else
+ .eccpos = {
+ 24, 25, 26, 27, 28,
+ 29, 30, 31, 32, 33, 34, 35, 36, 37, 38,
+ 39, 40, 41, 42, 43, 44, 45, 46, 47, 48,
+ 49, 50, 51, 52, 53, 54, 55, 56, 57, 58,
+ 59, 60, 61, 62, 63,
+ },
+ .oobfree = {
+ {.offset = 2, .length = 22, },
+ },
+#endif /* #ifdef CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC */
+#elif defined(CONFIG_SYS_NAND_PAGE_4K)
+ .eccbytes = 80,
+ .eccpos = {
+ 48, 49, 50, 51, 52, 53, 54, 55, 56, 57,
+ 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
+ 68, 69, 70, 71, 72, 73, 74, 75, 76, 77,
+ 78, 79, 80, 81, 82, 83, 84, 85, 86, 87,
+ 88, 89, 90, 91, 92, 93, 94, 95, 96, 97,
+ 98, 99, 100, 101, 102, 103, 104, 105, 106, 107,
+ 108, 109, 110, 111, 112, 113, 114, 115, 116, 117,
+ 118, 119, 120, 121, 122, 123, 124, 125, 126, 127,
+ },
+ .oobfree = {
+ {.offset = 2, .length = 46, },
+ },
+#endif
+};
+
+static void nand_davinci_4bit_enable_hwecc(struct mtd_info *mtd, int mode)
+{
+ u32 val;
+
+ switch (mode) {
+ case NAND_ECC_WRITE:
+ case NAND_ECC_READ:
+ /*
+ * Start a new ECC calculation for reading or writing 512 bytes
+ * of data.
+ */
+ val = __raw_readl(&davinci_emif_regs->nandfcr);
+ val &= ~DAVINCI_NANDFCR_4BIT_ECC_SEL_MASK;
+ val |= DAVINCI_NANDFCR_NAND_ENABLE(CONFIG_SYS_NAND_CS);
+ val |= DAVINCI_NANDFCR_4BIT_ECC_SEL(CONFIG_SYS_NAND_CS);
+ val |= DAVINCI_NANDFCR_4BIT_ECC_START;
+ __raw_writel(val, &davinci_emif_regs->nandfcr);
+ break;
+ case NAND_ECC_READSYN:
+ val = __raw_readl(&davinci_emif_regs->nand4bitecc[0]);
+ break;
+ default:
+ break;
+ }
+}
+
+static u32 nand_davinci_4bit_readecc(struct mtd_info *mtd, unsigned int ecc[4])
+{
+ int i;
+
+ for (i = 0; i < 4; i++) {
+ ecc[i] = __raw_readl(&davinci_emif_regs->nand4bitecc[i]) &
+ NAND_4BITECC_MASK;
+ }
+
+ return 0;
+}
+
+static int nand_davinci_4bit_calculate_ecc(struct mtd_info *mtd,
+ const uint8_t *dat,
+ uint8_t *ecc_code)
+{
+ unsigned int hw_4ecc[4];
+ unsigned int i;
+
+ nand_davinci_4bit_readecc(mtd, hw_4ecc);
+
+ /*Convert 10 bit ecc value to 8 bit */
+ for (i = 0; i < 2; i++) {
+ unsigned int hw_ecc_low = hw_4ecc[i * 2];
+ unsigned int hw_ecc_hi = hw_4ecc[(i * 2) + 1];
+
+ /* Take first 8 bits from val1 (count1=0) or val5 (count1=1) */
+ *ecc_code++ = hw_ecc_low & 0xFF;
+
+ /*
+ * Take 2 bits as LSB bits from val1 (count1=0) or val5
+ * (count1=1) and 6 bits from val2 (count1=0) or
+ * val5 (count1=1)
+ */
+ *ecc_code++ =
+ ((hw_ecc_low >> 8) & 0x3) | ((hw_ecc_low >> 14) & 0xFC);
+
+ /*
+ * Take 4 bits from val2 (count1=0) or val5 (count1=1) and
+ * 4 bits from val3 (count1=0) or val6 (count1=1)
