diff --git a/target/linux/layerscape/patches-5.4/808-i2c-0008-i2c-imx-implement-bus-recovery-with-gpio-for-Layersc.patch b/target/linux/layerscape/patches-5.4/808-i2c-0008-i2c-imx-implement-bus-recovery-with-gpio-for-Layersc.patch
new file mode 100644
index 0000000..f7686f3
--- /dev/null
+++ b/target/linux/layerscape/patches-5.4/808-i2c-0008-i2c-imx-implement-bus-recovery-with-gpio-for-Layersc.patch
@@ -0,0 +1,268 @@
+From ddf55be668a5e5a22d4b7729e7ba92d928983168 Mon Sep 17 00:00:00 2001
+From: Zhang Ying-22455 <ying.zhang22455@nxp.com>
+Date: Fri, 1 Dec 2017 15:59:28 +0800
+Subject: [PATCH] i2c: imx: implement bus recovery with gpio for Layerscape
+
+Based on the I2C specification, if the data line (SDA) is stuck low,
+the master should send nine clock pulses. The I2C slave device that
+held the bus low should release it sometime within those nine clocks.
+
+Because pinctrl is not supported on Layerscape, current bus recovery
+is not avalible for Layerscape. This patch uses an open drain GPIO
+pin to connect to the IICx_SCL to drive nine clock pulses to unlock
+the I2C bus.
+
+Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
+---
+ drivers/i2c/busses/i2c-imx.c | 190 ++++++++++++++++++++++++++++++++++++++++++-
+ 1 file changed, 188 insertions(+), 2 deletions(-)
+
+--- a/drivers/i2c/busses/i2c-imx.c
++++ b/drivers/i2c/busses/i2c-imx.c
+@@ -39,12 +39,18 @@
+ #include <linux/of.h>
+ #include <linux/of_device.h>
+ #include <linux/of_dma.h>
++#include <linux/of_gpio.h>
+ #include <linux/pinctrl/consumer.h>
+ #include <linux/platform_data/i2c-imx.h>
+ #include <linux/platform_device.h>
+ #include <linux/pm_runtime.h>
+ #include <linux/sched.h>
+ #include <linux/slab.h>
++#include <linux/gpio.h>
++#include <linux/of_address.h>
++#include <linux/of.h>
++#include <linux/of_device.h>
++#include <linux/libata.h>
+ 
+ /* This will be the driver name the kernel reports */
+ #define DRIVER_NAME "imx-i2c"
+@@ -110,6 +116,54 @@
+ 
+ #define I2C_PM_TIMEOUT		10 /* ms */
+ 
++enum pinmux_endian_type {
++	BIG_ENDIAN,
++	LITTLE_ENDIAN,
++};
++
++struct pinmux_cfg {
++	enum pinmux_endian_type endian; /* endian of RCWPMUXCR0 */
++	u32 pmuxcr_offset;
++	u32 pmuxcr_set_bit;		    /* pin mux of RCWPMUXCR0 */
++};
++
++static struct pinmux_cfg ls1012a_pinmux_cfg = {
++	.endian = BIG_ENDIAN,
++	.pmuxcr_offset = 0x430,
++	.pmuxcr_set_bit = 0x10,
++};
++
++static struct pinmux_cfg ls1043a_pinmux_cfg = {
++	.endian = BIG_ENDIAN,
++	.pmuxcr_offset = 0x40C,
++	.pmuxcr_set_bit = 0x10,
++};
++
++static struct pinmux_cfg ls1046a_pinmux_cfg = {
++	.endian = BIG_ENDIAN,
++	.pmuxcr_offset = 0x40C,
++	.pmuxcr_set_bit = 0x80000000,
++};
++
++static const struct of_device_id pinmux_of_match[] = {
++	{ .compatible = "fsl,ls1012a-vf610-i2c", .data = &ls1012a_pinmux_cfg},
++	{ .compatible = "fsl,ls1043a-vf610-i2c", .data = &ls1043a_pinmux_cfg},
++	{ .compatible = "fsl,ls1046a-vf610-i2c", .data = &ls1046a_pinmux_cfg},
++	{},
++};
++MODULE_DEVICE_TABLE(of, pinmux_of_match);
++
++/* The SCFG, Supplemental Configuration Unit, provides SoC specific
++ * configuration and status registers for the device. There is a
++ * SDHC IO VSEL control register on SCFG for some platforms. It's
++ * used to support SDHC IO voltage switching.
