ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/marvell/uboot/drivers/usb/musb/am35x.c b/marvell/uboot/drivers/usb/musb/am35x.c
new file mode 100644
index 0000000..62c3a6f
--- /dev/null
+++ b/marvell/uboot/drivers/usb/musb/am35x.c
@@ -0,0 +1,139 @@
+/*
+ * am35x.c - TI's AM35x platform specific usb wrapper functions.
+ *
+ * Author: Ajay Kumar Gupta <ajay.gupta@ti.com>
+ *
+ * Based on drivers/usb/musb/da8xx.c
+ *
+ * Copyright (c) 2010 Texas Instruments Incorporated
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+
+#include "am35x.h"
+
+/* MUSB platform configuration */
+struct musb_config musb_cfg = {
+ .regs = (struct musb_regs *)AM35X_USB_OTG_CORE_BASE,
+ .timeout = AM35X_USB_OTG_TIMEOUT,
+ .musb_speed = 0,
+};
+
+/*
+ * Enable the USB phy
+ */
+static u8 phy_on(void)
+{
+ u32 devconf2;
+ u32 timeout;
+
+ devconf2 = readl(&am35x_scm_general_regs->devconf2);
+
+ devconf2 &= ~(DEVCONF2_RESET | DEVCONF2_PHYPWRDN | DEVCONF2_OTGPWRDN |
+ DEVCONF2_OTGMODE | DEVCONF2_REFFREQ |
+ DEVCONF2_PHY_GPIOMODE);
+ devconf2 |= DEVCONF2_SESENDEN | DEVCONF2_VBDTCTEN | DEVCONF2_PHY_PLLON |
+ DEVCONF2_REFFREQ_13MHZ | DEVCONF2_DATPOL;
+
+ writel(devconf2, &am35x_scm_general_regs->devconf2);
+
+ /* wait until the USB phy is turned on */
+ timeout = musb_cfg.timeout;
+ while (timeout--)
+ if (readl(&am35x_scm_general_regs->devconf2) & DEVCONF2_PHYCKGD)
+ return 1;
+
+ /* USB phy was not turned on */
+ return 0;
+}
+
+/*
+ * Disable the USB phy
+ */
+static void phy_off(void)
+{
+ u32 devconf2;
+
+ /*
+ * Power down the on-chip PHY.
+ */
+ devconf2 = readl(&am35x_scm_general_regs->devconf2);
+
+ devconf2 &= ~DEVCONF2_PHY_PLLON;
+ devconf2 |= DEVCONF2_PHYPWRDN | DEVCONF2_OTGPWRDN;
+ writel(devconf2, &am35x_scm_general_regs->devconf2);
+}
+
+/*
+ * This function performs platform specific initialization for usb0.
+ */
+int musb_platform_init(void)
+{
+ u32 revision;
+ u32 sw_reset;
+
+ /* global usb reset */
+ sw_reset = readl(&am35x_scm_general_regs->ip_sw_reset);
+ sw_reset |= (1 << 0);
+ writel(sw_reset, &am35x_scm_general_regs->ip_sw_reset);
+ sw_reset &= ~(1 << 0);
+ writel(sw_reset, &am35x_scm_general_regs->ip_sw_reset);
+
+ /* reset the controller */
+ writel(0x1, &am35x_usb_regs->control);
+ udelay(5000);
+
+ /* start the on-chip usb phy and its pll */
+ if (phy_on() == 0)
+ return -1;
+
+ /* Returns zero if e.g. not clocked */
+ revision = readl(&am35x_usb_regs->revision);
+ if (revision == 0)
+ return -1;
+
+ return 0;
+}
+
+/*
+ * This function performs platform specific deinitialization for usb0.
+ */
+void musb_platform_deinit(void)
+{
+ /* Turn off the phy */
+ phy_off();
+}
+
+/*
+ * This function reads data from endpoint fifo for AM35x
+ * which supports only 32bit read operation.
+ *
+ * ep - endpoint number
+ * length - number of bytes to read from FIFO
+ * fifo_data - pointer to data buffer into which data is read
+ */
+__attribute__((weak))
+void read_fifo(u8 ep, u32 length, void *fifo_data)
+{
+ u8 *data = (u8 *)fifo_data;
+ u32 val;
+ int i;
+
+ /* select the endpoint index */
+ writeb(ep, &musbr->index);
+
+ if (length > 4) {
+ for (i = 0; i < (length >> 2); i++) {
+ val = readl(&musbr->fifox[ep]);
+ memcpy(data, &val, 4);
+ data += 4;
+ }
+ length %= 4;
+ }
+ if (length > 0) {
+ val = readl(&musbr->fifox[ep]);
+ memcpy(data, &val, length);
+ }
+}