+ */
+ *ecc_code++ =
+ ((hw_ecc_low >> 22) & 0xF) | ((hw_ecc_hi << 4) & 0xF0);
+
+ /*
+ * Take 6 bits from val3(count1=0) or val6 (count1=1) and
+ * 2 bits from val4 (count1=0) or val7 (count1=1)
+ */
+ *ecc_code++ =
+ ((hw_ecc_hi >> 4) & 0x3F) | ((hw_ecc_hi >> 10) & 0xC0);
+
+ /* Take 8 bits from val4 (count1=0) or val7 (count1=1) */
+ *ecc_code++ = (hw_ecc_hi >> 18) & 0xFF;
+ }
+
+ return 0;
+}
+
+static int nand_davinci_4bit_correct_data(struct mtd_info *mtd, uint8_t *dat,
+ uint8_t *read_ecc, uint8_t *calc_ecc)
+{
+ int i;
+ unsigned int hw_4ecc[4];
+ unsigned int iserror;
+ unsigned short *ecc16;
+ unsigned int numerrors, erroraddress, errorvalue;
+ u32 val;
+
+ /*
+ * Check for an ECC where all bytes are 0xFF. If this is the case, we
+ * will assume we are looking at an erased page and we should ignore
+ * the ECC.
+ */
+ for (i = 0; i < 10; i++) {
+ if (read_ecc[i] != 0xFF)
+ break;
+ }
+ if (i == 10)
+ return 0;
+
+ /* Convert 8 bit in to 10 bit */
+ ecc16 = (unsigned short *)&read_ecc[0];
+
+ /*
+ * Write the parity values in the NAND Flash 4-bit ECC Load register.
+ * Write each parity value one at a time starting from 4bit_ecc_val8
+ * to 4bit_ecc_val1.
+ */
+
+ /*Take 2 bits from 8th byte and 8 bits from 9th byte */
+ __raw_writel(((ecc16[4]) >> 6) & 0x3FF,
+ &davinci_emif_regs->nand4biteccload);
+
+ /* Take 4 bits from 7th byte and 6 bits from 8th byte */
+ __raw_writel((((ecc16[3]) >> 12) & 0xF) | ((((ecc16[4])) << 4) & 0x3F0),
+ &davinci_emif_regs->nand4biteccload);
+
+ /* Take 6 bits from 6th byte and 4 bits from 7th byte */
+ __raw_writel((ecc16[3] >> 2) & 0x3FF,
+ &davinci_emif_regs->nand4biteccload);
+
+ /* Take 8 bits from 5th byte and 2 bits from 6th byte */
+ __raw_writel(((ecc16[2]) >> 8) | ((((ecc16[3])) << 8) & 0x300),
+ &davinci_emif_regs->nand4biteccload);
+
+ /*Take 2 bits from 3rd byte and 8 bits from 4th byte */
+ __raw_writel((((ecc16[1]) >> 14) & 0x3) | ((((ecc16[2])) << 2) & 0x3FC),
+ &davinci_emif_regs->nand4biteccload);
+
+ /* Take 4 bits form 2nd bytes and 6 bits from 3rd bytes */
+ __raw_writel(((ecc16[1]) >> 4) & 0x3FF,
+ &davinci_emif_regs->nand4biteccload);
+
+ /* Take 6 bits from 1st byte and 4 bits from 2nd byte */
+ __raw_writel((((ecc16[0]) >> 10) & 0x3F) | (((ecc16[1]) << 6) & 0x3C0),
+ &davinci_emif_regs->nand4biteccload);
+
+ /* Take 10 bits from 0th and 1st bytes */
+ __raw_writel((ecc16[0]) & 0x3FF,
+ &davinci_emif_regs->nand4biteccload);
+
+ /*
+ * Perform a dummy read to the EMIF Revision Code and Status register.
