ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/package/base-files/files/bin/config_generate b/package/base-files/files/bin/config_generate
new file mode 100755
index 0000000..a9d8837
--- /dev/null
+++ b/package/base-files/files/bin/config_generate
@@ -0,0 +1,548 @@
+#!/bin/sh
+
+CFG=/etc/board.json
+
+. /usr/share/libubox/jshn.sh
+
+[ -s $CFG ] || /bin/board_detect || exit 1
+[ -s /etc/config/network -a -s /etc/config/system ] && exit 0
+
+generate_bridge() {
+ local name=$1
+ local macaddr=$2
+ uci -q batch <<-EOF
+ set network.$name=device
+ set network.$name.name=$name
+ set network.$name.type=bridge
+ EOF
+ if [ -n "$macaddr" ]; then
+ uci -q batch <<-EOF
+ set network.$name.macaddr=$macaddr
+ EOF
+ fi
+}
+
+bridge_vlan_id=0
+generate_bridge_vlan() {
+ local name=$1_vlan
+ local device=$2
+ local ports="$3"
+ local vlan="$4"
+ uci -q batch <<-EOF
+ set network.$name=bridge-vlan
+ set network.$name.device='$device'
+ set network.$name.vlan='$vlan'
+ set network.$name.ports='$ports'
+ EOF
+}
+
+generate_static_network() {
+ uci -q batch <<-EOF
+ delete network.loopback
+ set network.loopback='interface'
+ set network.loopback.device='lo'
+ set network.loopback.proto='static'
+ set network.loopback.ipaddr='127.0.0.1'
+ set network.loopback.netmask='255.0.0.0'
+ EOF
+ [ -e /proc/sys/net/ipv6 ] && {
+ uci -q batch <<-EOF
+ delete network.globals
+ set network.globals='globals'
+ set network.globals.ula_prefix='auto'
+ EOF
+ }
+
+ if json_is_a dsl object; then
+ json_select dsl
+ if json_is_a atmbridge object; then
+ json_select atmbridge
+ local vpi vci encaps payload nameprefix
+ json_get_vars vpi vci encaps payload nameprefix
+ uci -q batch <<-EOF
+ delete network.atm
+ set network.atm='atm-bridge'
+ set network.atm.vpi='$vpi'
+ set network.atm.vci='$vci'
+ set network.atm.encaps='$encaps'
+ set network.atm.payload='$payload'
+ set network.atm.nameprefix='$nameprefix'
+ EOF
+ json_select ..
+ fi
+
+ if json_is_a modem object; then
+ json_select modem
+ local type annex firmware tone xfer_mode
+ json_get_vars type annex firmware tone xfer_mode
+ uci -q batch <<-EOF
+ delete network.dsl
+ set network.dsl='dsl'
+ set network.dsl.annex='$annex'
+ set network.dsl.firmware='$firmware'
+ set network.dsl.tone='$tone'
+ set network.dsl.xfer_mode='$xfer_mode'
+ EOF
+ json_select ..
+ fi
+ json_select ..
+ fi
+}
+
+addr_offset=2
+generate_network() {
+ local ports device macaddr protocol type ipaddr netmask vlan
+ local bridge=$2
+
+ json_select network
+ json_select "$1"
+ json_get_vars device macaddr metric protocol ipaddr netmask vlan
+ json_get_values ports ports
+ json_select ..
+ json_select ..