++ */
++static const struct of_device_id scfg_device_ids[] = {
++	{ .compatible = "fsl,ls1012a-scfg", },
++	{ .compatible = "fsl,ls1043a-scfg", },
++	{ .compatible = "fsl,ls1046a-scfg", },
++	{}
++};
+ /*
+  * sorted list of clock divider, register value pairs
+  * taken from table 26-5, p.26-9, Freescale i.MX
+@@ -205,6 +259,12 @@ struct imx_i2c_struct {
+ 	struct pinctrl_state *pinctrl_pins_gpio;
+ 
+ 	struct imx_i2c_dma	*dma;
++	int			layerscape_bus_recover;
++	int 			gpio;
++	int			need_set_pmuxcr;
++	int			pmuxcr_set;
++	int			pmuxcr_endian;
++	void __iomem		*pmuxcr_addr;
+ };
+ 
+ static const struct imx_i2c_hwdata imx1_i2c_hwdata = {
+@@ -951,6 +1011,78 @@ static int i2c_imx_read(struct imx_i2c_s
+ 	return 0;
+ }
+ 
++/*
++ * Based on the I2C specification, if the data line (SDA) is
++ * stuck low, the master should send nine  * clock pulses.
++ * The I2C slave device that held the bus low should release it
++ * sometime within  * those nine clocks. Due to this erratum,
++ * the I2C controller cannot generate nine clock pulses.
++ */
++static int i2c_imx_recovery_for_layerscape(struct imx_i2c_struct *i2c_imx)
++{
++	u32 pmuxcr = 0;
++	int ret;
++	unsigned int i, temp;
++
++	/* configure IICx_SCL/GPIO pin as a GPIO */
++	if (i2c_imx->need_set_pmuxcr == 1) {
++		pmuxcr = ioread32be(i2c_imx->pmuxcr_addr);
++		if (i2c_imx->pmuxcr_endian == BIG_ENDIAN)
++			iowrite32be(i2c_imx->pmuxcr_set|pmuxcr,
++				    i2c_imx->pmuxcr_addr);
++		else
++			iowrite32(i2c_imx->pmuxcr_set|pmuxcr,
++				  i2c_imx->pmuxcr_addr);
++	}
++
++	ret = gpio_request(i2c_imx->gpio, i2c_imx->adapter.name);
++	if (ret) {
++		dev_err(&i2c_imx->adapter.dev,
++			"can't get gpio: %d\n", ret);
++		return ret;
++	}
++
++	/* Configure GPIO pin as an output and open drain. */
++	gpio_direction_output(i2c_imx->gpio, 1);
++	udelay(10);
++
++	/* Write data to generate 9 pulses */
++	for (i = 0; i < 9; i++) {
++		gpio_set_value(i2c_imx->gpio, 1);
++		udelay(10);
++		gpio_set_value(i2c_imx->gpio, 0);
++		udelay(10);
++	}
++	/* ensure that the last level sent is always high */
++	gpio_set_value(i2c_imx->gpio, 1);
++
++	/*
++	 * Set I2Cx_IBCR = 0h00 to generate a STOP and then
++	 * set I2Cx_IBCR = 0h80 to reset
++	 */
++	temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
++	temp &= ~(I2CR_MSTA | I2CR_MTX);
++	imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
++
++	/* Restore the saved value of the register SCFG_RCWPMUXCR0 */
++	if (i2c_imx->need_set_pmuxcr == 1) {
++		if (i2c_imx->pmuxcr_endian == BIG_ENDIAN)
++			iowrite32be(pmuxcr, i2c_imx->pmuxcr_addr);
++		else
++			iowrite32(pmuxcr, i2c_imx->pmuxcr_addr);
++	}
++	/*
++	 * Set I2C_IBSR[IBAL] to clear the IBAL bit if-
++	 * I2C_IBSR[IBAL] = 1
++	 */
++	temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
++	if (temp & I2SR_IAL) {
++		temp &= ~I2SR_IAL;