+ * This is required to ensure time for syndrome calculation after
+ * writing the ECC values in previous step.
+ */
+
+ val = __raw_readl(&davinci_emif_regs->nandfsr);
+
+ /*
+ * Read the syndrome from the NAND Flash 4-Bit ECC 1-4 registers.
+ * A syndrome value of 0 means no bit errors. If the syndrome is
+ * non-zero then go further otherwise return.
+ */
+ nand_davinci_4bit_readecc(mtd, hw_4ecc);
+
+ if (!(hw_4ecc[0] | hw_4ecc[1] | hw_4ecc[2] | hw_4ecc[3]))
+ return 0;
+
+ /*
+ * Clear any previous address calculation by doing a dummy read of an
+ * error address register.
+ */
+ val = __raw_readl(&davinci_emif_regs->nanderradd1);
+
+ /*
+ * Set the addr_calc_st bit(bit no 13) in the NAND Flash Control
+ * register to 1.
+ */
+ __raw_writel(DAVINCI_NANDFCR_4BIT_CALC_START,
+ &davinci_emif_regs->nandfcr);
+
+ /*
+ * Wait for the corr_state field (bits 8 to 11) in the
+ * NAND Flash Status register to be not equal to 0x0, 0x1, 0x2, or 0x3.
+ * Otherwise ECC calculation has not even begun and the next loop might
+ * fail because of a false positive!
+ */
+ i = NAND_TIMEOUT;
+ do {
+ val = __raw_readl(&davinci_emif_regs->nandfsr);
+ val &= 0xc00;
+ i--;
+ } while ((i > 0) && !val);
+
+ /*
+ * Wait for the corr_state field (bits 8 to 11) in the
+ * NAND Flash Status register to be equal to 0x0, 0x1, 0x2, or 0x3.
+ */
+ i = NAND_TIMEOUT;
+ do {
+ val = __raw_readl(&davinci_emif_regs->nandfsr);
+ val &= 0xc00;
+ i--;
+ } while ((i > 0) && val);
+
+ iserror = __raw_readl(&davinci_emif_regs->nandfsr);
+ iserror &= EMIF_NANDFSR_ECC_STATE_MASK;
+ iserror = iserror >> 8;
+
+ /*
+ * ECC_STATE_TOO_MANY_ERRS (0x1) means errors cannot be
+ * corrected (five or more errors). The number of errors
+ * calculated (err_num field) differs from the number of errors
+ * searched. ECC_STATE_ERR_CORR_COMP_P (0x2) means error
+ * correction complete (errors on bit 8 or 9).
+ * ECC_STATE_ERR_CORR_COMP_N (0x3) means error correction
+ * complete (error exists).
+ */
+
+ if (iserror == ECC_STATE_NO_ERR) {
+ val = __raw_readl(&davinci_emif_regs->nanderrval1);
+ return 0;
+ } else if (iserror == ECC_STATE_TOO_MANY_ERRS) {
+ val = __raw_readl(&davinci_emif_regs->nanderrval1);
+ return -1;
+ }
+
+ numerrors = ((__raw_readl(&davinci_emif_regs->nandfsr) >> 16)
+ & 0x3) + 1;
+
+ /* Read the error address, error value and correct */
+ for (i = 0; i < numerrors; i++) {
+ if (i > 1) {
+ erroraddress =
+ ((__raw_readl(&davinci_emif_regs->nanderradd2) >>
+ (16 * (i & 1))) & 0x3FF);
+ erroraddress = ((512 + 7) - erroraddress);
+ errorvalue =
+ ((__raw_readl(&davinci_emif_regs->nanderrval2) >>
+ (16 * (i & 1))) & 0xFF);
+ } else {
+ erroraddress =
+ ((__raw_readl(&davinci_emif_regs->nanderradd1) >>
+ (16 * (i & 1))) & 0x3FF);
+ erroraddress = ((512 + 7) - erroraddress);
+ errorvalue =
+ ((__raw_readl(&davinci_emif_regs->nanderrval1) >>
+ (16 * (i & 1))) & 0xFF);
+ }
+ /* xor the corrupt data with error value */
+ if (erroraddress < 512)
+ dat[erroraddress] ^= errorvalue;
+ }
+
+ return numerrors;
+}
+#endif /* CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST */
+
+static int nand_davinci_dev_ready(struct mtd_info *mtd)
+{
+ return __raw_readl(&davinci_emif_regs->nandfsr) & 0x1;
+}
+
+static void nand_flash_init(void)
+{
+ /* This is for DM6446 EVM and *very* similar. DO NOT GROW THIS!