+
+ [ -n "$device" -o -n "$ports" ] || return
+
+ # Force bridge for "lan" as it may have other devices (e.g. wireless)
+ # bridged
+ [ "$1" = "lan" -a -z "$ports" ] && {
+ ports="$device"
+ }
+
+ [ -n "$ports" -a -z "$bridge" ] && {
+ uci -q batch <<-EOF
+ add network device
+ set network.@device[-1].name='br-$1'
+ set network.@device[-1].type='bridge'
+ EOF
+ for port in $ports; do uci add_list network.@device[-1].ports="$port"; done
+ [ -n "$macaddr" ] && {
+ for port in $ports; do
+ uci -q batch <<-EOF
+ add network device
+ set network.@device[-1].name='$port'
+ set network.@device[-1].macaddr='$macaddr'
+ EOF
+ done
+ }
+ device=br-$1
+ type=
+ macaddr=""
+ }
+
+ [ -n "$bridge" ] && {
+ [ -z "$ports" ] && ports="$device"
+ if [ -z "$vlan" ]; then
+ bridge_vlan_id=$((bridge_vlan_id + 1))
+ vlan=$bridge_vlan_id
+ fi
+ generate_bridge_vlan $1 $bridge "$ports" $vlan
+ device=$bridge.$vlan
+ type=""
+ }
+
+ if [ -n "$macaddr" ]; then
+ uci -q batch <<-EOF
+ add network device
+ set network.@device[-1].name='$device'
+ set network.@device[-1].macaddr='$macaddr'
+ EOF
+ fi
+
+ uci -q batch <<-EOF
+ delete network.$1
+ set network.$1='interface'
+ set network.$1.type='$type'
+ set network.$1.device='$device'
+ set network.$1.metric='$metric'
+ set network.$1.proto='none'
+ EOF
+
+ case "$protocol" in
+ static)
+ local ipad
+ case "$1" in
+ lan) ipad=${ipaddr:-"192.168.1.1"} ;;
+ *) ipad=${ipaddr:-"192.168.$((addr_offset++)).1"} ;;
+ esac
+
+ netm=${netmask:-"255.255.255.0"}
+
+ uci -q batch <<-EOF
+ set network.$1.proto='static'
+ set network.$1.ipaddr='$ipad'
+ set network.$1.netmask='$netm'
+ EOF
+ [ -e /proc/sys/net/ipv6 ] && uci set network.$1.ip6assign='60'
+ ;;
+
+ dhcp)
+ # fixup IPv6 slave interface if parent is a bridge
+ [ "$type" = "bridge" ] && device="br-$1"
+
+ uci set network.$1.proto='dhcp'
+ [ -e /proc/sys/net/ipv6 ] && {
+ uci -q batch <<-EOF
+ delete network.${1}6
+ set network.${1}6='interface'
+ set network.${1}6.device='$device'
+ set network.${1}6.proto='dhcpv6'
+ EOF
+ }
+ ;;
+
+ pppoe)
+ uci -q batch <<-EOF
+ set network.$1.proto='pppoe'
+ set network.$1.username='username'
+ set network.$1.password='password'
+ EOF
+ [ -e /proc/sys/net/ipv6 ] && {
+ uci -q batch <<-EOF
+ set network.$1.ipv6='1'
+ delete network.${1}6
+ set network.${1}6='interface'
+ set network.${1}6.device='@${1}'
+ set network.${1}6.proto='dhcpv6'
+ EOF
+ }
+ ;;
+
+ ncm|\
+ qmi|\
+ mbim)
+ uci -q batch <<-EOF
+ set network.$1.proto='${protocol}'
+ set network.$1.pdptype='ipv4'
+ EOF
+ ;;
+ esac
+}
+
+generate_switch_vlans_ports() {
+ local switch="$1"
+ local port ports role roles num attr val
+
+ #
+ # autogenerate vlans
+ #
+
+ if json_is_a roles array; then
+ json_get_keys roles roles
+ json_select roles
+
+ for role in $roles; do
+ json_select "$role"
+ json_get_vars ports
+ json_select ..
+
+ uci -q batch <<-EOF
+ add network switch_vlan
+ set network.@switch_vlan[-1].device='$switch'
+ set network.@switch_vlan[-1].vlan='$role'
+ set network.@switch_vlan[-1].ports='$ports'
+ EOF
+ done
+
+ json_select ..
+ fi
+
+
+ #
+ # write port specific settings
+ #
+
+ if json_is_a ports array; then
+ json_get_keys ports ports
+ json_select ports
+
+ for port in $ports; do
+ json_select "$port"
+ json_get_vars num
+
+ if json_is_a attr object; then
+ json_get_keys attr attr
+ json_select attr
+ uci -q batch <<-EOF
+ add network switch_port
+ set network.@switch_port[-1].device='$switch'
+ set network.@switch_port[-1].port=$num
+ EOF
+
+ for attr in $attr; do
+ json_get_var val "$attr"
+ uci -q set network.@switch_port[-1].$attr="$val"
+ done
+ json_select ..
