ASR_BASE
Change-Id: Icf3719cc0afe3eeb3edc7fa80a2eb5199ca9dda1
diff --git a/target/linux/ath79/dts/ar9331_arduino_yun.dts b/target/linux/ath79/dts/ar9331_arduino_yun.dts
new file mode 100644
index 0000000..389a83d
--- /dev/null
+++ b/target/linux/ath79/dts/ar9331_arduino_yun.dts
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9331.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Arduino Yun";
+ compatible = "arduino,yun", "qca,ar9331";
+
+ chosen {
+ bootargs = "console=ttyATH0,250000";
+ };
+
+ ahb {
+ apb {
+ pinmux_extended: pinmux@18040030 {
+ compatible = "pinctrl-single";
+ reg = <0x18040030 0x4>;
+
+ pinctrl-single,bit-per-mux;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x1>;
+ #pinctrl-cells = <2>;
+
+ enable_gpio11: pinmux_enable_gpio11 {
+ pinctrl-single,bits = <0x0 0x200 0x200>;
+ };
+ };
+
+ pinmux_bootstrap: pinmux@180600ac {
+ compatible = "pinctrl-single";
+ reg = <0x180600ac 0x4>;
+
+ pinctrl-single,bit-per-mux;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x1>;
+ #pinctrl-cells = <2>;
+
+ enable_gpio26_gpio27: pinmux_enable_gpio26_gpio27 {
+ pinctrl-single,bits = <0x0 0x40000 0x40000>;
+ };
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wlan {
+ label = "blue:wlan";
+ gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ usb {
+ label = "white:usb";
+ gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+ trigger-sources = <&hub_port1>;
+ linux,default-trigger = "usbport";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ config {
+ label = "config";
+ linux,code = <BTN_0>;
+ gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ gpio_spi_enable {
+ gpio-export,name = "yun:oe:spi";
+ gpio-export,output = <0>;
+ gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_handshake_enable {
+ gpio-export,name = "yun:oe:hs";
+ gpio-export,output = <0>;
+ gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_uart_enable {
+ gpio-export,name = "yun:oe:uart";
+ gpio-export,output = <0>;
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_usb_vbus: reg_usb_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ };
+};
+
+&pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&jtag_disable_pins &switch_led_disable_pins>;
+};
+
+&switch_led_disable_pins {
+ pinctrl-single,bits = <0x0 0x80 0xf8>;
+};
+
+&pinmux_extended {
+ pinctrl-names = "default";
+ pinctrl-0 = <&enable_gpio11>;
+};
+
+&pinmux_bootstrap {
+ pinctrl-names = "default";
+ pinctrl-0 = <&enable_gpio26_gpio27>;
+};
+
+&usb {
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dr_mode = "host";
+ vbus-supply = <®_usb_vbus>;
+
+ port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ #trigger-source-cells = <0>;
+
+ hub_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+ };
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x40000 0x10000>;
+ };
+
+ partition@50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x50000 0xf90000>;
+ };
+
+ partition@fe0000 {
+ label = "nvram";
+ reg = <0xfe0000 0x10000>;
+ };
+
+ art: partition@ff0000 {
+ label = "art";
+ reg = <0xff0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+};
+
+ð1 {
+ status = "okay";
+
+ compatible = "syscon", "simple-mfd";
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+};