+ * Instead, have your board_init() set EMIF timings, based on its
+ * knowledge of the clocks and what devices are hooked up ... and
+ * don't even do that unless no UBL handled it.
+ */
+#ifdef CONFIG_SOC_DM644X
+ u_int32_t acfg1 = 0x3ffffffc;
+
+ /*------------------------------------------------------------------*
+ * NAND FLASH CHIP TIMEOUT @ 459 MHz *
+ * *
+ * AEMIF.CLK freq = PLL1/6 = 459/6 = 76.5 MHz *
+ * AEMIF.CLK period = 1/76.5 MHz = 13.1 ns *
+ * *
+ *------------------------------------------------------------------*/
+ acfg1 = 0
+ | (0 << 31) /* selectStrobe */
+ | (0 << 30) /* extWait */
+ | (1 << 26) /* writeSetup 10 ns */
+ | (3 << 20) /* writeStrobe 40 ns */
+ | (1 << 17) /* writeHold 10 ns */
+ | (1 << 13) /* readSetup 10 ns */
+ | (5 << 7) /* readStrobe 60 ns */
+ | (1 << 4) /* readHold 10 ns */
+ | (3 << 2) /* turnAround ?? ns */
+ | (0 << 0) /* asyncSize 8-bit bus */
+ ;
+
+ __raw_writel(acfg1, &davinci_emif_regs->ab1cr); /* CS2 */
+
+ /* NAND flash on CS2 */
+ __raw_writel(0x00000101, &davinci_emif_regs->nandfcr);
+#endif
+}
+
+void davinci_nand_init(struct nand_chip *nand)
+{
+ nand->chip_delay = 0;
+#ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
+ nand->bbt_options |= NAND_BBT_USE_FLASH;
+#endif
+#ifdef CONFIG_SYS_NAND_HW_ECC
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.size = 512;
+ nand->ecc.bytes = 3;
+ nand->ecc.strength = 1;
+ nand->ecc.calculate = nand_davinci_calculate_ecc;
+ nand->ecc.correct = nand_davinci_correct_data;
+ nand->ecc.hwctl = nand_davinci_enable_hwecc;
+#else
+ nand->ecc.mode = NAND_ECC_SOFT;
+#endif /* CONFIG_SYS_NAND_HW_ECC */
+#ifdef CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
+ nand->ecc.mode = NAND_ECC_HW_OOB_FIRST;
+ nand->ecc.size = 512;
+ nand->ecc.bytes = 10;
+ nand->ecc.strength = 4;
+ nand->ecc.calculate = nand_davinci_4bit_calculate_ecc;
+ nand->ecc.correct = nand_davinci_4bit_correct_data;
+ nand->ecc.hwctl = nand_davinci_4bit_enable_hwecc;
+ nand->ecc.layout = &nand_davinci_4bit_layout_oobfirst;
+#endif
+ /* Set address of hardware control function */
+ nand->cmd_ctrl = nand_davinci_hwcontrol;
+
+ nand->read_buf = nand_davinci_read_buf;
+ nand->write_buf = nand_davinci_write_buf;
+
+ nand->dev_ready = nand_davinci_dev_ready;
+
+ nand_flash_init();
+}
+
+int board_nand_init(struct nand_chip *chip) __attribute__((weak));
+
+int board_nand_init(struct nand_chip *chip)
+{
+ davinci_nand_init(chip);
+ return 0;
+}