+ fi
+ json_select ..
+ done
+
+ json_select ..
+ fi
+}
+
+generate_switch() {
+ local key="$1"
+ local vlans
+
+ json_select switch
+ json_select "$key"
+ json_get_vars enable reset blinkrate cpu_port \
+ ar8xxx_mib_type ar8xxx_mib_poll_interval
+
+ uci -q batch <<-EOF
+ add network switch
+ set network.@switch[-1].name='$key'
+ set network.@switch[-1].reset='$reset'
+ set network.@switch[-1].enable_vlan='$enable'
+ set network.@switch[-1].blinkrate='$blinkrate'
+ set network.@switch[-1].ar8xxx_mib_type='$ar8xxx_mib_type'
+ set network.@switch[-1].ar8xxx_mib_poll_interval='$ar8xxx_mib_poll_interval'
+ EOF
+
+ generate_switch_vlans_ports "$1"
+
+ json_select ..
+ json_select ..
+}
+
+generate_static_system() {
+ uci -q batch <<-EOF
+ delete system.@system[0]
+ add system system
+ set system.@system[-1].hostname='OpenWrt'
+ set system.@system[-1].timezone='CST-8'
+ set system.@system[-1].zonename='Asia/Shanghai'
+ set system.@system[-1].ttylogin='0'
+ set system.@system[-1].log_size='64'
+ set system.@system[-1].urandom_seed='0'
+
+ delete system.ntp
+ set system.ntp='timeserver'
+ set system.ntp.enabled='1'
+ set system.ntp.enable_server='0'
+ add_list system.ntp.server='0.openwrt.pool.ntp.org'
+ add_list system.ntp.server='1.openwrt.pool.ntp.org'
+ add_list system.ntp.server='2.openwrt.pool.ntp.org'
+ add_list system.ntp.server='3.openwrt.pool.ntp.org'
+ EOF
+
+ if json_is_a system object; then
+ json_select system
+ local hostname
+ if json_get_var hostname hostname; then
+ uci -q set "system.@system[-1].hostname=$hostname"
+ fi
+
+ local compat_version
+ if json_get_var compat_version compat_version; then
+ uci -q set "system.@system[-1].compat_version=$compat_version"
+ else
+ uci -q set "system.@system[-1].compat_version=1.0"
+ fi
+
+ local timezone
+ if json_get_var timezone timezone; then
+ uci -q set "system.@system[-1].timezone=$timezone"
+ fi
+
+ if json_is_a ntpserver array; then
+ local keys key
+ json_get_keys keys ntpserver
+ json_select ntpserver
+ uci -q delete "system.ntp.server"
+
+ for key in $keys; do
+ local server
+ if json_get_var server "$key"; then
+ uci -q add_list "system.ntp.server=$server"
+ fi
+ done
+ json_select ..
+ fi
+ json_select ..
+ fi
+}
+
+generate_rssimon() {
+ local key="$1"
+ local cfg="rssid_$key"
+ local refresh threshold
+
+ json_select rssimon
+ json_select "$key"
+ json_get_vars refresh threshold
+ json_select ..
+ json_select ..