++		imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2SR);
++	}
++	return 0;
++}
++
+ static int i2c_imx_xfer(struct i2c_adapter *adapter,
+ 						struct i2c_msg *msgs, int num)
+ {
+@@ -973,8 +1105,13 @@ static int i2c_imx_xfer(struct i2c_adapt
+ 	 * before switching to master mode and attempting a Start cycle
+ 	 */
+ 	result =  i2c_imx_bus_busy(i2c_imx, 0);
+-	if (result)
+-		goto out;
++	if (result) {
++		/* timeout */
++		if ((result == -ETIMEDOUT) && (i2c_imx->layerscape_bus_recover == 1))
++			i2c_imx_recovery_for_layerscape(i2c_imx);
++		else
++			goto out;
++	}
+ 
+ 	result = pm_runtime_get_sync(i2c_imx->adapter.dev.parent);
+ 	if (result < 0)
+@@ -1121,6 +1258,50 @@ static int i2c_imx_init_recovery_info(st
+ 	return 0;
+ }
+ 
++/*
++ * switch SCL and SDA to their GPIO function and do some bitbanging
++ * for bus recovery.
++ * There are platforms such as Layerscape that don't support pinctrl, so add
++ * workaround for layerscape, it has no effect for other platforms.
++ */
++static int i2c_imx_init_recovery_for_layerscape(
++		struct imx_i2c_struct *i2c_imx,
++		struct platform_device *pdev)
++{
++	const struct of_device_id *of_id;
++	struct device_node *np		= pdev->dev.of_node;
++	struct pinmux_cfg		*pinmux_cfg;
++	struct device_node *scfg_node;
++	void __iomem *scfg_base = NULL;
++
++	i2c_imx->gpio = of_get_named_gpio(np, "scl-gpios", 0);
++	if (!gpio_is_valid(i2c_imx->gpio)) {
++		dev_info(&pdev->dev, "scl-gpios not found\n");
++		return 0;
++	}
++	pinmux_cfg = devm_kzalloc(&pdev->dev, sizeof(*pinmux_cfg), GFP_KERNEL);
++	if (!pinmux_cfg)
++		return -ENOMEM;
++
++	i2c_imx->need_set_pmuxcr = 0;
++	of_id = of_match_node(pinmux_of_match, np);
++	if (of_id) {
++		pinmux_cfg = (struct pinmux_cfg *)of_id->data;
++		i2c_imx->pmuxcr_endian = pinmux_cfg->endian;
++		i2c_imx->pmuxcr_set = pinmux_cfg->pmuxcr_set_bit;
++		scfg_node = of_find_matching_node(NULL, scfg_device_ids);
++		if (scfg_node) {
++			scfg_base = of_iomap(scfg_node, 0);
++			if (scfg_base) {
++				i2c_imx->pmuxcr_addr = scfg_base + pinmux_cfg->pmuxcr_offset;
++				i2c_imx->need_set_pmuxcr = 1;
++			}
++		}
++	}
++	i2c_imx->layerscape_bus_recover = 1;
++	return 0;
++}
++
+ static u32 i2c_imx_func(struct i2c_adapter *adapter)
+ {
+ 	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL
+@@ -1245,8 +1426,13 @@ static int i2c_imx_probe(struct platform
+ 			i2c_imx, IMX_I2C_I2CR);
+ 	imx_i2c_write_reg(i2c_imx->hwdata->i2sr_clr_opcode, i2c_imx, IMX_I2C_I2SR);
+ 
++#ifdef CONFIG_ARCH_LAYERSCAPE
++	/* Init optional bus recovery for layerscape */
++	ret = i2c_imx_init_recovery_for_layerscape(i2c_imx, pdev);
++#else
+ 	/* Init optional bus recovery function */
+ 	ret = i2c_imx_init_recovery_info(i2c_imx, pdev);
++#endif
+ 	/* Give it another chance if pinctrl used is not ready yet */
+ 	if (ret == -EPROBE_DEFER)
+ 		goto clk_notifier_unregister;