+
+ uci -q batch <<-EOF
+ delete system.$cfg
+ set system.$cfg='rssid'
+ set system.$cfg.dev='$key'
+ set system.$cfg.refresh='$refresh'
+ set system.$cfg.threshold='$threshold'
+ EOF
+}
+
+generate_led() {
+ local key="$1"
+ local cfg="led_$key"
+
+ json_select led
+ json_select "$key"
+ json_get_vars name sysfs type trigger default
+
+ uci -q batch <<-EOF
+ delete system.$cfg
+ set system.$cfg='led'
+ set system.$cfg.name='$name'
+ set system.$cfg.sysfs='$sysfs'
+ set system.$cfg.trigger='$trigger'
+ set system.$cfg.default='$default'
+ EOF
+
+ case "$type" in
+ gpio)
+ local gpio inverted
+ json_get_vars gpio inverted
+ uci -q batch <<-EOF
+ set system.$cfg.trigger='gpio'
+ set system.$cfg.gpio='$gpio'
+ set system.$cfg.inverted='$inverted'
+ EOF
+ ;;
+
+ netdev)
+ local device mode
+ json_get_vars device mode
+ uci -q batch <<-EOF
+ set system.$cfg.trigger='netdev'
+ set system.$cfg.mode='$mode'
+ set system.$cfg.dev='$device'
+ EOF
+ ;;
+
+ usb)
+ local device
+ json_get_vars device
+ uci -q batch <<-EOF
+ set system.$cfg.trigger='usbdev'
+ set system.$cfg.interval='50'
+ set system.$cfg.dev='$device'
+ EOF
+ ;;
+
+ usbport)
+ local ports port
+ json_get_values ports ports
+ uci set system.$cfg.trigger='usbport'
+ for port in $ports; do
+ uci add_list system.$cfg.port=$port
+ done
+ ;;
+
+ rssi)
+ local iface minq maxq offset factor
+ json_get_vars iface minq maxq offset factor
+ uci -q batch <<-EOF
+ set system.$cfg.trigger='rssi'
+ set system.$cfg.iface='rssid_$iface'
+ set system.$cfg.minq='$minq'
+ set system.$cfg.maxq='$maxq'
+ set system.$cfg.offset='$offset'
+ set system.$cfg.factor='$factor'
+ EOF
+ ;;
+
+ switch)
+ local port_mask speed_mask mode
+ json_get_vars port_mask speed_mask mode
+ uci -q batch <<-EOF
+ set system.$cfg.port_mask='$port_mask'
+ set system.$cfg.speed_mask='$speed_mask'
+ set system.$cfg.mode='$mode'
+ EOF
+ ;;
+
+ portstate)
+ local port_state
+ json_get_vars port_state
+ uci -q batch <<-EOF
+ set system.$cfg.port_state='$port_state'
+ EOF
+ ;;
+
+ timer|oneshot)
+ local delayon delayoff
+ json_get_vars delayon delayoff
+ uci -q batch <<-EOF
+ set system.$cfg.trigger='$type'
+ set system.$cfg.delayon='$delayon'
+ set system.$cfg.delayoff='$delayoff'
+ EOF
+ ;;
+ esac
+
+ json_select ..
+ json_select ..
+}
+
+generate_gpioswitch() {
+ local cfg="$1"
+
+ json_select gpioswitch
+ json_select "$cfg"
+ local name pin default
+ json_get_vars name pin default
+ uci -q batch <<-EOF
+ delete system.$cfg
+ set system.$cfg='gpio_switch'
+ set system.$cfg.name='$name'
+ set system.$cfg.gpio_pin='$pin'
+ set system.$cfg.value='$default'
+ EOF
+ json_select ..
+ json_select ..
+}
+
+json_init
+json_load "$(cat ${CFG})"
+
+umask 077
+
+if [ ! -s /etc/config/network ]; then
+ bridge_name=""
+ touch /etc/config/network
+ generate_static_network
+
+ json_get_vars bridge
+ [ -n "$bridge" ] && {
+ json_select bridge
+ json_get_vars name macaddr
+ generate_bridge "$name" "$macaddr"
+ json_select ..
+ bridge_name=$name
+ }
+
+ json_get_keys keys network
+ for key in $keys; do generate_network $key $bridge_name; done
+
+ json_get_keys keys switch
+ for key in $keys; do generate_switch $key; done
+fi
+
+if [ ! -s /etc/config/system ]; then
+ touch /etc/config/system
+ generate_static_system
+
+ json_get_keys keys rssimon
+ for key in $keys; do generate_rssimon $key; done
+
+ json_get_keys keys gpioswitch
+ for key in $keys; do generate_gpioswitch $key; done
+
+ json_get_keys keys led
+ for key in $keys; do generate_led $key; done
+fi
+uci commit